Hi Everyone I'm not even sure if anyone is going to reply to this but heres the deal. yesterday i flashed a custom rom to my phone s4 (sgh-i337m unlocked carrier) i have twrp3 installed for custom restore and i did make a restore file when my phone was still on lollipop, and i think that the backup worked because the boot screen is back to stock but now heres my issue, i power up my phone i get past the "galaxy s4" screen but get stuck on the samsung animation, i gave up on it after it sitting there for 2 hours then i removed the battery and then flash installed 7.x nougut onto it, but cant get playstore but thats just minor but what i do want is to go back to full stock no root, i feel that ive made a mistake and im just not comfortable with it anymore even if i loose all my stuff thats fine ive had the phone for a week, i do have odin on my computer but dont know how to use it because theres icons like bl, ap, cp and csc i dont know what those are well i know ap for installing twrp. I'm needing help like yesterday
You will have to download the stock ROM and flash it with Odin. Stock ROMs can be downloaded from sammobile.com, but download speeds are slow for non-premium users.
Flash guides can be found with everywhere.
Confirm that the model # is sgh-i337m in download mode. If it is, do this:
download Odin 3.07: https://www.google.ca/url?sa=t&rct=...168421&usg=AFQjCNHMbaSWjgVwWQGtMVr1TvJSsXWUcA
download the latest 5.01 firmware from here: https://www.sammobile.com/firmwares/galaxy-s4/SGH-I337M/BMC/download/I337MVLSGQB1/125370/ (This is for Bell but it doesn't matter because Rogers, Bell, Telus, Koodo, and Fido use the same ROM with some minor carrier customization). Unzip the file once to create a tar.md5 file;
put the phone into download mode;
open Odin and click on PDA, select the tar.md5 file;
connect the phone to the computer using the original Samsung USB cable;
uncheck everything except f reset time and flash the phone;
when you see the word RESET in the status window, remove the USB cable from the phone, remove the battery, replace the battery; boot the phone into recovery mode, factory reset, and reboot.
How to get into download mode: https://www.youtube.com/watch?v=7nC2vX492wI
How to get into recovery mode: https://www.youtube.com/watch?v=LkrUVSxGW9g
The correct forum for the sgh-i337m is here: https://forum.xda-developers.com/galaxy-s4-att
audit13 said:
Confirm that the model # is sgh-i337m in download mode. If it is, do this:
download Odin 3.07: https://www.google.ca/url?sa=t&rct=...168421&usg=AFQjCNHMbaSWjgVwWQGtMVr1TvJSsXWUcA
download the latest 5.01 firmware from here: https://www.sammobile.com/firmwares/galaxy-s4/SGH-I337M/BMC/download/I337MVLSGQB1/125370/ (This is for Bell but it doesn't matter because Rogers, Bell, Telus, Koodo, and Fido use the same ROM with some minor carrier customization). Unzip the file once to create a tar.md5 file;
put the phone into download mode;
open Odin and click on PDA, select the tar.md5 file;
connect the phone to the computer using the original Samsung USB cable;
uncheck everything except f reset time and flash the phone;
when you see the word RESET in the status window, remove the USB cable from the phone, remove the battery, replace the battery; boot the phone into recovery mode, factory reset, and reboot.
How to get into download mode: https://www.youtube.com/watch?v=7nC2vX492wI
How to get into recovery mode: https://www.youtube.com/watch?v=LkrUVSxGW9g
The correct forum for the sgh-i337m is here: https://forum.xda-developers.com/galaxy-s4-att
Click to expand...
Click to collapse
Thankyou i did fully verify everything before hand and yes it is sgh-i337m i actually got a different rom fully working and i do thank all users that did view and help me out. I did find a way to get gapps installed wothout issues. I still cant restore the device back to stock but i actually bought a replacement stock phone and use this one that were communicating on now. So now i have two phones completely identical minus the fact that one is unlocked from at&t and the other was never locked to anything.
Pwnycorn said:
You will have to download the stock ROM and flash it with Odin. Stock ROMs can be downloaded from sammobile.com, but download speeds are slow for non-premium users.
Flash guides can be found with everywhere.
Click to expand...
Click to collapse
Took a while but finally acquired 2 stock roms one telus and one sasktel. I will probably do a rom swap one day
The non-aws version of the s4 sold in Canada is the sgh-i337m. You can cross flash roms from any carrier as they are all the same except for a bit of customisation by adding their own apps.
A quick download source is updato.com.
Btw, the Canadian s4 forum is here: https://forum.xda-developers.com/galaxy-s4-att
I'm stuck also on the samsung animation screen, and flashing a stock rom does nothing for me it's stuck. I can't even go into stock recovery. everytime i do try it just say recovery booting and loops back into samsung screen. is there any way to fix this?
