Related
Hey guys,
The earpiece speaker on my G1 has developed a fault, the fault being it doesn't appear to work, how easy is it to source a replacement for it and how easy is the repair itself? is there any guides as to how to do it around? (i looked but i couldn't find anything).
I've tried flashing the rom and doing a hard reset but its still faulty.
The loud speakers working fine though so atm all my calls have to be done on the handsfree kit or via loudspeaker which can get annoying.
any help is much appreciated
regards
Streather
Are you using a ROM where sound works?
What ROM are you using?
Tried it with cynagen and the stock tmob one, same results.
Same problem
I'm using CyanogenMod 4.2.5. I dropped the phone about a foot (it fell out of my shirt pocket as I was tying my shoe!), and the earpiece stopped working. Everything else (speaker phone, etc.) works fine.
I've seen a number of similar cases in other forums, so I'm thinking that this is a weak point. I'll attempt disassembly and see if the speaker contacts got moved or something simple. Fortunately, replacement receivers/earpiece/speakers are available over the net.
Meanwhile, I'd love to learn of others' experience with this. The tech manual makes it look like you have to just about completely disassemble the phone to get at the earpiece, even though you can easily access 3 screws on the back of the lcd. Is there a shorter route to the receiver than a complete disassembly?
[update] I found some good info (including a technical manual) by Googling "g1 phone disassembly". And searching for "g1 speaker" on eBay gave some decent looking results.
[update 2] I disassembled my phone, took out the receiver, cleaned its contacts, replaced it, and and reassembled everything. That was a pretty serious chore, and it demonstrated that a nearly complete disassembly is required to access the receiver (yes, including all the stuff at the opposite end of the phone). I don't know how to test the receiver without being in cell range, which my house is not. But at least nearly everything else still works, except the camera--I need to tear back into the phone and make sure I fully seated the FPC. I think finding a replacement receiver will be a challenge--most of what turned up on eBay is actually the main speaker on the back of the phone, and I have yet to find a vendor that sells receivers.
Sadly, you will almost have to tear down the whole unit to get to it. It's not extremly diffucult, but you will need to be steady and gentle. Good luck.
Success!
I haven't seen many report back after tearing apart their phones to address issues with a bad receiver, so here goes. My simple-minded approach of opening it up, cleaning the receiver contacts with a pencil eraser, and ensuring good alignment before reassembling WORKED. I did not have to buy a new receiver.
Now if I can just get my camera to work again (I think I didn't get the cable well seated).
[update]: camera works! Seating that FPC took some nimble fingers--I got it on the 3rd attempt. I hope this proves useful to others who, like me, do not have the warranty option for various reasons.
I dropped my phone once, by accident, same thing happened. The speaker you use to put your ear up to when making a phone call doesn't work, but the speaker phone speaker works as does a bluetooth headset. Called HTC lied said that it just stopped working out of no where, they said its covered under warranty. Luckily the phone is under warranty until March and will be replaced.
I ran into the same problem. I was having intermittent problems with the earpiece. Yesterday I was able to take out the battery and put it in and it started working again. Today that didn't help either. I saw this thread and I thought that I'd try blowing really hard on the earpiece to see if that helps. It seems to be working again! I hope it continues to work.
dirtprof said:
Now if I can just get my camera to work again (I think I didn't get the cable well seated).
[update]: camera works! Seating that FPC took some nimble fingers--I got it on the 3rd attempt. I hope this proves useful to others who, like me, do not have the warranty option for various reasons.
Click to expand...
Click to collapse
Can you post details on how to do this?
My camera stopped working too.
I personally found it easier when disassembling the phone to carefully lift the entire camera and IMEI sticker as a whole unit and remove it as part of the motherboard. That way you dont need to mess with that hard to reach connector. So from where you are at, lift the board back out, reattach the camera assembly, and reassemble as a unit. I think you will find it is MUCH easier
Seat the camera FPC fully
RueTheDay said:
Can you post details on how to do this?
My camera stopped working too.
Click to expand...
