Help me restore the phone! Nokia 6 TA 1000, after an unsuccessful update, the phone does not turn on.
When the power button is pressed, all the LEDs (green and red) will light, but the screen does not turn on, they go out only when the buttons (+ and -) are pressed long. When connected to a computer, it is defined as the Qualcomm HS-USB Diagnostics 900E port and there's nothing else I can do! How to restore???
Well just download firmware and flash it with ost la
https://forum.xda-developers.com/nokia-6/development/nokia-6-official-firmware-mena-region-t3664441
same6630 said:
Well just download firmware and flash it with ost la
https://forum.xda-developers.com/nokia-6/development/nokia-6-official-firmware-mena-region-t3664441
Click to expand...
Click to collapse
The phone does not enter the download mode, and this program needs the download mode.
First, press and hold Volume Up, Volume Down and Power key for few seconds until you can see "shutdown device:" above the screen, then release them.
Open OST LA and load China Variant Firmware here: https://yadi.sk/d/fN5Oinvt3MwufR
Connect your phone to PC, this will load your phone to Download mode directly.
Now you should be able to flash your phone with OFW.
And you can try to root your phone after you applied November Update.
Or, you can buy an EDL cable for Qualcomm phones from eBay to flash your Nokia 6 from 9008 directly.
hikari_calyx said:
First, press and hold Volume Up, Volume Down and Power key for few seconds until you can see "shutdown device:" above the screen, then release them.
Open OST LA and load China Variant Firmware here: https://yadi.sk/d/fN5Oinvt3MwufR
Connect your phone to PC, this will load your phone to Download mode directly.
Now you should be able to flash your phone with OFW.
And you can try to root your phone after you applied November Update.
Or, you can buy an EDL cable for Qualcomm phones from eBay to flash your Nokia 6 from 9008 directly.
Click to expand...
Click to collapse
Thank you, my dear friend, but nothing happens. The program does not see the phone, so I tried to replace the driver with Qualcomm HS-USB QDLoader 9008, but neither what.
Is there another way to repair the phone? Can try to get to the battery and turn it off for a minute ... or find a TEST POINT ....
Evgeny_14 said:
Thank you, my dear friend, but nothing happens. The program does not see the phone, so I tried to replace the driver with Qualcomm HS-USB QDLoader 9008, but neither what.
Is there another way to repair the phone? Can try to get to the battery and turn it off for a minute ... or find a TEST POINT ....
Click to expand...
Click to collapse
Then you need to do wire trick on your cable, or just use EDL cable.
Short D+ and GND pins when connecting your phone to PC, then press three keys (I mean, Volume Up, Volume Down and Power) on your phone for 15 seconds, then release three keys, disconnect the short line between D+ and GND pins. After that, your phone should enter the Qualcomm 9008 mode directly.
If you don't understand how to short both pins, I'll recommend you to buy Qualcomm EDL Cable on eBay.
Evgeny_14 said:
Thank you, my dear friend, but nothing happens. The program does not see the phone, so I tried to replace the driver with Qualcomm HS-USB QDLoader 9008, but neither what.
Is there another way to repair the phone? Can try to get to the battery and turn it off for a minute ... or find a TEST POINT ....
Click to expand...
Click to collapse
By the way, you can only use QFIL from QPST to unbrick the phone.
hikari_calyx said:
Then you need to do wire trick on your cable, or just use EDL cable.
Short D+ and GND pins when connecting your phone to PC, then press three keys (I mean, Volume Up, Volume Down and Power) on your phone for 15 seconds, then release three keys, disconnect the short line between D+ and GND pins. After that, your phone should enter the Qualcomm 9008 mode directly.
If you don't understand how to short both pins, I'll recommend you to buy Qualcomm EDL Cable on eBay.
Click to expand...
Click to collapse
I have such a cable, and I tried it and as you wrote, the LEDs still light up and the program does not see the phone (((
Evgeny_14 said:
I have such a cable, and I tried it and as you wrote, the LEDs still light up and the program does not see the phone (((
Click to expand...
