Axon 7 brick on DFU mode - ZTE Axon 7 Questions & Answers

My Axon 7 A2017 was bricked and only enter to DFU mode.
Now, i can't do any thing.
Please, help me.
Thanks.

CuDem said:
My Axon 7 A2017 was bricked and only enter to DFU mode.
Now, i can't do any thing.
Please, help me.
Thanks.
Click to expand...
Click to collapse
Did you even search??
Google "4th category brick repair manual". Get a screwdriver ready

Choose an username... said:
Did you even search??
Google "4th category brick repair manual". Get a screwdriver ready
Click to expand...
Click to collapse
I did, but i don't want to open my phone then i want to find another solution, which is easier
i also tried with Deep flash cable but not success.

CuDem said:
I did, but i don't want to open my phone then i want to find another solution, which is easier
i also tried with Deep flash cable but not success.
Click to expand...
Click to collapse
Who wouldn't want to? I was scared sh1tless when I did it. This is the only method that works 100% of times if you do it right.
There's another way, discharging the phone fully and trying to get to FTM mode right after, but I've never heard of anyone pulling it off. Just do the guide. Also deep flash cables are discussed there, don't work.

Related

[Q] Really Bricked?

I had an Asylum Custom Rom installed.
I also had TWRP as the recovery installed.
I decided to try the new COLOR ROM public beta that I got from the OPPO forums.
I went into TWRP recovery, did a full wipe and then proceeded to install the new COLOR ROM.
When I rebooted, the phone never turned on again.
Now I cannot get to fastboot, recovery, or turn on the phone at all.
I browsed through many forums and tried
1. Charging phone for 5 hours (no led light when plugged in) -> nothing
2. Holding Power button for 30 secs, (5 times to try a hard reset) -> nothing
3. Holding Down button for 10 secs -> nothing
4. Power and up volume -> nothing
5. Power and down volume -> nothing
6. Plugged into computer USB and tried all button combos -> nothing
Is my phone really bricked now?
I hope for your sake it really isn't the case. It does seem like you have tried all the usual ways of getting around the symptoms you are describing. It sounds like you had a bad download and flashed it anyway. I hope someone has some advice for you to fix your device. I am currently on Asylum and was just considering trying out the new Color ROM so i think i'll hold off until i know for sure you can resurrect your device.
when you are hooked up to USB on PC can you try ADB? does it even see the device at all?
killerskincanoe said:
I hope for your sake it really isn't the case. It does seem like you have tried all the usual ways of getting around the symptoms you are describing. It sounds like you had a bad download and flashed it anyway. I hope someone has some advice for you to fix your device. I am currently on Asylum and was just considering trying out the new Color ROM so i think i'll hold off until i know for sure you can resurrect your device.
when you are hooked up to USB on PC can you try ADB? does it even see the device at all?
Click to expand...
Click to collapse
Nothing. no response whatsoever. I've worked with many different phones before starting with the Nexus One and I've always been able to get out of a potentially bad situation because I could at least always get to fastboot or recovery, but in this case, nothing. It really is like working with a brick, hence the term "brick". Now i can really understand the meaning of the term.
such a bummer. it certainly makes me think twice about trying other ROMS now jeez
update
Just an update to this thread... I sent my Find 5 to get repaired to try and figure out what the problem was. It turned out that the battery had failed and they replaced the battery for me. Glad to say that my Find 5 is up and running again.
dtwrain said:
Just an update to this thread... I sent my Find 5 to get repaired to try and figure out what the problem was. It turned out that the battery had failed and they replaced the battery for me. Glad to say that my Find 5 is up and running again.
Click to expand...
Click to collapse
good to hear !!
I couldnt really believe that flashing a rom using recovery affects fastboot let alone button combos/charging...
btw what were the costs of replacing the battery ? or was it free of charge under warranty...
dtwrain said:
Just an update to this thread... I sent my Find 5 to get repaired to try and figure out what the problem was. It turned out that the battery had failed and they replaced the battery for me. Glad to say that my Find 5 is up and running again.
Click to expand...
Click to collapse
Glad to hear it turned out that way. Really strange situation.
Oualcomm HS-USB Diagnostics 9008
1) Can you give me some advices? Smartphone OPPO find 5 x909 is in the Oualcomm HS-USB Diagnostics 9008 port. Completely brick. What we gonna do with it ? Where i may download unbrick files and will see unbrick method? Need just rowprogram0.xml, patch0.xml, 8064_msimage.mbn, MPRG8064.hex for OPPO find5 x909 strongly.
2) How i can place other (working) smartphone in Download mode? What i gonna press?
Sorry for my english, and thank you.
olezhek1975 said:
1) Can you give me some advices? Smartphone OPPO find 5 x909 is in the Oualcomm HS-USB Diagnostics 9008 port. Completely brick. What we gonna do with it ? Where i may download unbrick files and will see unbrick method? Need just rowprogram0.xml, patch0.xml, 8064_msimage.mbn, MPRG8064.hex for OPPO find5 x909 strongly.
2) How i can place other (working) smartphone in Download mode? What i gonna press?
Sorry for my english, and thank you.
Click to expand...
Click to collapse
I suggest you to ask addel in oppo forum, she can help you just pm her and tell your problem, because she has an app like odin in samsung to totally flash new rom inage from pc like odin did. But its not officially released by oppo and its hard to find, so i suggest you to contact her
Sent from my GT-I9205 using XDA Free mobile app