Thanks I'm new to the site and didn't know there was a Canadian s4 forum, I thought it was a specific device forum because my phone isn't att because att is not active on my area, we have telus, koodo, rogers, sasktel and bell
SPheDaGhost said:
I'm stuck also on the samsung animation screen, and flashing a stock rom does nothing for me it's stuck. I can't even go into stock recovery. everytime i do try it just say recovery booting and loops back into samsung screen. is there any way to fix this?
Click to expand...
Click to collapse
One thing I did because I was in the same boat and it sounds like your stuck in a soft boot is download lots of roms to a SD card and trial and error, use the latest version of twrp and flash the first version of twrp to the phone with Odin there's lots of YouTube videos to assist you, also when using a custom rom (in my experience) is that you also have to download gapps to gain the full google/android experience and it's safer to download apps with Google playstore compared to using a browser. Also when flashing remember to wipe catche and delvic before rebooting. Hope this helps and if your using the same kinda device as me I'd recommend the 7.1.2 rom by JDC it works pretty good and it feels like the s8
Related
i used the exe og legija to recover my i9505 so i can boot in download mode but
when i install an official firmware with pit thru odin after the flash is pass success the i9505 is dead again ...
any idea?? In the phone when start flashing is appear 3 lines in red saying:
START [240,1440]
BAR [240,1440]
END [240,1440]
any help plz thx
You are in the wrong forum. This one is for the S4 Active and its European counterpart. Sounds like you have a regular S4 as we cannot yet flash ROMs on our S4 Active phones.
No , you're in the wrong forum dude
Sent from my GT-I9505 using XDA Premium HD app
Miami_Son said:
You are in the wrong forum. This one is for the S4 Active and its European counterpart. Sounds like you have a regular S4 as we cannot yet flash ROMs on our S4 Active phones.
Click to expand...
Click to collapse
I'm pretty sure this is the regular S4 section
Sent from my Googley Sammy Jellybean
tatperson said:
I'm pretty sure this is the regular S4 section
Sent from my Googley Sammy Jellybean
Click to expand...
Click to collapse
It is, now that a mod moved the thread.
yes is an european s4 i9505
yes i am from spain this s4 i9505 is european version, from vodafone, in odin when i start download mode it says wrie protection enable and when flashing it sen the messages i say above. i use the pit and the stock fw, in odin it says it pass and all succesfull but when i try to power the phone it dont boot, and goes in qualcom mode. also when i enter in download mode at star says phone coud not do normal bot in red, like that:
could not do normal boot
odin mode
product name : i9505
Current binary sumsung oficial
System status: Custom
CSB-OEM_CONFIG _FILES_SYS: 0x30
write protection : enable
We need to know exactly what you've done to the phone in the order you've done it - firmware which was originally on the phone, any OTA updates, exactly what you flashed/in what order, what happened to the phone that made you need to Odin flash it.
Little details will be important so far as getting your phone up & running as soon as possible goes, I.E the less details you give the longer it's going to take for that to happen
MistahBungle said:
We need to know exactly what you've done to the phone in the order you've done it - firmware which was originally on the phone, any OTA updates, exactly what you flashed/in what order, what happened to the phone that made you need to Odin flash it.
Little details will be important so far as getting your phone up & running as soon as possible goes, I.E the less details you give the longer it's going to take for that to happen
Click to expand...
Click to collapse
hi, is a friend phone, he flashes with odin to install 4.3 custom(i don't know what custom he use) it fails and he brick the phone, can't no enter in recovery and can't enter in download mode, also the phone no power on, when he let me the phone for repair. Know i can enter in download mode.
First of all i try to flash a new rom custom but it says no pit partition. Then i download from sammobile a stock rom of vodafone and the pit file for the S4 i9505, i flash it with pit and the stock official rom of the terminal (re-partition mark,f.reset time mark, and autoreebot mark). Odin end and say pass. but when i try to power on the phone go again into a brick (phone, can't no enter in recovery and can't enter in download mode, also the phone no power on). i use odin 3.07 , 3.09 and 1.85 i got this versions and i try some configurations like unmark re-partition,and unmark autoreboot with the same problem. (He turn un qualcome mode). i also try to install a new recovery and the same syntoms. also when i flash any thing the phone goes to the same status all ok but no power on, no recovery and no download mode.
any ideas???
Can I get a little help here? I have a rooted, otherwise stock i337 that I just used the TWRP root app. I wanted to make a backup of my phone before I flashed a new rom. It downloaded jflteatt and I verified and installed it to /dev/block/mmcblk0p21. then i tried to make a backup, and i'm stuck at "Downloading.... do not turn off target!!!" In the upper left corner there's a "Could not do normal boot. ODIN Mode.