Click to collapse
Connect your phone with EDL cable to your PC, then press and hold the button on EDL cable when press and hold three keys on your phone until the LED light goes out, now release the button on EDL cable.
hikari_calyx said:
Connect your phone with EDL cable to your PC, then press and hold the button on EDL cable when press and hold three keys on your phone until the LED light goes out, now release the button on EDL cable.
Click to expand...
Click to collapse
That's the problem, the LEDs do not go out, they go out and immediately turn on ...
I disassembled the phone, disconnected the battery connected the cable to the computer, the LEDs caught fire even without the battery ... who knows where the outputs on the TEST POINT???
Evgeny_14 said:
I disassembled the phone, disconnected the battery connected the cable to the computer, the LEDs caught fire even without the battery ... who knows where the outputs on the TEST POINT???
Click to expand...
Click to collapse
Press and hold the button of EDL cable when connecting your phone to PC, then release the button on cable.
Referenced other phones situation, you can also try to press and hold both volume keys.
hikari_calyx said:
Press and hold the button of EDL cable when connecting your phone to PC, then release the button on cable.
Referenced other phones situation, you can also try to press and hold both volume keys.
Click to expand...
Click to collapse
I can not enter the phone in any other way, OST LA does not find the phone (((
Evgeny_14 said:
I can not enter the phone in any other way, OST LA does not find the phone (((
Click to expand...
Click to collapse
Don't use OST LA. Use QFIL from QPST 2.7.460 instead.
hikari_calyx said:
Don't use OST LA. Use QFIL from QPST 2.7.460 instead.
Click to expand...
Click to collapse
Thank you my dear friend for your help, but in the program ... it also does not work out, how else can ...?
Evgeny_14 said:
Thank you my dear friend for your help, but in the program ... it also does not work out, how else can ...?
Click to expand...
Click to collapse
Since you've disassembled Nokia 6, you can remove the battery for 10 seconds, then put it back.
Plug the cable to phone only, then press and hold the button on the cable while connecting to PC, now release the button on the cable, this will boot your phone to 9008 directly.
My Nokia 6 doesn't work，also LED light
18227077056 said:
My Nokia 6 doesn't work，also LED light
Click to expand...
Click to collapse
给你一个提示：我之前对付红米note3的时候，卡900E就是按住音量减和电源十几秒之后，突然就进了fastboot，如果你能找到合适的节奏按下工程线的按钮并放开，就可以进入9008了。
To OP: When I was dealing with Redmi Note 3 that get stuck at Qualcomm 900E, I pressed and Hold Volume Down and Power for few seconds, then it suddenly entered Fastboot mode.
If you can catch the specific time period when press the button on EDL cable, you're able to enter 9008 mode directly.
hikari_calyx said:
给
---------- Post added at 03:40 PM ---------- Previous post was at 03:39 PM ----------
hikari_calyx said:
给
Click to expand...
Click to collapse
Click to expand...
Click to collapse
hikari_calyx said:
Since you've disassembled Nokia 6, you can remove the battery for 10 seconds, then put it back.
Plug the cable to phone only, then press and hold the button on the cable while connecting to PC, now release the button on the cable, this will boot your phone to 9008 directly.
Click to expand...
Click to collapse
Is there any other way ??? The phone even with the battery off and connecting it to the USB still light up the LEDs and determines how the port Qualcomm HS-USB Diagnostics 900E...
Related
Tried using the 935U firmware Odin said it installed correctly but the phone wont power back on ive tried just powering on, holding home power up nothing is turning it on. any suggestions?
Are you able to get back into download mode?
t12icky0 said:
Are you able to get back into download mode?
Click to expand...
Click to collapse
no idea...i hook the usb up to pc it makes noise but screen black. I can hold the power buttons and only way i know it resets or does something is because windows will make the disconnect noise. but it wont let me see anything at all. when i go to device manager is shows the phone as Qualcomm HS-USB QDLoader 9008 (com3) ive tried changing that as well but nothings working. pc recognizes the phone but as that and not the actual phone
Kielbasa99 said:
no idea...i hook the usb up to pc it makes noise but screen black. I can hold the power buttons and only way i know it resets or does something is because windows will make the disconnect noise. but it wont let me see anything at all. when i go to device manager is shows the phone as Qualcomm HS-USB QDLoader 9008 (com3) ive tried changing that as well but nothings working. pc recognizes the phone but as that and not the actual phone
Click to expand...
