Related
I successfully upgraded my Mate 8 to nougat. Then I tried to root the phone. In the middle of flashing superSu, my phone suddenly rebooted and stuck on the bootloop. It never booted again. I tried searching for all the possibilities to unbrick it, but no hope. My mate 8 is bootloader-unlocked. My phone won't boot to trwp even I tried to fashboot flash the it. I really need help from the experts. Thank you all in advance.
I accidentally posted on the wrong subf-forum, please move this post over to the Q&A troubleshooting . thanks you
1.Turn off the phone
2.Connect pc usb cable
3.Hold power+vol down
u should see rescue bootloader page,
now u can flash twrp recovery (for emui5 of course) then u can boot into twrp and do the firmware flashing again
Sent from my HUAWEI NXT-L29 using Tapatalk
amin318 said:
1.Turn off the phone
2.Connect pc usb cable
3.Hold power+vol down
u should see rescue bootloader page,
now u can flash twrp recovery (for emui5 of course) then u can boot into twrp and do the firmware flashing again
Sent from my HUAWEI NXT-L29 using Tapatalk
Click to expand...
Click to collapse
Do Exatly what he said
I did flash the 3.0.2.0-next twrp My phone won't boot to TWRP mode. I don't know if I should flash the stock nougat recovery.img and then flash the twrp.img ?
Was the 3.0.2.0-next right for the nougat ? thanks
After trying to flash twrp many times, the screen is always on " your device is booting now .. "
Did u tried frd-twrp for emui5?
https://mega.nz/#!xg8lVBgJ!4v0DbY-QLGtQVnYvTkTtIXRBmx5q-ZoJp90PSMqlh-U
If it didn't worked try to dload ur last emui4.x via SD card, sometimes it work
Sent from my HUAWEI NXT-L29 using Tapatalk
anthony.ha92 said:
I did flash the 3.0.2.0-next twrp My phone won't boot to TWRP mode. I don't know if I should flash the stock nougat recovery.img and then flash the twrp.img ?
Was the 3.0.2.0-next right for the nougat ? thanks
After trying to flash twrp many times, the screen is always on " your device is booting now .. "
Click to expand...
Click to collapse
If you downloaded from the official TWRP app. It can't be use. You need twrp Nougat that given by @amin318
I successfully unbricked my Mate. It is fully working again. Thank you guys for the help. I really appreciate it.
Flash twrp, flash both update zip and hw_data side by side, reboot to recovery to do a factory reset and then system reboot wait few minutes and then boom, working Mate 8 again.
oh and one more question, im currently on the official beta b521, I found the b563 via the firmware finder.
There are 2 files, one OTA for 400mb, and the other OTA for 1.3 gb. which one should I download in order to upgrade to B563 ? And do I do it by the dload method ?
anthony.ha92 said:
I successfully unbricked my Mate. It is fully working again. Thank you guys for the help. I really appreciate it.
Flash twrp, flash both update zip and hw_data side by side, reboot to recovery to do a factory reset and then system reboot wait few minutes and then boom, working Mate 8 again.
oh and one more question, im currently on the official beta b521, I found the b563 via the firmware finder.
There are 2 files, one OTA for 400mb, and the other OTA for 1.3 gb. which one should I download in order to upgrade to B563 ? And do I do it by the dload method ?
Click to expand...
Click to collapse
Just get the 1.3gb and push it to system updater.
HELP
I need your help¡¡ I have the same error , can you explain that :Flash twrp, flash both update zip and hw_data side by side. tks
Hello,
I tried to flash the RessurectionRemix ROM and it was working well except the LTE so I decided to get back to EMUI.
Problem, i took the backup of bluesmoothie and flashed it but the phone never finish to boot.... (I didn't wipe anything, i thought that the restore function of TWRP was doing everything, am I wrong ?)
Moreover, the TWRP recovery can't access the content of my ext sdcard where the RR ROM is located and even if i put this rom to internal storage, i got the ERROR 7 (this is for deive: can; you have generic_a53)
Do you know what can I do to :
- Come back to EMUI
- Unroot the phone
- Re-lock the bootloader
The files of the TWRP backup are located on the sdcard, if i wipe data/system/cache, will it delete these files ?
Infos :
- Bootloader unlocked
- TWRP of Garak (but still have ERROR 7 now)
Thank you very much
First you need to flash the stock recovery in fastboot. After that you need to put the update.app in a folder called dload in your internal storage.
wangdaning said:
First you need to flash the stock recovery in fastboot. After that you need to put the update.app in a folder called dload in your internal storage.
Click to expand...
Click to collapse
Okay but where can I find the stock recovery ?
Then, do i have to flash it via ADB like i did with TWRP ?
After that, where can I find the "update.app" that you are talking about ?
If i'm right, you're telling me that i can't go back to EMUI without flashing the stock recovery ?
