No idea what possessed me to do it (it was late), I unchecked "OEM Unlock", and bricked my phone.
(Android 5.1.1, stock recovery, rooted)
It's stuck in a bootloop with the red message "Custom binary blocked by FRP lock."
I've read many other posts stating that flashing stock firmware will unbrick the phone. That's great, the hardware can be saved. But I need the data; contacts, txts, photos.
What are my options?
Is there any way around FRP lock? I understand tit's intended as a security feature, and basically only happens when people do idiot stuff like unchecking OEM Unlock. So I doubt many devs/hackers have put much focus on developing workarounds.
Theoretically, Samsung may have the capacity to unlock the FRP lock. Is this a thing? Does anyone know anything about sending it to a Samsung tech center? Probably they would have difficulty guaranteeing the phone sender should have rightful access to the phone, so perhaps they provide no pathway?
@ashyx, I've read your posts, you're frankly a wizard. Any thoughts? Thanks
Frustrated with myself,
- Scott
ScottHW said:
No idea what possessed me to do it (it was late), I unchecked "OEM Unlock", and bricked my phone.
(Android 5.1.1, stock recovery, rooted)
It's stuck in a bootloop with the red message "Custom binary blocked by FRP lock."
I've read many other posts stating that flashing stock firmware will unbrick the phone. That's great, the hardware can be saved. But I need the data; contacts, txts, photos.
What are my options?
Is there any way around FRP lock? I understand tit's intended as a security feature, and basically only happens when people do idiot stuff like unchecking OEM Unlock. So I doubt many devs/hackers have put much focus on developing workarounds.
Theoretically, Samsung may have the capacity to unlock the FRP lock. Is this a thing? Does anyone know anything about sending it to a Samsung tech center? Probably they would have difficulty guaranteeing the phone sender should have rightful access to the phone, so perhaps they provide no pathway?
@ashyx, I've read your posts, you're frankly a wizard. Any thoughts? Thanks
Frustrated with myself,
- Scott
Click to expand...
Click to collapse
As advised flash the stock firmware. DATA won't be affected.
ashyx said:
As advised flash the stock firmware. DATA won't be affected.
Click to expand...
Click to collapse
Really? Many posts I've seen have noted that "all user data will be deleted".
Do I just use ODIN, and flash AP? No app, or user data will be erased, or formatted like that?
A few mention "Initializing with Smart Switch"; I haven't done that before. Is that different than flashing firmware?
ScottHW said:
Really? Many posts I've seen have noted that "all user data will be deleted".
Do I just use ODIN, and flash AP? No app, or user data will be erased, or formatted like that?
A few mention "Initializing with Smart Switch"; I haven't done that before. Is that different than flashing firmware?
Click to expand...
Click to collapse
Searching for that question directly, it seems like flashing a ROM (e.g. stock firmware) will not directly erase user data; downloads, photos in DCIM, etc.
But, sounds like any user-installed apps will be erased (so any internally stored data would be lost).
And, data stored in system apps would be lost, too; e.g. tabs that were open in Chrome.
There's no way around the FRP lock, eh?
Here is Samsung's statement about FRP (Factory Reset Protection)
It describes the Google account "protection" features, but doesn't really describe how FRP lock leads to bootloops.
https://www.samsung.com/us/support/frp/
Factory Reset Protection (FRP) Feature
What is Device Protection, or Factory Reset Protection (FRP)?
Android devices provide built-in security features you can use to protect your device and information, including screen locks and data encryption. Data protection, or Factory Reset Protection (FRP), is a security feature on Android devices with Lollipop 5.1 and higher.
FRP is automatically activated when you set up a Google Account on your device. Once FRP is activated, it prevents use of a device after a factory data reset, until you log in using a Google username and password previously set up on the device.
How does FRP work?
When you perform a Factory Data Reset, all settings are returned to the factory default settings. All data is erased, including files and downloaded apps.
If you have a Google Account set up on the device, FRP is active. This means that after the reset, you'll be required to log in to the Google Account using the username and password. If you have multiple Google Accounts set up on the device, you can log in using any of the accounts.
If an unauthorized person tries to reset the device by another method, the device would still require log-in using the Google username and password. This means that if your device is lost or stolen, another person would not be able to reset it and use it.
What do I need to know about FRP?
If you want to reset your device to factory defaults, make sure you know your Google Account and password, because you'll need to log in at the end of the reset.
If you want to reset your device to factory defaults, but don't remember your Google username and/or password, you can do one of these:
Check your devices Account settings for your account name, and reset your password via the device or at www.google.com.
It can take 24 hours for the password reset to sync with all devices registered to the account.
Remove the account before you reset the device.
If you already reset your device, but don't remember your Google username and/or password, the device can't be used. In that case, you can do one of these:
If you know your Google username but can't remember the password, you can reset your password on the device, or at www.google.com. It can take up to 24 hours for a new password to sync with all registered devices. After 24 hours, you can try logging in to your phone with the new password.
If you have multiple Google Accounts, and you can't remember which Google Account you set up on your device, visit https://www.google.com/android/devicemanager.
Log in with your Google username and password and check the list of devices registered to the account. If you don't see the device listed on the account, it means the device is registered to a different account. Use the same process to check for devices linked to your other Google Accounts. When you find the registered account, use it to log in to your device.
If you can't remember any of your Google Account information, you can send your device, along with proof of purchase, to an authorized Samsung Service Center. Samsung has special tools to reset the phone to factory defaults with no protection enabled.
Click to expand...