Click to collapse
I had to lift the motherboard up and away from the hook that held it down in order for the FPC clip to open fully. Then I inserted the FPC *fully* before closing the FPC clip (my failures resulted from not being able to fully seat the FPC because the FPC clip could not fully open as long as the motherboard was in place). Then the trick was to get the motherboard back under its hook without accidentally pulling the FPC back out again. What I did was to press it gently straight down, using my fingernail to ease it past the hook.
Good luck!
bump...
Yeah looks like all there is on Ebay for speakers is the back one, the one for the receiver earpiece looks like it has two wire connections at each end while the one for the back speaker has them right next to eachother.
So if anybody had this problem, it is very odd and might have to do with the spring connection maybe.
Still I had this problem before and it fixed itself randomly, but this problem came out of nowhere because 12 hours earlier I had dropped my phone on its back and it continued to work fine. Than on my way driving randomly it would not work and I barely set it down in my car.
Once again hopefully somebody has found a part for this because ebay only has back speaker parts.
Best bet is to blow on it and massage it or tap it until it works, damn this sucks because it is basically the very last step to get to after dissambling your phone. So much work to get to such a common problem for many people.
I almost wanted to try to shortcut it and undo the two screws on the screen section to move it around to make connection. Now I am the deusche bag with the bluetooth in his ear all the time.
I almost wanted to try to shortcut it and undo the two screws on the screen section to move it around to make connection.
Click to expand...
Click to collapse
That was what I tried at first. It didn't gain me access to the speaker.
Taking the phone apart is a pain. You really need nimble fingers and faith that you're not breaking the phone when you're levering apart the *very* tightly held together plastic parts. HTC did not make this thing with servicing it in mind. Just be sure to have the right tools (including light and a good magnifying glass if you're over 40) and patience.
Removing the 3 screws that are accessible without disassembling the entire phone will get you in there if you are VERY careful. Unfortunately the one I tried this on did not work differently with a known-good speaker in it. You can delicately dig out the old speaker with a knife (Xacto) and drop the new one in. Takes patients, but not nearly as hard as disassembling the entire phone (been there, done that x10)
I have at least one spare speaker. Maybe more, gotta check my stockpile!
Hey,
My phone got dropped in a rum & coke on Saturday, so i soaked it in 90% rubbing alcohol and let it dry in a rice bath. after 4 days in the rice, it looked dry, so i turned it on. IT WORKS! The screen looks a little trippy (the pattern is even changing throughout the day) but the touch and accelerometer work great. The only real problem is the speakers sound like crap. the receiver is so quiet that it sound like they're wispering, and the back speaker is all crackely.
I found a replacement receiver speaker, but as i haven't taken it apart yet, i was hoping one of you could tell me if this looks correct.
http://www.tvc-mall.com/details/Replacement-Speaker-Earpiece-Receiver-for-HTC-G1-HTCO-G1/photos.htm
If so, i guess i'll order both speakers and attempt to replace them.
That looks about right. Bear in mind, of course, that those pictures are greatly magnified. If you haven't taken apart a G1 yet, you're in for a bit of nerve-wracking prying. Just go slowly and be patient. Getting all the way to the receiver speaker means taking the phone most of the way apart.
Thanks!
I have taken apart a phone before, the Dash (excalibur). I had to replace the screen, it involved removing almost every component.
I think i'll go ahead and order it, and cross my fingers. right now the phone isn't much more then a tiny computer, since i can't hear anyone and i don't have a Bluetooth.
Hello Guys,
I just got my HD2 from repare, had to change the screen since it became unresponsive.
After I got it back, installed both WP7 and Anrdoid on it, I found out that the phone is not detecting any wifi networks. I tried in both WP7 and Android, and both of them do not detect any wifi networks. So it looks like when they changed the screen, they messed up WIFI connectivity. I'm guessing they might have forgotten to connect one of the connectors.
I am planning to take it back to them, but I was wondering if any of you knows which connector is for the WIFI, and if its easily visible once I take the back cover off, since I already done that before.
Thanks in advance
Hi dude,
if a connection is a problem and you even going to find it don't do it yourself.
it's a pretty small and gentle stuff, so you must know what you doing and how to connect them. Obviously you will need some serious tools.
my guess if you had all that - you already been doing this and not asking here.
so advice - not touching anything, not making it worse.
Best case: the connector came loose (which is not all that uncommon). It's the connector on the black wire on the top right side of the main board.
