ok, the connector is broken.
I disassembled cover parts,
fixed connector,
I'm sure there is 5V inside (the connector inside I measure by voltagemeter) when I plug-in the external charger. The connector has 3 pins for GND and 3 pins for 5V and I'm sure there is volatage inside.
But the battery is not charging. O/S say the battery status as remained, but do to charge.
how to fix? what next to check?
crying:
You could check to see if the protection fuse has blown, if so you can bridge the circuit, if you search for charging or charge on the forum you will find pictures and methods.
the protection fuse just beside the battery? under small piece of white scotch tape?
fixed
thanks for suggestion.
yes, it was broken micro fuse, the one right beside the connector pins on motherboard.
Glad to be of assistance, hope its all ok now. 8)
help
Hi Jgui, could you tell me how you managed to repair borken connector at th bottom??
I search for a repair shop for my MDAII or th way to do it myself...
thanks a lot for your answer
Hi,
I currently repair XDA Exec's for a client of mine who use them for their delivery drivers. They are constantly breaking the screens which are easy to fix, but more often than not they smash off the usb connector and leave it rattling around inside. This is not usually a big problem to fix unless the pads that the 5 pins are soldered to have been ripped off the board. I have found that even if I successfully replace the connector with a new one and solder the two outside pins (which are the gnd and 5v pins) the battery will not charge. The puzzling thing is, if I remove the battery, the red led comes on, presumably indicating power to the device. As soon as I connect the battery the led goes out and the unit boots up only to reveal that it is not charging. So I'm presuming two things:
1. There is some other electronic component damage in the unit caused when the connector broke (due to it being on the end of the charger cable at the time, if this is the case I will scrap the unit)
2. There is some feedback from the battery that the charger needs to continue with it's output and because I didn't reconnect the data pins it won't charge.
Does anyone know how the charging circuit works and what pin / connections are required for charging. I guess the same principle will apply to many PDA's & mobile phones.
Thanks
Rick
http://wiki.xda-developers.com/index.php?pagename=HTC Universal Service Manual
http://pinouts.ru/Slots/USB_pinout.shtml
mini usb is a standart anyway
.Lemon
Hi,
Thanks for your reply, call me a lemon but what utility do I need to unpack a .lemon file ?
Rick
Lemon Head
Forget that last post ok...
I didn't buy the HTC extended battery but one from amazon sold by Karen Deals. Link is below
http://www.amazon.com/gp/product/B0..._m=ATVPDKIKX0DER&pf_rd_r=0NVM3EA1B2VE9HN3AKMA
Battery
Model No: cs-ht8585xl
Part No: 35h000128-00m, ba s400
Rating: 3.7v 2400mah
Lithium Ion
Induction Unit
Palm Pixi charging back with Palm touchstone charging dock
Operating System
Shubcraft 1.4d
Video:
Images are attached below!
Induction charging has the same charging speed as plugging it into a wall outlet. Very fast!
Sidenote:
I tried using a multimeter with the 3 contacts located under the battery and could not get it to register anything (with and without the charger plugged in). I then tried shooting 5v through it using 6 different combination (2 plugs for 3 contacts) and still couldn't get anything. If anyone knows a way to use these 3 contacts for charging please leave feedback. Also if anyone can find a minature microusb male connection that'd be great.
Well done, it's a really nice mod!
The 2400 mAh is a bit too bulky for me, though the extended uptime must be awesome. I'd even consider something similar, were it not that you're using the microusb to charge. If only you could connect it straight to the battery, would be so much more convenient. It'd still work in for instance car kits and attached to a pc.
Never the less, well done.
Looks great, i would try this myself but i cant stand the bulk of extended batteries and the stock metal back would almost defiantly interfere with the current. Where did you get the decal from?
Angelusz said:
Well done, it's a really nice mod!
The 2400 mAh is a bit too bulky for me, though the extended uptime must be awesome. I'd even consider something similar, were it not that you're using the microusb to charge. If only you could connect it straight to the battery, would be so much more convenient. It'd still work in for instance car kits and attached to a pc.
Never the less, well done.
Click to expand...