Click to collapse
Try holding volume down, home and the power key. See if you can access the download mode that way.
t12icky0 said:
Try holding volume down, home and the power key. See if you can access the download mode that way.
Click to expand...
Click to collapse
tried it itll make noise on pc but the screen wont come on at all
What files did you try flashing into the phone?
t12icky0 said:
What files did you try flashing into the phone?
Click to expand...
Click to collapse
Cant flash anything into it cause odin doesnt recognize it now. i been downloading Drivers hoping i can luck out and maybe install it to into Qualcomm HS-USB QDLoader 9008 under device manager cause thats only thing that pops up when the phone is connected to the pc now. shows up as well unspecified but i think as a hub i think i can download firmware and install the drivers individually hopefully might work
Kielbasa99 said:
tried it itll make noise on pc but the screen wont come on at all
Click to expand...
Click to collapse
tried flashing the G935U thought that it was compatible
So download mode or recovery NEVER come up?
Sent from my SAMSUNG-SM-G935A using Tapatalk
smknutson said:
So download mode or recovery NEVER come up?
Sent from my SAMSUNG-SM-G935A using Tapatalk
Click to expand...
Click to collapse
nope i think its hardbricked nothin works to be able to get it to boot into either modes
Can anyone tell me a way so that the pc detects my bricked OPT? I have tried all combinations but its not getting detected at all
phorcus said:
Can anyone tell me a way so that the pc detects my bricked OPT? I have tried all combinations but its not getting detected at all
Click to expand...
Click to collapse
https://forums.oneplus.net/threads/...ck-guide-for-a-hard-bricked-oneplus-2.347607/
Rebel7022 said:
https://forums.oneplus.net/threads/...ck-guide-for-a-hard-bricked-oneplus-2.347607/
Click to expand...
Click to collapse
finally it got detected but when i run MSM8994DownloadTool.exe as administrator and click on start nothing happens
https://1.bp.blogspot.com/-ZZ-sHUBv...ExaIdiLCYRNQCLcB/s1600/Screenshot+%284%29.png
this is where i am stuck please help guys i am in a fix :'(
Are you sure you disabled driver signature enforcing in Windows? You can't install the qualcomm 9008 serial interface driver without doing this, as this driver is not signed by Microsoft.
pitrus- said:
Are you sure you disabled driver signature enforcing in Windows? You can't install the qualcomm 9008 serial interface driver without doing this, as this driver is not signed by Microsoft.
Click to expand...
Click to collapse
yes i did still it doesn't work, any help would be appreciated
If you power up your phone using volume up in fastboot/bootloader mode and then run fastboot devices, does it list your phone? Just making sure the cable connection works.
If yes, then power down your phone by holding power button until screen goes black (making sure you disconnected usb cable first). Then hold volume up while connecting usb cable (don't touch power button), you should hear Windows detecting a new device, check device manager to see that the qualcomm 9008 usb serial port has been successfully installed and with no warning exclamation mark on it. If all is good, you should now be able the launch the download tool and push the download button to start downloading the file partitions to the phone.
pitrus- said:
If you power up your phone using volume up in fastboot/bootloader mode and then run fastboot devices, does it list your phone? Just making sure the cable connection works.
If yes, then power down your phone by holding power button until screen goes black (making sure you disconnected usb cable first). Then hold volume up while connecting usb cable (don't touch power button), you should hear Windows detecting a new device, check device manager to see that the qualcomm 9008 usb serial port has been successfully installed and with no warning exclamation mark on it. If all is good, you should now be able the launch the download tool and push the download button to start downloading the file partitions to the phone.
Click to expand...
