Can't flash any Firmware after installing Factory Binary - Samsung Galaxy S7 Edge Questions and Answers

Hello guys,
I need extremely technical help as no longer know what to do.
I have a*Galaxy*S7*Edge*device, which installed the*rom*Samsung Experience 9.0.
Later I*format data to exfat and it doesn't work. After then I flashed any Nougat Firmware and lost my Imei and Baseband.
Number.
I googled until I came to this tutorial:
http://forum.xda-developers.com/s7-e...ssues-t3379516
I followed all the steps explained, I back up EFS_backup and RADIO_bakcup partitions.
Installed FACTORY BINARY Firmware for G935F, everything went well. After restarted, already had the correct IMEI number but still did not present the S / N.
After all that, i tried to*install*Stock*Firmware*via Odin, from here started the problems that could not solve.
In the first attempt Odin stucked in "System" (also used the PITfile*with the same CSC ... .i do not know if I was right using PIT?). Restarted the*device*forcibly, entered the stock Recovery, did a complete wipe and always get this message "E: falied to*mountSystem*(Invalid argument), I returned to*install*Factory Binary, then reboot in Recovery and the same message no longer appeared.
Again I try to*install*the Stock*Firmware*and Odin always stucks in*System, or NAND writing, or Partition, etc. I've tried various Stock*Firmware, with and without PIT*files, always without success.
Only Factory Binary that successfully installs. The TWRP via Odin also but when*device*restarts to enter Recovery Mode always get the message at the top of the*display:
"Recovery image signature check Fail"
"Reboot to avoid Warranty bit set."
My Question also is: What do I wrong? Or is my Phone bricked?
Device:
Galaxy S7*Edge (SM-G935F) CSC = DBT = Germany
I really need help, please.

I am facing same problem with my s7 edge g935fd. But in my case i lost imei of both sim cards & lost baseband version. I tried z3x samsung tool. But i didn't found model g935fd there.
Waiting for help

I am having the same problem with an S7 (G930V). During one of the re-flashes, I was able to install the Samsung Product Info App. The CSC product code came up as blank. Not sure if this is normal for this state. Any leads would be appreciated.

Related

[help] "firmware upgrade encountered an issue"

I was trying to install an Official Stock Samsung Galaxy S4 GT-I9505 firmware, from SAMMOBILE Link for the firmware I tried to use: http://www.sammobile.com/firmwares/3/?download=26516. So while flashing it with ODIN, I think it just randomly disconnected, but that just bricked my phone. I don't know whether it is a soft brick or a hard brick, but this is what happens to my phone, every time I turn on my phone whether it's done normally, the download mode or recovery mode method I will be stuck on that screen.
So now I typed in the error on Google to see how it can be fixed. Link to the method to fix the error: http://androidcentral.us/2013/09/how-to-fix-firmware-upgrade-encountered-an-issue-on-kies/
Firstly, my computer (running Windows 7 ULTIMATE 64-BIT) can detect my phone, saying the drivers have been installed successfully. However KIES doesn't detect mine. Anyways I still try to do this method where I have to go to Tools -> Firmware Upgrade and Initialization on KIES. I type in my model name: GT-I9505, that works, now I have to do my S/N or Serial Number: RF1DXXXXXXX, so when I press OK it says GT-I9505 doesn't support 'Intialising', so I am stuck have no idea what to do.
Also, while flashing I tried repartition my S4, to remove all of the stuff I had, none important, except my music which I transferred to my PC. Solved, just flashed Official firmware, it now works.
Just separately repartitioned my S4, it works but S4 is now stuck on boot loop, so have to flash a 4.4.2 Official Firmware.
Harnessful said:
I was trying to install an Official Stock Samsung Galaxy S4 GT-I9505 firmware, from SAMMOBILE Link for the firmware I tried to use: http://www.sammobile.com/firmwares/3/?download=26516. So while flashing it with ODIN, I think it just randomly disconnected, but that just bricked my phone. I don't know whether it is a soft brick or a hard brick, but this is what happens to my phone, every time I turn on my phone whether it's done normally, the download mode or recovery mode method I will be stuck on that screen.
So now I typed in the error on Google to see how it can be fixed. Link to the method to fix the error: http://androidcentral.us/2013/09/how-to-fix-firmware-upgrade-encountered-an-issue-on-kies/
Firstly, my computer (running Windows 7 ULTIMATE 64-BIT) can detect my phone, saying the drivers have been installed successfully. However KIES doesn't detect mine. Anyways I still try to do this method where I have to go to Tools -> Firmware Upgrade and Initialization on KIES. I type in my model name: GT-I9505, that works, now I have to do my S/N or Serial Number: RF1DXXXXXXX, so when I press OK it says GT-I9505 doesn't support 'Intialising', so I am stuck have no idea what to do.
Also, while flashing I tried repartition my S4, to remove all of the stuff I had, none important, except my music which I transferred to my PC.
Just separately repartitioned my S4, it works but S4 is now stuck on boot loop, so have to flash a 4.4.2 Official Firmware.
Click to expand...
Click to collapse
Hi,
Can you get into recovery?
Can you still see your phone in odin?
If so , disable kies (task manager) and try to flash the firmware again.
Wipe data and cache before and after flashing firmware.