I found the post "[GUIDE] How to Unbrick your AT&T S4 I337 OTA UCUAMF3" but am hesitant to use it, as I am not sure that is what I need to do. I also found some other similar posts, but for different devices so I am again hesitant to rely on those.
I tried pressing home, power and volume down, but it just resets back to this screen. Also, I originally posted this request on the TWRP page, but I think it should be here. If so, I will delete it there.
Please help?
@kamikazees
If you could give more detail that would also help other to help u....such as what firmware that u are running before bricked...... well seem to me that u are either MF3 or MK2 firmware and u installed TWRP ...... u can only install safestrap recovery if u are on MF3 or MK2 firmware. ....Follow my thread http://forum.xda-developers.com/showthread.php?t=2621279 it should get u back to MK2 firmware. .....goodluck
Swyped From MK2 Dark Venom SS Edition
Thank you for the quick response. I have a small update since my first post. I found a poster in another section who got his phone rebooted by trying to send it to download mode, then cancelling out. I did that (pressing power, home and vol down), then when the phone "buzzed" I let off those keys and pressed them again. The phone rebooted, apparently normally.
So now I can check my firmware. Checking firmware is on the "baseband version" right? If so, then that info on my phone is I337UCUEMK2," which I guess is the MK2 firmware.
I deleted the TWRP app, but I'm not sure now if I've even got a recovery (if TWRP failed to install, maybe I'm still on stock?). Do I need to go ahead do the full ODIN tar file unbrick from where I am now? The phone appears to be operating normally.
If not, should I just go ahead and install safestrap recovery? I am trying to eventually get rid of all the bloated samsung junk and get to CM or another ROM. The S4 seems a bit more touchy than some of my previous phones.
kamikazees said:
Thank you for the quick response. I have a small update since my first post. I found a poster in another section who got his phone rebooted by trying to send it to download mode, then cancelling out. I did that (pressing power, home and vol down), then when the phone "buzzed" I let off those keys and pressed them again. The phone rebooted, apparently normally.
So now I can check my firmware. Checking firmware is on the "baseband version" right? If so, then that info on my phone is I337UCUEMK2," which I guess is the MK2 firmware.
I deleted the TWRP app, but I'm not sure now if I've even got a recovery (if TWRP failed to install, maybe I'm still on stock?). Do I need to go ahead do the full ODIN tar file unbrick from where I am now? The phone appears to be operating normally.
If not, should I just go ahead and install safestrap recovery? I am trying to eventually get rid of all the bloated samsung junk and get to CM or another ROM. The S4 seems a bit more touchy than some of my previous phones.
Click to expand...
Click to collapse
Your stock recovery is probably broken, and so it would be best to at least reflash the stock recovery. However, you should be just fine if you want to only install Safestrap and leave recovery broken. I just wouldn't recommend that.
DeadlySin9 said:
Your stock recovery is probably broken, and so it would be best to at least reflash the stock recovery. However, you should be just fine if you want to only install Safestrap and leave recovery broken. I just wouldn't recommend that.
Click to expand...
Click to collapse
Ok, I want to fix the recovery. Can I use ODIN for that? One post I found said I cannot: http://forum.xda-developers.com/showthread.php?t=2576291. It was several months ago, however, so I am not sure if it still holds true.
If I can use ODIN, I see that the stock recovery file is in ted77usa's post #3: http://forum.xda-developers.com/showthread.php?t=2621279. After putting my phone in download mode and connecting it to ODIN, in which slot would I put that file? Some older posts say to put it in the PDA slot, which appears to be the AP slot.
Thanks for your patience. I really don't want to mess this up again.
kamikazees said:
Ok, I want to fix the recovery. Can I use ODIN for that? One post I found said I cannot: http://forum.xda-developers.com/showthread.php?t=2576291. It was several months ago, however, so I am not sure if it still holds true.
If I can use ODIN, I see that the stock recovery file is in ted77usa's post #3: http://forum.xda-developers.com/showthread.php?t=2621279. After putting my phone in download mode and connecting it to ODIN, in which slot would I put that file? Some older posts say to put it in the PDA slot, which appears to be the AP slot.
Thanks for your patience. I really don't want to mess this up again.
Click to expand...
Click to collapse
The first one is in img format and won't work through ODIN, but you can use those commands from terminal emulator to flash it if you download it. Otherwise, the TAR files do work just fine.
kamikazees said:
Ok, I want to fix the recovery. Can I use ODIN for that? One post I found said I cannot: http://forum.xda-developers.com/showthread.php?t=2576291. It was several months ago, however, so I am not sure if it still holds true.
If I can use ODIN, I see that the stock recovery file is in ted77usa's post #3: http://forum.xda-developers.com/showthread.php?t=2621279. After putting my phone in download mode and connecting it to ODIN, in which slot would I put that file? Some older posts say to put it in the PDA slot, which appears to be the AP slot.
