Related
Hi, cut a long story short, I have no ROM downloaded on my phone and I am in recovery. When I boot to system it displays my phone is not rooted and then gets stuck at the boot screen.
This has happened because I factory resetted my phone, then wiped EVERYTHING within recovery, and obviously I wasn't thinking that I would be left without a rom.
What should I do please? How can I get a ROM on to my phone?
Thanks.
jabbarh123 said:
Hi, cut a long story short, I have no ROM downloaded on my phone and I am in recovery. When I boot to system it displays my phone is not rooted and then gets stuck at the boot screen.
This has happened because I factory resetted my phone, then wiped EVERYTHING within recovery, and obviously I wasn't thinking that I would be left without a rom.
What should I do please? How can I get a ROM on to my phone?
Thanks.
Click to expand...
Click to collapse
Hi,
First check if you can go to download mode.
turn off device. then wait few seconds. then press volume down button and plug the usb to your pc. if you see download mode you are good to go. i am waiting for your answer.
or, if my memory serves me well, you can ADB push the ROM, the .zip file over and flash it from recovery.
thanks for your replies guys, I entered download mode and flashed a stock kdz file, this had worked successfully I am now back to lg g2 stock with no root! my phone is amazingly faster but ahh cant survive without root
cheers.
U can root it now. Go ahead
================================
Solution: http://forum.xda-developers.com/one...bootloader-locked-t3212187/page2#post63494201
================================
Hello,
This afternoon, I was preparing to flash Oxygen OS 2.1 through twrp but I wanted to make a backup first. Attempting to load up twrp by holding Vol- and Power, my OPT flashed the starting frame of the boot animation for half a second before turning off. This repeated every 5 seconds. I could still boot OOS normally at this stage.
I decided to reflash twrp so as to make the backups, but on attempting to flash it, I saw that my bootloader was locked. So into fastboot mode I went, but trying to unlock it, it did the same as trying to get into recovery. As soon as I sent the command, "fastboot oem unlock", the screen went dark, flashed the starting frame for the boot animation, and promptly when dark again.
I now can't boot up normally, nor can I enter recovery. I can access fastboot mode, but I can't seem to make any changes.
I've attempted to use this solution as well as several other similar ones with no success.
I've had my OPT since 17th of August with absolutely no signs of trouble until this afternoon.
To me, it seems like it could be a hardware issue, but I'd hope it would last more than 40 days.
Any suggestions?
Thanks.
----
x-post: whirlpool, reddit
The same just happened to me, wtf
Makrilli said:
The same just happened to me, wtf
Click to expand...
Click to collapse
What were you doing before it occurred? Perhaps we can work out the cause.
GusGold said:
What were you doing before it occurred? Perhaps we can work out the cause.
Click to expand...
Click to collapse
I'm not sure what I was doing, I was going to flash different ak kernel as my wifi didn't work.
HOWEVER
I read someone suggesting if you still have bootloop after trying the qualcomm recovery tool, try booting to fastboot and use: fastboot continue
my opt booted nicely to hydrogen os and after I shut it down it no longer bootlooped and I was able to get to recovery.
I'll post this to your reddit thread too, maybe it might help somebody one day, hopefully this works for you too
Makrilli said:
use: fastboot continue
Click to expand...
Click to collapse
Mate! that worked for me too!
However... It only seems to skip the bootloop for that power on. After power off, it returns to the boot loop. I also still can't unlock the bootloader and can't access recovery.
But at least it can boot into OS with fastboot continue!
Thank you.
Weird, after the first successful boot I rebooted and a chinese menu prompted me if I wanted to unlock the bootloader, and I did.
Maybe you should try different recovery packages.
But I'm glad to hear you at least got past the boot loop
Makrilli said:
Maybe you should try different recovery packages.
Click to expand...
Click to collapse
Can't flash a new one since the bootloader won't unlock :/
I guess the phone is in working order at the moment, I just can't let it get turned off without my computer next to me...
GusGold said:
Can't flash a new one since the bootloader won't unlock :/
I guess the phone is in working order at the moment, I just can't let it get turned off without my computer next to me...
Click to expand...