LG G2 Bricked, Need urgent assistance.

I need some serious help guys. Phone is stuck at boot logo and wont turn on. IT wont enter recovery mode. it wont hard reset. It wont enter download mode.
The phone was completely stock originally. So i rooted using towelroot and ran the 'AutoREC' program. That did its thing and restarted and got stuck in fastboot mode. couldnt get out of it. Eventually managed to reflash all the original stock ROM partitions and it started to boot again... only to get stuck at the LG logo. I need some serious help.
PC wont detect the phone at all and its as if there is no OS on the phone. I have the D802 variant 32gb.
which kdz variant did you flash.
v.konvict said:
which kdz variant did you flash.
Click to expand...
Click to collapse
D80220C_00
got it from "lg-firmware-rom" after entering my imei
spookyleaf said:
D80220C_00
got it from "lg-firmware-rom" after entering my imei
Click to expand...
Click to collapse
same thing happened to a d802 of a friend of mine. but he flashed the d802h variant. will keep you posted if i find a way out.
I am in the same position. Except I tried to flashify stock recovery on d800 at&t variant. I wanted to install the stock update because I was still stock. Just root with twrp before...I had the sprint variant before the ls980 and it never screwed me over like this. I'll post if I figure anything out... I got to get ahold of shellnutt... He's the g2's god.
Dam. Leme me know what happens
Sent from my Nexus 5 using XDA Free mobile app
spookyleaf said:
Dam. Leme me know what happens
Sent from my Nexus 5 using XDA Free mobile app
Click to expand...
Click to collapse
Have you tried both ways to enter recovery?
Push PWR + Vol Down till you see the LG Logo then release and press both again
Push PWR + Vol Down till you see the LG logo then release and press and hold the volume up and volume down buttons until reset screen appears.
If you can see the LG logo I think you are not Hard Bricked
I haven't tried that exactly. I'll give it a shot when I get a chance
Sent from my Nexus 5 using XDA Free mobile app
You may want to check your internal hardware to be sure it's marked as a D802. Typically the feint white stamp in the lower center/left of the phone with rear cover removed is the true model number. It's also stamped on the board and on the ribbon cables going up eithe side. Your device is showing the signs of a false d802 which has become sadly common in recent months.
If it's legit d802 then flash aboot, boot, laf and power it off.
Then hold voume up and connect to pc while still holding volume up.
Make sure you have the drivers installed, fire up lg mobile support tool or the lg flash tool 2014 (you need your kdz file now - find it using your imei and lg-firmware site)
Okay so I found this: http://forum.xda-developers.com/lg-g2/general/lg-g2-unbrickable-fix-real-hard-brick-t2904404 to get it to come up as a device in Windows and Linux. And this: http://forum.xda-developers.com/showthread.php?t=2582142 I'm sure you read this but you need to do it after following the first guide. I already have a Linux installed and I'm going to try today. I'll update with a guide for you only if you need it and if I succeed. I just need to remind you. You CANNOT mess up on the second guide... Well as far I can tell. But if the first guides label is actually true then maybe I'm wrong.