Thanks for your patience. I really don't want to mess this up again.
Click to expand...
Click to collapse
If you are rooted and can actually boot the phone then I would install Safestrap for MK2 and install TWRP 3.71 to use as the recovery. I've been using Safestrap and TWRP since I was on MF3. I have also successfully flashed the tar files through Odin to get to MK2 with no problems. If you are rooted then its a really good idea to use Safestrap with TWRP for a recovery. Afterward you can find a list of compatible roms that are specific for Touchwiz on MK2 that for the most part are pretty stable. The stock recovery on this phone is pretty much useless.
megamanDJ said:
...I would install Safestrap for MK2 and install TWRP 3.71 to use as the recovery... Afterward you can find a list of compatible roms that are specific for Touchwiz on MK2 that for the most part are pretty stable.
Click to expand...
Click to collapse
This is exactly what I did. I flashed the stock recovery in Odin (yes, it goes in the AP slot), which fixed my first problem. Then I installed Safestrap, then made a ROM slot and installed Goldeneye v. 21 (the 4.3 version for MK2). That removed all of the AT&T bloat (yay), and I did not have to flash the MK2 kernel (which I think would also have gone in the AP slot) because it has it already.
Then I flashed the GE add-on that removed a bunch of Samsung bloat (yay #2). Rebooted and turned off the rest of the Samsung stuff I didn't want. Got the phone up and running beautifully.
What a picky phone! The locked bootloader really causes a lot of trouble to inexperienced flashers like me. I unfortunately have about 5gb of "wasted" space because I understand I cannot flash over the "stock" rom, but I am at least running another ROM that I chose. My phone, my choice. Shame on Samsung!
Thank you very much!
kamikazees said:
This is exactly what I did. I flashed the stock recovery in Odin (yes, it goes in the AP slot), which fixed my first problem. Then I installed Safestrap, then made a ROM slot and installed Goldeneye v. 21 (the 4.3 version for MK2). That removed all of the AT&T bloat (yay), and I did not have to flash the MK2 kernel (which I think would also have gone in the AP slot) because it has it already.
Then I flashed the GE add-on that removed a bunch of Samsung bloat (yay #2). Rebooted and turned off the rest of the Samsung stuff I didn't want. Got the phone up and running beautifully.
What a picky phone! The locked bootloader really causes a lot of trouble to inexperienced flashers like me. I unfortunately have about 5gb of "wasted" space because I understand I cannot flash over the "stock" rom, but I am at least running another ROM that I chose. My phone, my choice. Shame on Samsung!
Thank you very much!
Click to expand...
Click to collapse
There is actually a way to flash a rom to the stock slot, but I haven't done it. Somewhere in the Safestrap threads explains how to do it. I think you can even get it back to normal if you change your mind.
So a few days ago i downloaded a rom for my Telus SGH-i337m which gave me apps and the features from the S5. I installed it and all that, but then it failed. So i tried to use my back up but it was corrupted as well. So I thought i can go online and find a stock image, i found many, but then I think i installed the image for a GT505 by accident. This gave me my software back but then i could't use my wifi or my data. So i found a proper SGH-i337m rom and installed it, my wifi came back but my data didnt. I thought it was because of the wrong modem, so i installed a few different modems and nothing worked. But today when i downloaded a different modem and installed it using odin mobile pro. It was installing and it rebooted, but then it got stuck there with the ODIN logo. I removed the battery and turned the phone on but not it says "Firmware upgrade encountered an issue..... please connect to kies". I tried connecting to kies but couldn't.
if someone could provide me with fully stock firmware and modem with easy instructions i would appreciate it, I'm so cheesed of my phone not working now
Did you have a custom recovery installed? Have you tried to go into recovery? Vol up home power. Make sure Samsung drivers are installed on your computer. Save a rom on your computer that you know works and place it on the sd card of your phone. Install rom. Try a stock rom version. Maple leaf by ib4stid would be a good one.
I just reread. Sorry I don't think my suggestion will help. Good luck.
Sent from Canadian i337m using Tapatalk
unsaddledhalo said:
if someone could provide me with fully stock firmware and modem with easy instructions i would appreciate it, I'm so cheesed of my phone not working now
Click to expand...
Click to collapse
http://www.sammobile.com/
~wolverine~ said:
http://www.sammobile.com/
Click to expand...
Click to collapse
I tried from here but still havent been able to succefully download any firmware
unsaddledhalo said:
I tried from here but still havent been able to succefully download any firmware
Click to expand...
Click to collapse
what do you mean? you need to create an account to be able to download. hope u got it sorted or by now
If you can give smoe more information about if you have a custom recovery installed (which one), can you connect to PC and move files to the external sd card, which modem you have installed and does the phone boot at all?
