Hello friends,
My LeEco Le Pro3 (727) bricked two days ago and I haven't had any luck turning it back on. It was running LineageOS 8.1 latest official build with an unlocked bootloader, Magisk 16.0, TWRP 3.2.1, and OpenGapps ARM64 8.1 nano. Immediately prior to bricking I was setting it up for bluetooth with my car and was trying to run Google Maps through voice command. As I directed Google Maps to take me to a location, the phone froze, the screen got all "fuzzy" and I got the dreaded blue screen of death.
From that point on I have not been able to turn the phone back on. When I press the power button it will vibrate every 5-10 seconds as though it will turn on but it never does. Ive tried everything I can think of to get to work again including:
- Pressing power button for 2 min, 5 mins, 10 mins
- Pressing power button + vol up (recovery) for 2 min, 5 mins, 10 mins
- Pressing power button + vol down (fastboot) for 2 min, 5 mins, 10 mins
- Pressing power button + vol up + vol down (QFIL MODE) -> Installing Qualcomm driver, downloading "FlashOne2.0", flashing all versions of "qfil files" that I could find but still unable to boot up
- Pressing all different button combinations while plugged in to computer/charger
- Using different cords/chargers/usb ports
- Leaving it to charge overnight/full day then trying to boot up
- Leaving it sitting not charging for a full day then trying to boot up
At this point I'm starting to think it might be a hardware issue but who knows..
Any advice/suggestions would be greatly appreciated.
Thank you.
Where did you buy it from.
I don't have much to add here it seems like you have done everything that you could
Let's clear this up no fashboot right.
Only one thing to try hold power down then plug in USB.
Sent from my LEX727 using xda premium
My one did the same, the issue was motherboard. You should send it back to repair.
mchlbenner said:
Where did you buy it from.
I don't have much to add here it seems like you have done everything that you could
Let's clear this up no fashboot right.
Only one thing to try hold power down then plug in USB.
Sent from my LEX727 using xda premium
Click to expand...
Click to collapse
Thank you for the reply.
It was purchased from a local retailer here in the United States through Google Express. Fortunately I should still be able to return it for a full refund but I would rather have a working phone than my money back.
No flashboot either. It's like the phone just decided to quit working one day. Tried holding power while plugging in USB as well and no change.
marik1 said:
My one did the same, the issue was motherboard. You should send it back to repair.
Click to expand...
Click to collapse
The conclusion I'm reaching at this point too. I'll see what the return policy.
Well if it will not turn on it is hardware issue you should be able to return it.
Sent from my LEX727 using xda premium
That is so strange. The screen going fuzzy like that is indicative of a hardware issue, IMO. I saw that on my laptop once, but that was because I hit the screen too hard. Never seen a BSOD on an Android device before. TIL.
I assume you've already tried an adb logcat. Were you using the original LeEco cable? I heard it has issues since it's not up to spec. 99% hardware failure, but I can't help but think it has something to do with driver communication confusing the device and causing hardware failure (?) if that's even possible.
Just a final update for those curious.
After leaving the phone alone for two days I plugged it into the charger and low and behold it started vibrating and booted up by itself. It was running a Chinese developers editions 720 rom due to the QFIL File I had flashed in my earlier in my attempt to fix it. Battery was drained so I let it charge for a while and everything was fine until I attempted to restart the phone. As the boot animation was loading, I got the blue screen of death for a second time.
I took a quick picture, the phone shut off itself off, and same as before it wouldn't boot again. As other users have suggested it appears to be a hardware issue, likely with the motherboard. Fortunately I was still able to return the phone (purchased through Google Express via a local retailer) and received a full refund. I've since bought another Le Pro3 (727) and hopefully when that one comes in, it won't have any issues.
Thanks to all the users who left suggestions/tips.
shyboi122 said:
Just a final update for those curious.
I've since bought another Le Pro3 (727) and hopefully when that one comes in, it won't have any issues.
Thanks to all the users who left suggestions/tips.
Click to expand...
Click to collapse
You bought the same phone again? :good: You're courageous, lol.
i been experiencing the exact problem like your on my x720, as i boot up the system or enterting the recovery mode the screen go fuzzy on loading screen and shut itself off completly, i can still able access fastboot. As i left it for a while the phone will be able to almost finish the boot then ending it all with a blue screen.