Click to collapse
Looking for a Samsung Authorized Support Center, apparently there are ZERO listed around Omaha, NE.
http://support-us.samsung.com/cyber/locator/asc_locator.jsp
There must be ASC's somewhere; I'm hesitant to mail the phone away because I think the tech will just wipe it. The whole point is to maintain the data :-/
What do I need to flash to remove "Custom binary" ?
Will flashing the bootloader back to stock unlock the FRP lock?
That's BL throuh ODIN, right?
Do I have to flash AP ?
Won't that remove all user apps and their data, and any user data associated with system apps?
ScottHW said:
What do I need to flash to remove "Custom binary" ?
Will flashing the bootloader back to stock unlock the FRP lock?
That's BL throuh ODIN, right?
Do I have to flash AP ?
Won't that remove all user apps and their data, and any user data associated with system apps?
Click to expand...
Click to collapse
Not being funny, but you're panicking over nothing. I can pretty much guarantee you will NOT lose any data, apps or settings. The DATA partion is untouched by stock firmware.
Just flash the whole stock firmware(not repair firmware) and you'll be fine.
If you're super paranoid about losing data then just flash the AP part.
ashyx said:
Not being funny, but you're panicking over nothing. I can pretty much guarantee you will NOT lose any data, apps or settings. The DATA partion is untouched by stock firmware.
Just flash the whole stock firmware(not repair firmware) and you'll be fine.
If you're super paranoid about losing data then just flash the AP part.
Click to expand...
Click to collapse
Thanks for the reassurance. I am pretty paranoid, because I feel like such an ass for making such a dumb mistake.
Will I lose:
Contacts?
Text messages??
Chrome Bookmarks???
My numerous open Chrome tabs?!?!
I'm just trying to understand what's happening, know what I'm doing.
Because I was clearly stupid enough to uncheck OEM Unlock. (WTF was I thinking?!)
ScottHW said:
Thanks for the reassurance. I am pretty paranoid, because I feel like such an ass for making such a dumb mistake.
Will I lose:
Contacts?
Text messages??
Chrome Bookmarks???
My numerous open Chrome tabs?!?!
I'm just trying to understand what's happening, know what I'm doing.
Because I was clearly stupid enough to uncheck OEM Unlock. (WTF was I thinking?!)
Click to expand...
Click to collapse
It will be exactly as it was before. Nothing will change.
There are only 2 binaries that need flashing, boot and recovery, however unless you are flashing the exact firmware you had previously you may get compatibility issues, so it's best to just flash the whole firmware.
ashyx said:
It will be exactly as it was before. Nothing will change.
There are only 2 binaries that need flashing, boot and recovery, however unless you are flashing the exact firmware you had previously you may get compatibility issues, so it's best to just flash the whole firmware.
Click to expand...
Click to collapse
Thanks for the more specific information.
I've never found any discussions about how to solve the frp lock bootloop, with the intention of preserving user data.
If you will indulge me a bit more, I'd like to learn, test, and then share this for others.
Do you know exactly Custom binary blocked by FRP lock ""security" works?
Where is the flag that gets tripped?
In order to solve this bootloop, technically just Boot loader and Recovery need to be flashed (the exact versions must be used, or comparability issues can occur).
Bootloader should be simple enough: BL is one of the specific upload choices in Odin.
Recovery is a .bin that's contained with the AP.tar, correct?
Is it possible to specifically flash only the Recovery?
(I am reading other posts and pages as I write this, sorry if some of these points and questions seem "obvious"; I'm still learning. Aren't we all )
This thread is particularly detailed re: ODIN flashing, although it is from 2013, and for a specific device
https://forum.xda-developers.com/showthread.php?t=2154762
ScottHW said:
Thanks for the more specific information.
I've never found any discussions about how to solve the frp lock bootloop, with the intention of preserving user data.
If you will indulge me a bit more, I'd like to learn, test, and then share this for others.
Do you know exactly Custom binary blocked by FRP lock ""security" works?
Where is the flag that gets tripped?
In order to solve this bootloop, technically just Boot loader and Recovery need to be flashed (the exact versions must be used, or comparability issues can occur).
Bootloader should be simple enough: BL is one of the specific upload choices in Odin.
Recovery is a .bin that's contained with the AP.tar, correct?
Is it possible to specifically flash only the Recovery?
(I am reading other posts and pages as I write this, sorry if some of these points and questions seem "obvious"; I'm still learning. Aren't we all )
This thread is particularly detailed re: ODIN flashing, although it is from 2013, and for a specific device
https://forum.xda-developers.com/showthread.php?t=2154762
Click to expand...
Click to collapse
No, I didn't mention the bootloader, that is a different part of the firmware. The boot and recovery images have a .img extension and should be flashed under AP.
It is the bootloader that detects non official firmware and trips the FRP flag. If it's disabled in settings via OEM UNLOCK the bootloader ignores it and allows the device to boot.
n00b mistake
ashyx said:
No, I didn't mention the bootloader, that is a different part of the firmware. The boot and recovery images have a .img extension and should be flashed under AP.
It is the bootloader that detects non official firmware and trips the FRP flag. If it's disabled in settings via OEM UNLOCK the bootloader ignores it and allows the device to boot.
Click to expand...
Click to collapse
Sh!t, sorry, boot.ing /= bootloader. Rookie mistake. #StillLearning
OK, so boot.img and recovery.img should both be contained within the AP component of stock firmware.
I can just flash those two, can't I?
ashyx said:
No, I didn't mention the bootloader, that is a different part of the firmware. The boot and recovery images have a .img extension and should be flashed under AP.
It is the bootloader that detects non official firmware and trips the FRP flag. If it's disabled in settings via OEM UNLOCK the bootloader ignores it and allows the device to boot.
Click to expand...
Click to collapse
Is there any non-GUI way to toggle the OEM UNLOCK?