Worst case, they broke off a contact (which is also quite common).
Either way, don't try to repair it yourself but bring it back to the repair shop. If they accidentally broke off a contact then that requires a professional repair.
Thanks guys.
After some tests, I found out that the phone does detect wifi networks, but have extremely bad reception. I have to be very close to the wifi router for it to detect the network.
Any idea what might be causing this?
wessamzeidan said:
Thanks guys.
Any idea what might be causing this?
Click to expand...
Click to collapse
Like I said, either a loose connector or a contact has broken off. That will give you about 1 bar of reception while sitting next to your router...
Hi,
So long story short...I need to replace the Ear Speaker Flex Cable Ribbon with Sensor Part. My phone is not covered by warranty and I really need it to be working, I rely on it heavily for music and as it stands...the headphone jack no longer works properly. Only one of the earbuds work at a time, unless I spend a minute trying to wiggle it and hold it in place which is obviously not convenient. And it's not the headphones..tried many pairs and even tried plugging it to a set of speakers with the same result.
Any recommendations or anyone know of a site where I can purchase this part?? Any help would be immensely appreciated, I don't know how soon I'll be able to make the switch to the HTC Titan
A quick search reveals on eBay this and some other places, like globaldirectparts, mptgsm, oemcellphoneparts etc. (I used this search) but fortunately I didn't need any so I can't tell you about the service. For sure there are others.
EnderPsp said:
A quick search reveals on eBay this and some other places, like globaldirectparts, mptgsm, oemcellphoneparts etc. (I used this search) but fortunately I didn't need any so I can't tell you about the service. For sure there are others.
Click to expand...
Click to collapse
Exactly what I needed in eBay, I didn't think to look there. I had checked the globaldirect but they don't sell to consumers.
abenitez64 said:
Exactly what I needed in eBay, I didn't think to look there. I had checked the globaldirect but they don't sell to consumers.
Click to expand...
Click to collapse
Good luck, I hope you get this sorted right! I believe there are several videos on how to take apart the Focus on youtube that you might find handy. Please post here details about your success story, afterwards: time, tools etc
OK, after being so annoyed with the Navigation on this phone not working, I finally found a fix that is working for me and I am in shock that what I did produced a working GPS. First, anyone who doesn't know how to take apart the black cover (not the battery cover) do a search. Next, after removing the cover, the GPS Antenna without a doubt is one right next to the power button. I found this out by putting a piece of electrical tape over every gold connector that touches an antenna, then closing the black cover, turning on the phone, running gps test, and after trying different spring connectors, I noticed I had the correct one when the app GPS Test couldn't locate any satellites. Next, I also noticed that on the inside of the cover that I took off, the one that requires six screws, there is a silver looking strip that is supposed to make contact to the connector that has a full metal top part, so when the cover goes back on, the silver strip must make contact to this negative grounding harness top. I added a bead of solder to the silver strip on the inside of the black cover so that I knew it was making contact. I believe that this is a source of everyone's problems with navigation. That strip must be a shield and the design doesn't look like it makes good contact to the connector's ground metal plate. You'll see what I mean when you open the cover.
Next, while I had the cover off, I wrapped a 30 gauge wire around the gold spring pin that connects to the GPS antenna and ran that wire down the side of the phone right along the PC Board in hopes that it extends the antenna. I just ran it like 3 inches and remember, I ran it down, not up. The GPS antenna already goes up. I put a tiny bead of solder on the wire where it contact the gold spring contact that is attached to the PC Board so that it does not come off accidentally. And believe me, it is really simple. You cannot mess anything up. Just a dab of solder is all it takes.
I put the black cover back on, and then ran the GPS test app and at one point I had 12 satellites read and used with a 7 foot accuracy!!! Next I went to the Navigation app and started playing around with different addresses and my navigation WORKED!!! I am still in awe three days later. I drove from New Jersey to Rhode Island yesterday and had the Nav running for the entire trip. Only one time did I get a small circle about the size of a half inch which lasted for 4 seconds. At that point, I was driving though a forest type side road with limited sky view.
Please try this fix for anyone who has Navigation issues with their Nexus S and let me know if it fixes it.