The procedure should be, root... download rom, ensuring it is for the i337m and not the i337 (2 different models) install custom recovery (I like TWRP (shouold be version 2.6 or lower.. some suggest 2.5 see mapleleaf rom OP..... others use Philz recovery... I don't have any experience with that).... install rom... let it boot up and run for a few minutes... then if you dont have the proper modem install the NC1 modem found on this forum...(I never flash the nonhalos file) I like to use Odin PC rather than moblie Odin... make sure you take off auto reboot as the flash takes longer than Odin allows before rebooting... You may need to enter your APN settings in settings... wrong APN's will result in no data...
As for roms, I would start with Maple leaf and see what you think... If you need to go back to stock, sam mobile roms are all Bell so you will see some Bell software (not to worry) and you will need to enter your APN's... then you can install a custom rom... again can't stress enough to choose one that is for i337m
The other thing you want to watch is bootloader versions.... once you go up in versions.. you can't go back...
Thanks for the help! I don't know how that I forgot the fact that I have a TelusS4 with a Wind sim in it, and cuz I formatted the phone and crashed the software, the bandwidths went to the stock Telus ones. But then I used a software and now I can use my wind sim on my phone!
Btw what are the best roms out there that look completely stock but provide tons of new features?
Sent from my SGH-I337M using XDA Premium 4 mobile app
unsaddledhalo said:
Thanks for the help! I don't know how that I forgot the fact that I have a TelusS4 with a Wind sim in it, and cuz I formatted the phone and crashed the software, the bandwidths went to the stock Telus ones. But then I used a software and now I can use my wind sim on my phone!
Btw what are the best roms out there that look completely stock but provide tons of new features?
Sent from my SGH-I337M using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Stock roms, I use Mapleleaf, I have also tried Google Play edition by Danvh but went back to maple leaf. I take it you are now back to stock and rooted, before you flash a rom, make sure you do a backup of your current stock rom so you have a easy way to go back. Make sure you back up your imei files also... might come in handy some day... I did both a full backup plus a seperate back up og just the iemi file... like i said before.... if you entend on going backwards from 4.4.3 or 4.4.2 to anything else do not change your bootloader... before you flash a rom make sure it will not change your bootloader... if it is going to i suggest you unzip the rom, remove the bootloader file and rezip then flash... it is up to you though... there is no going backwards on bootloaders......
So I have had a look and have seen things for rooted phones and for other phone models, but nothing yet for the S8. I have a UK (Three) phone that is otherwise unbranded with the exception of te boot animation showing the "3" logo rather than the Samsung one.
Is there a way of getting shot of the 3 boot animation (it looks rubbish) and having the Samsung one instead without root?
I have a Three UK S8 Plus too and want rid of this, as I've just got mine I haven't had chance to look around for a something (other than rooting, which I will be doing real soon anyway)
I was just looking for something that may just do it for now until I root, did you find anything ? I was maybe looking at some "bloatware" removal app /software, but does that remove the boot up screen horrible 3 logo ? Not sure..
just install stock firmware for this link: https://www.sammobile.com/samsung/g...SM-J320FN/BTU/download/J320FNXXU0ARH1/276931/ before you install firmware backup your phone with twrp. its just normal firmware with no three junk. if you wanna flash it 1. juts get the phone in download mode (find a tutorial for that 2. on your pc install odin flash tool and when your on the app plug in your phone into your pc and then click ap and then choose the firmware and then wait a sec and then click start and after the process is done it will say pass on the top and your phone should reboot and done your back to stockk i hope if it works
kindlefiledumper22 said:
just install stock firmware for this link: https://www.sammobile.com/samsung/g...SM-J320FN/BTU/download/J320FNXXU0ARH1/276931/ before you install firmware backup your phone with twrp. its just normal firmware with no three junk. if you wanna flash it 1. juts get the phone in download mode (find a tutorial for that 2. on your pc install odin flash tool and when your on the app plug in your phone into your pc and then click ap and then choose the firmware and then wait a sec and then click start and after the process is done it will say pass on the top and your phone should reboot and done your back to stockk i hope if it works
Click to expand...
Click to collapse
Hi I have tried this it doesn't work I am rooted how can o get rid of the 3 logo
I got a bricked Samsung Galaxy Note 4 (910F) vodafone branded.
it's totally broken I can't start it, can't go into recovery (the hardware buttons are OK).
I can only go into download mode.
tried flashing everything with odin back to stock. followed many different instructions and now I'm lost.
can someone tell me what exact files I need?
I think I have the right firmware downloaded BUT what about the bootloader? on sammobile under germany-vodafone there are so many different versions which one shall I choose?
AND: Do I need CSC? if so which one and where to find? Couldn't find it on sammobile.