Have anyone found a way to fix this DIY since my phone has past the guarantee plan ?
Related
Hello,
I had been using my i9500 for quite a while now, with no issues.
rooted, Hassan rom , Philz Kernel, worked flawlessly until yesterday.
suddenly my phone started rebooting indefinitely, not entering recovery or download modes.
I tried mashing the buttons a little, and i got to the download mode "Warning" screen (unable to go any further) without holding my power button - meaning only by holding both home and volDown keys.
anyway, this lead me to believe my power button is malfunctioning, yet i can still normally press it (Clicking as usual, as if there is no physical damage) and I did not drop or damage my phone in any way.
all of the online threads are regarding phones stuck on boot animation, yet mine is flashing the "Samsung Galaxy S4 GT-I9500" white over black screen (before the boot animation) and doesnt reach boot animation.
i want to believe my data is still reachable as i have not made any backups lately, this is why I came here.
if anyone has encountered any similar issue, please shed some light as this is the first time i had been unable to solve a "boot loop".
thanks in advance!
(ps, phone is still stuck on the loop, i let it keep doing so overnight to let the battery die, plugged it back in to no avail)
rdordo23 said:
Hello,
I had been using my i9500 for quite a while now, with no issues.
rooted, Hassan rom , Philz Kernel, worked flawlessly until yesterday.
suddenly my phone started rebooting indefinitely, not entering recovery or download modes.
I tried mashing the buttons a little, and i got to the download mode "Warning" screen (unable to go any further) without holding my power button - meaning only by holding both home and volDown keys.
anyway, this lead me to believe my power button is malfunctioning, yet i can still normally press it (Clicking as usual, as if there is no physical damage) and I did not drop or damage my phone in any way.
all of the online threads are regarding phones stuck on boot animation, yet mine is flashing the "Samsung Galaxy S4 GT-I9500" white over black screen (before the boot animation) and doesnt reach boot animation.
i want to believe my data is still reachable as i have not made any backups lately, this is why I came here.
if anyone has encountered any similar issue, please shed some light as this is the first time i had been unable to solve a "boot loop".
thanks in advance!
(ps, phone is still stuck on the loop, i let it keep doing so overnight to let the battery die, plugged it back in to no avail)
Click to expand...
Click to collapse
Hi mate
I sounds a lot like a power button problem , symptoms are similar to other cases , even if power button clicks does not mean is working .... take it to a local service center a have it replace.
Data should be fine.
MAX 404 said:
Hi mate
I sounds a lot like a power button problem , symptoms are similar to other cases , even if power button clicks does not mean is working .... take it to a local service center a have it replace.
Data should be fine.
Click to expand...
Click to collapse
will do. ill update as soon as they return my phone
rdordo23 said:
will do. ill update as soon as they return my phone
Click to expand...
Click to collapse
Great mate.
Good luck
My GT-i9500 just started this same issue less than an hour ago.
I have taken the battery out and I am hoping this will help. Since I never turn the phone off the power button doesn't get used that much. At the most it might get used once a month.
Well I am not sure if this was the reason for it working but I put the battery back in and rocked the power button back and forth. Now its booted properly. Will keep and eye on it, just a pity it would give issues a few days before Christmas. Repair centers won't be open until early Jan.
killerbyte said:
My GT-i9500 just started this same issue less than an hour ago.
I have taken the battery out and I am hoping this will help. Since I never turn the phone off the power button doesn't get used that much. At the most it might get used once a month.
Well I am not sure if this was the reason for it working but I put the battery back in and rocked the power button back and forth. Now its booted properly. Will keep and eye on it, just a pity it would give issues a few days before Christmas. Repair centers won't be open until early Jan.
Click to expand...
Click to collapse
While waiting for the lab to open (sunday) i started flicking my phone a little more violently (upon the acceptable amount of strength), and now i made it boot (!!!).
the current status is the power button is not working, i am carefully navigating to titanium backup... hope i can get a Nand backup aswell, but that's just being greedy. thank god for Philz touch recovery (no power no love on recovery)
Hello mate...