Click to collapse
You can't plug in directly to the battery since the battery doesn't have a balancer board on it and it would explode if it were to be overcharged without one.
JJbdoggg said:
Looks great, i would try this myself but i cant stand the bulk of extended batteries and the stock metal back would almost defiantly interfere with the current. Where did you get the decal from?
Click to expand...
Click to collapse
I got the decal in the automotive section of Walmart. It came with 2 big/4small stickers for 7usd
UPDATE: Made the microusb head smaller! Letting liquid electrical tape dry then I'll post pics.
this is a really nice mod. what about the possiblly of going via the nav panel connectors instead of micro usb. this would as far as i know leave the usb port free and also not have the disadvantage of having a usb connector attached which can be easily damged.
Personalyu i wouldnt do this mod as i use my phone to tether a hell of a lot so it seems pointless to me, but being able to just sit your phone down and have it charge is awesome.
Great work!!!!
veda_sticks said:
this is a really nice mod. what about the possiblly of going via the nav panel connectors instead of micro usb. this would as far as i know leave the usb port free and also not have the disadvantage of having a usb connector attached which can be easily damged.
Personalyu i wouldnt do this mod as i use my phone to tether a hell of a lot so it seems pointless to me, but being able to just sit your phone down and have it charge is awesome.
Great work!!!!
Click to expand...
Click to collapse
I tired the navpanel connections with no success. If anyone has a multimeter please try to do it to theirs (with charger plugged in).
that is really odd....only think i can think of is manye theres something that needs to happen with the middle pin.
nice work i think that decal are very cute indeed!
PPL this is knowed from a long time! This pins are used for example with Car Kit like CU s400: http://www.slashgear.com/htc-hd2-cu-s400-car-kit-gets-priced-detailed-coming-december-1360143/
This car kit is in two versions: like this on 1st photo - use other battery cover which use this "mysterious" pins to run NaviPanel and charging battery and 2nd version with charging via microUSB port.
I hope this helps a bit.
veda_sticks said:
that is really odd....only think i can think of is manye theres something that needs to happen with the middle pin.
Click to expand...
Click to collapse
This "odd" middle pin you can find in every phone battery too. If you depart any battery you can find there a little electronic circuit.
I think, that this pin is used to metering battery charge, but i can be wrong - im not advanced in electornics.
I'm well aware of the existance of these products but cannot figure out what the three contacts below the batteries are.
Maybe some users having one. In that case he/she can make photos of all connectors or better - check it with multimeter which connector is +, - and this middle one.
Maybe some service manuals can tell something more abt this. I searched for it and i did'nt find nothing useful.
FRANQ_23_PL said:
Maybe some users having one. In that case he/she can make photos of all connectors or better - check it with multimeter which connector is +, - and this middle one.
Maybe some service manuals can tell something more abt this. I searched for it and i did'nt find nothing useful.
Click to expand...
Click to collapse
I also did a search on google and xda but with no luck. I don't think it inputs 5v into the machine since I did shoot 5v into the 3 connectors using different combination.
Hi all,
The contact closest to the center of the phone (looking along the longest axis of the phone) is the +5V, the one furthest from the +5V is the ground, and there's a small voltage on the center contact, positive to ground. These +5V voltage shows up (on my phone) only when the mini-USB charger is plugged in.
I've got the +5V terminal of the Pre plate attached to the +5V contact on the phone, and the other one attached to the GND contact. Inductive charging works at 341ma (as measure by the hardware and read by BattClock) at maximum, which is probably not coincidentally also the limit set on USB charging, at least from my laptop.
I tried hooking the Touchstone up to a Apple ~1" cubed charger, didn't get any charge. I haven't read the USB power specifications, but according to the people at the Palm forums you have to have a USB spec power-capable charger to initialize the Touchstone, and the USB ICs signal this by connecting the two data lines. This can be approximated by clipping a USB cable and twisting the data lines together on the Touchstone side of the cable. This allowed the Apple charger to power the Touchstone.