That is correct. First use firmware finder to get the update.app. There is a firmware extractor tool for Huawei firmware. Use it to extract the recovery.img and flash with fastboot.
wangdaning said:
That is correct. First use firmware finder to get the update.app. There is a firmware extractor tool for Huawei firmware. Use it to extract the recovery.img and flash with fastboot.
Click to expand...
Click to collapse
First of all, thank you very much for your anwser, it's very kind of you.
If i understood everything, that's what i have to do :
- Download one of the Huawei firmwares with Huawei Finder (Better get the B100 or another one ?)
- Extract the recovery.img with the update.app from Huawei Finder
- Flash the stock recovery with ADB
Then :
- I put the update.app that i get through the Huawei Finder in the dload folder of the internal storage (If i flash the stock recovery, will I be able to put files in the storage ?)
- I reboot the phone in recovery and normally, it should install the EMUI rom
At the end, my phone will no longer have a custom recvery, bootloader unlocked and root status ?
iSpeeX said:
First of all, thank you very much for your anwser, it's very kind of you.
If i understood everything, that's what i have to do :
- Download one of the Huawei firmwares with Huawei Finder (Better get the B100 or another one ?)
- Extract the recovery.img with the update.app from Huawei Finder
- Flash the stock recovery with ADB
Then :
- I put the update.app that i get through the Huawei Finder in the dload folder of the internal storage (If i flash the stock recovery, will I be able to put files in the storage ?)
- I reboot the phone in recovery and normally, it should install the EMUI rom
At the end, my phone will no longer have a custom recvery, bootloader unlocked and root status ?
Click to expand...
Click to collapse
Yes, that's correct. But you have to put update.app in dload folder on your SD card as far as I know. That's how I did it.
I couldn't find B100 on Firmware Finder and I've got relocked bootloader on Nougat.
Yes, you will need to copy the update.app to internal storage in TWRP, then flash the stock recovery. After flashing you need to hold all three buttons when booting (just like getting into TWRP. After update you will have no custom recovery, no root, and it should lock bootloader.
wangdaning said:
Yes, you will need to copy the update.app to internal storage in TWRP, then flash the stock recovery. After flashing you need to hold all three buttons when booting (just like getting into TWRP. After update you will have no custom recovery, no root, and it should lock bootloader.
Click to expand...
Click to collapse
I did everything, now it's booting but it's VERY VERY LONG... I'll wait and pray
iSpeeX said:
I did everything, now it's booting but it's VERY VERY LONG... I'll wait and pray
Click to expand...
Click to collapse
If it doesn't boot, then boot in recovery and do a factory reset and then it should boot. It happened to me and that's what I did.
#Henkate said:
If it doesn't boot, then boot in recovery and do a factory reset and then it should boot. It happened to me and that's what I did.
Click to expand...
Click to collapse
I still have the warning message "your phone is unlocked", is it normal ?
When i boot into recovery it's displaying "eRecovery" and ask me to download the new update of recovery but it fails when getting the package. I can only reboot and turn off :/
Thank you as always
iSpeeX said:
I still have the warning message "your phone is unlocked", is it normal ?
When i boot into recovery it's displaying "eRecovery" and ask me to download the new update of recovery but it fails when getting the package. I can only reboot and turn off :/
Thank you as always
Click to expand...
Click to collapse
You shouldn't have that message anymore.
Are you sure that the update.app got installed? @wangdaning told you to put it on dload folder in internal memory. I don't know if that is right or if it works, but I've put it in dload folder on sdcard when I've installed update.app.
#Henkate said:
You shouldn't have that message anymore.
Are you sure that the update.app got installed? @wangdaning told you to put it on dload folder in internal memory. I don't know if that is right or if it works, but I've put it in dload folder on sdcard when I've installed update.app.
Click to expand...
Click to collapse
Well i wasn't in front of it when it finished and I just did it : the update stops at 5% and then the phone reboot....
Do you know what do I have to do ? I took the recovery from the last B350 on huawei firmware finder
EDIT1 : but this time in recovery i can Reboot, Wipe factory reset, Wipe cache
iSpeeX said:
Well i wasn't in front of it when it finished and I just did it : the update stops at 5% and then the phone reboot....
Do you know what do I have to do ? I took the recovery from the last B350 on huawei firmware finder
EDIT1 : but this time in recovery i can Reboot, Wipe factory reset, Wipe cache
Click to expand...
Click to collapse
You can read in this post the steps I've used to relock the bootloader and get update (official I guess) through Settings > System update. Just "click to show content".
#Henkate said:
You can read in this post the steps I've used to relock the bootloader and get update (official I guess) through Settings > System update. Just "click to show content".
Click to expand...
Click to collapse
The problem is that the phone doesnt finish to but anymore... i can't do things in menu.