ok so ive ordered some tools to open up the phone and check the internals. Hopefully its a legit G2. Meanwhile every single possible combination of the power and volume keys does absolutely nothing. If all else fails ill try shorting the capacitors as ive seen on a guide from here and hopefully that will be the end of it. Thanks for all the input guys. Ill keep you posted!
darkpower_4 said:
Okay so I found this: http://forum.xda-developers.com/lg-g2/general/lg-g2-unbrickable-fix-real-hard-brick-t2904404 to get it to come up as a device in Windows and Linux. And this: http://forum.xda-developers.com/showthread.php?t=2582142 I'm sure you read this but you need to do it after following the first guide. I already have a Linux installed and I'm going to try today. I'll update with a guide for you only if you need it and if I succeed. I just need to remind you. You CANNOT mess up on the second guide... Well as far I can tell. But if the first guides label is actually true then maybe I'm wrong.
Click to expand...
Click to collapse
thanks i appreciate that very much. Keep me informed on how it goes. Fingers crossed!
spookyleaf said:
ok so ive ordered some tools to open up the phone and check the internals. Hopefully its a legit G2. Meanwhile every single possible combination of the power and volume keys does absolutely nothing. If all else fails ill try shorting the capacitors as ive seen on a guide from here and hopefully that will be the end of it. Thanks for all the input guys. Ill keep you posted!
Click to expand...
Click to collapse
Plug it into a windows machine, open device manager and look for Qualcomm qhsusb_bulk. If you get that, you're already in bulk and don't need to worry about shorting capacitors. If it's not being recognized in any way, you may be forced into that as a last resort.
spookyleaf said:
ok so ive ordered some tools to open up the phone and check the internals. Hopefully its a legit G2. Meanwhile every single possible combination of the power and volume keys does absolutely nothing. If all else fails ill try shorting the capacitors as ive seen on a guide from here and hopefully that will be the end of it. Thanks for all the input guys. Ill keep you posted!
Click to expand...
Click to collapse
All you really need to open it up is a guitar pick. It pries apart make sure you take the sim card out. After that it's going to take a little swipe around the edge and it'll pop open no problem.
iowabowtech said:
Plug it into a windows machine, open device manager and look for Qualcomm qhsusb_bulk. If you get that, you're already in bulk and don't need to worry about shorting capacitors. If it's not being recognized in any way, you may be forced into that as a last resort.
Click to expand...
Click to collapse
I checked that already. Not going into bulk mode. Seems like the capacitors are my last resort
so ive poped the phone open and guess what... its not a D802.. its a D800.. the at&t version... wtf.. no wonder i bricked it. gonna see if i can use the unbrickable method
did you checked the IMEI?
nope its says on the speaker grille after you remove the back cover. "D800"
how is that possible? did phone information apps showed your device as 802 aswell? did kernel info and phone info in system settings lied too?

