Exit EDL Mode - ZTE Axon 7 Questions & Answers

I am now in EDL mode, I exit can't EDL mode

Hold power button for a little while...

Yes, just hold the power button down for about 10 seconds and it should boot. If not, then try holding it down for about 30 seconds instead. You should see the red LED blink just before it comes on.

does not exit edl mode
MI S2 MODEL M8103E6G
does not exit edl mode
phone cannot power on will boot to edl mode always.
please help.......:crying:

userfile said:
MI S2 MODEL M8103E6G
does not exit edl mode
phone cannot power on will boot to edl mode always.
please help.......:crying:
Click to expand...
Click to collapse
Wrong forum, aren't you able to read?

If you have some ROM that fits your cellphone just flash it. Worked for me in my Xiaomi Mi a3 using Miflash.
Good look.

Related

Only turn on in fastboot mode

My nexus 4 isn't turning on in any way.
If i connect the power cable a red light blink once and stop, pressing the power button nothing happens. The only way to get some activity it's pressing the volume down + power and connect the power cable, but turn on in the fastboot mode and can get out of there. If i try recovery mode the phone dies, if i try to reboot the phone dies, if try to normal boot the phone dies.
I can turn on in download mode, but the LGNPST don't recognize it.
Fastboot commands via prompt are fine, unless i need to do something that reboot the phone.
Someone can help me?
mtoledo62 said:
My nexus 4 isn't turning on in any way.
If i connect the power cable a red light blink once and stop, pressing the power button nothing happens. The only way to get some activity it's pressing the volume down + power and connect the power cable, but turn on in the fastboot mode and can get out of there. If i try recovery mode the phone dies, if i try to reboot the phone dies, if try to normal boot the phone dies.
I can turn on in download mode, but the LGNPST don't recognize it.
Fastboot commands via prompt are fine, unless i need to do something that reboot the phone.
Someone can help me?
Click to expand...
Click to collapse
Flash factory image via fastboot.
Nitin
sorry for delay to response, i think i found the problem: the battery

bricked axon 7

edl Does not work anroid6 I wanted FASTBOOT_UNLOCK_EDL flash Hit by mistake FASTBOOT_UNLOCK_EDL_N flash hit Smartphone Bright
But the screen is black And vibrates The red light stays And to the state does not go
[Power] + [Volume Up] + [Volume Down] Smartphone Riastart
The light of the cave is still bright
Thank you i'm sorry i wrote bad
turn off your phone.
press and hold vol up + and vol down at same time, and plug the phone into computer while holding.
From computer , check if there is something like 9008 port.
If there is, try flash full edl by following this post.
https://forum.xda-developers.com/axon-7/development/axon-7-edl-tool-flash-backup-restore-t3750759
llaalways said:
turn off your phone.
press and hold vol up + and vol down at same time, and plug the phone into computer while holding.
From computer , check if there is something like 9008 port.
If there is, try flash full edl by following this post.
https://forum.xda-developers.com/axon-7/development/axon-7-edl-tool-flash-backup-restore-t3750759
Click to expand...
Click to collapse
My friend is the phone edl identification Not to be The light of the phone remains bright
The phone is off the logo is not the black screen dfu Is known Friends please help me
hamidz 11 said:
My friend is the phone edl identification Not to be The light of the phone remains bright
The phone is off the logo is not the black screen dfu Is known Friends please help me
Click to expand...
Click to collapse
EDL is that. The phone seems off but it is NOT.

Samsung S5E keeps rebooting

I tried flashing the stock firmware via ODIN but the process failed and now my tablet is dead and not responding to power button + vol up/down, nothing happens.
When I hook up the tablet to the Samsung charger that can with it or my PC, the tablet boots into download mode and shows the "an error occurred while updating the device software" message and then starts after about 1 sec. It's been charging all night, so the battery should be 100%.
If I hold the vol up+down is shows the long press to unlock the bootloader for about 1sec then reboots.
Any help to force my tablet to stay on and a way to fix my issue ?
same thing happens with mine (after trying to flash firmware via odin)
reboots over and over without letting you stay in download mode
i have mine in edl mode
It maybe in a black screen of death. Either vol up or down and power for at least 10 seconds. I had this happen to me once.
ygchawki12 said:
i have mine in edl mode
Click to expand...
Click to collapse
how do we boot the tablet into EDL mode? shouldn't we be able to unbrick the phone if we're in EDL mode?