When you talk about SD card, it's the external sd card ? Because i don't have access to it anymore, but i have the partition SD Card
When you installed the B340 update, you seen the percent growing up and had a "success" message ? Because, for me, the update is stuck at 5% and then it reboot the phone
iSpeeX said:
The problem is that the phone doesnt finish to but anymore... i can't do things in menu.
When you talk about SD card, it's the external sd card ? Because i don't have access to it anymore, but i have the partition SD Card
When you installed the B340 update, you seen the percent growing up and had a "success" message ? Because, for me, the update is stuck at 5% and then it reboot the phone
Click to expand...
Click to collapse
Yes, I mean external sdcard.
Reinstall TWRP and restore bluesmoothie's backup and then flash the stock recovery again.
I didn't have any issues with installing the B340 firmware. It was installed successfully.
Try to follow the steps I've used. You shouldn't have any problem.
#Henkate said:
Yes, I mean external sdcard.
Reinstall TWRP and restore bluesmoothie's backup and then flash the stock recovery again.
I didn't have any issues with installing the B340 firmware. It was installed successfully.
Try to follow the steps I've used. You shouldn't have any problem.
Click to expand...
Click to collapse
Okay i'm going to try it right away
My external sd card doesnt show up anymore when i connect it to my PC, i don't know why
I mentioned internal SD card because you said your external was not recognized, but you might try putting the dload folder on external. I have done it both ways. Sometimes the update through stock recovery is finicky. If it doesn't finish run it again. Also, make sure your USB is disconnected, as may Huawei users have mentioned this causes it to freeze. If it still fails, try dloading a different update from firmware finder.
Did it work?
I didn't have so much time these days but I did it and it worked for the 1st part (flash bouesmoothie's backup). Tomorrow I'll do the final step! Thank you again
Here I am :
1 : flashed stock recovery from B350 and i don't have the "unlocked" message anymore !
2 : The update B350 made it, "update success"
3 : It doesn't boot for now
4 : The boot doesn't end
-----
1 : flashed TWRP recovery, launched a factory reset in the same time
2 : Phone booting again on B100
-----
1 : flashed stock recovery from b350
2 : flashed b350 update
3 : Everything is fine !
Thank you for your help !!!
[SOLVED] Hi i was on l-31c432b381 firmware with emui 5.0 and android 7.0, i have unlocked the bootloader for install magisk 12.0 and have root permissions, after months i saw an update for my phone (b389) so i tried to upgrade but i had twrp so error 1 or 7, i flashed the stock recovery, redowload the update and the install failed at 5%, so i tried to unistall magisk before update, but nothing it wont update, after few tries the upgrader says that the update now is not 300mb but is full and is 2gigs, so i think is the time.. but no. so i tried to force the update with 3 buttons recovery dload method but it doesn't work at all 5% at every try. so i searched for support and i found that the ota connot be installed on unlocked devices, so i tried to relock my bootloader with oem relock and the unlock number but it says root type is risk... so i can't even relock my bootloader.. other says that i have to install to relock or can relock... but is b381 the stock? or they instend the mm version? i don't remember what version p9 lite ships. i tried to flash imgs through fastboot but even if i flash system and boot of the b389 the system boot and the info are of the b381, unisatlling app system crash, so i restored my previous backup made through twrp recovery, i immidiatly noticed that the huawei boot animations was gone and was an android stock animation. i thinked it was fine and all was working properly, i give up o upgrade and i was fine but sad. after few hours i tried to make a paper copy with my printer that have nfc but my phone keep shows and hide nfc symbol like on off on off on off over and over even after reboot, after a call i understand that the audio doesn't was working, every type of audio not work even the mic. i don't see any other problems but without sounds is unusable as a phone or mulimedia things... sorry for bad english please HELP i tried all i founded ...
Franseven said:
Hi i was on l-31c432b381 firmware with emui 5.0 and android 7.0, i have unlocked the bootloader for install magisk 12.0 and have root permissions, after months i saw an update for my phone (b389) so i tried to upgrade but i had twrp so error 1 or 7, i flashed the stock recovery, redowload the update and the install failed at 5%, so i tried to unistall magisk before update, but nothing it wont update, after few tries the upgrader says that the update now is not 300mb but is full and is 2gigs, so i think is the time.. but no. so i tried to force the update with 3 buttons recovery dload method but it doesn't work at all 5% at every try. so i searched for support and i found that the ota connot be installed on unlocked devices, so i tried to relock my bootloader with oem relock and the unlock number but it says root type is risk... so i can't even relock my bootloader.. other says that i have to install to relock or can relock... but is b381 the stock? or they instend the mm version? i don't remember what version p9 lite ships. i tried to flash imgs through fastboot but even if i flash system and boot of the b389 the system boot and the info are of the b381, unisatlling app system crash, so i restored my previous backup made through twrp recovery, i immidiatly noticed that the huawei boot animations was gone and was an android stock animation. i thinked it was fine and all was working properly, i give up o upgrade and i was fine but sad. after few hours i tried to make a paper copy with my printer that have nfc but my phone keep shows and hide nfc symbol like on off on off on off over and over even after reboot, after a call i understand that the audio doesn't was working, every type of audio not work even the mic. i don't see any other problems but without sounds is unusable as a phone or mulimedia things... sorry for bad english please HELP i tried all i founded ...