Click to collapse
Nono I mean different qualcomm recovery packages, the ones with MSM8994DownloadTool, I also replaced the stock recovery in the qualcomm package with twrp just in case if that matters
Makrilli said:
Nono I mean different qualcomm recovery packages, the ones with MSM8994DownloadTool, I also replaced the stock recovery in the qualcomm package with twrp just in case if that matters
Click to expand...
Click to collapse
Ahh, do you mind linking me to the one you used?
I think I used this: https://mega.nz/#!EsNQHKab!ifATzg4rxxBniPad0iyxANqlN8cZpUx2MVWaZgEhrD4
but it might have also been this: https://drive.google.com/file/d/0B14IjYN3PtxcSlJ5aGQxX3JERHM/view?usp=sharing
It's also worth mentioning I flashed both a few times before I tried the fastboot continue command so try both a few times and see if that helps, also I replaced the stock recovery with twrp in both recovery packages before flashing.
Edit: And best of luck, I'm rather confident your OPT is going to work properly again.
Boot Loop
I got the same problem.
Phone is rooted and i can't unlock it in cmd, just reboot itself when i try it.
The only way for me to even start the OPT is to (volume+ and power), to get to fastboot mode, then run "fastboot continue" twice in cmd.
If i reboot the phone it get cought in a boot loop where i can see the logo, reboots about every 2 sec.
Is there a solution for this? I've been searching 2 for two days now.
I don't care if i have to reset the entire phone.
p3wb said:
I got the same problem.
Phone is rooted and i can't unlock it in cmd, just reboot itself when i try it.
The only way for me to even start the OPT is to (volume+ and power), to get to fastboot mode, then run "fastboot continue" twice in cmd.
If i reboot the phone it get cought in a boot loop where i can see the logo, reboots about every 2 sec.
Is there a solution for this? I've been searching 2 for two days now.
I don't care if i have to reset the entire phone.
Click to expand...
Click to collapse
And I'm guessing you have tried the qualcomm recovery tool?
And I'm guessing you have tried the qualcomm recovery tool?[/QUOTE]
I got TWRP installed but its unreachable, volume- and power ends in boot loop.
I can´t install anything when the phone is locked.
I even tried a Factory reset, boot loop and no change when i got it up again.
p3wb said:
And I'm guessing you have tried the qualcomm recovery tool?
Click to expand...
Click to collapse
I got TWRP installed but its unreachable, volume- and power ends in boot loop.
I can´t install anything when the phone is locked.
I even tried a Factory reset, boot loop and no change when i got it up again.[/QUOTE]
Yeah but the qualcomm recovery tool that we discussed on the first page?
Sent from my OPT
Makrilli said:
I got TWRP installed but its unreachable, volume- and power ends in boot loop.
I can´t install anything when the phone is locked.
I even tried a Factory reset, boot loop and no change when i got it up again.
Click to expand...
Click to collapse
Yeah but the qualcomm recovery tool that we discussed on the first page?
Sent from my OPT[/QUOTE]
I finally got my OPT working again, tried Qualcomm recovery tool, wasn't able to complete the "MSM8994DownloadTool"
So i downloaded "A2001_14_A.03_150805" in a guide from technobuzz.net/unbrick-oneplus-2/
A similar but it does a entire wipe of the phone, nothing left at all. WARNING!
But i was okey with it.
Well the phone was in Chinese when it was all done but to change language was no problem.
I finally managed to solve it on mine. I had been cautious over the past weeks to not let it run out of battery or get turned off while away from my computer as
Code:
fastboot continue
was the only way I could get past the boot loop.
My core issue to solve was that I couldn't get it recognised as the USB Diagnostic 9006 under Ports in Device Manager. I installed the driver from here manually by right clicking the /qcser/x64/qcser.inf file and selecting install from the context menu. Then, I powered off my OP2. While only holding Vol+ (not power or Vol-), I plugged in my OP2 to the computer and it was finally recognised as the 9006. Then using the recovery tool from the prior link, it installed and rebooted my OP2. The moment of truth was when it rebooted and didn't enter a boot loop!