And am I right with putting the bootloader under BL, the firmware under AP, the CP (whatever this is) under CP, the csc under csc?
repartition unchecked as I read somewhere.
I still don't understand what this "pit" file is for and I'm not sure if I have the right one.. never had a phone with sooo many different firmware files..
I'm used to flash via fastboot "recovery.img, boot.img, system.img" odin is a new thing for me
HELP PLEASEEE :'(
the reactivation lock is on.
nekrosmsk said:
I got a bricked Samsung Galaxy Note 4 (910F) vodafone branded.
it's totally broken I can't start it, can't go into recovery (the hardware buttons are OK).
I can only go into download mode.
tried flashing everything with odin back to stock. followed many different instructions and now I'm lost.
can someone tell me what exact files I need?
I think I have the right firmware downloaded BUT what about the bootloader? on sammobile under germany-vodafone there are so many different versions which one shall I choose?
AND: Do I need CSC? if so which one and where to find? Couldn't find it on sammobile.
And am I right with putting the bootloader under BL, the firmware under AP, the CP (whatever this is) under CP, the csc under csc?
repartition unchecked as I read somewhere.
I still don't understand what this "pit" file is for and I'm not sure if I have the right one.. never had a phone with sooo many different firmware files..
I'm used to flash via fastboot "recovery.img, boot.img, system.img" odin is a new thing for me
HELP PLEASEEE :'(
the reactivation lock is on.
Click to expand...
Click to collapse
The note 4 firmware is usually only 1 file that contains all you need. It contains the bootloader and CSC that you pick during download. Just pick the CSC for your country.
This is unless you get a 4 file repair firmware, which contains separate bootloader, system, and CSC files.
The pit file is only needed to repartition your device.
But with all off that aside, you state that your activation lock is activated. These means the phone was password protected.
If you tell me your country, I can at least point you to the correct firmware. So at least you'll know you got the correct one.
But as far as the activation lock, I can't help with that. "Google"
Edit. I now see you mentioned Germany Voda.
So here's the most current firmware for your device.
https://fws03.updato.com/GALAXYNOTE4/SM-N910F/TCL/SM-N910F_1_20171228192640_l5rw6mqv67.zip
Download and unzip.
Then if it's just 1 file that's .md5 then you put it in AP slot.
If it's 4 files put them in appropriate slots.
aaron74 said:
The note 4 firmware is usually only 1 file that contains all you need. It contains the bootloader and CSC that you pick during download. Just pick the CSC for your country.
This is unless you get a 4 file repair firmware, which contains separate bootloader, system, and CSC files.
The pit file is only needed to repartition your device.
But with all off that aside, you state that your activation lock is activated. These means the phone was password protected.
If you tell me your country, I can at least point you to the correct firmware. So at least you'll know you got the correct one.
But as far as the activation lock, I can't help with that. "Google"
Edit. I now see you mentioned Germany Voda.
So here's the most current firmware for your device.
https://fws03.updato.com/GALAXYNOTE4/SM-N910F/TCL/SM-N910F_1_20171228192640_l5rw6mqv67.zip
Download and unzip.
Then if it's just 1 file that's .md5 then you put it in AP slot.
If it's 4 files put them in appropriate slots.
Click to expand...
Click to collapse
This reactivation lock doesn't matter I found a solution how to bypass it when the phone is set up running android.
my question is, is it possible to flash firmware to the note4 at all with reactivation lock on? Or is that just an android thingy?
And yes please that would be nice if you show me the right firmware.
My model:
N910F GSMH
I believe it is vodafone branded because when it once worked it showed a vodafone logo while starting up.
my country is Germany.
I hope thats enough info :/
nekrosmsk said:
This reactivation lock doesn't matter I found a solution how to bypass it when the phone is set up running android.
my question is, is it possible to flash firmware to the note4 at all with reactivation lock on? Or is that just an android thingy?
And yes please that would be nice if you show me the right firmware.
My model:
N910F GSMH
I believe it is vodafone branded because when it once worked it showed a vodafone logo while starting up.
my country is Germany.
I hope thats enough info :/
Click to expand...
Click to collapse
I believe it should still flash with lock. If it isn't flashing something is wrong.
If you can't get Odin to flash that firmware try this and see what happens.
Download TWRP and flash it. Can you boot into recovery then? If so download a custom rom and flash it and see what happens.
TWRP: https://eu.dl.twrp.me/trlte/twrp-3.2.1-0-trlte.img.tar
Do you have Samsung drivers installed on PC? http://developer.samsung.com/common/download/check.do?actId=698
Do you have a good Odin? https://dl.sammobile.com/Odin3-v3.13.1.zip
aaron74 said:
I believe it should still flash with lock. If it isn't flashing something is wrong.
If you can't get Odin to flash that firmware try this and see what happens.