Click to expand...
Click to collapse
Hi, my english is bad too , B389 is an OTA update, its impossible upgrade via fstboot or via TWRP (error 7). IMO the right way to fix your problems - downgrade to MM , then back to Nougat etc. (remove pattern Lock , Fingerprint lock, root etc. before installing downgrade). It will erase all your phone data!!!
Download official rollback package for your VNS-L31C432
http://download-c1.huawei.com/download/downloadCenter?downloadId=93789&version=373429&siteCode=sk
and download MM firmware VNS-L31C432B161 (Single SIM)
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1164/g104/v66022/f1/full/update.zip
1) Create a new folder dload in root directory of SD card (root directory : it means dont put it in any folder .) Now unpack the rollback package and copy its contents “UPDATE.APP” to the “dload” folder. Use the 3 button combo installation. After your firmware version should now be on “B300” or "test-keys".
2) Remove from dload folder rollback package, extract the ZIP file with MM firmware to the dload folder and use 3 combo button installation.
Or you can use this method : on your phone launch the phone dialer app and dial *#*#2846579#*#*. Next, select Project Menu – > Software upgrade – > SDcard upgrade – > and confirm the flashing process that is about to be initiated.
Good luck!
bozka1 said:
Hi, my english is bad too , B389 is an OTA update, its impossible upgrade via fstboot or via TWRP (error 7). IMO the right way to fix your problems - downgrade to MM , then back to Nougat etc. (remove pattern Lock , Fingerprint lock, root etc. before installing downgrade). It will erase all your phone data!!!
Download official rollback package for your VNS-L31C432
http://download-c1.huawei.com/download/downloadCenter?downloadId=93789&version=373429&siteCode=sk
and download MM firmware VNS-L31C432B161 (Single SIM)
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1164/g104/v66022/f1/full/update.zip
1) Create a new folder dload in root directory of SD card (root directory : it means dont put it in any folder .) Now unpack the rollback package and copy its contents “UPDATE.APP” to the “dload” folder. Use the 3 button combo installation. After your firmware version should now be on “B300” or "test-keys".
2) Remove from dload folder rollback package, extract the ZIP file with MM firmware to the dload folder and use 3 combo button installation.
Or you can use this method : on your phone launch the phone dialer app and dial *#*#2846579#*#*. Next, select Project Menu – > Software upgrade – > SDcard upgrade – > and confirm the flashing process that is about to be initiated.
Good luck!
Click to expand...
Click to collapse
Ok i'm posting in real time now. i'm copy update.app in dload folder (rollback)
it have completed ... wow
same android boot animation, the version says is nrd90m test keys (still no audio)
now i'm copying full mm firmware
its installing 40% i'm loving you.. 50% 60% 70%80%90% SUCCESS
user reset... OK
huawei boot animation with audio!!!!!!!!!!!!!!! and there is not unlocked text like (......can't be trusted...)
ok wifi connected skip.skip skip.... start
song... AUDIO WORKING
recording, its working, nfc ok
i'm on b161 and it shows update, now, can i update to the latest version?
THANK YOU SO MUCH
Franseven said:
Ok i'm posting in real time now. i'm copy update.app in dload folder (rollback)
it have completed ... wow
same android boot animation, the version says is nrd90m test keys (still no audio)
now i'm copying full mm firmware
its installing 40% i'm loving you.. 50% 60% 70%80%90% SUCCESS
user reset... OK
huawei boot animation with audio!!!!!!!!!!!!!!! and there is not unlocked text like (......can't be trusted...)
ok wifi connected skip.skip skip.... start
song... AUDIO WORKING
recording, its working, nfc ok
i'm on b161 and it shows update, now, can i update to the latest version?
THANK YOU SO MUCH
Click to expand...
Click to collapse
Yes, you can. Via OTA, or you can use TWRP (Meticulus 3.0.2.0 only ! ) and flash both .zip files. You must download two files:
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G753/g104/v80474/f1/full/update.zip
and
http://update.hicloud.com:8180/TDS/...-L11_hw_eu/update_data_full_VNS-L11_hw_eu.zip.