Completely dead P9 lite

So it looks like this phone is not completely unbrickable. I've seem to brick mine pretty bad.
The phone doesn't turn on at all. No vibration or other kind of feedback.
Doesn't appear on the computer either.
So my question is: is there any emergency download mode like in qualcomm based phones?
randhackr said:
So it looks like this phone is not completely unbrickable. I've seem to brick mine pretty bad.
The phone doesn't turn on at all. No vibration or other kind of feedback.
Doesn't appear on the computer either.
So my question is: is there any emergency download mode like in qualcomm based phones?
Click to expand...
Click to collapse
I don't know about it.
michal383 said:
I don't know about it.
Click to expand...
Click to collapse
It seems completely dead. Probably only with test point. Warranty most likely will refuse it since it is boot loader unlocked.
randhackr said:
It seems completely dead. Probably only with test point. Warranty most likely will refuse it since it is boot loader unlocked.
Click to expand...
Click to collapse
Yes Warranty falls if the bootloader unlocked. Test Point could help.
Well warranty will most likely only complain if it was bricked by the user and software modification.
If your phone broke because of an hardware issue, you have a chance that warranty still repairs it for free.
Schlengge said:
Well warranty will most likely only complain if it was bricked by the user and software modification.
If your phone broke because of an hardware issue, you have a chance that warranty still repairs it for free.
Click to expand...
Click to collapse
Well since it broke after I flashed b160 firmware I am most likely SOL. Since I had twrp flashed they will find out that it was modified..
My advice is not to mess with fastboot mode. Flash twrp and be careful with what you flash.
Did you tried to flash original firmware with the three buttons?
Sent from my HUAWEI VNS-L31 using XDA-Developers mobile app
Potato997 said:
Did you tried to flash original firmware with the three buttons?
Sent from my HUAWEI VNS-L31 using XDA-Developers mobile app
Click to expand...
Click to collapse
Yup. It's completely dead. No fastboot mode, no recovery or erecovery. It simply does not turn on (or enumerate in a computer either).
If you could boot into recovery,the rest would be simple....download the stock firmware, unzip it and push the file to your phone,then install
LiaquateRahiman said:
If you could boot into recovery,the rest would be simple....download the stock firmware, unzip it and push the file to your phone,then install
Click to expand...
Click to collapse
He can't enter in recovery or fastboot.
Potato997 said:
He can't enter in recovery or fastboot.
Click to expand...
Click to collapse
Have you tried to enter fastboot or recovery solely using the button combos? or did you try using adb as well? It's possible your battery deep-discharged, or your power adapter/connectors are faulty.
Potato997 said:
He can't enter in recovery or fastboot.
Click to expand...
Click to collapse
Yes I cant enter anything in fact. There was a suggestion to connect the phone without battery to the computer but it implies opening up the phone and even if it did something I don't have the tools to flash it. (dc-phoenix only seems to work with phones with fastboot working)
As far as I know the symptoms that my phone is experiencing are due to the fastboot partition being messed up.
As far I was able to research there is another boot loader before the fastboot one. But the phone doesn't respond at all, it is dead. I will ask around in phone repair shops if they can reflash the phone.
randhackr said:
Yes I cant enter anything in fact. There was a suggestion to connect the phone without battery to the computer but it implies opening up the phone and even if it did something I don't have the tools to flash it. (dc-phoenix only seems to work with phones with fastboot working)
As far as I know the symptoms that my phone is experiencing are due to the fastboot partition being messed up.
As far I was able to research there is another boot loader before the fastboot one. But the phone doesn't respond at all, it is dead. I will ask around in phone repair shops if they can reflash the phone.
Click to expand...
Click to collapse
Before you do anything rash, have you considered getting a usb jig? Simply put the stock firmware on the jig then plug it into the usb port on your phone. It will automatically put your phone into download mode and install the firmware. Here's the link to make your own usb jig http://forum.xda-developers.com/galaxy-s2/help/guide-how-to-make-usb-jig-reset-binary-t1604707. Hopefully this helps!!!
LiaquateRahiman said:
Before you do anything rash, have you considered getting a usb jig? Simply put the stock firmware on the jig then plug it into the usb port on your phone. It will automatically put your phone into download mode and install the firmware. Here's the link to make your own usb jig http://forum.xda-developers.com/galaxy-s2/help/guide-how-to-make-usb-jig-reset-binary-t1604707. Hopefully this helps!!!
Click to expand...
Click to collapse
That is for samsung phones. I gave on trying to fix the phone. Next week I'm going to send it to a phone repair shop and see what they can do.
Edit: The phone repair guy says that the only way it can be repaired is by replacing the emmc or replacing the motherboard. So for now the phone will sit in the drawer until I manage to get a new board.
Hello
I had the same problem with my honor 7, the only solution is to replace the motherboard :/
If the phone is completely dead, warranty will accept it just because they will change your motherboard if they can't turn it on. I had the same problem last week, probably an hardware fail, I gave it to them saying that the phone simply turned off and they changed the whole motherboard (bootloader unlocked, twrp and root).
Well I tried sending it to the repair center. Two days later they replaced the whole phone, they said that there was an issue with the power ic.
B160 works for me.. hmm.... using it for like a [email protected]@
might be your hardware that cause the problem and not the firmware?
ivanwong1989 said:
B160 works for me.. hmm.... using it for like a [email protected]@
might be your hardware that cause the problem and not the firmware?
Click to expand...
Click to collapse
I'm starting to think so, I've flashed the replacement and it didn't brick. May or may not be related to the headers, but I don't want to be creative right now since I need the phone lol.
What is b160 can you explain

Qualcomm hs-usb qdloader 9008 nexus 6P (HELP!)