Bootloader? Download mode? Recovery? Fastboot? ADB?
I assume not, since that might be a "security" risk. And also, if there were, problems like this would have solutions posted mentioning how to do that.
Sh!!!!!!!t... I was thinking I would have screenshots of the exact build that's loaded on my phone. That way I can find the right stock firmware.
Seems those screenshots are still in the phone, didn't get moved to external memory
All I know for sure is it's Andorid 5.1.1, but that probably isn't specific enough to get the exact right boot and recovery images.
I intend to flash the boot.img and recovery.img to my phone. Hopefully, this will avoid any data loss, while clearing the FRP lock bootloop.
I got the stock firmware for Android 5.1.1 for my Galaxy A3 (2016) (SM-A310M) here:
https://www.sammobile.com/firmwares/galaxy-a3-/SM-A310M/TTT/download/A310MUBU2APE2/73991/
This set of instructions says to extract the .img file(s) to flash, then just .tar them up using 7zip, and flash it as AP in ODIN.
http://howto.highonandroid.com/sams...extract-stock-recovery-from-samsung-firmware/
But... this one says to use Unified Android Toolkit, option ‘8’ (Create an Odin flashable tar), and then flash with ODIN.
https://skipsoft.net/flashing-a-single-partition-i-e-system/
Fortunately, I have a Galaxy A3 (2017) (SM-A320Y), which I was just about to upgrade to for my daily driver. It's blank, running Android 7.0, so it means I can test this process, see if data is preserved, with almost no risk to actual data. Got that firmware here:
https://www.sammobile.com/firmwares/SM-A320Y/COO/download/A320YDXU1BQH2/189605/
Ironically... I don't yet have a great method to intentionally trip the FRP lock bootloop
I think rooting and then unchecking OEM Unlock should do it (that's what wrecked my A310M)
FRP lock - Usb does not recognize
Hi, Everyone!
Sorry my english.
My problem is the same as yours.
however, after this frp lock message appeared, my phone goes into download mode, but the pc does not recognize any more. what can i do to get flash from the rom stock and solve the frp lock problem.
Help me, please!
Thank you all
ScottHW said:
No idea what possessed me to do it (it was late), I unchecked "OEM Unlock", and bricked my phone.
(Android 5.1.1, stock recovery, rooted)
It's stuck in a bootloop with the red message "Custom binary blocked by FRP lock."
I've read many other posts stating that flashing stock firmware will unbrick the phone. That's great, the hardware can be saved. But I need the data; contacts, txts, photos.
What are my options?
Is there any way around FRP lock? I understand tit's intended as a security feature, and basically only happens when people do idiot stuff like unchecking OEM Unlock. So I doubt many devs/hackers have put much focus on developing workarounds.
Theoretically, Samsung may have the capacity to unlock the FRP lock. Is this a thing? Does anyone know anything about sending it to a Samsung tech center? Probably they would have difficulty guaranteeing the phone sender should have rightful access to the phone, so perhaps they provide no pathway?
@ashyx, I've read your posts, you're frankly a wizard. Any thoughts? Thanks
Frustrated with myself,
- Scott
Click to expand...
Click to collapse
FRP Custom binary Lock
ashyx said:
It will be exactly as it was before. Nothing will change.
There are only 2 binaries that need flashing, boot and recovery, however unless you are flashing the exact firmware you had previously you may get compatibility issues, so it's best to just flash the whole firmware.
Click to expand...
Click to collapse
Could you help me to get access to my data? I'm running port of S8 on my S7 and got bootloop. Someone told me that even if I'll flash AP only I might lose my data because of difference in the way the memory is formatted.
Blackion said:
Could you help me to get access to my data? I'm running port of S8 on my S7 and got bootloop. Someone told me that even if I'll flash AP only I might lose my data because of difference in the way the memory is formatted.
Click to expand...
Click to collapse
If they're both stock based firmware then you can just flash the stock S7 firmware. Data should remain untouched.
Hi
I am just stuck with the same problem. I have downloaded the latest Stock ROM. But unsure which options to select in ODIN and what files to select.
I presume only select AP. Also, hope I will not lose any data.
Please help me out.
Related
This is my aunt's phone I'm trying to fix. From my understanding, the reason the dm-verity verification fail is occurring is because it had TWRP (which uses dm-verity). And I should be able to flash TWRP to fix it, but since it has the FRP lock on, I can't flash it (custom binary blocked when I try to odin flash). Shouldn't be an issue since I have the email and password associated with the phone, but since the dm-verity fail is preventing the phone from properly booting, I can't do anything.
Just to make it easier to understand
What should fix the phone
- Flash TWRP (so I can flash a custom ROM/kernel)
- Login with the FRP associated account
Problems
- Can't odin flash TWRP because of FRP
- Can't fix FRP because phone won't login because of dm-verity
I've already tried flashing the stock firmware multiple times via ODIN, Kies, and Smart Switch. And I've also tried flashing only the kernel, but the FRP prevents that from going through.
Like I said, I have the account login info associated with the phone, so if there's a way to remotely disable the FRP, that'd be great. Thanks for the help!
Use the original usb cable and use Smartswitch recovery, on the back is your serial number you need. And then keep on trying in Smartswitch, it took me a while but it worked and could restore my S6 to stock. And fixed Knox and the FRP lock. And I also tried everything but Smartswitch recovery saved my phone.