[HELP NEEDED] Dead S10+ (SM-G975F)

Hey guys, I have a little problem and could need some Help fixing my S10+ (G975F)
What did I do:
- Flashed latest TWRP from TWRP.me + vbmeta
What happened:
- My S10 was stuck in a endless bootloop at the S10 logo, didn't boot to download mode or TWRP and my PC didn't recognize it.
My problem now:
I let the phone in that bootloop over night to let the battery discharge. Next day when it was powered of I tried entering download mode by pressing volume down + bixby and connecting the cable to my pc but the screen was just staying black, after releasing the volume down and bixby key but keeping the cable connected it started with the bootloop again, so right now there i'm out of ideas, I just can't enter the download mode or TWRP.
Any help would be really appreciated.
Best regards, Jan
NPEv2 said:
Hey guys, I have a little problem and could need some Help fixing my S10+ (G975F)
What did I do:
- Flashed latest TWRP from TWRP.me + vbmeta
What happened:
- My S10 was stuck in a endless bootloop at the S10 logo, didn't boot to download mode or TWRP and my PC didn't recognize it.
My problem now:
I let the phone in that bootloop over night to let the battery discharge. Next day when it was powered of I tried entering download mode by pressing volume down + bixby and connecting the cable to my pc but the screen was just staying black, after releasing the volume down and bixby key but keeping the cable connected it started with the bootloop again, so right now there i'm out of ideas, I just can't enter the download mode or TWRP.
Any help would be really appreciated.
Best regards, Jan
Click to expand...
Click to collapse
Did you tried to enter recovery?
And BTW samsung download mode is super strong almost impossible to brick you aren't trying key combination correctly to enter download mode or recovery.
When phone is restarting to enter download mode
Just
Hold bixby, volume down and while holding these, put the usb-c cable in the s10+ when connected to the PC.
comsite said:
Did you tried to enter recovery?
And BTW samsung download mode is super strong almost impossible to brick you aren't trying key combination correctly to enter download mode or recovery.
When phone is restarting to enter download mode
Just
Hold bixby, volume down and while holding these, put the usb-c cable in the s10+ when connected to the PC.
Click to expand...
Click to collapse
Thanks for your reply, but as I described I tried everything from above, with different PCs and Cables.
comsite said:
Did you tried to enter recovery?
And BTW samsung download mode is super strong almost impossible to brick you aren't trying key combination correctly to enter download mode or recovery.
When phone is restarting to enter download mode
Just
Hold bixby, volume down and while holding these, put the usb-c cable in the s10+ when connected to the PC.
Click to expand...
Click to collapse
Also as recovery I flashed twrp from official site, which is unable to boot
Had same problem for download mode, in the end it worked with cable plugged into pc and phone held volume down bixby button then powered the phone on,went into download mode.
Sent from my SM-G975F using Tapatalk
lufc1953 said:
Had same problem for download mode, in the end it worked with cable plugged into pc and phone held volume down bixby button then powered the phone on,went into download mode.
Click to expand...
Click to collapse
If I press bixby and volume down while being connected to PC I just get a blackscreen
What happened when it went to black screen instead of download mode? I mean what its shows in pc?specifically in odin? While on black screen try tu press volume up and to proceed download mode even though there is black screen if then it shows in odin then you can flash stock.
Did you unlock boot loader before flashing twrp? Did you?
any update on that?

Cannot unbrick [cannot enter EDL mode]