In TWRP set Install, then select memmory SD card, and klick on
update.zip, confirm installation. After, STAY in TWRP, go back to Install, find file ...hw_eu....zip , confirm installation. Then select rebot system. Done!
bozka1 said:
Yes, you can. Via OTA, or you can use TWRP (Meticulus 3.0.2.0 only ! ) and flash both .zip files. You must download two files:
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G753/g104/v80474/f1/full/update.zip
and
http://update.hicloud.com:8180/TDS/...-L11_hw_eu/update_data_full_VNS-L11_hw_eu.zip.
In TWRP set Install, then select memmory SD card, and klick on
update.zip, confirm installation. After, STAY in TWRP, go back to Install, find file ...hw_eu....zip , confirm installation. Then select rebot system. Done!
Click to expand...
Click to collapse
i've done b371 thrugh updater now it doesn't show newer versions but i'm using b389 dload and it should go ok right? (full b389 update.app)
Franseven said:
i've done b371 thrugh updater now it doesn't show newer versions but i'm using b389 dload and it should go ok right? (full b389 update.app)
Click to expand...
Click to collapse
Try it, but I think, you will get a message "not compatible" . Via dload its impossible, IMO use rather Huawei firmware finder or wait for OTA update.
bozka1 said:
Try it, but I think, you will get a message "not compatible" . Via dload its impossible, IMO use rather Huawei firmware finder or wait for OTA update.
Click to expand...
Click to collapse
yes it failed with b389 dload full
i'm on b371, i've to download and flash manually the b381 and after b389? where i can find otas?
Franseven said:
yes it failed with b389 dload full
i'm on b371, i've to download and flash manually the b381 and after b389? where i can find otas?
Click to expand...
Click to collapse
If I said, it's impossible manually update to 381 or 389 using OTA firmware, trust me . Try Firmware finder. GL!
bozka1 said:
If I said, it's impossible manually update to 381 or 389 using OTA firmware, trust me . Try Firmware finder. GL!
Click to expand...
Click to collapse
i tried full ota (firmware finder) flashes from twrp but gives error 7
e:unknown command [errno]
update_huawei_pkg_from_ota_zip: failed
Franseven said:
i tried full ota (firmware finder) flashes from twrp but gives error 7
e:unknown command [errno]
update_huawei_pkg_from_ota_zip: failed
Click to expand...
Click to collapse
https://m.youtube.com/watch?v=s5hHTZ4LGMM
bozka1 said:
https://m.youtube.com/watch?v=s5hHTZ4LGMM
Click to expand...
Click to collapse
it worked with the dns method not the proxy (was keeping redownload infinite patch over 4gigs tot crazy)
i'm now back at b381 with sound but without my data, i'm trying to reach b389 and over, can i restore through twrp only data partition without a hitch?
in b389 emui is 5.0.1 if i remember right. its data compatible? are the data the cause of no sound? thanks
ALL WORKED FINE , ALL SOLVED. currently b391 (latest) emui 5.0.1 and all my data, super happy thank you
2EDIT: nfc chip still not work, when selected emui crash. minor problem..
note: twrp by (that you said) didn't work in emui 5+ i'm using newer revolution based one twrp 3.03
Franseven said:
it worked with the dns method not the proxy (was keeping redownload infinite patch over 4gigs tot crazy)
i'm now back at b381 with sound but without my data, i'm trying to reach b389 and over, can i restore through twrp only data partition without a hitch?
in b389 emui is 5.0.1 if i remember right. its data compatible? are the data the cause of no sound? thanks
ALL WORKED FINE , ALL SOLVED. currently b391 (latest) emui 5.0.1 and all my data, super happy thank you
2EDIT: nfc chip still not work, when selected emui crash. minor problem..
note: twrp by (that you said) didn't work in emui 5+ i'm using newer revolution based one twrp 3.03
Click to expand...
Click to collapse
FF works with proxy fine, but you must first download and install Firmware finder proxy apk. On Nougat use TWRP 3.1.0-2.
---------- Post added at 21:03 ---------- Previous post was at 20:59 ----------
Franseven said:
it worked with the dns method not the proxy (was keeping redownload infinite patch over 4gigs tot crazy)
i'm now back at b381 with sound but without my data, i'm trying to reach b389 and over, can i restore through twrp only data partition without a hitch?
in b389 emui is 5.0.1 if i remember right. its data compatible? are the data the cause of no sound? thanks
ALL WORKED FINE , ALL SOLVED. currently b391 (latest) emui 5.0.1 and all my data, super happy thank you
2EDIT: nfc chip still not work, when selected emui crash. minor problem..
note: twrp by (that you said) didn't work in emui 5+ i'm using newer revolution based one twrp 3.03
Click to expand...
Click to collapse
FF works with proxy , but you must download and install Firmware finder proxy apk. On Nougat use TWRP 3.1.0-2.
OMG, sorry !
Hello, the problem is what i want restore my Huawei p9 Lite vns-l23c212 but i have installed the EliteRom and the TWRP Elite, so i dont have the partitions (cust, vendor..) and not have a backup of that.