I am using same I9500...i faced same problem wayback in august...phone ws starting indefinitely without even pressing power button. ..so i searched net..
No recovery mode ws accessible to me...couldn't flash....
So i went to Samsung care..
They told i will have to change my PBA meaning passive board assembly. .
Had no other options. .
Spent 9600 on my i9500.
... :/
Sent from my GT-I9500 using XDA Free mobile app
it was working and suddenly it just died ive tried charging it and ive tried pressing power and power + volumen up and down and nothing seems to work. Any thoughts, ideas? the back cover is stuck in a notification it doesnt work also it seems to charge on the Wireless charger
luisumf said:
it was working and suddenly it just died ive tried charging it and ive tried pressing power and power + volumen up and down and nothing seems to work. Any thoughts, ideas? the back cover is stuck in a notification it doesnt work also it seems to charge on the Wireless charger
Click to expand...
Click to collapse
Try to get into download mode. Or wait a while
Sent from my YD201 using Tapatalk
luisumf said:
it was working and suddenly it just died ive tried charging it and ive tried pressing power and power + volumen up and down and nothing seems to work. Any thoughts, ideas? the back cover is stuck in a notification it doesnt work also it seems to charge on the Wireless charger
Click to expand...
Click to collapse
Try pressing power for about 15 seconds, it should reset then.
SteadyQuad said:
Try pressing power for about 15 seconds, it should reset then.
Click to expand...
Click to collapse
it doesnt reset the power button is useless, i guess ill have to wait for the battery to drain maybe then it restarts
adamo86 said:
Try to get into download mode. Or wait a while
Sent from my YD201 using Tapatalk
Click to expand...
Click to collapse
how do i get it in download mode?
luisumf said:
how do i get it in download mode?
Click to expand...
Click to collapse
The easiest way is plugging the usb cable (which is connected to your computer) to your phone while holding volume down button. No need to press power button. From download mode you can boot to recovery etc with the help of your pc.
Jeopardy said:
The easiest way is plugging the usb cable (which is connected to your computer) to your phone while holding volume down button. No need to press power button. From download mode you can boot to recovery etc with the help of your pc.
Click to expand...
Click to collapse
did not work
This sounds more and more like a case for Yota's repair center. If there wasn't something broken in the device one of these methods described in this thread should have worked.
Sounds like hardware to me.
I had the same issue. Left it on the table with the e-ink screen on top, came back hours later, the clock was 90 minutes behind and the phone dead. Resetting with 10 Seconds ON/OFF button didn´t work. Had to send it in. 2 weeks later got it back. They said they had to change the whole motherboard, even got a new IMEI with it. Then a few days later I tried the main camera and it did not work, error message by Android, unaccessible camera... Then by pressure on the camera it worked sometimes, sometimes only misty lines, sometimes splitscreen mode, sometimes not. Maybe a mistake by the service while reassembling the phone? Anyway, had to send it in AGAIN, got it back, sold it on ebay with 130 Euros loss and bought a new white one because I love the principle and options of the second screen so much. The white one is a newer batch, they say with some new (and probably more reliable?) hardware, so up until now I am completely satisfied, no error for 6 weeks (fingers crossed...)
My old black one was maybe a monday batch
petra333 said:
I had the same issue. Left it on the table with the e-ink screen on top, came back hours later, the clock was 90 minutes behind and the phone dead. Resetting with 10 Seconds ON/OFF button didn´t work. Had to send it in. 2 weeks later got it back. They said they had to change the whole motherboard, even got a new IMEI with it. Then a few days later I tried the main camera and it did not work, error message by Android, unaccessible camera... Then by pressure on the camera it worked sometimes, sometimes only misty lines, sometimes splitscreen mode, sometimes not. Maybe a mistake by the service while reassembling the phone? Anyway, had to send it in AGAIN, got it back, sold it on ebay with 130 Euros loss and bought a new white one because I love the principle and options of the second screen so much. The white one is a newer batch, they say with some new (and probably more reliable?) hardware, so up until now I am completely satisfied, no error for 6 weeks (fingers crossed...)
My old black one was maybe a monday batch
Click to expand...