Click to collapse
Thanks a lot for writing out to me, but the thing is that my phone is already dead and i had given up all the hope that i had but luckily it got detected and i cannot boot into fastboot mode or bootloader mode the screen is already black, do you think i still have hope? the phone has been detected as qualcomm 9008 in ports in device manager
phorcus said:
Thanks a lot for writing out to me, but the thing is that my phone is already dead and i had given up all the hope that i had but luckily it got detected and i cannot boot into fastboot mode or bootloader mode the screen is already black, do you think i still have hope? the phone has been detected as qualcomm 9008 in ports in device manager
Click to expand...
Click to collapse
Could it be that the actual screen is dead on your phone? But still, since the PC detects the debug port, it should start restoring the phones partitions when you start downloader tool and press the download button up to the left.
hello and thanks for any help phone is china mobile
i done search and read fourms on this and tried many things from flashtool qtsp qilf miflash spflash and also open the phone and disconect battery and reconect still nothing i had got phone for son a yr ago and he brick it so its been sitting till i saw all the new threads so here i am
so i retried steps reloaded drivers disconect batt hold power button to drain any extra juice in batt put it back together still nothing no light dose not get reconize by pc so i ak what else can i try.
[email protected] said:
hello and thanks for any help phone is china mobile
i done search and read fourms on this and tried many things from flashtool qtsp qilf miflash spflash and also open the phone and disconect battery and reconect still nothing i had got phone for son a yr ago and he brick it so its been sitting till i saw all the new threads so here i am
so i retried steps reloaded drivers disconect batt hold power button to drain any extra juice in batt put it back together still nothing no light dose not get reconize by pc so i ak what else can i try.
Click to expand...
Click to collapse
I QFIL with the image below that recovered my K920 CN early this year before I managed to flash LineageOS
https://www.dropbox.com/sh/ktv4xeygsvnxnx1/AACkDn77qloGDLeG14lWVeBca?dl=0
I shared you the folder, please download it and I put in the CN modem file too.
Please do update it that works.
leecs said:
I QFIL with the image below that recovered my K920 CN early this year before I managed to flash LineageOS
https://www.dropbox.com/sh/ktv4xeygsvnxnx1/AACkDn77qloGDLeG14lWVeBca?dl=0
I shared you the folder, please download it and I put in the CN modem file too.
Please do update it that works.
Click to expand...
Click to collapse
thanks for the link but download to my computer? [QUO TE]but what was your preflash steps please was your phone complete dead ir not seen when connected to computer??? this is very important step for as when i connect my phone to pc its not seen at all [/QUOTE] what button combo did you use when plugging cable or did you just plug in to phone and the program self reconize it? did you disconect the battery or not? how do you get around port selection cant falsh unless port is set this has been my issue getting a flash program to see the phone/ but im off to try
[email protected] said:
thanks for the link but download to my computer? [QUO TE]but what was your preflash steps please was your phone complete dead ir not seen when connected to computer??? this is very important step for as when i connect my phone to pc its not seen at all
Click to expand...
Click to collapse
what button combo did you use when plugging cable or did you just plug in to phone and the program self reconize it? did you disconect the battery or not? how do you get around port selection cant falsh unless port is set this has been my issue getting a flash program to see the phone/ but im off to try[/QUOTE]
[email protected] said:
thanks for the link but download to my computer?
Yes.
[QUO TE]but what was your preflash steps please was your phone complete dead ir not seen when connected to computer??? this is very important step for as when i connect my phone to pc its not seen at all
I seen 5 blank drives at phone level, nothing else.
Click to expand...
Click to collapse
what button combo did you use when plugging cable or did you just plug in to phone and the program self reconize it?
typical QFIL steps
did you disconnect the battery or not?
nope. i didnt dismantle the phone.
how do you get around port selection cant falsh unless port is set this has been my issue getting a flash program to see the phone/ but im off to try[/QUOTE]
Please check on the boot Unlock thread and my problem was the USB cable fault after weeks of attempts.
---------- Post added at 05:30 PM ---------- Previous post was at 05:24 PM ----------
[email protected] said:
what button combo did you use when plugging cable or did you just plug in to phone and the program self reconize it? did you disconect the battery or not? how do you get around port selection cant falsh unless port is set this has been my issue getting a flash program to see the phone/ but im off to try
Click to expand...