Hoping someone can shed some light. Rushing to root phone again to send back warranty replacement, in my haste my laptop died mid flash and now can only boot in Fastboot and Crashdump Mode.
I am attempting to restore to factory via the MSM tool but cannot for the life of me enter EDL mode.
With phone powered off and pressing the vol up and down keys while plugging into the PC, it only enters Fastboot mode
I have tried to do it with phone off, rebooting from Crashdump mode, from fastboot and it seems that no combination allows me to do so.
I have also tried just vol up and vol down. App loaded at the flash screen, not loaded, etc.
Thanks in advance
quy said:
Hoping someone can shed some light. Rushing to root phone again to send back warranty replacement, in my haste my laptop died mid flash and now can only boot in Fastboot and Crashdump Mode.
I am attempting to restore to factory via the MSM tool but cannot for the life of me enter EDL mode.
With phone powered off and pressing the vol up and down keys while plugging into the PC, it only enters Fastboot mode
I have tried to do it with phone off, rebooting from Crashdump mode, from fastboot and it seems that no combination allows me to do so.
I have also tried just vol up and vol down. App loaded at the flash screen, not loaded, etc.
Thanks in advance
Click to expand...
Click to collapse
What I did when I was in Crash Dump Mode was,
Press and Hold Power Off and Volume Up button and release when the screen goes off. Now your phone is switched off. Now to enter the EDL mode you need to press and hold volume up and volume down buttons at the same time...and then connect the mobile to pc while still holding the buttons. Done. MSM tool will detect your phone.
NOTE : Also keep the Device Manager window open on the PC while u connect the phone to pc and check if it shows up there.
quy said:
Hoping someone can shed some light. Rushing to root phone again to send back warranty replacement, in my haste my laptop died mid flash and now can only boot in Fastboot and Crashdump Mode.
I am attempting to restore to factory via the MSM tool but cannot for the life of me enter EDL mode.
With phone powered off and pressing the vol up and down keys while plugging into the PC, it only enters Fastboot mode
I have tried to do it with phone off, rebooting from Crashdump mode, from fastboot and it seems that no combination allows me to do so.
I have also tried just vol up and vol down. App loaded at the flash screen, not loaded, etc.
Thanks in advance
Click to expand...
Click to collapse
It always seems to take me several tries to get it right. I think if I don't hit the vol +/- keys right at the exact time that's the problem. Just be patient and keep trying. The first time I did it, it took me what seemed forever. Thought maybe my phone was broken.
Sent from my IN2025 using Tapatalk
rmiles7721 said:
It always seems to take me several tries to get it right. I think if I don't hit the vol +/- keys right at the exact time that's the problem. Just be patient and keep trying. The first time I did it, it took me what seemed forever. Thought maybe my phone was broken.
Sent from my IN2025 using Tapatalk
Click to expand...
Click to collapse
I have been doing custom roms since the old win ce devices....and yet you sir have been able to make me feel like an idiot haha. Thanks for this. you had it spot on!! thanks so much
Hello Folks. So i have found myself in this situation as well. MY phone wont go off and keeps restarting to CrashDump Mode. As such can't seem to get into EDL mode inorder to flash. Any tips? I have tried all the above methods nothing seems to work. Is there a different key combination or a fastboot command i can use to achieve EDL? Help a brother i'm going nuts. Device IN2020
HaronM said:
Hello Folks. So i have found myself in this situation as well. MY phone wont go off and keeps restarting to CrashDump Mode. As such can't seem to get into EDL mode inorder to flash. Any tips? I have tried all the above methods nothing seems to work. Is there a different key combination or a fastboot command i can use to achieve EDL? Help a brother i'm going nuts. Device IN2020
Click to expand...
Click to collapse
You just need to keep trying it. Make sure you hit vol+/- at the same time and hold for a few seconds, plug in the USB cable, then let off the vol keys. It's difficult to do and get right with two hands. Recently did it again as I wanted to upgrade to the 11 beta from a clean system. Seems like it took me forever to get it this time but eventually I did.
Use usb 2.0 port.
After using 2.0 instead of 3.0 and the phone connected stable for a while (after many tries)
able to finish the msm operation successful ..
But phone not booting .. getting black screen after 1+ logo
at this point I thought to clear cache but My phone is locked I cannot use any recovery .. I cannot even go into oneplu recovery LOL .. It seems like I am doomed
For me personally I could only get it to work on USB2.0 ports. On USB3.0 it just puts me back into fastboot mode or when it does go into EDL MSM tool just fails with a communication error immediately.
I kinda bricked mine as well messing around with GSI ROM's and flashing too hastily and to the wrong partition lol.