Sent from my SM-G928F using XDA-Developers mobile app
SOLVED
Hello, I after countless attempts with firmware that seemed to stock it did not work I SOLVED downloading the firmware directly from the Samsung server using "SAMFIRM" and then flash it with ODIN.
https://forum.xda-developers.com/galaxy-tab-s/general/tool-samfirm-samsung-firmware-t2988647
CrazyTechnoBoy said:
This is my aunt's phone I'm trying to fix. From my understanding, the reason the dm-verity verification fail is occurring is because it had TWRP (which uses dm-verity). And I should be able to flash TWRP to fix it, but since it has the FRP lock on, I can't flash it (custom binary blocked when I try to odin flash). Shouldn't be an issue since I have the email and password associated with the phone, but since the dm-verity fail is preventing the phone from properly booting, I can't do anything.
Just to make it easier to understand
What should fix the phone
- Flash TWRP (so I can flash a custom ROM/kernel)
- Login with the FRP associated account
Problems
- Can't odin flash TWRP because of FRP
- Can't fix FRP because phone won't login because of dm-verity
I've already tried flashing the stock firmware multiple times via ODIN, Kies, and Smart Switch. And I've also tried flashing only the kernel, but the FRP prevents that from going through.
Like I said, I have the account login info associated with the phone, so if there's a way to remotely disable the FRP, that'd be great. Thanks for the help!
Click to expand...
Click to collapse
HI, i just have the same issue .
Have you found the solution?
tried everything.
Hopefully you can help
Just found myself here. My perfectly working S7 Edge Nougat now has frp on and do-verity.
vooks said:
Just found myself here. My perfectly working S7 Edge Nougat now has frp on and do-verity.
Click to expand...
Click to collapse
nazreen nasaruddin said:
HI, i just have the same issue .
Have you found the solution?
tried everything.
Hopefully you can help
Click to expand...
Click to collapse
Here's the thing. I had a guy help me fix the FRP problem. And even he had some trouble doing so. And this was done last year, so I only kind of remember how he helped fixed it and I can't guarantee your guys' issue will be fixed if you follow my steps. And you guys may have to know the email and password associated with the phone. I took care of the dm-verity issue on my own afterwards.
Again, I THINK these steps may work, so please don't get mad if these steps don't work. if you guys can, try to flash TWRP or a custom kernel (via ODIN). I know you guys may be having the same problem, but try it out first. If you can't, try finding a combination file for your device (yes, combination file. On Google, search for "[model number] combination file" and download it). Afterwards, flash it to your phone via ODIN. This will allow the phone to boot up, but it's functionality will be very limited. Now, I think this is where you'll be able to login to Google in the settings and the FRP problem will be fixed, IIRC. If you can't login or don't have the details, there's not really much more I can help out with since I believe this is what fixed my problem (really fuzzy memory, sorry). Try rebooting and flashing TWRP again. The combination file itself may have fixed the issue.
If the above fixed the frp problem, GREAT! You should now be able to flash TWRP via ODIN. When you flash TWRP, the dm-verity problem should be fixed, as well. But now your phone needs a ROM and custom kernel. So now find the ones you want. Your phone should be working now!
If for whatever reason your phone still won't work, let me know. I may have another solution.
CrazyTechnoBoy said:
This is my aunt's phone I'm trying to fix. From my understanding, the reason the dm-verity verification fail is occurring is because it had TWRP (which uses dm-verity). And I should be able to flash TWRP to fix it, but since it has the FRP lock on, I can't flash it (custom binary blocked when I try to odin flash). Shouldn't be an issue since I have the email and password associated with the phone, but since the dm-verity fail is preventing the phone from properly booting, I can't do anything.
Just to make it easier to understand
What should fix the phone
- Flash TWRP (so I can flash a custom ROM/kernel)
- Login with the FRP associated account
Problems
- Can't odin flash TWRP because of FRP
- Can't fix FRP because phone won't login because of dm-verity
I've already tried flashing the stock firmware multiple times via ODIN, Kies, and Smart Switch. And I've also tried flashing only the kernel, but the FRP prevents that from going through.
Like I said, I have the account login info associated with the phone, so if there's a way to remotely disable the FRP, that'd be great. Thanks for the help!
Click to expand...
Click to collapse
Dont try to flash a zip you downloaded. Connect to smart switch and tell it to restore the phone. It downloads the right firmware for you.
godkingofcanada said:
Dont try to flash a zip you downloaded. Connect to smart switch and tell it to restore the phone. It downloads the right firmware for you.
Click to expand...
Click to collapse
Naa. I did that. Plenty of times. It simply didn't work. Lol. By saying I tried flashing the stock firmware via Smart Switch, I meant I let Smart Switch do its work. It might work if you only had one issue or the other, but if you have both FRP and dm-verity isses, it probably won't work.
CrazyTechnoBoy said:
Naa. I did that. Plenty of times. It simply didn't work. Lol. By saying I tried flashing the stock firmware via Smart Switch, I meant I let Smart Switch do its work. It might work if you only had one issue or the other, but if you have both FRP and dm-verity isses, it probably won't work.
Click to expand...
Click to collapse
you make me calm, cause i think combination file will save my phone which also i encountering the same like what you encountered before. and now i've read this post that you solved by flashing the combination file. i'm still waiting for my combination file cause i have binary 5 official rom while the combination files that i found is binary 4.
thanks!
Hello fellow people of XDA!
Today I got an OTA update for my S7 edge (SM-G935F). The update has installed fairly fast (after the first reboot). But then, it got stuck on a decrypting loop. I have enabled prior the full phone encryption, and set it to ask for a password at each start. I entered the password correctly, as it said Starting Android... after, and since then, only the rotating padlock is showing. Every like 5 minutes the soft buttons are lighting up for a second, but then nothing is happening. After a while it even gets hot, but still nothing. I had this issue at the previous update too, but it started after like 30-40 minutes. Now 90 minutes have passed and still nothing.
