Usb file transfer not working onTab A6 with s pen - Samsung Galaxy Tab A series Questions & Answers

no computer recognizes the tablet. no notification or warning when usb is connected to pc. only charging .
i also noticed that the tablet does not charge when its off. but charges fine when switched on. what can i do to resolve thsi issue

It should charge regardless on or off. Use this tool, it will tell you tablet is drawing current properly, the charging current should be around 1.5 Amps with working USB cable and charger.
https://www.ebay.com/sch/i.html?_fr...us+.TRS1&_nkw=usb+voltage+tester&_sacat=92074
USB connector has separated pins for data and charging. So it's normal if a tablet can charge but not data transfer or vice versa.
USB connector is cheap, only around 50 cents but you should know how to solder. A repair shop may charge you more than $50 to replace this 50 cents USB connector.
It takes only 5 to 10 minutes to change the USB port.

Related

Charging via USB Charger

I am on the road a lot and don't want to be carrying the HTC charger with me. For my Treo, I had a foldable USB AC adapter (.8A and 5V) to which I plugged in a Sync and Charge cable and it did just fine.
After reading all the comments about there being two ways to charge a Tilt - fast and slow, I decided to test out a retractable USB data cable with my USB AC brick. I set the option in Power to "Not charge the battery when connected to the PC." and plugged it in. Nothing. I then unticked the box and sure enough, it started to charge. As I was at 70% of the charge, I expected this to drag on, but it didn't. It took about 1 hour and was fully charged.
I'm still a bit worried about charging this way - the description of the Lil Sync cable for the Tilt says that while it might work, under certain circumstances it won't if your battery is below 30% of a charge. Has anyone seen this happen? The last thing I want is to go away for a few days and be stuck with a dead batttery.
Do I need to pick up a special cable from ppctechs or boxwave just to charge? Should I just carry the supplied charger?
I always charge my kaiser just using the sync cable and it works fine even from a flat battery. there seems to be absolutely no need to carry an AC adapter around when you can just connect it to a computer to charge.
Thanks Spooki. Just curious - how long does a charge usually take when you charge against a computer's USB?
it seems to take roughly twice as long as a wall charger but i work with PC's all day so doesn't really bother me, much easier than carrying a charger around.

How to speed up USB charging in Touch HD

I was always wondering how to speed up this unacceptably slow USB charging (If you are in a low signal area with bluetooth ON then the battery is drained far more quicker than the laptop can charge it ending up with a flat battery ). Finally I tested the output from the pins of the wall charger and my Laptop. Even when the laptop is powered off (no data exchange) the USB charging is very slow. The HD seems to send a ~1v pulse through D+ channel when to connect it to USB port (even when powered off the device seems to check if it is a USB data port), but with the charger it does not!, so we need to break this communication.
So I put a thin plastic film over the D+ and D- terminals of the USB cable and voila the device charges much faster..(slightly slower than wall charger - 25% slower, can be accounted for by the lower power output of the laptop USB port, the voltage of laptop usb port is 150-200 mV lower).
While I am typing this my HD has gained 9% charge with screen on!! . Natively it charged atmost 1% by this time with screen off.
Now I am looking for a permanent mod for my spare USB cable hacking off the data lines.
For those in a hurry with nothing but a HD with flat battery USB cable and a computer at hand, worthwhile using a thin paper over the inner two pins of the USB cable on PC side and plugging it in. (You do this at your own risk).
Hope it helps others too. Let me know your experiences.
With my Desktop USB port, charge rate is better than wall charger if you block the data pins. The port seems to be capable of 1.5 amp at 4.96 v
Also ensure that the USB cable snugly fits the mini USB port on HD.
Could this be also the problem why (my) Blackstone doesn't receive a TMC-signal with HyperGPS & iGO8 while charging in my car?
It's a genuine car charger from HTC, so I should say these pins are already "shut" from connection, or am I wrong?
I have a usb cable that is dedicatet for charging. It dosent have D+/- wires. With this cable on my laptop the charge time form about 20% is more than half of regular USD cable..
The cable was supplied with a car BT handsfree.
Regarding the TMC issue Im not shure, Try asking the guys that developed HyperGPS they might know, if not they might be able to fix if they arent aware of the issue
Interesting tip, thanks... I've lost my charger and have been finding it a pain to charge it using the USB port on my laptop.
I cut a small strip of paper from one end of a sticky note, and stuck the adhesive end to the outer flat surface of the USB plug to secure the strip in place. Seems to have done the trick, because the charging light is on and the PC hasn't detected the device. As for how long it takes to charge... will have to wait and see.
Also, I was wondering if there was any difference in charging speed (i.e. when charging via USB normally without using this trick) between activesync and file transfer mode?

Custom charger?