So I downloaded the Find firmware and i downloaded my Huawei version, but i dont have a idea of how install the .zip, i tried using fastboot but when i want install the partitions (cust,vendor..) the console give me a error saying "vendor command failed" or some
I want help from us, sorry for the bad english, im waiting ur comments
Hello,
use rollback method.
First revert your DATA filesystem from
F2FS to EXT4 using TWRP, then follow guide
in UNIFIED HELP THREAD..
Here the link..
https://forum.xda-developers.com/huawei-p9lite/how-to/unified-help-thread-huawei-p9-lite-t3649152
Read carefully, you need L23C212 rollback...
Regards.
Hey
so i have to install the emiui4.1 and then update the huawei until reach to the emui5
Sertinium said:
so i have to install the emiui4.1 and then update the huawei until reach to the emui5
Click to expand...
Click to collapse
Yes, the rollback package will give you
c900 global firmware. From there install
B160 for dual sim, B161 for single sim..
When you will stay with this firmware,
update using updater stock or use Firmware Finder..
Follow the guide..
Regards..
Edit: sorry B160 and B161 are firmware persent in C432 Europe area-
Dont know the one for your cust/region (C212).
Let google do the work for you..
Dadditz said:
Edit: sorry B160 and B161 are firmware persent in C432 Europe area-
Dont know the one for your cust/region (C212).
Let google do the work for you..
Click to expand...
Click to collapse
Okay but the problem now is what in number of compilation say nrd90m test keys and i installed the firmware of my phone
Sertinium said:
Okay but the problem now is what in number of compilation say nrd90m test keys and i installed the firmware of my phone
Click to expand...
Click to collapse
Hello,
according with the guide you flashed
wrong package...
You need FULL OTA UPDATE package, it must be
1.7/1.9 gbytes in size wich cames with data..
Flash new one or repeat the whole process.
I found this firmware on internet,
but do not assume any responsability.
If you want give a try here the direct download..
Check it with an antivirus/antimalware software..
http://download-c.huawei.com/download/downloadCenter?downloadId=92443&version=361914&siteCode=mx
If all will go in the right direction at the end
reboot to e-recovery (vol+ + Power)
and make a factory reset.
Hope this time will work..
Best regards
Dadditz said:
Hello,
according with the guide you flashed
wrong package...
You need FULL OTA UPDATE package, it must be
1.7/1.9 gbytes in size wich cames with data..
Flash new one or repeat the whole process.
I found this firmware on internet,
but do not assume any responsability.
If you want give a try here the direct download..
Check it with an antivirus/antimalware software..
http://download-c.huawei.com/download/downloadCenter?downloadId=92443&version=361914&siteCode=mx
If all will go in the right direction at the end
reboot to e-recovery (vol+ + Power)
and make a factory reset.
Hope this time will work..
Best regards
Click to expand...
Click to collapse
Hello, I have already downloaded that file and I already flashed it but the compilation says that it is C900B130 .... instead of C212B130, so how do I change the cust to C212 ?, because with the other I can not receive the update of emui5, and if the effort with the Finder Firmware gives me the NRD90M test keys.
Sorry for the inconvenience
Sertinium said:
Hello, I have already downloaded that file and I already flashed it but the compilation says that it is C900B130 .... instead of C212B130, so how do I change the cust to C212 ?, because with the other I can not receive the update of emui5, and if the effort with the Finder Firmware gives me the NRD90M test keys.
Sorry for the inconvenience
Click to expand...
Click to collapse
Hello man,
really dont know if i badly explained..
My friend to bring back to MM
you have to strictly follow the guide i posted you..
So you need VNS-L23C212 rollback package then
extract update.app, create a "dload" folder in SD and
pur in it. Turn off and proceed with three buttons method*****
When finished you will have C900 firmware..
(that's a LIMBO firmware)
Delete update.app from SD card...(not dload folder)
Now take tour VNL-L23C212Bxxx firmware,
extract update.app, put in dload folder in SD card
and repeat with three buttons metod.
If all take right direction at end of flash, after booting,
reboot to e-recovery (vol up+ power button) and make a factory reset. Now you have MM firmware..
That's the guide say...
*****= vol up+vol down+power button until It start flashing
That's all my friend...
The other way is to flash L23C212 oeminfo.zip (if you find It)
with TWRP, then VNS-L23C212Bxxx with dload and three
button method. At the end factory reset..
Best regards
same problem,
Dadditz said:
Hello man,
really dont know if i badly explained..
My friend to bring back to MM
you have to strictly follow the guide i posted you..
So you need VNS-L23C212 rollback package then
extract update.app, create a "dload" folder in SD and
pur in it. Turn off and proceed with three buttons method*****
When finished you will have C900 firmware..
