S7 EDGE bricked or hardware failure? - Samsung Galaxy S7 Edge Questions and Answers

My S7 edge had been acting weirdly for a few weeks, things like random restarts once a few days so I didn't pay much attention and over excessively heating up to 50/55 degrees (I usually checked the temperature through CPU_Z), and just a few hours ago I ran into problems like the phone restarting on its own, never getting past the samsung logo on boot, so I did the normal thing everyone else would do and just factory reset the device through recovery mode, a point to add here the device took an absolute age to load into recovery mode, this wasn't a case of bad key combination or anything like that, the device would load this the dmverity tree hash verification thing and sit there for a good 2-3 mins which is unusual, same thing happens with factory reset takes an absolute age and comes back with the following text-:
"E: format_volume: make ext4 failed on /dev/block/platform/155a0000.ufs/by-name/USERDATA with 1(I/O error)
-- Set Factory Reset done...
Data wipe failed."
booting up the device in this state would show up with an error "Device storage corrupt" with a " reset device" button in the bottom of the screen which didn't respond to any touches which was weird as well because holding the power button and then selecting the power off option worked with no issues so it wasn't an issue with the touchscreen.
searching for a solution on google led me to flash a official firmware that I downloaded from updato, just a heads up my device has never been tampered with or had any kind of software modifications this includes flashing any roms or even official firmwares before, so I download the firmware and flashed it as usual this is the firmware that I flashed through odin 3.12.3 firmware version was G935FOJV1DQAV also my device model is SM-G935FD while the firmware I flashed was for SM-G935F but this shouldn't be an issue because when I usually got updates over the air on the device they would be for SM-G935F so if there were any issues with this they should have popped up a long time ago, so everything went smoothly and the phone booted up again as usual, did the initial setup and adding accounts, recovery everything, hooked up the charger and left the phone to download all the necessary stuff through samsung and google cloud recovery, comeback after a few minutes to find that the device just wouldn't respond to the power button or the home button to wake the device up but the led on the phone was flashing in blue color which means I did receive some notifications, so I hard reset the phone by holding down power+volume down key, same issues pop up like before the firmware I flashed getting stuck on the boot samsung logo, went back to recovery to do another factory reset again it keeps freezing on the dm-verity tree hash thing, but this time the factory reset happens properly with no errors, but the device doesn't boot up at all, gets stuck on the samsung logo and the led on top starts flashing in several different colors, just like when you boot up a brand new S7 edge.
As a last ditch effort I try initializing the device through smart switch, everything goes normally but when the flashing process starts it gets stuck on 7% indefinitely, tried everything else but to no avail, tried flashing through odin again but it gets stuck on the same point as smart switch, tried installing the firmware in parts through odin again gets stuck on the same point when flashing AP but other parts get installed without any problems, download mode boots up fine, recovery mode now boots up very slowly with a dm-verity error "E:failed to mount / system (invalid argument).
I have 1 month warranty left on my S7 edge from where I purchased it, I want to send it back for a refund or a replacement but the only thing thats kind of worrying me is that in download mode the knox switch hasn't been tripped still shows 0 (0*000), but shows system status as custom, will this effect my warranty claim if they check my device?