Click to collapse
Hi Petra. Since you're using a Yotaphone as well, could I ask you to do a small favour for me please? After I had my YP rooted I accidentally deleted the system app "back screen manager". My back screen has stopped working since then. It'd be fantastic if you could just extract the system app from your phone and send it to me so that I can manually place the system app on my phone root folder. You don't have to root your phone for this. All you need is an App extractor from play store. And it will take less than 5 mins to extract and send it to me(Assuming that you are well versed with android OS). Here's my email address [email protected] or you could send me a link to the shared file. Do let me know if you are willing or not. Thanks a ton.
So a couple weeks ago my Nexus 6P died.
I had just taken it off charge and it froze then just died. Became unresponsive and I can't boot it or boot it into recovery. So I have a paper weight at the moment.
Ever since, there has been a couple instances where I got the phone to boot into the Google logo and it will freeze there. Either that, or it will get into the loading animation and freeze on that. It will not turn off until I turn it off myself.
I've only been able to do this a couple times with it being on charge for an hour, unplugging it and plugging it back in whilst holding the power button. Trying to get into recovery with this method has proven unsuccessful.
When left until there is no charge on the phone, I am able to invoke the red blinking lights on the notification led by holding down the power button in any variation (e.g. vol down + power, vol up + power, etc)
The question is if anyone else has come across this issue before and if there is any fix?
I do not believe this is BLOD. Maybe fried mobo or maybe battery is bad.
I can't RMA the device back to Google as I bought the phone whilst I was working in Japan and I bought it from Google Japan and I am know back in the UK.
So they apparently follow local warranty. I've spoken to them about 3 times about this and refuse to budge. Huawei are also no help as I bought the device from overseas, they said they aren't allowed to send any devices from Asia to their UK service centre.
So I'm kinda stuck. Any help would be greatly appreciated.
CookieDude_2332 said:
So a couple weeks ago my Nexus 6P died.
I had just taken it off charge and it froze then just died. Became unresponsive and I can't boot it or boot it into recovery. So I have a paper weight at the moment.
Ever since, there has been a couple instances where I got the phone to boot into the Google logo and it will freeze there. Either that, or it will get into the loading animation and freeze on that. It will not turn off until I turn it off myself.
I've only been able to do this a couple times with it being on charge for an hour, unplugging it and plugging it back in whilst holding the power button. Trying to get into recovery with this method has proven unsuccessful.
When left until there is no charge on the phone, I am able to invoke the red blinking lights on the notification led by holding down the power button in any variation (e.g. vol down + power, vol up + power, etc)
The question is if anyone else has come across this issue before and if there is any fix?
I do not believe this is BLOD. Maybe fried mobo or maybe battery is bad.
I can't RMA the device back to Google as I bought the phone whilst I was working in Japan and I bought it from Google Japan and I am know back in the UK.
So they apparently follow local warranty. I've spoken to them about 3 times about this and refuse to budge. Huawei are also no help as I bought the device from overseas, they said they aren't allowed to send any devices from Asia to their UK service centre.
So I'm kinda stuck. Any help would be greatly appreciated.
Click to expand...
Click to collapse
Some more information would be useful like do you have an unlocked bootloader and have debugging enabled?
DEVILOPS 007 said:
Some more information would be useful like do you have an unlocked bootloader and have debugging enabled?
Click to expand...
Click to collapse
Unfortunately I don't have the bootloader unlocked nor have I got debugging enabled (I don't think).
Its pretty much as it was outta the box. Only things I tinkered with was enabling dev options in the settings but that is as much as I've done really. But haven't messed around with any of those settings.
The device is all stock.
CookieDude_2332 said:
Unfortunately I don't have the bootloader unlocked nor have I got debugging enabled (I don't think).
Its pretty much as it was outta the box. Only things I tinkered with was enabling dev options in the settings but that is as much as I've done really. But haven't messed around with any of those settings.
The device is all stock.
Click to expand...
Click to collapse
Did you enable OEM unlocking if you enabled Dev options?
DEVILOPS 007 said:
Did you enable OEM unlocking if you enabled Dev options?
Click to expand...
Click to collapse
I don't think so. Sorry, I'm not super technical.
Not wanting to make a new thread when this seems to be relevant; I appear to be experiencing the same issues as the OP.