Dan
Awesome. Samsung should have hired you before they released the Nexus S and 1st-gen SGS phones. My Captivate never had reliable GPS. I might as well have had Ray Charles giving me directions.
Funny thing is Google nexus phones are bugged...
Nexus one multi touch bug
Nexus s compass not working...
I think the issue here is with whoever was choosing and picking the hardware that would have powered a nexus...
HTC and Samsung do not surprise me... But Google not testing the compass on a flagship phone before releasing scares me :-\
Luckily my gps works fine (i9023 here) but the broken compass create a lot of troubles with gps navigation as very often the phone thinks to be driving in the reverse direction...
The nexus one digitizer wasn't a bug. Just a crappy digitizer. It worked as it meant to. It sucked but wasn't a bug.
The GPS and compass issues for the nexus s are different as well. Some devices have crappy ones and apparently don't work. My GPS and compass works perfect on the other hand. Always has
evcz said:
Funny thing is Google nexus phones are bugged...
Nexus one multi touch bug
Nexus s compass not working...
I think the issue here is with whoever was choosing and picking the hardware that would have powered a nexus...
HTC and Samsung do not surprise me... But Google not testing the compass on a flagship phone before releasing scares me :-\
Luckily my gps works fine (i9023 here) but the broken compass create a lot of troubles with gps navigation as very often the phone thinks to be driving in the reverse direction...
Click to expand...
Click to collapse
I don't have problems with navigation, even tho i hardly ever use it. However, this compass thing; I downloaded an app called Smart Compass and it works really well... Where I know it's north, the compass points north and so on. but mind you, I got my phone after companies stopped selling it so I might've gotten the last of the good batch
Could you post a photo of the finished fix so I can check if I'm going to fry something ? Thanks !
@VOLTAGEROCK:
post some photos for better help if it's possible, before and after modifications please
thanks in advance
I will but gimme a day or two. All I know is I'm on day five and its still working!
wow
Sent from my
RESSURECTED Nexus S
CM10 NIGHTIES
DmA81 said:
Could you post a photo of the finished fix so I can check if I'm going to fry something ? Thanks !
Click to expand...
Click to collapse
I should have at the time of doing it, but I didn't know what i was doing was going to work!! Now I have to take the phone apart again, but you give me a reason to hook up my Touchstone from the Pre while the phone is open and accessible. I will do my best to put the pics up in a timely manner and in the meantime, if there's anyone out there, go to the iteardown fix it (i think that's what its called) and look at the video or pics of the Nexus being taken apart.
Again, I have no reason to believe that I didn't fix the problem as it's working everytime, when it wouldn't work at all before the mod. When you're looking at the phone from the back, the GPS antenna location has a letter G engraved into the black cover after the battery cover has been taken off. It's right below the electrical type tape that covers the antenna FYI.
*#*#gpsclrx#*#* always fixed my gps woes and i had a lot. no hardware mod required.
Sputnikk23 said:
*#*#gpsclrx#*#* always fixed my gps woes and i had a lot. no hardware mod required.
Click to expand...
Click to collapse
What does that do by the way.? Because my mod works everytime and you never have to use the code you just put up. Even though I appreciate you putting that there. Also, what type of problems were you having with your navigation? Did it work periodically? Did it never work like mine? Just curious as to the problem you had with your navigation. Thanks
Dan
I can confirm this hardware mod fixed voltages gps. He's gone thru 2 nexus s phones and both GPS would constantly lose the position every few minutes then reacquire, and show a huge circle for his position. Somehow this hardware mod fixes some design issue with the nexus s where a shielding isn't properly grounded. And also he extended the GPS antenna with a wire for good measure.
By the way it was the sprint nexus s 4g he modified.
Please post pictures to go with your narrative. I would like to try this!
O
RogerPodacter said:
I can confirm this hardware mos fixed voltages gps. He's gone thru 2 nexus s phones and both GPS would constantly lose the position every few minutes then reacquire, and show a huge circle for his position. Somehow this hardware mod fixes some design issue with the nexus s where a shielding isn't properly grounded. And also he extended the GPS antenna with a wire for good measure.
By the way it was the sprint nexus s 4g he modified.
Click to expand...
Click to collapse
Thanks for the clarification nation, Podact.