TreekoX said:
My S7 edge had been acting weirdly for a few weeks, things like random restarts once a few days so I didn't pay much attention and over excessively heating up to 50/55 degrees (I usually checked the temperature through CPU_Z), and just a few hours ago I ran into problems like the phone restarting on its own, never getting past the samsung logo on boot, so I did the normal thing everyone else would do and just factory reset the device through recovery mode, a point to add here the device took an absolute age to load into recovery mode, this wasn't a case of bad key combination or anything like that, the device would load this the dmverity tree hash verification thing and sit there for a good 2-3 mins which is unusual, same thing happens with factory reset takes an absolute age and comes back with the following text-:
"E: format_volume: make ext4 failed on /dev/block/platform/155a0000.ufs/by-name/USERDATA with 1(I/O error)
-- Set Factory Reset done...
Data wipe failed."
booting up the device in this state would show up with an error "Device storage corrupt" with a " reset device" button in the bottom of the screen which didn't respond to any touches which was weird as well because holding the power button and then selecting the power off option worked with no issues so it wasn't an issue with the touchscreen.
searching for a solution on google led me to flash a official firmware that I downloaded from updato, just a heads up my device has never been tampered with or had any kind of software modifications this includes flashing any roms or even official firmwares before, so I download the firmware and flashed it as usual this is the firmware that I flashed through odin 3.12.3 firmware version was G935FOJV1DQAV also my device model is SM-G935FD while the firmware I flashed was for SM-G935F but this shouldn't be an issue because when I usually got updates over the air on the device they would be for SM-G935F so if there were any issues with this they should have popped up a long time ago, so everything went smoothly and the phone booted up again as usual, did the initial setup and adding accounts, recovery everything, hooked up the charger and left the phone to download all the necessary stuff through samsung and google cloud recovery, comeback after a few minutes to find that the device just wouldn't respond to the power button or the home button to wake the device up but the led on the phone was flashing in blue color which means I did receive some notifications, so I hard reset the phone by holding down power+volume down key, same issues pop up like before the firmware I flashed getting stuck on the boot samsung logo, went back to recovery to do another factory reset again it keeps freezing on the dm-verity tree hash thing, but this time the factory reset happens properly with no errors, but the device doesn't boot up at all, gets stuck on the samsung logo and the led on top starts flashing in several different colors, just like when you boot up a brand new S7 edge.
As a last ditch effort I try initializing the device through smart switch, everything goes normally but when the flashing process starts it gets stuck on 7% indefinitely, tried everything else but to no avail, tried flashing through odin again but it gets stuck on the same point as smart switch, tried installing the firmware in parts through odin again gets stuck on the same point when flashing AP but other parts get installed without any problems, download mode boots up fine, recovery mode now boots up very slowly with a dm-verity error "E:failed to mount / system (invalid argument).
I have 1 month warranty left on my S7 edge from where I purchased it, I want to send it back for a refund or a replacement but the only thing thats kind of worrying me is that in download mode the knox switch hasn't been tripped still shows 0 (0*000), but shows system status as custom, will this effect my warranty claim if they check my device?
Click to expand...
Click to collapse
Having the same issue. anyone help? did you manage to solve this issue?

Related

Sm-g900f (uk) galaxy s5 - arrgghhhhh

Can anyone PLEASE help??
My partner opted to do a suggested update on her S5, but didn't notice the wifi was off. The phone seemed to have done the update, but shortly after it rebooted itself, then again, then again. The frequency of reboot got quicker and quicker and now it loops between the Galaxy S5 splash screen and the SAMSUNG logo, but doesn't go any further.
I managed to boot the phone into reset mode, cleared the cache and then did a factory reset, but that did nothing to prevent the boot loop.
I then downloaded Odin (ver 10.3.7) and what I believed to be the correct firmware (G900FXXS1CPLV_G900FVFR1CPJ1_G900FXXU1CPIW_HOME.tar.md5).
Having checked the battery was charged, I followed the instructions of connecting the phone via USB, loading the md5 in the AP, checking Auto Reboot and F-Set time in the options and clicking the Odin Start button. I had removed the battery, replaced it and then booted it into the update mode (Power, Home, Volume Down, then volume up) with the screen confirming I was in the right place (....do not unplug.... etc).
The file loaded, (green bar at top of the Odin window on my PC) and Odin reported success. I then disconnected the phone, booted in recovery mode, reset the cache and then did a clear data, factory reset.
The same symptoms prevail, STUCK IN BOOT LOOP!!!!
The only thing different is that if I plug it into the USB on my PC, after a while the phone tries to turn itself on and goes into either a boot loop or freezes on the Galaxy S5 Splash screen or the SAMSUNG Logo.
I am charging another battery (just in case that is in some way to blame) and will try again to replace the firmware, but could I be missing something, do I need to do anything with PIT (I thought this was all taken care of by Odin using the MD5 file) or is there some other test I can perform that will show if the phone is fried???
MANY THANKS for looking!
ur going correct, try to reflash it again through odin and dont disconnect phone until it boots into system, it is taking some good time, so just wait and dont do anything this time like clearing anything or restoring. i hope ull get success.
THANKS - but...
Thanks Rayzen, I will try the whole thing again, but I think there is something more to this than a firmware fault!
There and gone again
OK, so on the 4th attempt I got the phone to take the firmware using Odin, it reported success and the phone rebooted itself (several times) and eventually appeared to boot to a new factory reset.
I put in a SIM card and entered my email and google account details and left it charging over night. This morning when I tried to use it, the screen froze and then it rebooted itself. Hey presto, the phone is back to square one with a boot loop.
ANYONE (please) got any suggestions?
THANKS
No one??
same here, same symptoms, same feeling.
when flash gone right... i feel lucky.. but for half hour only, rebooted and angain in boot loop.
I cannot even boot in recovery. flashed TWRP. from 5 boots in recovery only 1 success.
When trying to wipe phone in TWRP - it hangs.
still trying to install some other (custom) rom. still no success.
hope never dies
same things happened here! now cant get samsung galaxy s5 to boot...............
Are you sure your using right firmware? as it took me a few versions before it booted last time this happened?
Could any please confirm what is the right firmware for samsung galaxy s5 900F
It took another 6 or 7 attempts, left it over night and was about to trash it when it booted.
I then received a 'software update available' message and tried installing it. First attempt put the phone back into boot loop so I reflashed it again using Odin.
That worked immediately the over the network software update installed and now phone is 100%
Very frustrating but I got there!
glad you fixed it! ive tried three different firmwares and still nothing.
trying this one atm
G900FXXU1ANE2_G900FEVR1AND1_G900FXXU1ANE2_HOME.tar
oh and how long do they take to boot when there are sitting at the samsung glowing screen?>
I'm in UK and used what (I had to guess) was the best firmware.
I'll let you know which version it was when I get home tonight.
BUT I had all the problems with a single version and it eventually came good.
I read somewhere that overwriting a different core (from specific providers) with generic firmware, could lead to a world of pain until it gets full replaced... not sure if that's a good description (or has any fact to it) but it seemed to be re-loading and re-loading and re........ for ages, finally cracked it.
well mines booted now!but getting constant errors about samsung push!
If it'still booted, you'very made progress!
Push issues are mentioned elsewhere and can (eventually be sorted) but if you have a booted phone you should be able to get an over the air software update installed from the service provider....?!