I was at work and I noticed that my phone had switched off. I assumed it had ran flat and I hadn't noticed so plugged it in when I got home to no avail. The following day I was playing with the power button; holding it down for a period and pressing thinking it might be a loose connection and eventually it did turn back on but only for a few hours and since then the only response I get is a red LED when pressing the power/volume button whilst on charge.
I have replaced both the battery and the charging port/daughter board but this does not appear to have resolved the issue. Is there something I am missing or is my phone now a very expensive paperweight? If that is the case this will be the second Nexus device I owned which died in similar circumstances not long out of it warranty; I had a Nexus 6 which died after a year which I replaced with the 6P and it may be that the same thing has happened.
Any help, advice or suggestions anyone can give would be much appreciated!
Edit: Answering a question asked previously with regards to more information my bootloader is unlocked however I can't remember if USB debugging was enabled. I have a feeling that it is disabled as a work around for Magisk Hide and passing SafetyNet.
CookieDude_2332 said:
I do not believe this is BLOD. Maybe fried mobo or maybe battery is bad..
Click to expand...
Click to collapse
BLOD is a bad motherboard. If you can't access Recovery and are bootloader locked, you're at the end of the road.
Have you tried to keep it plugged in then hold the volume down button and power button at the same time, and hold it hard for a while and see if it goes to the recovery partition.
Otherwise, why don't you bring to a hardware store and talk to someone?
GLHF!:crying:
So I've spoken to Huawei on a whim and found out that my phone is under warranty so I am waiting on a return delivery envelope to go to one of their Service Centres however I would like to at least try to restore back to stock and re-lock the boot loader as I have managed on a few occasions to get the phone to boot to the 'Google' logo before it would then shut down. I have since plugged the phone in to my laptop and "QHSUSB__BULK" appears in Device Manager.
I have Wugfresh's NRT 2.1.9 but this does not pick up fastboot or adb. Is there any other tool I should be aware of or a driver I haven't got installed? Is this something anyone has come across or managed to resolve before?
beejkitsune said:
So I've spoken to Huawei on a whim and found out that my phone is under warranty so I am waiting on a return delivery envelope to go to one of their Service Centres however I would like to at least try to restore back to stock and re-lock the boot loader as I have managed on a few occasions to get the phone to boot to the 'Google' logo before it would then shut down. I have since plugged the phone in to my laptop and "QHSUSB__BULK" appears in Device Manager.
I have Wugfresh's NRT 2.1.9 but this does not pick up fastboot or adb. Is there any other tool I should be aware of or a driver I haven't got installed? Is this something anyone has come across or managed to resolve before?
Click to expand...
Click to collapse
Leave it just the way it is. You're stuck in QC 9008 diagnostic mode. Perfect for sending the phone back. Don't worry about it.
v12xke said:
Leave it just the way it is. You're stuck in QC 9008 diagnostic mode. Perfect for sending the phone back. Don't worry about it.
Click to expand...
Click to collapse
Thanks for the advice. I'm just waiting on them sending me the jiffy bag to send my device out to them.
I'm not holding my breath on them actually fixing or replacing it as I have done a DIY battery replacement a little while ago (though I did replace with an OEM battery) but I figure it's worth a shot and worst case scenario I'll hold out for Oct 4th and hope the Pixel 2 XL rumours are right and it will have a similar screen design to the Galaxy S8+.
I love the look of the Infinity Display but will not have a Samsung.
beejkitsune said:
...I love the look of the Infinity Display but will not have a Samsung.
Click to expand...
Click to collapse
Totally agree.
beejkitsune said:
Thanks for the advice. I'm just waiting on them sending me the jiffy bag to send my device out to them.
I'm not holding my breath on them actually fixing or replacing it as I have done a DIY battery replacement a little while ago (though I did replace with an OEM battery) but I figure it's worth a shot and worst case scenario I'll hold out for Oct 4th and hope the Pixel 2 XL rumours are right and it will have a similar screen design to the Galaxy S8+.
I love the look of the Infinity Display but will not have a Samsung.
Click to expand...