Hi there, I've been browsing through the threads related to unbricking of the Nexus 6P stuck in qualcomm hs-usb qdloader 9008 mode, really desperate to get my device working again if even possible however I've tried for about four days now different ways and files and I've had no luck.
My bootloader is locked and no ADB etc managed to get my device showing as the 9008 port so I think it's stuck in EDL.
Following guides, this is the furthest I've yet to get (In screenshot)
Could anyone shed some light and some assistance please? what am I doing wrong!?
attempted to apply for heat some to the device then re flash ?
blackcell1 said:
attempted to apply for heat to the device then re flash ?
Click to expand...
Click to collapse
Sorry, I don't quite understand what you mean?
Clarkeofcurtis said:
Sorry, I don't quite understand what you mean?
Click to expand...
Click to collapse
Use a hairdryer to warm up the back of the phone.
Are you pulling my leg? Warm it up then reflash?
nah im not trying to make you destroy your phone, being rather serious with this method. i use it on a daily basis to solve phones that fail during restoring factory images. i wouldn't know how long to give it with a hair dryer as i have access to a heat gun/heat mats .
just think of it as a cheap mans re balling method
blackcell1 said:
nah im not trying to make you destroy your phone, being rather serious with this method. i use it on a daily basis to solve phones that fail during restoring factory images. i wouldn't know how long to give it with a hair dryer as i have access to a heat gun/heat mats .
just think of it as a cheap mans re balling method
Click to expand...
Click to collapse
Sorry haha, I'm a noob with most of this android stuff bar rooting and flashing a few devices prior! I shall give it a go now and get back to you - thank you for the advice
Clarkeofcurtis said:
Sorry haha, I'm a noob with most of this android stuff bar rooting and flashing a few devices prior! I shall give it a go now and get back to you - thank you for the advice
Click to expand...
Click to collapse
good luck, id give it a good couple of minutes on the highest setting, just so its a little hot to the touch. and attempt the flashing of the files when its still hot/warm.
blackcell1 said:
good luck, id give it a good couple of minutes on the highest setting, just so its a little hot to the touch. and attempt the flashing of the files when its still hot/warm.
Click to expand...
Click to collapse
thank you so much that worked, it has said flash successful, first time I got a google logo but now nothing, what would be my next step please?
if the bootloader is unlocked then you can directly flash the firmware. but if its not google "nexus ota" and then on your phone jump into the recovery and check the firmware model number and download the same ota and adb sideload it.
im not 100% sure on the next step as I've never had a nexus 6p with a dead bootloader. but thats what id do.
---------- Post added at 04:50 PM ---------- Previous post was at 04:49 PM ----------
but from my personal experience with having to heat a phone up to restore factory images, it kinda means the phone is nearing the end of its life and id start thinking about buying your next phone before it sh*ts the bed.
blackcell1 said:
if the bootloader is unlocked then you can directly flash the firmware. but if its not google "nexus ota" and then on your phone jump into the recovery and check the firmware model number and download the same ota and adb sideload it.
im not 100% sure on the next step as I've never had a nexus 6p with a dead bootloader. but thats what id do.
Click to expand...
Click to collapse
Thank you for the reply and continuing to help, after seeing the google logo just once I'm getting nothing again - I'm even more determined now though as It's been dead for 2 months so this is the furthest I've gotten - the application of heat is what did it for me and fixed the error I was getting, can't get into recovery now though holding power + down etc
Clarkeofcurtis said:
Thank you for the reply and continuing to help, after seeing the google logo just once I'm getting nothing again - I'm even more determined now though as It's been dead for 2 months so this is the furthest I've gotten - the application of heat is what did it for me and fixed the error I was getting, can't get into recovery now though holding power + down etc
Click to expand...
Click to collapse
yeah can you access the bootloader at all ? does it say that the bootloader is locked ? from trying to restore LG's it sometimes has to be re heated a few times, but yeah if you need to re heat it to get further into the phone then its pretty much a lost cause. the only reason i do it is to remove the data so we can resell the device.
blackcell1 said:
yeah can you access the bootloader at all ? does it say that the bootloader is locked ? from trying to restore LG's it sometimes has to be re heated a few times, but yeah if you need to re heat it to get further into the phone then its pretty much a lost cause. the only reason i do it is to remove the data so we can resell the device.
Click to expand...
Click to collapse
I can get into the andriod screen where you can select recovery and such, with the BL, Baseband product variation and such, where should I go from here?
Oh right, so even once restored to firmware, will it be useless do you think if I can even manage to?
Clarkeofcurtis said:
I can get into the andriod screen where you can select recovery and such, with the BL, Baseband product variation and such, where should I go from here?
Oh right, so even once restored to firmware, will it be useless do you think if I can even manage to?
Click to expand...
Click to collapse
Sorry if you can't access the recovery from the bootloader and its in locked state then your a member of the lovely group of BLOD (bootloader of death) if you hit recovery does it show a little android logo and sit there?
Sorry for the late reply
blackcell1 said:
Sorry if you can't access the recovery from the bootloader and its in locked state then your a member of the lovely group of BLOD (bootloader of death) if you hit recovery does it show a little android logo and sit there?
Sorry for the late reply
Click to expand...
Click to collapse
I believe so, I can just about get into the bootloader at the best of times and when I do I can select options but once proceeding to start said mode phone freezes so can't get into recovery mode :/
Thank you for your continuous help, only way i can get it into bootloader is by heating it up so does that mean for the device to ever work It'll need heat every time? looking like a spares and repairs listing on ebay
Clarkeofcurtis said:
I believe so, I can just about get into the bootloader at the best of times and when I do I can select options but once proceeding to start said mode phone freezes so can't get into recovery mode :/
Thank you for your continuous help, only way i can get it into bootloader is by heating it up so does that mean for the device to ever work It'll need heat every time? looking like a spares and repairs listing on ebay
Click to expand...
Click to collapse
Hello....
How did you manage to get in to EDL mode..? I'm really curious. With stock bootloader? Since you can't access recovery
Also what is exactly displayed in Windows device manager?
You are using an outdated QFil version... It is from 2014 àr 2015.
Do a google search with: QPST_2.7.453.0 . This version seem to be from 2016.
Use the first link from the result. I analysed the files with virustotal, those seem clean or malware...
Also when plugging your usb cord to your PC, does your phone vibrate? Or does the LED blink in red?
You may have to press power button when plugging the usb cord or press power button for a certain amount of time before you plug the usb cord. I'm not completly sure, but your phone may not be in the "proper" EDL state to accept the QFil flash.
Good luck... :good:
Is it possible to send me the guide you used? Thanks.
Clarkeofcurtis said:
Hi there, I've been browsing through the threads related to unbricking of the Nexus 6P stuck in qualcomm hs-usb qdloader 9008 mode, really desperate to get my device working again if even possible however I've tried for about four days now different ways and files and I've had no luck.
My bootloader is locked and no ADB etc managed to get my device showing as the 9008 port so I think it's stuck in EDL.
Following guides, this is the furthest I've yet to get (In screenshot)
Could anyone shed some light and some assistance please? what am I doing wrong!?
Click to expand...
Click to collapse
Hey there sorry for slow replies, will be back on my desktop in an hour I'll send you links for what I followed and such, I think the only reason my device was in EDL mode was due to a hardware fault? As my device is faulty indefinitely as I had to use a hairdryer to warm it up while flashing this then allowed it to enter firehose state which a lot of people seem to error with - after all my attempts and research I'm to velieve there's a fault with the phone itself the only way I could get it to even power up was applying heat to it after removing the back panel
As blackcell said deballing or something? Worked a treat!
Furthest I've managed to get now is into my boot loader however everything is locked - when I press enter recovery my handset just freezes ?
5.1 said:
Hello....
How did you manage to get in to EDL mode..? I'm really curious. With stock bootloader? Since you can't access recovery
Also what is exactly displayed in Windows device manager?
You are using an outdated QFil version... It is from 2014 àr 2015.
Do a google search with: QPST_2.7.453.0 . This version seem to be from 2016.
Use the first link from the result. I analysed the files with virustotal, those seem clean or malware...
Also when plugging your usb cord to your PC, does your phone vibrate? Or does the LED blink in red?
You may have to press power button when plugging the usb cord or press power button for a certain amount of time before you plug the usb cord. I'm not completly sure, but your phone may not be in the "proper" EDL state to accept the QFil flash.
Good luck... :good:
Click to expand...
Click to collapse
Thanks pal if you check last post I wrote about my EDL mode forgot to tag you my apologies, as for my LED I've never seen that light up since I bricked it, even when google logo came up etc and while in the boot loader
Clarkeofcurtis said:
Thanks pal if you check last post I wrote about my EDL mode forgot to tag you my apologies, as for my LED I've never seen that light up since I bricked it, even when google logo came up etc and while in the boot loader
Click to expand...
Click to collapse
Light usually a red LED blink while in proper EDL state as far as I know. Could be something else on the N6P. Well, it looks like you are SOL. Sorry, I don't know what else to say, since you exhausted all possibilities...
Good luck...