Flash Back to Stock ROM on Re-Partitioned Phone

I purchased a Galaxy Edge S7 SM-G935FD Unlocked International Edition (Exynos?) from Amazon US. In an attempt to flash TWRP with Odin, I mistakenly checked re-partition. I thereafter received "an error has occurred while updating the device .... use Emergency Recovery .... in Smart Switch". When I attempt to do so (ie. reinstall stock firmware), I am asked for my Model Number and Serial Number, which I provide. The firmware download appears to complete, but the install does not complete. So here's my questions:
-Givfen my prior repartition, should the Smart Switch Emergency Recovery work, or if not what do I need to do to recover?
-Smart Switch is trying to flash "Initialized Version: : PDAB6 / CSCB4 / PHONEB6 (ACR)". Is that correct for my International Edition?
-I am very confused by the above version code versus the G935FXXU..... firmware codes for rom downloads on websites. What is the correct firmware code for my International Edition?
Thx, Gus
So you need to download the Offical Sammy Firmware for your phone and flash it all via odin
So you can Re-Partition.
Once booted up, repeat your stages avoiding the erros you made the first time./

Need HelP - ODIN gets stucked while flashing

Hello guys,
I need extremely technical help as no longer know what to do.
I have a Galaxy S7 Edge device, which installed the rom BobCat and everything went well until then.
Later I decided to install another rom to test KingRom that left me unsatisfied, because I thought it had some bugs. Had the TWRP 3.0.0 recovery and decided to upgrade to 3.0.2, everything went well.
At one point I do not remember when or how if was when install back, downgrade to TWRP3.0.0, I do not remember if it was via Odin or TWRP, it happens that the installation stopped halfway. Then unplug the device, restarted in recovery mode and got the following message "E: falied to mount EFS (Invalid Argumen)", I could not restart the device (Boot Loop, and stucked at Samsung Logo) except in Recovery Mode, which also made to stay without IMEI number and Serial Number.
I googled until I came to this tutorial:
http://forum.xda-developers.com/s7-e...ssues-t3379516
I followed all the steps explained, I back up EFS_backup and RADIO_bakcup partitions.
Installed FACTORY BINARY G935, everything went well. After restarted, already had the correct IMEI number but still did not present the S / N.
After all that, i tried to install Stock Firmware via Odin, from here started the problems that could not solve.
In the first attempt Odin stucked in "System" (also used the PIT file with the same CSC ... .i do not know if I was right using PIT?). Restarted the device forcibly, entered the stock Recovery, did a complete wipe and always get this message "E: falied to mount System (Invalid argument), I returned to install Factory Binary, then reboot in Recovery and the same message no longer appeared.
Again I try to install the Stock Firmware and Odin always stucks in System, or NAND writing, or Partition, etc. I've tried various Stock Firmware, with and without PIT files, always without success.
Only Factory Binary that successfully installs. The TWRP via Odin also but when device restarts to enter Recovery Mode always get the message at the top of the display:
"Recovery image signature check Fail"
"Reboot to avoid Warranty bit set."
1. Does the partitions are in good shape? how can I check it?
2- I did good or bad using PIT file?
3- Does the problem is running Windows XP through a Virtual Machine?
4 What else can I do?
In all actions used and am using a Macbook 4.1, OsX Lion 10.7.5, Odin 3.11 Windows XP Professional 32bit through Oracle VM VirtualBox 3.4.38
Device:
Galaxy S7 Edge (SM-G935F) CSC = SWC SwissCom
1st Original Firmware: (I guess was 1?) G935FXXS1APG5_G935FVFG1APF3_SWC
Need help Please
Thank you so very much!

[SOLVED] S7 Edge G935FD BootLoop / TWRP Splash Screen Freeze.

Update: [SOLVED]
Thanks GOD .. Kies Emergency Firmware Upgrade Solved it. Same Smart Switch Method.
Help Me please. I flashed TWRP to my SM-G935FD with odin preparing to root it.
But i found the internal storage is 0 bytes.
so i can't find zip file to flash supersu or mount storage to PC.
i found a solution, it was by changing file system and go back to original file system.
i tried this, i changed it. it typed Done. but nothing shows of back or home softkeys of TWRP.
So i restart my device to TWRP again but it freeze in splash screen.
I tried Smart Switch it give me message that it can't recognize my device.
Odin give me FAILED (DeviceInfo).
Any Solution? or My Device is dead now?
When using Samsung SmartSwitch it is normal that it says it does not recognize the device after you have tried to root it and failed.
You need to put the phone in download mode and use the "Emergency Software Recovery and initialization" in the Smartswitch software. You will be asked to input your model number and the serial number. It will then return it to stock.
You do so at your own peril.

Custom binary blocked while flashing combination file

So I have a S8 (SM-G950FD Brazilian unlocked) and it freaked out while updating to the latest firmware. It boots to a screen saying "codification failed" (I translated, it may not say that in an English configured device) and asks for a factory reset wich does nothing. I tried flashing the latest firmware with Odin and nothing.
So while researching I came across combination files, so I downloaded the one for the right binary (5) but it spits out the error "custom binary blocked by frp lock" when flashing with Odin and now I'm stuck.
I would post photos with all the device information in both recovery and download mode with the hope it may show something I don't see but unfortunately, I'm a new user and therefore not able to.

Categories

Resources