Click to collapse
Final update. Apparently Huawei are struggling with a parts shortage and don't know when parts will be come available so they have offered me a "Limited Edition" Gold Mate 9. I'm not entirely happy about this arrangement as I really loved my 6P but they have had my 6P for about six weeks and I haven't had a fully working phone since August 18th so I'm left with little other choice since I can't afford the P2XL.
Thanks for your help and in general to everyone in the 6P threads who have helped me out of the past 18 months.
My screen broke 6 months ago, so it wasn't used/charged for 6 months. Now I've replaced the screen, but it won't start up anymore. First thing I saw was the warning "low battery", so I charged it for a while. Still, nothing. Charged it for several days, nothing. Checked the battery voltage, 3.80 volts, exactly what it should be I think?
The phone does do something though. When I hold the "on" button, after 5 seconds it buzzes and the screen shows the oneplus logo and android. Just for two seconds, then nothing. Same thing with "on" and volume down, the start-up screen for 2 seconds...
When I use "on" and volume up, I get the screen saying "fastboot mode". And that doesn't go away untill I press "on" for a while.
I can connect it to my laptop, but cant see it. But when I take the battery out while connected to the laptop, the phone will show the "low battery" warning. Connect the battery again, and the logo and android message come on for two seconds...nothing more.
So the screen works, the battery is charged, but no way to turn it on. Tried holding the "on" button for 15 seconds, same result. Just a 2 seconds oneplus logo visible...
I have no clue what this could be, I hope its not completely fubar...
Thanks in advance, Fred Doe
Hey Fred Doe,
I wouldn't like to hijack your post, but I seem to have run into the exact same issue here.
A friend of mine got his screen replaced, and the phone acts exactly the same as yours.
I have disassembled the phone and checked all connections, but everything seems to be correct on the inside.
The phone does seem to boot, and it does boot into recovery mode (it responds to the button presses by vibrating) but the screen just doesn't show anything.
Only when doing fastboot the screen stays on.
Hopefully someone here can point us in the right direction.
there's not much to hijack here...sure sounds like the same problem. At this moment I gave up, guess its a lost cause..
Guys, the exactly same thing here. I've tried to unbrick it but failed.... So far what I know is that bootloader is locked.
I would like to know what steps should us do in order unlock bootloader, get screen functioning while getting access back to bootloder (TWRP) so after that we can install a new ROM!
Any clue from the community of OnePlus 2? This phone is still a good phone! Thnx
Have you guys tried running the msm tool. It'll restore everything to stock if you can it to work. If either of you have magisk installed it can cause issues with charging while the phone is off I believe.
I mean honestly sounds more like hardware issue that a msm wouldn't fix, but it's weird that your screen works in fastboot.
If you do the msm tool though be aware it will wipe everything on your device, and relock the bootloader if it is unlocked.
Like I said doubt it will help, but just a thought.
Edit: Also make sure you use the correct one for your device.
Edit sorry guys wrong forum ignore everything I said. Apparently xda labs thought my OP6T was a OP2.
Sent from my ONEPLUS A6013 using XDA Labs
@TheLogicalGamer
no problem. Thnx anyway. I'm still locked with my OP2.
dajosova said:
@TheLogicalGamer
no problem. Thnx anyway. I'm still locked with my OP2.
Click to expand...
Click to collapse
But the screen does show up & stays on in fastboot?
I'm no expert but any stretch. I just jumped ship from lg my 6t is the 1st OP phone I've owned. But if the screen does work normally in fastboot then it wouldn't be illogical to entertain the idea that it was a software issue. So I mean this is a bit of a chin scratcher.
Sent from my ONEPLUS A6013 using XDA Labs
Thanks for replying.
IWhen I press Power + Vol. Up it shoes Fast Boot screen. Then I connect cable and sometimes I can use command line but can't unlock bootloader with command line. All methods found indicate to use Recovery but since my screen doesn't work on Recovery I'm stuck.
When I press Power + Vol. Down (for entering Recovery) screen it goes all black but the capacitive buttons and Volume button give back a vibration response, as if it have entered Recovery Mode but since I can't see nothing on screen I can do anything either.
My bootloader is locked because I see that info via command line.
Thanks anyway
PS: I think something is corrupted. My OP2 was unlocked much time ago. I frquently change ROM's and have also updated TWRP. The only thing I did was disassembling the phone in order to change a shattered screen glass.