Click to collapse
[/QUOTE]
probably you need to read thru this, i read thru something similar to unbrick my phone.
http://www.androidbrick.com/ultimat...s-are-unbrickable-qhsusb_dload_qpst_qfil_edl/
leecs said:
what button combo did you use when plugging cable or did you just plug in to phone and the program self reconize it?
typical QFIL steps
did you disconnect the battery or not?
nope. i didnt dismantle the phone.
how do you get around port selection cant falsh unless port is set this has been my issue getting a flash program to see the phone/ but im off to try
Click to expand...
Click to collapse
Please check on the boot Unlock thread and my problem was the USB cable fault after weeks of attempts.
---------- Post added at 05:30 PM ---------- Previous post was at 05:24 PM ----------
[/QUOTE]
probably you need to read thru this, i read thru something similar to unbrick my phone.
http://www.androidbrick.com/ultimat...s-are-unbrickable-qhsusb_dload_qpst_qfil_edl/[/QUOTE]
good moring i tried different usb cables p made a fast boot cable no luck the button combos i tried [holding button atleast 3 sec befor pug usb to laptop]are vol+ usb , vol- usb, vol +- usb, pwr vol+, pwr vol-, pwr vol+- usb, i took apart and remove batt held pwr button to drain any left over power and tried the same combos, i hook my multimeter up and check the voltage both with usb from laptop and ac adapter and got 1.8 i usd screw to frame for ground and found 2 brass contacts on the board that gave me the readings i been trying to find info on unlocking through test points but no luck on this phone so its just my luck lol i know its got to be some program out there or some process to unlock bootloader or something i have posting on few other fourms but its alot of same basic steps and most unbricking threads i found are really not brick at all because if a pc can reconize it then not a brick phone lol i truely have a brick phone and and need that next level trouble shooting lol i guess i need those secret technique the repair shops use but im thinking its just going to be cheaper to replace the pcb if i can find one i did a quick search but did not find my phone but i know its out there just getting through all the bull crap post threads and other none modle related crap but hey info is info and knowledge is power for those to crasp but i will try anything you suggest.
[email protected] said:
Please check on the boot Unlock thread and my problem was the USB cable fault after weeks of attempts.
---------- Post added at 05:30 PM ---------- Previous post was at 05:24 PM ----------
Click to expand...
Click to collapse
probably you need to read thru this, i read thru something similar to unbrick my phone.
http://www.brick.com/ultimate-qualc...s-are-unbrickable-qhsusb_dload_qpst_qfil_edl/[/QUOTE]
good moring i tried different usb cables p made a fast boot cable no luck the button combos i tried [holding button atleast 3 sec befor pug usb to laptop]are vol+ usb , vol- usb, vol +- usb, pwr vol+, pwr vol-, pwr vol+- usb, i took apart and remove batt held pwr button to drain any left over power and tried the same combos, i hook my multimeter up and check the voltage both with usb from laptop and ac adapter and got 1.8 i usd screw to frame for ground and found 2 brass contacts on the board that gave me the readings i been trying to find info on unlocking through test points but no luck on this phone so its just my luck lol i know its got to be some program out there or some process to unlock bootloader or something i have posting on few other fourms but its alot of same basic steps and most unbricking threads i found are really not brick at all because if a pc can reconize it then not a brick phone lol i truely have a brick phone and and need that next level trouble shooting lol i guess i need those secret technique the repair shops use but im thinking its just going to be cheaper to replace the pcb if i can find one i did a quick search but did not find my phone but i know its out there just getting through all the bull crap post threads and other none modle related crap but hey info is info and knowledge is power for those to crasp but i will try anything you suggest.[/QUOTE]
(ok here a update im making progress so i started from the jump went through a box of old micro usb cables found 2 cables that seem to work better than others 1 seems to trigger more often than other but its not a everytime i plug with button combo it pops unrec usb but when it dose sometimes it continues to do it then stops i also found a 3in1 OTG moblie phone connection and when i us it (first just plugging in the OTG to pc it pop unrec device and shows up in
usb controllers) (second when i connect the phone with different button combos the pc detects as unrec usb device but non of the mtk or lenovo nor qualcomm drivers rec the phone i tried to assign the drivers lenovo for it but its there not the rite drivers and the proper ones are installed for the device? "now it did let me assigned and give me the options for some qualcomm usb drivers but the only i rec was a 9006 {it didnt offer the 9008} but after installing it showed with error but still did not rec the phone. so now im not as bad off as i was per say. im going to look into this OTG thing as it really helps pc see the phone as a unrec usb device but no matter which one i use rite now i need to get it to or for the drivers to see the phone.