Then with the Chinese recovery prompt, I selected the top/first option and it brought me to the welcome/first setup screen of OOS.
It wiped the internal memory, and installed OSS 2.0.2 (don't know if coincidence or not as that was my prior OS as well). Now to install twrp and update to the latest OOS hopefully without a hitch.
Happy to finally know it wasn't a hardware issue like a failed eeprom or a dud nand controller as my prior phone (Samsung Note 10.1) died to a failed nand controller as well.
Will update with news of twrp and OOS, but I feel that should go smoothly now. Thanks to the others that helped in this thread too!
Yeap, all good!
Flashed official twrp through fastboot and batch installed OOS2 through 2.1.1 patches and SuperSU. Everything working like new!
Phew.
hi can one of you guys help me out? on teamviewer? mine is stock in the bootloop and i can only get it to boot up via fastboot continue. and i cant figure out how to get it to work. i would like to go back to complete stock and no root
best Martin
gamdiiii said:
hi can one of you guys help me out? on teamviewer? mine is stock in the bootloop and i can only get it to boot up via fastboot continue. and i cant figure out how to get it to work. i would like to go back to complete stock and no root
best Martin
Click to expand...
Click to collapse
Is it recognised as a USB Diagnostic 9006 in your device manager?
Hi GusGold No its 9008
Hello, I own a Lenovo A6010, I recently tried to install a custom rom from a forum in this website, as i am newbie to all this, I think i screwed somewhere. Now my phone is stuck on boot screen. I cannot even start my phone in recovery mode or the menu that takes you to recovery mode.
Before flashing i had taken a backup of the dalvik cache and system and data and all those options available in the backup option in twrp which kept on my pc. Now i dont have any idea what do.
I even downloaded the stock rom of my phone from some website, but it was available in a rar file.
When I connect my phone with a cable while pressing the volume down button the same boot screen pops up and my computer starts to install device drivers. I think my phone can be brought back to normal, but i don't know how.
can someone please help me with some suggestions on what to do with my brick.
Thanks in Advance...
Warm regards
Do you have twrp installed? And by what method exactly did you try to install the custom rom?
Edit: Nevermind. Didn't realise this was a year old thread
Mi A1 bricked, hard resetted it by opening the back cover and shorting two points.
It gets detected by mi flash tool but I cannot flash the stock room. It is giving me "cannot receive hello packet" and then it times out.
Any help will be appreciated.
Thank you.
I'm in the same boat, it's showing up in device manager under ports (COMS & LPT) and in flash tool, yet i cant flash anything
Any help for us?
foggs said:
I'm in the same boat, it's showing up in device manager under ports (COMS & LPT) and in flash tool, yet i cant flash anything
Any help for us?
Click to expand...
Click to collapse
It was solved after I changed the USB port on laptop. I got far as installing tissot_images_7.8.23_20170823.0000.00_7.1_61cf97d794 image and booting to fastboot and then TWRP. But after flashing AOSP extended rom it gave me "The system has been destroyed" screen. And somehow recovery is not staying. It apparently gets wiped after reboot.
udaan said:
It was solved after I changed the USB port on laptop. I got far as installing tissot_images_7.8.23_20170823.0000.00_7.1_61cf97d794 image and booting to fastboot and then TWRP. But after flashing AOSP extended rom it gave me "The system has been destroyed" screen. And somehow recovery is not staying. It apparently gets wiped after reboot.
Click to expand...
Click to collapse
I've also tried different ports, still the same message of the hello packet thing. Also when I have the phone connected to the computer I've a white led light blinking.
From reading other threads here and Xiaomi site the deep flash cable opens the com port, I already have this but won't work. There was something about a loader.img, flashing this to an sdcard and holding power and vol down button it then should boot the loader IMG and rescue the phone, this also fails for me.
foggs said:
I've also tried different ports, still the same message of the hello packet thing. Also when I have the phone connected to the computer I've a white led light blinking.
From reading other threads here and Xiaomi site the deep flash cable opens the com port, I already have this but won't work. There was something about a loader.img, flashing this to an sdcard and holding power and vol down button it then should boot the loader IMG and rescue the phone, this also fails for me.