(that's a LIMBO firmware)
Delete update.app from SD card...(not dload folder)
Now take tour VNL-L23C212Bxxx firmware,
extract update.app, put in dload folder in SD card
and repeat with three buttons metod.
If all take right direction at end of flash, after booting,
reboot to e-recovery (vol up+ power button) and make a factory reset. Now you have MM firmware..
That's the guide say...
*****= vol up+vol down+power button until It start flashing
That's all my friend...
The other way is to flash L23C212 oeminfo.zip (if you find It)
with TWRP, then VNS-L23C212Bxxx with dload and three
button method. At the end factory reset..
Best regards
Click to expand...
Click to collapse
same problem but it shows update package does not exist.
muhammad22295bilal said:
same problem but it shows update package does not exist.
Click to expand...
Click to collapse
Hello dude please type here your phone model and firmware you're currently using.
Have a happy holidays
unable to mount vendor.
Dadditz said:
Hello dude please type here your phone model and firmware you're currently using.
Have a happy holidays
Click to expand...
Click to collapse
i have installed twrp, creat backup and went on to change the cust to 185 from c432. its bricked , i restored my backup but it went in boot loop with huawei logo, then i want to install coustom rom it said
"failed to mount '/vendor '(invalid argument) "
"failed to mount '/product '(invalid argument) "
its not end yet then i factory reset , restore again this time it doesnt goes to boot loop, but an error message "unable to wipe vendor"
__**** files attached****___
muhammad22295bilal said:
i have installed twrp, creat backup and went on to change the cust to 185 from c432. its bricked , i restored my backup but it went in boot loop with huawei logo, then i want to install coustom rom it said
"failed to mount '/vendor '(invalid argument) "
"failed to mount '/product '(invalid argument) "
its not end yet then i factory reset , restore again this time it doesnt goes to boot loop, but an error message "unable to wipe vendor"
__**** files attached****___
Click to expand...
Click to collapse
Dear user,
I really would like to help you, but do you really want it?
You were stuck on the update problem, you did it on your own and now you have TWRP and backup problems.
Also you did not answer any of my questions,
for me it's ok, but how can someone help you?
Good luck dear ..
Greetings
vns-l21c432 and p9 lite
Dadditz said:
Dear user,
I really would like to help you, but do you really want it?
You were stuck on the update problem, you did it on your own and now you have TWRP and backup problems.
Also you did not answer any of my questions,
for me it's ok, but how can someone help you?
Good luck dear ..
Greetings
Click to expand...
Click to collapse
p9 lite with vns-l21
muhammad22295bilal said:
p9 lite with vns-l21
Click to expand...
Click to collapse
Complete firmware please...
VNS-L21C432B??
TWRP you are using ?
What you're planning to do...
Wish you have a stock firmware / rebrand to C185
or flash a custom roms.
vns-l21c432b504
Dadditz said:
Complete firmware please...
VNS-L21C432B??
TWRP you are using ?
What you're planning to do...
Wish you have a stock firmware / rebrand to C185
or flash a custom roms.
Click to expand...
Click to collapse
the installed frimware was vns-l21c432b504 , then i want to go back to c185 so i installed twrp to make my phone root and to install c185 , it shows error i took restore of backup and phone goes to boot loop with huawei logo, then i again restore failed again. simply i have
p9lite
twrp recovery 3.1.1.0
when i restore my back up at last it shows "unable to wipe vendor" , but when i install other imges file it shows
"unable to mount vendor "
"unable to mount product".
now i just want my working phone back please healp
muhammad22295bilal said:
the installed frimware was vns-l21c432b504 , then i want to go back to c185 so i installed twrp to make my phone root and to install c185 , it shows error i took restore of backup and phone goes to boot loop with huawei logo, then i again restore failed again. simply i have
p9lite
twrp recovery 3.1.1.0
when i restore my back up at last it shows "unable to wipe vendor" , but when i install other imges file it shows
"unable to mount vendor "
"unable to mount product".
now i just want my working phone back please healp
Click to expand...
Click to collapse
Hello dear,
We will try to make your last one work
system, ie the L21C432B504.
Do you still have access to the system?
Do you have access to TWRP?
Do you have access to fastboot?
You have tried to install the oeminfo file
and this may have closed the bootloader,
so I invite you first, even if it says that it is unlocked, to re-unlock it,
but not before you have made backups of your stuff, as a factory reset will be done.
Reply me when you ready ...
here is your answers brother.
Dadditz said:
Hello dear,
We will try to make your last one work
system, ie the L21C432B504.
Do you still have access to the system?
Do you have access to TWRP?
Do you have access to fastboot?
You have tried to install the oeminfo file
and this may have closed the bootloader,
so I invite you first, even if it says that it is unlocked, to re-unlock it,
but not before you have made backups of your stuff, as a factory reset will be done.
Reply me when you ready ...
Click to expand...