The HTC stock charger works fine, as does an 800ma Verizon charger I had laying around. I tried hooking the Touchstone up to both a [email protected] switching charger and a 5V 8A supply, the Touchstone still charged at 341ma. I'm guessing this is software, firmware or hardware limited, just like the computer USB connection. I would speculate that if you shorted the middle pin to the ground pin, it might remove this restriction. Or fry your phone, I didn't try it.
There's a guy on the Pre forums who got the Touchstone to consume about 1.02A (http://forums.precentral.net/palm-p...b-adapters-touchstone-dock-2.html#post2020491) so the thing can, apparently transfer some power. I don't know how long it would last at those wattages, but I'm going to read a bit on the USB power spec and see if the 341ma limit can be lifted.
It's kind of nice to use the internal connector, because it leaves the microUSB port open. If anyone has any questions feel free to ask. With the relevant portion of the Pre cover stuck to the back of my phone, there are no wires out of the chassis and the added part doesn't add any considerable bulk to the phone. It protrudes less than the camera.
Anyways, hope this isn't a thread-jack or too long, but I figured it might help anyone that's going to take the time to do this.
Thanks to the community here.
Did you dremel and hotglue the plastic case to the metal case? Interweb highfive from me to you!
Can you post pictures of the inside wiring please?
I did. I basically cut out a square from the HD2 back large enough to hold the coiled length of wire that is needed to allow the back to be removed and articulated. Then I used Super Glue to fix the section of the Pre back containing the inductive coil and circuitry to the HD2 back.
If you're trying to maintain your warranty I might suggest DigiKey part number 478-4687-1-ND, it's from the AVX "MOBO Spring Contact Interconnect Solutions" catalog under battery connectors (I can send you a .pdf copy of the catalog, it's too big to upload to forum). This is a 3mm pitch connector that should mate well with the internal connector - but - I don't have calipers so I would measure before ordering. I just soldered the wires to my HD2.
I'll post some pictures soonish.
And yeah, high five for sure. Thanks for pioneering this. My last phone was retired when the power connector became flaky, so it's nice not to have to worry about the contact wearing out.
Ur mod is on a dutch popular website!
http://tweakers.net/nieuws/69360/mod-maakt-draadloos-laden-mogelijk-op-htc-hd2.html
Right angle micro-usb
I'm looking to do the same thing with my Vibrant and have been searching for a similar connector. I just did a quick google search and found these angled connectors:
http://www.usbfirewire.com/u_microb_cables_angled.html
I tried soldering it your way with no sucess
Soldering pins are as shown
(If viewing vertically with top up)
(leftside of hd2) negative x positive (center of hd2)
bumping an old thread to see if you've taken pictures of the contact points yet.
Sorry it took me so long to reply. Two pictures, the first is the terminal with the wires soldered in, the second shows how I got the cables from the Palm coil/board through the cover. The terminals as you look along the longest axis of the phone with the microUSB plug closest to you are GND, something, and +5v.
So from left to right: 1 GND / 2 ? / 3 +5v.
I fried my charging port socket (don't ask -- coffee, I think). It smelled burned and the charger tip would get hot in the port. I bought a new charging port panel and properly installed it with the protective film removed from the bottom and carefully connected the ribbon cable. The phone will not accept input through the charging port micro USB, but it will charge on a wireless charger. Could I have fried the connector at the battery through which the plug-in power goes? Is there a separate circuit that inputs current from the wireless charger? Could that explain why changing the charging port circuit panel did not fix the problem? Should I buy a new battery and try that? Diagnostic help would be appreciated.
Hi folks,
I'm trying to fix my old Nubia with a broken USB port by bypassing the port.
Since it's soldered to the motherboard, it's almost impossible to solder right on the usb pins.
But I've noticed testpoints, and found the VCC one, on which I soldered a wire. another being soldered to the outside of the port for grounding.
I thought I would be able to charge it that way, but it's not showing any signs of life (with or without the battery)
So I have 2 questions:
-can I charge through the testpoints ?
-do I need to send a signal to the ID pin ? (I guess not, I opened up a charge only cable and it had only 2 wires)
Pic of the connector
I tried charging it with a lab psu and an Aukey Quickcharge 2 charger
Thanks for your help