Click to expand...
Click to collapse
Yup, I ruined one of my usb-C cable trying do do deep flash that way. I failed, so I went to one repair shop and open up the device and did the "two point short thing", which helped to be recognized by the flash tool. Then it showed me that "hello packet" thing.
Then I dug around the Internet for couple of hours and changed the USB port on laptop. I also restarted the laptop after I reinstalled the drivers. Then it actually flashed that ROM I mentioned above. But just that ROM. I tried the latest to oldest versions and all of those ROM would flash but then they will brick the phone again. Only that one worked, i.e. helped me to get to bootloader. But alas it is stuck there, no matter how many times I clean flashed it, it is refusing to boot to system. It gives me "Your SYSTEM HAS BEEN DESTROYED" message on every boot. It only goes to bootloader if I press Volume Up + Power button while booting. And it's a dead end for now. I don't know what else to do.
Also this phone was bought in Hong Kong and its warranty won't work where I am right now. I already took it to the authorized service center and those lazy people told me to change the motherboard and it will cost around $180. So I took it back. lol
Disable driver enforcment to get the hello packet.
TrueMS said:
Disable driver enforcment to get the hello packet.
Click to expand...
Click to collapse
still no hello packet
Your timeout for edl mode has passed
You must press power button for 10-15 sec to power cycle the phone
Or open it up and remove battery socket
Or wait for battery drained out
And after that edl will accept hello package
emprazol said:
Your timeout for edl mode has passed
You must press power button for 10-15 sec to power cycle the phone
Or open it up and remove battery socket
Or wait for battery drained out
And after that edl will accept hello package
Click to expand...
Click to collapse
:victory: Held the power button, clicked flash.. Success :good: it's in the process of flashing now. Thank you
Edit: successful flash now to just let it charge up. Thanks again guys for the help/suggestions ?
Update, i flashed the Oreo stock it gave my a successful flash, let the phone charge to near full. Booted the phone up, got as far as sending information to Google option and the screen became non responsive and the phone rebooted, it did this a few times and I gave up and put it in fastboot mode.
I did another flash using a different option clean flash still with Oreo ROM, I think first time I did it with keeping data not 100% though.. but ended up with the same result of it going into random reboots at different points in the setting the phone up stage.
I've now tried two 7.1.2 stock ROMs with the same results ???
I'll try a custom ROM tomorrow see if that sorts it, if not I'm out of ideas. So freaking close ?
foggs said:
Update, i flashed the Oreo stock it gave my a successful flash, let the phone charge to near full. Booted the phone up, got as far as sending information to Google option and the screen became non responsive and the phone rebooted, it did this a few times and I gave up and put it in fastboot mode.
I did another flash using a different option clean flash still with Oreo ROM, I think first time I did it with keeping data not 100% though.. but ended up with the same result of it going into random reboots at different points in the setting the phone up stage.
I've now tried two 7.1.2 stock ROMs with the same results ???
I'll try a custom ROM tomorrow see if that sorts it, if not I'm out of ideas. So freaking close ?
Click to expand...
Click to collapse
Ur presist partition is damaged..thr are many guides here about recovering it
Do the "factory flash" mode in MiFlash under EDL mode as a last resort. May wipe your IMEI and MAC's, not sure.
Could not receive magic packet is solved by using USB2 port, Windows 7 x86 (32-bit) in a VM, or power-cycling the device and starting over, any or all of the above.
Deep flash cable is only for kicking the phone out of diagnostic mode and into QDFlash mode. Not necessary if using test point. I had to use testpoint method myself, couldn't get deepflash cable to work for getting out of diagnostic mode. I hope I can get it working next time though when I inevitably brick it from repartitioning; as I broke my screen when disassembling
apexashwin said:
Ur presist partition is damaged..thr are many guides here about recovering it
Click to expand...
Click to collapse
No luck with flashing the persist.img either from 7.1.2 or 8.0 stock ROMs. I used the fastboot method and twrp with both ROMs.
I've tried the factory flash with 8.0 ROM in miflash tool this to hasn't solved the problem. It reboots on the set up I unlocked the bootloader to boot twrp flashed persist it reboots as far as bootloader unlocked screen and it stays there. ?