Boot issue

I am having an issue booting my S7 Edge (US Unlocked)...thanks in advance for reading
Woke up in the middle of the night, checked a text, pull down menu froze screen, noticed battery at 1%...plugged in to charger
Next morning, black screen with solid blue notification light
Tried restarting several times with same result, but eventually it booted normally (one time)
Phone went back to same state...black screen, blue notification
Tried several restarts and eventually went to recovery mode...cleared cache, rebooted, no luck
Over the last day and a half I tried restarting many times with varying results
Always get "Rebooting Recovery...." on top of screen
Sometimes get Samsung Galaxy S7 Edge" screen, though most often not
Usually get the "Installing updates" screen, then "No Command"
Sometimes (rarely) I can get to recovery screen...though most often not
Sometimes in recovery screen I am frozen (volume buttons don't work for selection)
I can usually get into download mode
I've tried everything I can think of and find to get the phone to restart including letting the battery drain completely and doing a full recharge and restarting without SIM/SD
Any ideas on how I can get into my phone without a hard reset...i'd like to try and backup some files/texts first if at all possible. I haven't been able to get into safe mode
Any files I can load to SD or through ADB that would help?
Phone is stock...no rooting or roms (first time keeping a stock phone...go figure)
Thanks.
I've tried flashing stock firmware from updato and sammobile with no luck. Can never get past the "Recovery Booting...." screen. No help from smartswitch. Anything else I can try?
Having the same issue...
any help would be appreciated.
Tried flashing many times and got several different errors...often if failed on cache.img.ext4
I was able to flash BL + CP + CSC successfully, then flash AP successfully. Still had boot loop issues after that though, so not much progress.
Once I did get the "error...connect to smartswitch" screen, but smartswitch did not recognize device.
Not really sure where to go next from here.

Stuck on "Starting Android..."

Hi Guys
I used Odin to reflash my Galaxy S10+ dual sim (duos) as it was experiencing some slowness. I used the Singapore firmware as it uses the same "G975FXXU1ASBA" model name.
The process completed successfully but when the phone boots, it gets past the Samsung logo screen and then gets stuck on a blank black screen with "Starting Android..." showing in the middle. I can swipe down from the top to show the toolbar, but it is limited in what I can select from it and the phone doesn't get to the point where the home screen boots.
I'm guessing this could be an app optimization process but after 4 hours, it was still on this screen.
I've tried re-flashing (redownloading the firmware files), clearing the cache and rebooting the phone.
Does anyone have any ideas?
In case you do want to start clean anyway, have you tried doing a reset in the recovery menu (where you are wiping the cache)? This will wipe all data.
I may have to try the full wipe, which is something I wanted to avoid but seems I have no choice.
Hopefully that at least solves the problem.
I have the same problem but I cannot get it to boot into recovery or download mode. I was flashing Magisk at the time. Odin said it worked but now it wont pass the initial stating android... Odin detects the phone but can talk to it. ADB does not even detect the phone. Phone power and reset come on. if i hold both volume the assistant comes on and if i hold bixby the safemode tag appears in the bottom corner but it still wont boot past Starting Android or boot into download mode