I can reboot to the recovery and bootloader screens, and everything is fine. Knox not tripped, not rooted, everything official. In the recovery screen it says that my CSC is ECT (but according to sammobile it should be CNX).
Some additional info: samsung/hero2ltexx/hero2lte
7.0/NRD90M/G935FXXU2DRAG
I will try to flash a stock rom (PDA: G935FXXS2DRAA, CSC: G935FROM1DQJ3). If that doesn't work, I'll flash today's rom (PDA: same, CSC: G935FVFG1DQI1).
Any tips/help would be greately appreciated! Would not want to fall to the wipe data method, because I don't want to lose everything... But then again, I guess that would remove the boot password...
Thanks!
Update: After waiting for like 10+ hours, nothing has changed. Maybe I shouldn't have forced a reboot after an hour of the ota update? Going to try flashing the firmware now.
Update 2: I flashed the firmware, now the buttons seem to light up less often. But after an hour of decrypting, I guess the ultimate soultion would be to do a factory reset, since no one is helping...
jaszfalvi.tamas said:
Hello fellow people of XDA!
Today I got an OTA update for my S7 edge (SM-G935F). The update has installed fairly fast (after the first reboot). But then, it got stuck on a decrypting loop. I have enabled prior the full phone encryption, and set it to ask for a password at each start. I entered the password correctly, as it said Starting Android... after, and since then, only the rotating padlock is showing. Every like 5 minutes the soft buttons are lighting up for a second, but then nothing is happening. After a while it even gets hot, but still nothing. I had this issue at the previous update too, but it started after like 30-40 minutes. Now 90 minutes have passed and still nothing.
I can reboot to the recovery and bootloader screens, and everything is fine. Knox not tripped, not rooted, everything official. In the recovery screen it says that my CSC is ECT (but according to sammobile it should be CNX).
Some additional info: samsung/hero2ltexx/hero2lte
7.0/NRD90M/G935FXXU2DRAG
I will try to flash a stock rom (PDA: G935FXXS2DRAA, CSC: G935FROM1DQJ3). If that doesn't work, I'll flash today's rom (PDA: same, CSC: G935FVFG1DQI1).
Any tips/help would be greately appreciated! Would not want to fall to the wipe data method, because I don't want to lose everything... But then again, I guess that would remove the boot password...
Thanks!
Update: After waiting for like 10+ hours, nothing has changed. Maybe I shouldn't have forced a reboot after an hour of the ota update? Going to try flashing the firmware now.
Update 2: I flashed the firmware, now the buttons seem to light up less often. But after an hour of decrypting, I guess the ultimate soultion would be to do a factory reset, since no one is helping...
Click to expand...
Click to collapse
Wait, i dont get it, it is prompting you for a password even you didnt set it?
Sent from my S7 Edge using XDA Labs
shah22 said:
Wait, i dont get it, it is prompting you for a password even you didnt set it?
Sent from my S7 Edge using XDA Labs
Click to expand...
Click to collapse
I set a password when I enabled Secure Startup.
jaszfalvi.tamas said:
I set a password when I enabled Secure Startup.
Click to expand...
Click to collapse
Then use that same password, i think there is confusion, there is a password when you enable fingerprint and then a password when you enable secure startup. Be sure not to confuse them. If it still happens, then I guess there's got something wrong with the update, and only way is a factory reset. Btw, i also updated and i normally entered secure boot password and it started okay. Don't know what caused this for you.
Sent from my S7 Edge using XDA Labs
shah22 said:
Then use that same password, i think there is confusion, there is a password when you enable fingerprint and then a password when you enable secure startup. Be sure not to remember them. If it still happens, then I guess there got something wrong with the update, and only way is a factory reset. Btw, i also updated and i normally entered secure boot password and it started okay. Don't know what caused this for you.
Sent from my S7 Edge using XDA Labs
Click to expand...
Click to collapse
I entered the password correctly, as it stated "Starting Android..." then the rotating padlock took forever. More than 10 hours even. But in the end, a factory reset helped me. But rip my photos and memories...
Don't use device encryption anymore and leave OEM unlocking enabled in developer options.
Those two settings cause more hassle if you want to keep data, and make backups from time to time using Samsung Smart switch on computer. Use a microSD card to store and take all your photos from camera.
benjamen50 said:
Don't use device encryption anymore and leave OEM unlocking enabled in developer options.
Those two settings cause more hassle if you want to keep data, and make backups from time to time using Samsung Smart switch on computer. Use a microSD card to store and take all your photos from camera.
Click to expand...
Click to collapse
Right, but i use encryption and i could update without any problem, don't know what caused this issue with him. But one should backup all data BEFORE updating, as i did to save yourself from such hassle.
Sent from my S7 Edge using XDA Labs
benjamen50 said:
Don't use device encryption anymore and leave OEM unlocking enabled in developer options.
Those two settings cause more hassle if you want to keep data, and make backups from time to time using Samsung Smart switch on computer. Use a microSD card to store and take all your photos from camera.
Click to expand...
Click to collapse
Yeah, it's a sure thing I won't turn on Secure Stratup anymore. I don't know what OEM unlock does or does not, but right now, I don't have dev options enabled. If I had a microSD then I couldn't care less about resetting my phone, but since I don't have, because I have two SIM cards and a memory card has no place left, I feel bad.
Still, I don't know caused this issue. I had OTA updates before with full device encryption enabled and I had no issues before. I kinda used the same disk space at every OTA, so it should have took the same time... And I have to mention, that I did not tamper with the software. No root, no custom rom, and software only from the play store.
To enable developer options you click Build number 7 times which is located in the Software information tab in settings.