i still having trouble getting my laptop to asign a driver im getting unrec usb but unable to asign lenovo usb drivers or qaulcomm dirver it tells me there no drivers for it and check to see if the 64bit so my win10 dose not rec those drivers for 64 bit so now im in driver issue now
Please someone help me. I'm on LOS15.1 and was browsing on facebook app while spotify and a VPN app running on background. Suddenly, while scrolling fb feed, spotify stopped playing and screen got hanged. My phone turned off and I thought it was just a random reboot. But unfortunately, it didn't restart anymore nor I can able to turn on the phone.
I tried charging it and nothing's displaying on the screen. I tried pluging it to PC and device manager detected it as "QUSB_BULK".
Is it bricked or something?
Looks like a Qualcomm driver error. I have once fixed this error on a one plus device. But really have no idea how it is done on a dual partition device like miA1
Alanjameson99 said:
Looks like a Qualcomm driver error. I have once fixed this error on a one plus device. But really have no idea how it is done on a dual partition device like miA1
Click to expand...
Click to collapse
Is it possible to flash the device using MiFlash tool? It seems like I can not able to enter fastboot mode.
Brother your phone 900E mode install driver
Edl cable create and edl cable press , volume down and Power press 10 second and boom opening phone fastboot trying bro
Edl cable Google search
Edl cable green and black cable button
Sent from my Mi A1 using XDA Labs
Byramklc said:
Brother your phone 900E mode install driver
Edl cable create and edl cable press , volume down and Power press 10 second and boom opening phone fastboot trying bro
Edl cable Google search
Edl cable green and black cable button
Sent from my Mi A1 using XDA Labs
Click to expand...
Click to collapse
Is that cable plug only thru usb?
Sadly, I have already brought it to a technician. They opened the device to test something from the battery connection then tried to boot up. :crying:
Although it's working fine now.
Three days ago, my phone went off by itself and I had a hard time starting again, it was just loading the bootanimation, I tried to reinstall the ROM, but it did not go into TWRP, although the message Recovery appears on the screen, I insisted and after several attempts, I got into the recovery, formatted everything and I installed the AICP ROM again, and I had to restart,my phone freezes in the LeEco bootloader, then again I insisted until the ROM finally started, but soon realized that it was taking too long to start (30 minutes waiting and nothing).
So I rebooted again, and from then on, I can not go into any mode anymore, trying to access the TWRP, the phone only stays on the Recovery screen until reboot after 2 minutes, when letting the phone try to start the ROM, it only stays on the LeEco screen and restart after 2 minutes, when entering Fastboot, it enters the screen in Fastboot mode, but is not recognized by the computer, not even as unknown device, the same for Download mode.
Is there anything I can try?
Doesn't seem like a a fried motherboard. In my experience, If you fried the CPU, you would still be able to access Fastboot, if you fried the GPU part of the chip, or if the LCD has failed you would feel vibrations..
Do you thin it is possible that you accidentally put the phone into EDL mode? It can sometimes be hard to get out of, and it will give you similar issues.
To leave EDL press and hold volume down and power for 1 minute or longer.
Try this
Install the All in One tool and use it to update your android and fastboot drivers. Afterwards see if the computer recognises the phone port connection by going to Control Panel>System> Device Manager* ( Even though, you may not see the drive, you will maybe still see unknown device or te port)
Maybe a Brick?
If it does not see the phone or show a unknown USB device with port 9008
Try placing the phone into EDL mode by pressing and holding the Vol Up (+) and Vol Down (-) together while simultaneously connecting the phone by USB cable to the computer. Do you see the port or phone now? If you see port 9008 you possibly are bricked, follow the steps on my unbricking thread., if you can not get back to TWRP, or fastboot,and the phone keeps a charge. Then I would think that you are definitely bricked.