I've also tried different methods and installed in my pc different Qualcomm drivers, ADB, etc.
I'm getting close to the point of testing with broken touch, buying a new touch screen but with frame or giving up completely and buy a new phone :|
The last option get me in doubt because I would like a phone wich is good and fast and decent battery but not with a premium price... and popular so I can unlock it without hassle in order to install root apk's.
I am unable to boot up the device. I tried all (power + Vol Up) key combos, not working. Is there anyway to pull data out from the device?
easyxpress said:
I am unable to boot up the device. I tried all (power + Vol Up) key combos, not working. Is there anyway to pull data out from the device?
Click to expand...
Click to collapse
No fastboot or custom recovery ?
Then no theirs nothing really to do
Maybe a battery replacement would boot it up
Sent from my ONEPLUS A6010 using Tapatalk
No fastboot or custom recovery. I'm wondering if the *storage* can be pulled out like a hard drive?
easyxpress said:
No fastboot or custom recovery. I'm wondering if the *storage* can be pulled out like a hard drive?
Click to expand...
Click to collapse
Nope it's just a chip on a circuit board
Sent from my ONEPLUS A6010 using Tapatalk
easyxpress said:
I am unable to boot up the device. I tried all (power + Vol Up) key combos, not working. Is there anyway to pull data out from the device?
Click to expand...
Click to collapse
Not enough information. What did you do prior to your phone failing to boot? Was there a software mod you installed? What were the symptoms the phone showed the last time it was on? Any problems before it failed to boot like an old battery, misbehaving ROM, poor charging?
Basically, you need to identify (help us identify) the cause of your phone not booting. We cannot find the solution to a problem we don't know the cause of. The problem must first be defined and then we work from there.
All the best.
twistyplain said:
Not enough information. What did you do prior to your phone failing to boot? Was there a software mod you installed? What were the symptoms the phone showed the last time it was on? Any problems before it failed to boot like an old battery, misbehaving ROM, poor charging?
Basically, you need to identify (help us identify) the cause of your phone not booting. We cannot find the solution to a problem we don't know the cause of. The problem must first be defined and then we work from there.
All the best.
Click to expand...
Click to collapse
Prior to the phone failing to boot, the phone kept crashing. I saw the screen turning into *mess* and then the phone shut off by itself. Initially, I was able to boot up the phone after the crash, however the screen would get mess up and shut off again after a few minutes. Eventually, It got harder and harder to turn on the phone until it finally failed to boot (die). At this point, the phone seems dead. When I plug in the charger, there is no response of any kind, just black screen.
At one time, when the phone was on its last legs, I was able to boot into the Recovery mode, the phone seems to stay in that mode without the crash. Unfortunately, I didn't stay long enough in the Recovery mode to confirm this.
The phone was running on Lineage of Android 8. I have been using the phone for two years, the battery is surely weakened but can still last an hour or two for continual Youtube watching. I didn't do any software update after the Lineage Android 8's last nightly build.
Hope you can help and give some pointers. Thanks.
-- Joseph
easyxpress said:
Prior to the phone failing to boot, the phone kept crashing. I saw the screen turning into *mess* and then the phone shut off by itself. Initially, I was able to boot up the phone after the crash, however the screen would get mess up and shut off again after a few minutes. Eventually, It got harder and harder to turn on the phone until it finally failed to boot (die). At this point, the phone seems dead. When I plug in the charger, there is no response of any kind, just black screen.
At one time, when the phone was on its last legs, I was able to boot into the Recovery mode, the phone seems to stay in that mode without the crash. Unfortunately, I didn't stay long enough in the Recovery mode to confirm this.
The phone was running on Lineage of Android 8. I have been using the phone for two years, the battery is surely weakened but can still last an hour or two for continual Youtube watching. I didn't do any software update after the Lineage Android 8's last nightly build.
Hope you can help and give some pointers. Thanks.
-- Joseph
Click to expand...
Click to collapse
This appears to be hardware failure. The SoC is most probably dead. You should have recovered your data when it was still able to boot. Right now I think it's too late.
twistyplain said:
This appears to be hardware failure. The SoC is most probably dead. You should have recovered your data when it was still able to boot. Right now I think it's too late.