I have totally bricked my zte axon 7 a2017g and i seriously need help!!

So guys, i have tried to downgrade my phone from android 7.1.1 to 6.0 which ended in a softbrick, after that i tried 2 flash a stock rom but that completely bricked it and now my phone wont dont anything anymore except for some kind of mode that my computer can detect in device it sees the qualcomm port 9008 device but there a thing it just wont work miflash doesnt recognize it and i cant find any sollutions online please help
tnhx
Daan_K said:
So guys, i have tried to downgrade my phone from android 7.1.1 to 6.0 which ended in a softbrick, after that i tried 2 flash a stock rom but that completely bricked it and now my phone wont dont anything anymore except for some kind of mode that my computer can detect in device it sees the qualcomm port 9008 device but there a thing it just wont work miflash doesnt recognize it and i cant find any sollutions online please help
tnhx
Click to expand...
Click to collapse
I wonder:
-Which is your phone model, as stated on the back of the phone?
-Which is the file that you used to downgrade?
-Which stock rom did you try to flash?
The fix is pretty simple but seeing how you borked three simple procedures I'd like to know everything and lay it out for you precisely. You have to have done something horribly wrong to softbrick a phone with the stock updater system...
Choose an username... said:
I wonder:
-Which is your phone model, as stated on the back of the phone?
-Which is the file that you used to downgrade?
-Which stock rom did you try to flash?
The fix is pretty simple but seeing how you borked three simple procedures I'd like to know everything and lay it out for you precisely. You have to have done something horribly wrong to softbrick a phone with the stock updater system...
Click to expand...
Click to collapse
Okay at first my phone model on the back of my device is, as i mentioned before, "zte a2017g" thats the european version of this phone, chinese is "a2017" and the us version is "2017u".
The file i used 2 downgrade was the stock rom from the official website of zte
it was the full edl file buildnumber b10.
and again i once sofbricked it, i know how 2 fix that, but now it hard bricked, well i think so at least, i cant get it to boot into bootloader, recovery or anything, when i hold the power button it shakes the device, and it shows the zte logo for about 2 seconds then it disappears, and nothing happens but my computer does recognize it as a connected device but i cant use miflash of something else because those programs dont see it.
Daan_K said:
Okay at first my phone model on the back of my device is, as i mentioned before, "zte a2017g" thats the european version of this phone, chinese is "a2017" and the us version is "2017u".
The file i used 2 downgrade was the stock rom from the official website of zte
it was the full edl file buildnumber b10.
and again i once sofbricked it, i know how 2 fix that, but now it hard bricked, well i think so at least, i cant get it to boot into bootloader, recovery or anything, when i hold the power button it shakes the device, and it shows the zte logo for about 2 seconds then it disappears, and nothing happens but my computer does recognize it as a connected device but i cant use miflash of something else because those programs dont see it.
Click to expand...
Click to collapse
all right. it's still freaking weird. Use my DFU unbrick guide but only do step 4 and 5 (but use the files on the top anyways)(you just have to hold Vol+ and Vol - and insert the cable instead of taking the phone apart and shorting pins). After that check the driver, if it is still Qualcomm HS-USB QDLoader 9008 then flash with MiFlash, if not, tell me what appears
Choose an username... said:
all right. it's still freaking weird. Use my DFU unbrick guide but only do step 4 and 5 (but use the files on the top anyways)(you just have to hold Vol+ and Vol - and insert the cable instead of taking the phone apart and shorting pins). After that check the driver, if it is still Qualcomm HS-USB QDLoader 9008 then flash with MiFlash, if not, tell me what appears
Click to expand...
Click to collapse
allright allready thanks loads for your support but could you maybe send the right file to flash because i have no idea, and please, the files for a2017g not a2017 or a2017u thankyou so much
Daan_K said:
allright allready thanks loads for your support but could you maybe send the right file to flash because i have no idea, and please, the files for a2017g not a2017 or a2017u thankyou so much
Click to expand...
Click to collapse
they are in the guide. at the top, there's a link to WesTD's EDL flashable files. Get one for A2017G, for example B09
Choose an username... said:
they are in the guide. at the top, there's a link to WesTD's EDL flashable files. Get one for A2017G, for example B09
Click to expand...
Click to collapse
Allright, thankyou so much my dude
Choose an username... said:
all right. it's still freaking weird. Use my DFU unbrick guide but only do step 4 and 5 (but use the files on the top anyways)(you just have to hold Vol+ and Vol - and insert the cable instead of taking the phone apart and shorting pins). After that check the driver, if it is still Qualcomm HS-USB QDLoader 9008 then flash with MiFlash, if not, tell me what appears
Click to expand...
Click to collapse
aight, as i thought this didnt work, i tired it but miflash basicly just gave me an error notification.