Galaxy S8+ in bootloop without recovery and frp locked

Hi guys!
I've read tons of threads and guides on Google but nothing helped me to bring to life my Samsung Galaxy S8 Plus. After hours and hours of test and probes I surrender!
Basically I was using normally my phone and suddenly has power off and showing the Samsung Galaxy Logo continuously. I've force reboot it with vol down+pwr button and after some minutes restart normally again. After 5min again the boot loop and stuck there. Tried again to power it off but didn't work so I thought was the battery (because is 3yrs old with heavy use and months ago I had the screen flickering and a battery drain to zero). I opened the phone, unplug the battery and the power button (because I thought was the power button stucked as on my father phone). So after mounted all the stuff in their place I tried to boot it and suddenly start to work again! I've backup all my things rapidly but again power off by himself and this is the last time I see it working.
So I tried to empty the cache entering in the recovery but it was useless so the only way seems flashing the original FW with Odin. Downloaded the right one with Frija, upload the rights files in Odin (Home_csc because I don't want to lose my internal memory stuff) and the phone automatically reboots, pass the Samsung logo and go in Upgrading mode with the blue android screen and a % increasing. After that by himself power off and nothing happen.
I read some stuff about my possibilities to recover it without losing data but a lot of tutorial talk about entering in recovery but I cannot do it! Simply does not go in recovery with vol_up+bixby+pwr_button even after force shutdown it with vol_down+pwr_button or reattach the battery. The only thing I'm allowed to do is put it in Download Mode to be recognized by Odin.
I've tried to launch ADB devices but it is not visible in Download Mode.
I've tried to flash another firmware for the same model (theoretically my one is unbranded italian) but I tried with WIND one because in download mode there is a text "Carried_ID:WIND" but this FW Odin fail to upload it.
I've tried to flash the TWRP with Odin but fails on the phone with error "Custom binary(recovery) blocked by FRP Lock". I've searched how to unlock it but without have access to recovery or phone settings seems impossible. And this phone has also OEM Lock.
I've tried again to flash the FW but the only difference than before was the blue android robot with stucked text "Installing system update", "Erasing" , "yellow advice notice" and finally a green screen with "An error has occurred while updating the device software.Use the Emergency recovery function in the Smart Switch PC Software". And yes, I already tried with Smart Switch but the program does not detect the phone.
I've also tried to flash the original recovery but nothing change.
Seems that my devices is bricked or a kind of boot loop.
In my situation there is something that I can do to recover the internal memory data? I don't tried to flash the FW with CSC file because I don't want to erase all the data.
My Galaxy was original since the purchasing, no root or flashed a FW, only OTA updates.
I've attached a photo with the stuff that appear in Download mode.

Galaxy A3 (2016) can't boot up, no matter what

It's been a few months but it would either get stuck in the "Galaxy A36" screen or during the "SAMSUNG" screen and after some time just reboot itself on its own, like again and again. A single time it actually went into the OS but crashed after about 15 seconds and never did the same thing ever again. Since then it's been really unpredictable. Sometimes it turn on, sometimes it doesn't react, no matter what kind of buttons you push. Not being able to see the battery state doesn't help either.
Got this phone from a coworker. He's not the type of person to fiddle around with the system, so he didn't try to install a different firmware or anything. I can imagine something went wrong while updating (when did it last get an update though...) or while installing some kind of app or catching a virus. Or maybe the motherboard is just fried, that would be my guess actually.
So, what did i try next? Recovery mode... it seemed to be loading something and crashed shortly after. Next up i tried getting KIES and Smart Switch to work with it, but no response. Got the USB drivers atleast and ODIN connects with it. Tried flashing it with the original firmware. For some reason it failed the first couple of times (i've been reading battery has to be atleast 50% for it to work) but a day later after charging for long time it "worked" and shown me a green PASS. However it still didn't boot up, no matter how long i waited.
Tried recovery mode again but it just shows me a passed out Android man, lol. Tried booting up and sometimes got some messages in red like "Custom binary blocked by FRP lock" and "Recovery is not seandroid enforcing" whatever that means. I know ODIN has some more options, to wipe internals but i'd rather save everything on there. Running out of ideas here. Anyone?

Categories

Resources