Download TWRP and flash it. Can you boot into recovery then? If so download a custom rom and flash it and see what happens.
TWRP: https://eu.dl.twrp.me/trlte/twrp-3.2.1-0-trlte.img.tar
Do you have Samsung drivers installed on PC? http://developer.samsung.com/common/download/check.do?actId=698
Do you have a good Odin? https://dl.sammobile.com/Odin3-v3.13.1.zip
Click to expand...
Click to collapse
I have the right latest samsung drivers installed yes.
I have the Odin version you just sent a link of. ( I also tried different older versions but no success).
I can't boot into recovery doesn't work. the hardware buttons are 100% working as I have to press vol+ to confirm to go into download mode.
I tried flashing TWRP and CWM both didn't work "custom recovery blocked by A/L error".
I can successfully flash firmware with Odin. It says "PASS" and then the phone reboots and is stuck on Samsung Logo. and sometimes it just shows blue text "recovery booting" but is stuck. nothing happens.
nekrosmsk said:
This reactivation lock doesn't matter I found a solution how to bypass it when the phone is set up running android.
my question is, is it possible to flash firmware to the note4 at all with reactivation lock on? Or is that just an android thingy?
And yes please that would be nice if you show me the right firmware.
My model:
N910F GSMH
I believe it is vodafone branded because when it once worked it showed a vodafone logo while starting up.
my country is Germany.
I hope thats enough info :/
Click to expand...
Click to collapse
Hey sorry the link you've sent doesn't work :/
aaron74 said:
The note 4 firmware is usually only 1 file that contains all you need. It contains the bootloader and CSC that you pick during download. Just pick the CSC for your country.
This is unless you get a 4 file repair firmware, which contains separate bootloader, system, and CSC files.
The pit file is only needed to repartition your device.
But with all off that aside, you state that your activation lock is activated. These means the phone was password protected.
If you tell me your country, I can at least point you to the correct firmware. So at least you'll know you got the correct one.
But as far as the activation lock, I can't help with that. "Google"
Edit. I now see you mentioned Germany Voda.
So here's the most current firmware for your device.
https://fws03.updato.com/GALAXYNOTE4/SM-N910F/TCL/SM-N910F_1_20171228192640_l5rw6mqv67.zip
Download and unzip.
Then if it's just 1 file that's .md5 then you put it in AP slot.
If it's 4 files put them in appropriate slots.
Click to expand...
Click to collapse
hey thanks in advance, but this link doesnt work it says "hotlinking is not cool". anyways I searched the firmware for my model number on this site and applied the "germany vodafone" filter. but there are still soo many different entries which one shall I choose? The latest date?
nekrosmsk said:
hey thanks in advance, but this link doesnt work it says "hotlinking is not cool". anyways I searched the firmware for my model number on this site and applied the "germany vodafone" filter. but there are still soo many different entries which one shall I choose? The latest date?
Click to expand...
Click to collapse
Here's webpage
https://updato.com/firmware-archive-select-model?record=58770125168D11E89F15FA163EE8F90B
After you flash, how long are you waiting for it to boot?
Sometimes it takes awhile.
aaron74 said:
Here's webpage
https://updato.com/firmware-archive-select-model?record=58770125168D11E89F15FA163EE8F90B
After you flash, how long are you waiting for it to boot?
Sometimes it takes awhile.
Click to expand...
Click to collapse
Thanks for the link I'm downloading.
After flashing odin says PASS and my note 4 reboots. then there are 2 cases which in my view appear randomly. Either it shows the samsung logo and is stuck.
OR it shows the samsung logo and a blue little text in the upper left corner saying "recovery booting" and is stuck. I waited like 5 minutes. shall I wait longer? :/ hm..I'll try
OH and sometimes the screen just goes black idk if it really turns off after getting stuck on samsung logo.
Pull the battery, leave it out for 10+ minutes
Put battery back in
Boot to download mode (Power + Vol Down + Home)
Then try (re)flashing stock ROM via odin, i would try the earliest you can find to have the best chance, you can always flash a later one if you get it running
Better range of ROMS from sammobile, i never use updato for that reason: https://www.sammobile.com/firmwares/galaxy-note4/SM-N910F/VD2/
If none of that works, then its likely you have a hardware fault ...emmc or other
stylemessiah said:
Pull the battery, leave it out for 10+ minutes
Put battery back in
Boot to download mode (Power + Vol Down + Home)
Then try (re)flashing stock ROM via odin, i would try the earliest you can find to have the best chance, you can always flash a later one if you get it running
Better range of ROMS from sammobile, i never use updato for that reason: https://www.sammobile.com/firmwares/galaxy-note4/SM-N910F/VD2/
If none of that works, then its likely you have a hardware fault ...emmc or other
Click to expand...