also when i go into device manager i can see that my device is connected but i show the name with a yellow triangle with a ! in it i have no clue what this means can u please help me with this. i rlly want my phone back
Daan_K said:
aight, as i thought this didnt work, i tired it but miflash basicly just gave me an error notification.
also when i go into device manager i can see that my device is connected but i show the name with a yellow triangle with a ! in it i have no clue what this means can u please help me with this. i rlly want my phone back
Click to expand...
Click to collapse
First of all, if you get an error TELL ME what it says!
Send me a screenshot of the device manager, i can do very little with "yellow triangle"
Don't bother? That guy is using XDA as a free emergency support without looking for one second.
He probably would like you to do a teamviewer while he's watching football with a beer and not even say thank you.
I'm horrified.
RedWave31 said:
Don't bother? That guy is using XDA as a free emergency support without looking for one second.
He probably would like you to do a teamviewer while he's watching football with a beer and not even say thank you.
I'm horrified.
Click to expand...
Click to collapse
rlly m8. im just a guy who needs help with his phone the guy "choose a username..." i helping me with it, ive been unable 2 fix my phone with any of the other threads i just need some help and i have said thanks alot, dont call me that
Daan_K said:
rlly m8. im just a guy who needs help with his phone the guy "choose a username..." i helping me with it, ive been unable 2 fix my phone with any of the other threads i just need some help and i have said thanks alot, dont call me that
Click to expand...
Click to collapse
Sorry, I don't believe you for one second. Like litterally THOUSANDS of people here and here opening "bricked plz hlp" threads, you didn't even have the BASIC, LOWEST courtesy of writing more than 10 words of gibberish whining about your situation, without a single usefull element of context.
Proof of that in the NUMEROUS questions asked about ELEMENTARY elements about your situation. You're litterally the kind of person that would go to a car mechanic, drop the keys on the counter saying "my car is broken, fix it" and just leave without a single word added. That's RUDE and, yeah, I'm tired AF of people like you who can't READ THE DAMN XDA RULES and got NOT education whatsoever.
Nd writng frm a phone in T9 mde dsnt rlly bring nythng mre on the tble either.
Too bad you found somebody to help, as it's only encouraging that kind of behaviour.
//Rant off//
@Daan_K this EDL Tool can help https://forum.xda-developers.com/axon-7/development/axon-7-edl-tool-flash-backup-restore-t3750759
Choose an username... said:
First of all, if you get an error TELL ME what it says!
Send me a screenshot of the device manager, i can do very little with "yellow triangle"
Click to expand...
Click to collapse
this is a screenshot of my device manager, and what I meant with yellow triangle, also it doesn't work with the edl-tool nor the axon7tool
Daan_K said:
this is a screenshot of my device manager, and what I meant with yellow triangle, also it doesn't work with the edl-tool nor the axon7tool
Click to expand...
Click to collapse
Okay, let's try two things:
First right click on it and uninstall the device, also delete driver software for the device (it will be a checkbix asking for that after you hit 'uninstall device'). After that, hold Volume up, Volume down, and Power until the Device manager refreshes. After that the driver should reinstall itself. If it still shows with the yellow triangle, right click it, click on Properties, and send me a screenshot (or translate me what it says on the status part)
https://forum.xda-developers.com/axon-7/how-to/a2017-4th-category-brick-repair-manual-t3585898
if you can only get to dfu mode and nothing else, use thise guide, you'll have to dismantle your phone. Had to unbrick mine with this from a hardbrick, worked flawlessly
IvI97 said:
https://forum.xda-developers.com/axon-7/how-to/a2017-4th-category-brick-repair-manual-t3585898
if you can only get to dfu mode and nothing else, use thise guide, you'll have to dismantle your phone. Had to unbrick mine with this from a hardbrick, worked flawlessly
Click to expand...
Click to collapse
Hey, a couple of things: one, i've updated the guide, it's around, much simpler to use. just saying. Two, this guy has the right driver. Don't confuse him with DFU while at least for now it is not.
Choose an username... said:
Okay, let's try two things:
First right click on it and uninstall the device, also delete driver software for the device (it will be a checkbix asking for that after you hit 'uninstall device'). After that, hold Volume up, Volume down, and Power until the Device manager refreshes. After that the driver should reinstall itself. If it still shows with the yellow triangle, right click it, click on Properties, and send me a screenshot (or translate me what it says on the status part)
Click to expand...
Click to collapse
omg the triangle is gone, thankyousomuch, but what can I use now 2 fix it further?? is that in your guide maybe?
choose an username... said:
hey, a couple of things: One, i've updated the guide, it's around, much simpler to use. Just saying. Two, this guy has the right driver. Don't confuse him with dfu while at least for now it is not.
Click to expand...
Click to collapse
omygod it ****ing working, choose an username man, i can't thank you enough, seriously ur the best man lots of love for doing this

Categories

Resources