Click to expand...
Click to collapse
I just plugged in the phone. Miraculously, after few minutes, it did come up with the boot screen (with some messy lines), see the attached picture. However, It didn't go beyond the boot screen and recycle again for 2 or 3 times and then no more. I was able to duplicate this recycling situation several times after plugging it to the charger. Also, I was able to push it into the Recovery mode, but it only stay at the boot screen (with lines) and shut off again after few seconds.
What do the messy lines on the boot screen suggest? Is it the battery totally dead? Or, is the charging system faulty that somehow it doesn't have any enough juice to push thru beyond the boot screen and hence shut off?
-- Joseph
easyxpress said:
I just plugged in the phone. Miraculously, after few minutes, it did come up with the boot screen (with some messy lines), see the attached picture. However, It didn't go beyond the boot screen and recycle again for 2 or 3 times and then no more. I was able to duplicate this recycling situation several times after plugging it to the charger. Also, I was able to push it into the Recovery mode, but it only stay at the boot screen (with lines) and shut off again after few seconds.
What do the messy lines on the boot screen suggest? Is it the battery totally dead? Or, is the charging system faulty that somehow it doesn't have any enough juice to push thru beyond the boot screen and hence shut off?
-- Joseph
Click to expand...
Click to collapse
what happened to TWRP ? thats stock recovery
will it enter fastboot mode ? if you can get into TWRP their is a chance of off loading your userdata to a PC
easyxpress said:
I just plugged in the phone. Miraculously, after few minutes, it did come up with the boot screen (with some messy lines), see the attached picture. However, It didn't go beyond the boot screen and recycle again for 2 or 3 times and then no more. I was able to duplicate this recycling situation several times after plugging it to the charger. Also, I was able to push it into the Recovery mode, but it only stay at the boot screen (with lines) and shut off again after few seconds.
What do the messy lines on the boot screen suggest? Is it the battery totally dead? Or, is the charging system faulty that somehow it doesn't have any enough juice to push thru beyond the boot screen and hence shut off?
-- Joseph
Click to expand...
Click to collapse
Yup...This phone is dead. I have seen a similar le pro 3 posted here on XDA with the same streaks along the display. It's definitely a hard brick. No way to get around it that I know of. I'd like to rope @tsongming in on this. He has seen a few dead pro 3's so this is within his expertise.
Sent from my LeMobile Le X526 using XDA Labs
twistyplain said:
Yup...This phone is dead. I have seen a similar le pro 3 posted here on XDA with the same streaks along the display. It's definitely a hard brick. No way to get around it that I know of. I'd like to rope @tsongming in on this. He has seen a few dead pro 3's so this is within his expertise.
Click to expand...
Click to collapse
Sorry bad news.
As twistyplain said, your phone is absolutely fried, and there is no solution.
It's definitely no brick, that is a hardware issue... Most likely shorted solder connections. The same thing happened to two of our X727s, we have one left that still works.
I highly recommend buying a seemingly unbrickable Xiaomi phone. Their budget models are awesome and of course their flagships are awesome. Everyone in my family has Migrated to Xiaomi . I currently have Android 10 working flawlessly.
Thanks for the info. I made a mistake of not backing up the photos from the phone. I'm still hoping for a slim chance and searching that some of the repair shops (in China?) are somehow able to boot up the phone and retrieve the photos for me. Meanwhile, I'll check into Xiaomi.
-- Joseph
easyxpress said:
Thanks for the info. I made a mistake of not backing up the photos from the phone. I'm still hoping for a slim chance and searching that some of the repair shops (in China?) are somehow able to boot up the phone and retrieve the photos for me. Meanwhile, I'll check into Xiaomi.
-- Joseph
Click to expand...
Click to collapse
If you are in China and located in a large city or tech industrial area you should have plenty of shops that repair at the component level.
Your phone could very likely be repaired by a shop that has a hot air rework soldering station with an electron microscope.
We used to have these types of places in the US but they have all gone out business, replaced by board swappers, who charge a lot. I would suspect that you could get it repaired in China for 100 yuan or less.
I worked in Beijing for 3 months, about 18 years ago and these types of places were everywhere.