VOLTAGEROCK said:
What does that do by the way.? Because my mod works everytime and you never have to use the code you just put up. Even though I appreciate you putting that there. Also, what type of problems were you having with your navigation? Did it work periodically? Did it never work like mine? Just curious as to the problem you had with your navigation. Thanks
Dan
Click to expand...
Click to collapse
wipe gps data. not the same thing as the gps status wipe (which didn't work for me). try it, doesn't really hurt anything. seems a software code is worth a shot then opening up the phone you know?
Some ROMs it never worked. Other ROMs it was sporadic. When I would get it to work, it always eventually "lost" its ability to lock, etc.
But hey.. if you want to get all hyper-sensitive over your mod.. go for it. Was just throwing another method out there for the faint of heart.
Sputnikk23 said:
wipe gps data. not the same thing as the gps status wipe (which didn't work for me). try it, doesn't really hurt anything. seems a software code is worth a shot then opening up the phone you know?
Some ROMs it never worked. Other ROMs it was sporadic. When I would get it to work, it always eventually "lost" its ability to lock, etc.
But hey.. if you want to get all hyper-sensitive over your mod.. go for it. Was just throwing another method out there for the faint of heart.
Click to expand...
Click to collapse
I am sensitive as I cried at your remark, and then I got really hyper and started running in circles with joy that my nav works. So I guess you're right, I am hypersensitive! Btw, I was being nothing but nice to your reply. Its OK. I forgive you.
Pics requested
Check out the pics. One of them shows some solder on the silver shielding so it makes better contact with the connector when they close back up. The other shows a 30 gauge red wire soldered to the gps pin and running down the phone. Hope this clears up what you guys need to do to get the gps to finally work on this dag gone phone.
.I've been using navigation and never had such a problems.my gps always locking under 10sec and doesn't loosing signal.
Btw i live in UK and using nav in big city.
Do a search for Nexus S 4g on sprint nav problems and you'll see a whole slew of people with problems.
Sent from my Nexus S 4G using xda app-developers app
I just recently replaced a malfunctioning LCD and shattered digitizer for my Glacier. Before I did that, the WIFI worked just fine. No problems at all. But now, the WIFI will turn on, but won't pick up any networks at all. All my other phones pick it up just fine, as well as my laptop. I've tried three different ROMs and I have the same issue with all of them. As far as I know, there weren't any cables that connected the WIFI module to the motherboard or anything else when I took it apart and put it back together. It's just a little piece that snaps into place, right? I'm not sure what's going on with this...
Seriously? Nothing? Every time I post on here, I get ZERO response... What gives? I see everyone else's problems being solved but not mine...
Sorry, there's no help to give. Don't act like you're entitled to something. I hate people like that. If you didn't touch the WiFi module through the screen and tried different roms then it went bonkers and its toast. TF are we supposed to do about that
Sent from my HTC Glacier using xda app-developers app
If you're gonna post on here just to be a douche, you might as well not post at all. It's doing nobody any good.
All drama aside, he is right nothing to be done really. I guess you could open it back up again and risk breaking something more important than the wifi. Something may be put back in wrong or may have got ESD damange. Truth is unless you're just using this phone as a toy/dev/learning device and don't care if it breaks it is not worth the risk to open it back up.
Trying to fix my external speaker - I mess up working wi-fi. In addition, the case crack and camera button is not working. Should take it to repair shop. Too late now. It would be too expensive to fix it. You my still be lucky and shop will fix for few bucks. Lesson learn - do not mess with something that you do not understand( for me).
coax cable issue
there's 3 little coax cables - I've been told the white coax is the wifi but the black one fixed it so maybe they are all involved. In the process of getting to the LCD you went through these 3 cables. In most cases you wouldn't have disconnected them but certainly by accident it will happen. I put mine on 3 times before they stayed. There's quite positive click when connected but even then it may come loose while assembling the rest of the phone. I just finished swapping out my mother board and as perfectly as I could reassemble the phone I apparently lost one of the coax connections = no wifi. Went back in and this time the black cable somehow got caught under the camera board instead of on top and connected. Easy to see why this was missed because it looked connected.. well looked like it belonged where it was (wrong)
Anyway that's my wifi fix story - hope it helps someone