Click to collapse
So I tried flashing. after flashing OH WONDER it said recovery booting and then it showed this green android logo thing with a rotating icon in it "you know what I mean" but then it stopped and just turned off.. I could freak out really.. I tried flashing again. same issue. I could then press the recovery mode key combo to get into this rotating android logo screen but everytime it just freezes and turns off. yes the battery is fully charged before I started flashing this firmware now. I flashed the one u said the earliest. So Now I tried the one the other guy here showed me. didn't work either. it just gets stuck at samsung logo. I found a repair firmware for my model containing (pit, bl, ap, cp, csc and odin) I flashed all but odin fails "write error". I then tried odin v3.0.7 but then it got stuck while flashing the system image. I waited like 1 hour. nothing. tried it again. nothing it freezes on the same position. I then tried the same on the latest versions of odin v3.12.3, 3.12.7 and on 3.13.1 but it also freezes on system.img.ext4 image flashing..
nekrosmsk said:
So I tried flashing. after flashing OH WONDER it said recovery booting and then it showed this green android logo thing with a rotating icon in it "you know what I mean" but then it stopped and just turned off.. I could freak out really.. I tried flashing again. same issue. I could then press the recovery mode key combo to get into this rotating android logo screen but everytime it just freezes and turns off. yes the battery is fully charged before I started flashing this firmware now. I flashed the one u said the earliest. So Now I tried the one the other guy here showed me. didn't work either. it just gets stuck at samsung logo. I found a repair firmware for my model containing (pit, bl, ap, cp, csc and odin) I flashed all but odin fails "write error". I then tried odin v3.0.7 but then it got stuck while flashing the system image. I waited like 1 hour. nothing. tried it again. nothing it freezes on the same position. I then tried the same on the latest versions of odin v3.12.3, 3.12.7 and on 3.13.1 but it also freezes on system.img.ext4 image flashing..
Click to expand...
Click to collapse
Try the Samsung Smart Switch for PC - like this : https://www.youtube.com/watch?v=9QhJngOuLQ4&t=337s
Good luck, maybe it will work - for me it did work for the 910C.
w41ru5 said:
Try the Samsung Smart Switch for PC - like this : https://www.youtube.com/watch?v=9QhJngOuLQ4&t=337s
Good luck, maybe it will work - for me it did work for the 910C.
Click to expand...
Click to collapse
doesnt work. I tried several versions of smartswitch AND samsung kies. nothing works it always says my model is not supported. I reinstalled drivers. tried on another pc. tried another usb port. yes I'm using the original stock usb cable. model not supported. But I've also read that in other threads that the 910F model seems to be unknown by kies or smartswitch. I'm rly starting to hate samsung now. I have never ever had so many problems with flashing and so on.
nekrosmsk said:
So I tried flashing. after flashing OH WONDER it said recovery booting and then it showed this green android logo thing with a rotating icon in it "you know what I mean" but then it stopped and just turned off.. I could freak out really.. I tried flashing again. same issue. I could then press the recovery mode key combo to get into this rotating android logo screen but everytime it just freezes and turns off. yes the battery is fully charged before I started flashing this firmware now. I flashed the one u said the earliest. So Now I tried the one the other guy here showed me. didn't work either. it just gets stuck at samsung logo. I found a repair firmware for my model containing (pit, bl, ap, cp, csc and odin) I flashed all but odin fails "write error". I then tried odin v3.0.7 but then it got stuck while flashing the system image. I waited like 1 hour. nothing. tried it again. nothing it freezes on the same position. I then tried the same on the latest versions of odin v3.12.3, 3.12.7 and on 3.13.1 but it also freezes on system.img.ext4 image flashing..
Click to expand...
Click to collapse
afaik the "repair" fimeware is no better than flashing a stock ROM in one file...
its startng to sound like a hardware error, if it cant even write to the dvice theres really not many (probably any) options left.
ive purposely bricked a phone and recovered it (not recommended of course), ive never had or never saw as much effort youve put in to try and recover a phone...
stylemessiah said:
afaik the "repair" fimeware is no better than flashing a stock ROM in one file...
its startng to sound like a hardware error, if it cant even write to the dvice theres really not many (probably any) options left.
ive purposely bricked a phone and recovered it (not recommended of course), ive never had or never saw as much effort youve put in to try and recover a phone...
Click to expand...
Click to collapse
me neither.. can't believe this.. how can a phone be physically damaged by flashing? paid 70 bugs for a note 4 with a software issue.. as I often do. recovered dead phones from sony, xiaomi, wiko, asus, lg, huawei etc... adb, fastboot and u good to go. odin is killin me.. gonna sell it as bricked.
Cleared caches?
R0B3RTF1SH3R said:
Cleared caches?
Click to expand...
Click to collapse
HOW? If I can't boot into recovery mode?