Other possible issues
The issue could be the battery. Have you tried using other USB C Cables? If you can use a different usb cable let it charge for a couple of hours then see if you can get into TWRP again . If you can enter fastboot mode try reflashing TWRP, you can use the All in One tool for this.
tsongming said:
Doesn't seem like a a fried motherboard. In my experience, If you fried the CPU, you would still be able to access Fastboot, if you fried the GPU part of the chip, or if the LCD has failed you would feel vibrations..
Do you thin it is possible that you accidentally put the phone into EDL mode? It can sometimes be hard to get out of, and it will give you similar issues.
To leave EDL press and hold volume down and power for 1 minute or longer.
Try this
Install the All in One tool and use it to update your android and fastboot drivers. Afterwards see if the computer recognises the phone port connection by going to Control Panel>System> Device Manager* ( Even though, you may not see the drive, you will maybe still see unknown device or te port)
Maybe a Brick?
If it does not see the phone or show a unknown USB device with port 9008
Try placing the phone into EDL mode by pressing and holding the Vol Up (+) and Vol Down (-) together while simultaneously connecting the phone by USB cable to the computer. Do you see the port or phone now? If you see port 9008 you possibly are bricked, follow the steps on my unbricking thread., if you can not get back to TWRP, or fastboot,and the phone keeps a charge. Then I would think that you are definitely bricked.
Other possible issues
The issue could be the battery. Have you tried using other USB C Cables? If you can use a different usb cable let it charge for a couple of hours then see if you can get into TWRP again . If you can enter fastboot mode try reflashing TWRP, you can use the All in One tool for this.
Click to expand...
Click to collapse
Thanks for answering. I've tried everything.
But I can not see the smartphone when connected. USB drivers are properly installed (I used to recover other LeEco x651, x526 and x520 devices)
I left it restarting for more than hours holding the power button and volume down, no results.
The device does not appear in the Windows device manager in any way, not even as Unknown or 9008 port.
I tried several usb cables.
There is no communication with TWRP or ROM installed and neither with the computer, even though I enter into fastboot / 9008 mode. Only LeEco / recovery logo and Fastboot screen.
I think my main memory is damaged or something.
kakobr said:
Thanks for answering. I've tried everything.
But I can not see the smartphone when connected. USB drivers are properly installed (I used to recover other LeEco x651, x526 and x520 devices)
I left it restarting for more than hours holding the power button and volume down, no results.
The device does not appear in the Windows device manager in any way, not even as Unknown or 9008 port.
I tried several usb cables.
There is no communication with TWRP or ROM installed and neither with the computer, even though I enter into fastboot / 9008 mode.sl Only LeEco / recovery logo and Fastboot screen.
I think my main memory is damaged or something.
Click to expand...
Click to collapse
Well that sucks, if you feel like sending to the phone to China for repair, you can find several shops that are offering to repair any damaged Leeco for $10 and an average cost of $30 for resoldering. On the TaoBao website, use Chrome for translation. Some of their ads mention overseas repair
If it's memory it would be an easy fix for them.
If you don't want to fix it, I highly recommend the Mi8 if it's within your budget, its a perfect phone and you can find them for close to $300. My brother has a Redmi note 6 Pro which is also really nice. He paid $190.
Good Luck.
Sent from my Xiaomi MI 8 using XDA Labs
kakobr said:
Thanks for answering. I've tried everything.
But I can not see the smartphone when connected. USB drivers are properly installed (I used to recover other LeEco x651, x526 and x520 devices)
I left it restarting for more than hours holding the power button and volume down, no results.
The device does not appear in the Windows device manager in any way, not even as Unknown or 9008 port.
I tried several usb cables.
There is no communication with TWRP or ROM installed and neither with the computer, even though I enter into fastboot / 9008 mode. Only LeEco / recovery logo and Fastboot screen.
I think my main memory is damaged or something.
Click to expand...
Click to collapse
Check out this possible do it yourself fix : https://forum.xda-developers.com/showpost.php?p=79302729&postcount=71