OEM unlock allows you to flash and boot the phone with custom binaries (Custom Recovery, Kernels, Roms). You can leave OEM unlock disabled if you don't want people that may steal your phone and use it for themselves.
With OEM unlock disabled and a google account signed in, it will block anyone from using the phone after a factory reset on stock Samsung firmware as it will prompt the user to enter the google account that was associated with that device.
Unfortunately there are rare cases that a OTA update may fail. Reflashing correct stock firmware usually fixes it but in worse case scenarios a factory reset will be required.
benjamen50 said:
To enable developer options you click Build number 7 times which is located in the Software information tab in settings.
OEM unlock allows you to flash and boot the phone with custom binaries (Custom Recovery, Kernels, Roms). You can leave OEM unlock disabled if you don't want people that may steal your phone and use it for themselves.
With OEM unlock disabled and a google account signed in, it will block anyone from using the phone after a factory reset on stock Samsung firmware as it will prompt the user to enter the google account that was associated with that device.
Unfortunately there are rare cases that a OTA update may fail. Reflashing correct stock firmware usually fixes it but in worse case scenarios a factory reset will be required.
Click to expand...
Click to collapse
Never had OEM unlock enabled, because I didn't know what is does, so thanks for the info. I reflashed the correct stock firmware, but that didn't help either, so I had to resort to wiping the data... Regarding this, do you know by any chance a good software for recovering data without root?
I don't know of any unfortunately, if anyone has any good paid ones that actually work please post here.
I want to know that if my Mi A1 is unrooted with no recovery installed, bootloader unlocked and start up pin applied What are the chances that someone(thief) can reinstall rom on it and use it again. I am curious as to whether Android can be as theft proof as apple.?
Extract user data - no, reflash rom and start using the phone - yes (FRP bypass or EDL flash).
_mysiak_ said:
Extract user data - no, reflash rom and start using the phone - yes (FRP bypass or EDL flash).
Click to expand...
Click to collapse
Regarding EDL Flash I read this recent article (https://www.xda-developers.com/xiaomi-anti-rollback-protection-brick-phone/) and it mentions that only authorized service centres has EDL access. Read and share your opinion.
I think FRP bypass may be difficult if the security patch level is latest .
A query although I had reset my A1 several times by going in settings but didn't received the FRP message on Restart. Is it normal
pkrajpur said:
Regarding EDL Flash I read this recent article (https://www.xda-developers.com/xiaomi-anti-rollback-protection-brick-phone/) and it mentions that only authorized service centres has EDL access. Read and share your opinion.
I think FRP bypass may be difficult if the security patch level is latest .
A query although I had reset my A1 several times by going in settings but didn't received the FRP message on Restart. Is it normal
Click to expand...
Click to collapse
EDL mode has been locked for MIUI devices, but Android One can be flashed at home without major issues.
FRP protection is triggered when you perform factory reset from recovery. If you do it from settings, it is assumed that you are the owner of the device. With the existing implementation of FRP, I would not rely on its safety.
It seems that you are not worried about your data safety, so wondering why does it bother you if a thief can use the phone or not..? You have to buy a new one anyway..
_mysiak_ said:
EDL mode has been locked for MIUI devices, but Android One can be flashed at home without major issues.
FRP protection is triggered when you perform factory reset from recovery. If you do it from settings, it is assumed that you are the owner of the device. With the existing implementation of FRP, I would not rely on its safety.
It seems that you are not worried about your data safety, so wondering why does it bother you if a thief can use the phone or not..? You have to buy a new one anyway..
Click to expand...
Click to collapse
Just Curious. Thanks BTW :good:
Hi. My cousin asked me to root his SM-G531F and flash custom ROM to it. So, I come to him and tired to flash TWRP, just like I did on my SM-G350. But there's a problem - flashing fails, and there's a message "Custom image (recovery) blocked by FRP lock" or something like that. We rebooted (by taking battery of) phone and checked "OEM unlock" in dev settings. Tired to flash again - same message. IDK what more can we do. I don't want to brick his phone.
Also, when I searched for "FRP lock" there were no problem like ours, but lots of devices in bootloop with this message AFTER sucessful flash of custom ROM... That make me think about this all the day. I NEVER eccountered problem like that, but I never had so new phone, only old and easy-flashable ones. Is FRP lock dangerous? Do I need to do something to not brick his phone?
I found two types of slimiar looking locks - FAP lock and FRP one. Mine is rather FRP, I think I can read. What they really are and how they differ?
grzesiek11 said:
Hi. My cousin asked me to root his SM-G531F and flash custom ROM to it. So, I come to him and tired to flash TWRP, just like I did on my SM-G350. But there's a problem - flashing fails, and there's a message "Custom image (recovery) blocked by FRP lock" or something like that. We rebooted (by taking battery of) phone and checked "OEM unlock" in dev settings. Tired to flash again - same message. IDK what more can we do. I don't want to brick his phone.
Also, when I searched for "FRP lock" there were no problem like ours, but lots of devices in bootloop with this message AFTER sucessful flash of custom ROM... That make me think about this all the day. I NEVER eccountered problem like that, but I never had so new phone, only old and easy-flashable ones. Is FRP lock dangerous? Do I need to do something to not brick his phone?
I found two types of slimiar looking locks - FAP lock and FRP one. Mine is rather FRP, I think I can read. What they really are and how they differ?
Click to expand...
Click to collapse
FRP: https://www.samsung.com/us/support/frp/
FRP Just locks your phone if you alter the boot or recovery image and you had a google account registered. To unlock it you have to wipe data (factory reset) and reflash stock boot.img and recovery.img before using it again. If your cousin wants to flash my ROM (lineageos-13.0) he'd better not, its not stable and he will encouter random reboots and codecs bugs. The best thing to do is to remove FRP from his phone and flash Magisk (a root manager like SuperSU) and debloat it.