I'm guessing even flashing a custom ROM will do nothing either?
foggs said:
No luck with flashing the persist.img either from 7.1.2 or 8.0 stock ROMs. I used the fastboot method and twrp with both ROMs.
I've tried the factory flash with 8.0 ROM in miflash tool this to hasn't solved the problem. It reboots on the set up I unlocked the bootloader to boot twrp flashed persist it reboots as far as bootloader unlocked screen and it stays there. ?
I'm guessing even flashing a custom ROM will do nothing either?
Click to expand...
Click to collapse
Did you find the guide about fixing constant reboot? It's around somewhere, might be on MIUI forum.
foggs said:
No luck with flashing the persist.img either from 7.1.2 or 8.0 stock ROMs. I used the fastboot method and twrp with both ROMs.
I've tried the factory flash with 8.0 ROM in miflash tool this to hasn't solved the problem. It reboots on the set up I unlocked the bootloader to boot twrp flashed persist it reboots as far as bootloader unlocked screen and it stays there. ?
I'm guessing even flashing a custom ROM will do nothing either?
Click to expand...
Click to collapse
Please try presist resurrector from guides section
I think i've got it back to life.
first tried to flash 7.1.2 stock the earliest one (tissot_images_7.8.23_7.1), it hung on flashing it for nearly an hour with no success, closed the miflash application then tried another 7.1.2 (tissot_images_7.10.30_7.1)flash successful, then in stalled twrp did the persist command and reboot nearly got to the home screen just never getting over the line. then i flashed January 8.0 oreo (tissot_images_8.1.10_8.0) and was able to get on to the home screen/go into settings/enable developer options but it would eventually reboot itself, went back into twrp and did the persist command again and reboot.. success (fingers crossed) now downloading/applying April security update as i type this.
Boo installation problem with the update
looks like i lost my imei, https://forum.xda-developers.com/mi-a1/how-to/guide-how-to-restore-imei-permanently-t3759190 this is going to be a pain.. i'll post back when i try this. need a break from this mess ive made lol
thanks for the help/suggestions appreciated big time.
edit: up to the latest update April 1 security patch.
all done, down to 7.8.23 rom, did the stuff to get the imei back then flashed latest oreo rom
emprazol said:
Your timeout for edl mode has passed
You must press power button for 10-15 sec to power cycle the phone
Or open it up and remove battery socket
Or wait for battery drained out
And after that edl will accept hello package
Click to expand...
Click to collapse
Man, I was trying to fix my Redmi Note 4X for the past 6 hours and you were the ONLY guy to talk about this. Thank you so much. :victory:
THANK YOU
udaan said:
it was solved after i changed the usb port on laptop. I got far as installing tissot_images_7.8.23_20170823.0000.00_7.1_61cf97d794 image and booting to fastboot and then twrp. But after flashing aosp extended rom it gave me "the system has been destroyed" screen. And somehow recovery is not staying. It apparently gets wiped after reboot.
Click to expand...
Click to collapse
man you just solved my problem and saved for me like 180 eur thank you you are a god !!!! Thanks for using this site !!!!!!!!!! <3 <3 <3
udaan said:
It was solved after I changed the USB port on laptop. I got far as installing tissot_images_7.8.23_20170823.0000.00_7.1_61cf97d794 image and booting to fastboot and then TWRP. But after flashing AOSP extended rom it gave me "The system has been destroyed" screen. And somehow recovery is not staying. It apparently gets wiped after reboot.
Click to expand...
Click to collapse
I was unable to flash on MiFlash and after changing USB port I managed to do it!.
Many thanks!
emprazol said:
Your timeout for edl mode has passed
You must press power button for 10-15 sec to power cycle the phone
Or open it up and remove battery socket
Or wait for battery drained out
And after that edl will accept hello package
Click to expand...
Click to collapse
I love you!
Hi guys,
this is my first x compact. I unlocked the bootloader per sony's instructions on their site + what I read here.
I flashed twrp, booted to recovery, and wiped and installed the lineage 16.0 which is stickied.