Click to collapse
no access to system,
access to twrp
access to fasatboot
bootloader and phone both unlocked.
muhammad22295bilal said:
no access to system,
access to twrp
access to fasatboot
bootloader and phone both unlocked.
Click to expand...
Click to collapse
Ok dude reboot to fastboot and
unlock again your bootloader.
After factory reset see if have access to system...
Tell me...
no access to system.
Dadditz said:
Ok dude reboot to fastboot and
unlock again your bootloader.
After factory reset see if have access to system...
Tell me...
Click to expand...
Click to collapse
after unlock bootloader , cant access to system
I folowed this tutorial https://forum.xda-developers.com/nova-plus/development/rom-aospextended-v4-6-t3717372 and all flashing was fine. Due to some inconveniences of this new flashed rom i decided to restore to default rom. I extracted recovery and update.app version Can-L11 B396 i think from firmware finder and flased with adb this recovery. After that, it asked me to do an factory reset, i did it, but it wont boot any of huawei or Aosp Extended. The main problem i have is i can`t acces any more my phone with adb terminal, maybe after flashing the new original recovery usb debbuging reverted to un-enabled. How can I do now? Thanks in advance.
campeadore said:
I folowed this tutorial https://forum.xda-developers.com/nova-plus/development/rom-aospextended-v4-6-t3717372 and all flashing was fine. Due to some inconveniences of this new flashed rom i decided to restore to default rom. I extracted recovery and update.app version Can-L11 B396 i think from firmware finder and flased with adb this recovery. After that, it asked me to do an factory reset, i did it, but it wont boot any of huawei or Aosp Extended. The main problem i have is i can`t acces any more my phone with adb terminal, maybe after flashing the new original recovery usb debbuging reverted to un-enabled. How can I do now? Thanks in advance.
Click to expand...
Click to collapse
Check this post.
I cant access my phone via adb or twrp recovery. I wonder why. Before flashing a stock recovery all Was fine, adb Was connecting with no problem.
campeadore said:
I cant access my phone via adb or twrp recovery. I wonder why. Before flashing a stock recovery all Was fine, adb Was connecting with no problem.
Click to expand...
Click to collapse
Try to flash the TWRP again with fastboot.
PS: I don't understand how you people end up like this. It never happened to me.
I cant, adb cant be connected to device. Says null operation.
finally i succeed to revert o stock rom. Now i have on About phone CAN-L11C432B397, Emui 5.0 and Android 7.0. One question please, I dont see anymore the Update system tab or something, "Actualizator" on romanian language. Is that normal? How i can check for updates?
campeadore said:
finally i succeed to revert o stock rom. Now i have on About phone CAN-L11C432B397, Emui 5.0 and Android 7.0. One question please, I dont see anymore the Update system tab or something, "Actualizator" on romanian language. Is that normal? How i can check for updates?
Click to expand...
Click to collapse
You need to install the other zip too which has the word "data_full" at zip's name or something like that.
EDIT: @campeadore, i suggest you to edit the thread name and add "[SOLVED]" at begin and write the way you've fixed your phone (the solution), so it'll help other people who might run into the same problem as you.
I`ll do it as soon i fully resolve the problem. I followed your link and everything went fine at step 1 (Go back to EMUI 4.1 (MM). System is booting, but system update is not working. So, i want to flash EMUI 5, but can-l11c432b330 or can-l11c432b396 cant be updated, around 45% gives an error. The only version who work is can-l11c432b320 but i dont have update_full_CAN-L11_hw_eu, only the first update.zip.
campeadore said:
I`ll do it as soon i fully resolve the problem. I followed your link and everything went fine at step 1 (Go back to EMUI 4.1 (MM). System is booting, but system update is not working. So, i want to flash EMUI 5, but can-l11c432b330 or can-l11c432b396 cant be updated, around 45% gives an error. The only version who work is can-l11c432b320 but i dont have update_full_CAN-L11_hw_eu, only the first update.zip.
Click to expand...
Click to collapse
Newer / newest firmware downloaded from Firmware Finder needs to be approved by Huawei and that can take some time. It's failing to install because it wasn't approved. I've read this in past somewhere.
Try B381 or B382 as i've always installed that one when i've went back to EMUI 5.
Yes, i did it now with can-l11c432b330. I think my mistake was trying to flash to EMUI5 with usb cable connected. With cable off all went fine like a charm. Now i do all approved updates with system update. Thank you so much man, really appreciated.
Seeking help: I have a smartphone huawei nova lite plus (TRT LX1) that fails to restart. It goes continuously in a loop. Entering recovery only the first 2 functions come out: wipe wash factory reset and wipe wash partition. Then using eRecovery from PC with the USB cable, proceed up to a certain point and then not continue. I think it's in soft brick. I definitely need the right software for flashing, stock roms and usb drivers. Where can I find them? Many thanks