For more information, find the Grandprimevelte group on Telegram.
I think I'm having the exact same problem as OP, the thing is that when you flash twrp and the magisk on the phone with FRP disabled (no google account) it works just fine, but if you choose to add a google account to the device later you get a bootloop. If you try flashing with a google account logged in on the phone it doesn't let you (same as OP).
Is there any way to add a google account on the device after flashing twrp and magisk without enabling FRP lock? Thank you
RoiZerty said:
I think I'm having the exact same problem as OP, the thing is that when you flash twrp and the magisk on the phone with FRP disabled (no google account) it works just fine, but if you choose to add a google account to the device later you get a bootloop. If you try flashing with a google account logged in on the phone it doesn't let you (same as OP).
Is there any way to add a google account on the device after flashing twrp and magisk without enabling FRP lock? Thank you
Click to expand...
Click to collapse
Yes, you must install a boot.img without frp. Then you will be able to use a custom boot/recovery and root your phone without problem.
So long story short I was intoxicated and for some reason disabled OEM in debugging then sometime later I restarted my tablet to get the frp binary locked. It has a custom rom with twrp I absolutely need the data off of this tablet and the only way I see is to reinstall the default os through Odin but that wipes the device I need a method to get the data off of the tablet or a method to bypass frp entirely it would be mighty appreciated if I could have some help
Why don't you try a backup in TWRP?
Reinstalling the stock firmware with Odin won't wipe the device.
slop_me said:
So long story short I was intoxicated and for some reason disabled OEM in debugging then sometime later I restarted my tablet to get the frp binary locked. It has a custom rom with twrp I absolutely need the data off of this tablet and the only way I see is to reinstall the default os through Odin but that wipes the device I need a method to get the data off of the tablet or a method to bypass frp entirely it would be mighty appreciated if I could have some help
Click to expand...
Click to collapse
It's difficult to say if you can keep your data. The binary FRP lock is quite different that the average FRP lock that's associated with the Google sign in. Usually whenever you trip the binary lock it's because some firmware was installed such as a Root or a ROM that was flawed or invalid. It's an overstacking of binaries and therefore you get a "Custom Binaries Blocked by FRP Lock" notification. I've had this problem on another varient of the Tab A, the Galaxy Tab A6 SM-T580. I have found about four diferent variations of this. You may not have turned off OEM because in Binary lock it will act like you have. Possible reason to think that is the way it acts in Download Mode where you can't seem to flash anything especially the official firmware. Sound familiar?
Version 1. If you try to go to Recovery you get redirected to a screen similar to the Download Mode. In the upper left are red lettered "Custom Binaries Blocked by FRP Lock.. Download Mode is accessable but won't initialize when trying to flash stock firmware. Binary 4 FRP Unlock file was accepted and flashed in by Odin3. Stock firmware installs afterwards.
Version 2. Device is stuck in bootloop. "Custom Binaries Blocked by FRP Lock" appears on Logo screen. Recovery and Download Modes are so far, useless. Binary 4 FRP Unlock used, no positive results. Binary U 4 used. Positive result. Stock firmware flashed in afterwards.
Version 3. "Custom Binaries Blocked by FRP Lock" appears on Download Mode which either stalls right after or fails to initialize. Binary 4 FRP Unlock and Binary U 4 yeild no positive results. (This ones on it's way to me).
Version 4. "Custom Binaries Blocked by FRP Lock appears on Recovery Mode. Download Mode useless. I'm currently following this one.
Solution: I don't know if the one I have will work, they may be device specific. Research for a "SM-T280 Binary 4 FRP Unlock" which I couldn't yet find.
Casper Young said:
It's difficult to say if you can keep your data. The binary FRP lock is quite different that the average FRP lock that's associated with the Google sign in. Usually whenever you trip the binary lock it's because some firmware was installed such as a Root or a ROM that was flawed or invalid. It's an overstacking of binaries and therefore you get a "Custom Binaries Blocked by FRP Lock" notification. I've had this problem on another varient of the Tab A, the Galaxy Tab A6 SM-T580. I have found about four diferent variations of this. You may not have turned off OEM because in Binary lock it will act like you have. Possible reason to think that is the way it acts in Download Mode where you can't seem to flash anything especially the official firmware. Sound familiar?
Version 1. If you try to go to Recovery you get redirected to a screen similar to the Download Mode. In the upper left are red lettered "Custom Binaries Blocked by FRP Lock..
Solution: I don't know if the one I have will work, they may be device specific. Research for a "SM-T280 Binary 4 FRP Unlock"
But I couldn't find one.
Here's my post, it may help.
https://forum.xda-developers.com/general/help/custom-binary-blocked-frp-lock-2019-t3979661
Click to expand...
Click to collapse
Nothing needs to be done except install the stock firmware.
The device hasn't been reset so no need for any kind of bypass.
FRP has kicked in purely because unsigned software is installed.
Replace the unsigned software with stock and it'll boot just fine. Data fully intact.
ashyx said:
Nothing needs to be done except install the stock firmware.
The device hasn't been reset so no need for any kind of bypass.
FRP has kicked in purely because unsigned software is installed.
Replace the unsigned software with stock and it'll boot just fine. Data fully intact.
Click to expand...
Click to collapse
I hate to argue with you but that wasn't so easy with mine. While in Binary FRP lock I, along with a few others that have the SM-T580 or the SM-T585 couldn't use Download Mode to flash in the official stock firmware. Trial and error followed. The solve was first I had to flash in the Binary FRP Unlock and then I could flash in the firmware. With another device the owner tried the Binary Frp Unlock which didn't fix it. Later he flashed in the U4 Binary and that worked for him. I passed the info along to some others in the same predicament and it helped them. So I don't know what to tell you but what you're stating is not always applicable.