Everything worked great but various rootcheckers said still not rooted. This bothered me.
I followed the thread (https://forum.xda-developers.com/x-compact/how-to/stock-8-0-root-recovery-t3747479).
I used flashtool to flash stock oreo. After that, bootloops. And can't access recovery.
I can still enter flash mode and fastboot mode, but using the CMD in platform-tools, phone not recognized.
There must be something I can do? Thank you.
pleasuremann said:
Hi guys,
this is my first x compact. I unlocked the bootloader per sony's instructions on their site + what I read here.
I flashed twrp, booted to recovery, and wiped and installed the lineage 16.0 which is stickied.
Everything worked great but various rootcheckers said still not rooted. This bothered me.
I followed the thread (https://forum.xda-developers.com/x-compact/how-to/stock-8-0-root-recovery-t3747479).
I used flashtool to flash stock oreo. After that, bootloops. And can't access recovery.
I can still enter flash mode and fastboot mode, but using the CMD in platform-tools, phone not recognized.
There must be something I can do? Thank you.
Click to expand...
Click to collapse
Use Flashtool again, and this time, before clicking , in the box that says "wipe", check 'userdata'.
Back up anything you want to save in internal storage.
levone1 said:
Use Flashtool again, and this time, before clicking , in the box that says "wipe", check 'userdata'.
Back up anything you want to save in internal storage.
Click to expand...
Click to collapse
Thank you so much. I've seen your name a lot around here, I appreciate you taking the time to help. I'm booting now and starting the root process
pleasuremann said:
Thank you so much. I've seen your name a lot around here, I appreciate you taking the time to help. I'm booting now and starting the root process
Click to expand...
Click to collapse
No problem - I'm messing around with a Samsung at the moment, but I still check in here from time to time. I think XC is my favorite phone so far... XZ2C was really nice too, but (unofficially) official Sailfish OS puts XC on top for me...
levone1 said:
No problem - I'm messing around with a Samsung at the moment, but I still check in here from time to time. I think XC is my favorite phone so far... XZ2C was really nice too, but (unofficially) official Sailfish OS puts XC on top for me...
Click to expand...
Click to collapse
Hi friend, please maybe you can help me. I have almost the same issue. But after using LineageOS for some days, my phone stuck in boot logo. I managed to use Flash Tool to flash latest original stock ROM (Customized IBE). Strangely the flash process ended OK, but the phone still stuck in boot logo. I'm only able to force shut down with Volumen Up+Power Off (3 vibrates). Not possible to enter Recovery Mode.
I'm 98% sure that I have flashed with check in wipe USERDATE and also in CUST-RESET. But I wanted to try again, and now Im not able to enter flashmode. Phone gets green light, when volume down, but Flashstool is not recognizing the phone.
Thanks in advance
jayeffpee said:
Hi friend, please maybe you can help me. I have almost the same issue. But after using LineageOS for some days, my phone stuck in boot logo. I managed to use Flash Tool to flash latest original stock ROM (Customized IBE). Strangely the flash process ended OK, but the phone still stuck in boot logo. I'm only able to force shut down with Volumen Up+Power Off (3 vibrates). Not possible to enter Recovery Mode.
I'm 98% sure that I have flashed with check in wipe USERDATE and also in CUST-RESET. But I wanted to try again, and now Im not able to enter flashmode. Phone gets green light, when volume down, but Flashstool is not recognizing the phone.
Thanks in advance
Click to expand...
Click to collapse
Does fastboot work? Also, what do you ultimately want to do, return to stock?
levone1 said:
Does fastboot work? Also, what do you ultimately want to do, return to stock?
Click to expand...
Click to collapse
yes, after hard work to install drivers, I managed to get the phone to be recognized by Flashtool in fastboot mode. But the phone is not charging when turned off, and its not rebooting. I wanted to try again with stock ROM, since I got some battery issues with LineageOS (phone turned off while playing some games, and worked fine while doing the same with usb cable charging to laptop or AC charger.)
But I cannot do anything right now. Only fastboot mode and force restart works, but it stuck in Sony logo (after normal bootloader unlock 5 seconds warning). What can I do?