I recently bought a custom 2 amp charger after the stock one died. Anyways, whenever I plug it in, I noticed that it would ask me whether I wanted to access the USB storage. Apps that need the SD card similarly, would terminate (ex: music).
Is there any way to solve this and to make the phone realize that this is a power outlet charger and not a USB charger? I think that the Epic drew about 650 milliamps or so charging and much smaller over PC (I think about 350 to 400 ish IIRC). It seems to currently only be charging at PC USB speeds as well and not the same rate as the stock charger.
Thanks in advance.
There's a way for the phone to tell if it's connected to a PC or AC adapter depending on a resistor shorting out two pins. Make sure you don't have anything other than the +5V and Ground connected.
I had the same thing happen with a car charger. Bridging / shorting the data pins causes the Epic to see the charger as a regular charger, and not usb for data or charging. This can also be done in the cable, itself, however, then you have the problem of having to cut part of your USB cable and re-tape or heat-shrink tube it.
There's a couple threads discussing similar problems/solutions:
http://forum.xda-developers.com/showthread.php?t=908363
http://forum.xda-developers.com/showthread.php?t=709226

Charging without Samsung AC Adapter?

I went out of town this week and made sure to grab my USB cable, but left the AC adapter at home figuring I'd just charge off my laptop via usb. Apparently not... I also tried plugging the USB cord into my iPhone AC/usb adapter with no luck. The only thing I've found is that when you turn off the Tab and connect to one of these devices, a green battery indicator will pop up showing that it is charging. Well, after about 16 hours, it made it from 15% all the way up to 48%. Does anyone know any way around turning it off to charge or why it is barely charging when it is off?
Jaydawgx7 said:
I went out of town this week and made sure to grab my USB cable, but left the AC adapter at home figuring I'd just charge off my laptop via usb. Apparently not... I also tried plugging the USB cord into my iPhone AC/usb adapter with no luck. The only thing I've found is that when you turn off the Tab and connect to one of these devices, a green battery indicator will pop up showing that it is charging. Well, after about 16 hours, it made it from 15% all the way up to 48%. Does anyone know any way around turning it off to charge or why it is barely charging when it is off?
Click to expand...
Click to collapse
Well seeing as it has a 7000mAh battery, just about any run-of-the-mill USB charger isn't going to cut it. The amperage would have higher as well. Now i would hazard that an iPad charger (10 watts) would probably work just fine vs an iPod charger.
Your laptop's USB port isn't providing enough juice to charge fully. With the screen off it will only trickle charge and very slowly at that.
You'll need at least 5 Volt 2 Amp chargers.
You can also try this:
http://forum.xda-developers.com/showpost.php?p=14890063&postcount=16
Or this:
http://cgi.ebay.com/190522553195?ru...ee-All-Categories&_fvi=1&_rdc=1#ht_3085wt_905
I've ordered both last week but neither have arrived yet. I'll report back.
You need a 5vdc supply that will provide 2A. 10W, not 5w as the previous post said. That adapter on ebay won't help the charge, it just disconnects the data line so it does not change its mode when connected to a computer. There are a lot of power supplies that will work and even more that won't, just made sure it supplies 2a. If you want to charge off your laptop then you will want a Y adapter similar to what is on usb powered hard drives but even then you will need to use 2 usb 2.0 or 3.0 ports and will provably only get 1a out.
Sent from my GT-P7510 using XDA Premium App

[Q] Nexus 7 short circut damage help, please.

So, I apparently did something very stupid with my new Nexus 7.
I have a few 1 TB external hard drives, which don't get enough power via an OTG adapter from the Nexus 7 to run. So, I purchased a two into one cable -- that is, a cable that combines two male USB A plugs into one Micro USB B plug so that a USB 3.0 hard drive can use two USB 2.0 ports to have enough power. I had planned to use this to enable use of the hard drives with the Nexus 7 while traveling by plugging one cable in the tablet and the other into a charger.
When I got the cable I tested it by plugging one of the USB A plugs into my Nexus 7, and then I plugged the other into my computer's USB port. The Nexus 7 promptly shut down, the computer complained of a power surge on the USB port, and a distinct smell of melted plastic came from the computer's USB port. I guess the combining cable didn't combine so much as it just acted like a double headed male A USB cable and shorted things out?
The Nexus 7 refused to restart afterwards until I it plugged it into its charger. It works now, mostly. However, if its battery charge is above about eighty-seven percent then it always reports that it is charging, regardless if it is plugged in or not. And if I plug it into a computer while it is reporting that it is charging I have to restart the tablet to get it to connect to the computer -- I guess it thinks it is connected to a charger and doesn't bother checking for a data connection unless restarted.
The level where it stops thinking it's charging varies somewhat -- I've had it still claim to be charging all the way down to eighty-two percent charge, and by repeatedly opening the battery app over and over again I have been able to get it to notice that it's really not charging all the way up to ninety-one percent, but no higher, and I have to open and close the battery app an increasing number of times for every percent that it goes up over eighty-seven before it will notice it's not charging.
Any idea what kind of damage I'm looking at? How to fix it? Whether I can get the warranty people to fix it free of charge? If yes, whether they will send me a new one or just fix the one I have? Whether it's worth getting fixed since it mostly still works, and doesn't really bother me as long as it doesn't get worse?
Nothing?
Nothing from anyone?
Try replacing the internal USB plug? About $25. Easy to do your self.

Categories

Resources