It has always worked for me with USB 2.0 port and non oneplus cable.
originable cable would not work for me on usb 3 or USB 2 port, but 3rd party cable start immediately with USB 2 port.
I've had the issue where EDL mode works..... for a few seconds, then the phone reboots.
Very frustrating!
The MSM Download Tool does spot the phone, but since the phone seems to reboot, I don't have enough time to do anything!
Any ideas why this is happening?
OneOfThePetes said:
I've had the issue where EDL mode works..... for a few seconds, then the phone reboots.
Very frustrating!
The MSM Download Tool does spot the phone, but since the phone seems to reboot, I don't have enough time to do anything!
Any ideas why this is happening?
Click to expand...
Click to collapse
You need to already hit start on msmtool BEFORE plugging in phone
1- start MSM tool (prepare the settings and choose the right oos)
2-keep the cable connected to one end (I prefere to keep it connected from the phone side first)
3-keep holding volume up/down for 3-4 sec and connect the other end of the cable to your PC
4-your device will be connected directly stop holding volume up/down and in msm tool press start wait for ≈300 sec
5-now your device should work as it was before
OneOfThePetes said:
I've had the issue where EDL mode works..... for a few seconds, then the phone reboots.
Very frustrating!
The MSM Download Tool does spot the phone, but since the phone seems to reboot, I don't have enough time to do anything!
Any ideas why this is happening?
Click to expand...
Click to collapse
After rebooting my pc, and fiddling with drivers, I got it all sorted finally.
Thanks for your help, folks.
Niranjan Bapat said:
What I did when I was in Crash Dump Mode was,
Press and Hold Power Off and Volume Up button and release when the screen goes off. Now your phone is switched off. Now to enter the EDL mode you need to press and hold volume up and volume down buttons at the same time...and then connect the mobile to pc while still holding the buttons. Done. MSM tool will detect your phone.
NOTE : Also keep the Device Manager window open on the PC while u connect the phone to pc and check if it shows up there.
Click to expand...
Click to collapse
This is a royal pita! I remember when it used to be fun....
Anyway, I've been trying every trick in the book, and then some, but shiznit just isn't going right! The holding of the up and down buttons would be easier if this was the pixel, but it is a tad hard to not mistakenly hit the power button on the other side.
The device manager shows the Qualcomm QDLoader and the msm Downloader is showing the infamous waiting for device... I've been at it for 8 straight hours and if there was a local OnePlus store that sold the international version of the OP8P, that's where I would be heading in a few hours.... It's really frustrating to say the least.
Anyway, when I'm in the bootloader, the device manager shows the Android phone, so I'm thinking that maybe I am in the edl mode when the Qualcomm port shows up, but like I said, the msm is waiting....
tried everything and it is constantly booting into bootloader. I even tried an adjusted fastboot script to boot into EDL but it still boots into bootloader. I have booted into EDL before on a OnePlus 7T, and I have tried multiple times by pressing the OnePlus 8 pro volume buttons at the same time, but always bootloader. Just to check, I tried doing it on my OP 7T again and it worked perfectly fine. Help????
I have had to flash stock 4 times because I land in crash dump mode and it has always been a tricky situation to get into edl.
What worked for me 100% of the time was following the steps in the youtube guide below.
From 2:30 onwards
Hope it helps
I had the same issues, but fixed once read comments as per above. Let me summarize what I did:
1. installed driver Qualcomm HS-USB QDLoader 9008 (I'm using Windows 10) - driver in a cab file should be unpacked using command expand (with proper switches) to preserve folders.
2. launched MSM DT and had it configured and then pressed Verify\Start, as EDL is available only for very short time - 2-3 secs with screen turned off.
3. as my phone was stuck in booting loop I was just keeping presses Vol+/- waiting for EDL to be entered, MDM will find the phone and start uploading data.
Just don't give up trying.
quy said:
Hoping someone can shed some light. Rushing to root phone again to send back warranty replacement, in my haste my laptop died mid flash and now can only boot in Fastboot and Crashdump Mode.
I am attempting to restore to factory via the MSM tool but cannot for the life of me enter EDL mode.
With phone powered off and pressing the vol up and down keys while plugging into the PC, it only enters Fastboot mode
I have tried to do it with phone off, rebooting from Crashdump mode, from fastboot and it seems that no combination allows me to do so.
I have also tried just vol up and vol down. App loaded at the flash screen, not loaded, etc.
Thanks in advance
Click to expand...
Click to collapse
Try different ports. My usb 3 port would force it into fastboot but usb 2 was fine.
What to do if the device doesn't have any usb 2.0 port?

Categories

Resources