Casper Young said:
I hate to argue with you but that wasn't so easy with mine. While in Binary FRP lock I, along with a few others that have the SM-T580 or the SM-T585 couldn't use Download Mode to flash in the official stock firmware. Trial and error followed. The solve was first I had to flash in the Binary FRP Unlock and then I could flash in the firmware. With another device the owner tried the Binary Frp Unlock which didn't fix it. Later he flashed in the U4 Binary and that worked for him. I passed the info along to some others in the same predicament and it helped them. So I don't know what to tell you but what you're stating is not always applicable.
Click to expand...
Click to collapse
Trust me, I have 3 of these devices. I've bricked them, frp locked them every possible way during development for this device.
The T580 is a different device and may be more difficult to bypass if and only if FRP has kicked in because of a device reset.
However for EVERY Samsung device that has simply had non stock software installed the only fix that's required is to install the stock firmware.
This is the case on all the Samsung devices I own and I have quite a few from lollipop to Pie.
ashyx said:
Trust me, [not happening!]I have 3 of these devices. I've bricked them, frp locked them every possible way during development for this device. [Well, umm. No, you haven't. And take a wild guess how many devices I have, like that matters.]
The T580 is a different device and may be more difficult to bypass if and only if FRP has kicked in because of a device reset. [Everytime you turn off the device it resets.]
However for EVERY Samsung device that has simply had non stock software installed the only fix that's required is to install the stock firmware. [You obviously have difficulties comprehending that I said otherwise]
This is the case on all the Samsung devices I own and I have quite a few from lollipop to Pie.
Click to expand...
Click to collapse
Wow, you're on a roll ain't ya? Hey ASHYX, dont misjudge me because of my stats you see here. Over a decade ago I was stacking ROMs into my HTC-G1. 3 decades ago I was an Electrical Engineer and Sonar Operator in the Navy. Let me tell you point blank, you're mistaken! Normally you would think you can just flash in stock OTA firmware into the device via Odin3 and you get to return to normal. Well that wasn't the solve for this. This was a new one to me also. If you think you're so right on what you say I'll be more than happy to point you in the direction of some XDA visitors, two of which are still Binary FRP locked. You can try telling them what you just told me and they'll probably call you a blooming idiot. No offense but you could try reading it properly which might help.
I said, [QOUTE] " While in Binary FRP lock I, along with a few others that have the SM-T580 or the SM-T585 couldn't use Download Mode to flash in the official stock firmware. [END QOUTE]
Take my word for it, the method you stated was already tried AND DID NOT WORK!
If you want to insist you're all that, here ya go, these people need your expertise in development
https://forum.xda-developers.com/ga...frp-locked-t3772512/post80420061#post80420061
Data loss when flashing stock firmware.
ashyx said:
Reinstalling the stock firmware with Odin won't wipe the device.
Click to expand...
Click to collapse
That depends on which stock firmware you're using. Typically what you get OTA (over the air) is the same as the 4File Official Stock Firmware. These are the 4 files that go into each section when using Odin3 to flash firmware. BL is for the Bootloader which controls security, start-up and recovery. AP is Android Partitioning, CP is Cellular Processor. Now let's talk about the CSC. file. The 4File contains two CSC files, one is listed as HOME CSC. If you flash the CSC file you will lose your App data. If you flash the HOME CSC you do not lose your App data.
Casper Young said:
That depends on which stock firmware you're using. Typically what you get OTA (over the air) is the same as the 4File Official Stock Firmware. These are the 4 files that go into each section when using Odin3 to flash firmware. BL is for the Bootloader which controls security, start-up and recovery. AP is Android Partitioning, CP is Cellular Processor. Now let's talk about the CSC. file. The 4File contains two CSC files, one is listed as HOME CSC. If you flash the CSC file you will lose your App data. If you flash the HOME CSC you do not lose your App data.
Click to expand...
Click to collapse
ashyx said:
Nothing needs to be done except install the stock firmware.
The device hasn't been reset so no need for any kind of bypass.
FRP has kicked in purely because unsigned software is installed.
Replace the unsigned software with stock and it'll boot just fine. Data fully intact.
Click to expand...
Click to collapse
Thank you for confirming I won't loss any data upon installing the original ROM I did just have a custom ROM installed I was super concerned that I would lose all the data upon installing the original ROM thank you so much <3
slop_me said:
Thank you for confirming I won't loss any data upon installing the original ROM I did just have a custom ROM installed I was super concerned that I would lose all the data upon installing the original ROM thank you so much <3
Click to expand...
Click to collapse
Depends on which custom rom you had installed? If it's stock based on lollipop then you should be fine. If its lineage then it may not boot without a data wipe.
ashyx said:
Depends on which custom rom you had installed? If it's stock based on lollipop then you should be fine. If its lineage then it may not boot without a data wipe.
Click to expand...
Click to collapse
Yeah it was just stock lollipop with a root. Will that cause an issue or am I good to continue?
ashyx said:
Depends on which custom rom you had installed? If it's stock based on lollipop then you should be fine. If its lineage then it may not boot without a data wipe.
Click to expand...
Click to collapse
Props to you thanks for the knowledge it worked flawlessly I mean kinda half way through it did say erasing and I kinda **** the bed and got scared because I really needed the data off of there but my man you are right just flashing stock ROM worked flawlessly everywhere online says it will wipe the device but it didn't. Thank you so much for your fantastic help <3