Related
We all know how fun flashing a new rom is... and we also know how painstaking it is to reinstall all the apps again.
So I was looking around XDA to find how to automatically install apks saved on PC, and I found a couple of nifty solutions - including a full blown GUI app to backup/rename/reinstall apps & data. Unfortunately, it didn't work for me so good. Hence, decided to go the command-line route. Found a few commands and wrote a script that automatically creates a list of apks in the directory and installs it in your device via adb.
Note :
1. If you are a GUI person, you're better off without this one.
2. I wrote this one all by myself with help from this thread : http://http://forum.xda-developers.com/showthread.php?t=743457
3. I'm not a developer. Yet I decided to share this one as i found it extremely helpful, and hopefully it may help someone else somewhere. Plus, this is my first thread, so in case I missed a few etiquettes, I apologize in advance. :angel:
Install From PC :
1. Device on and running, with Android Debugging Enabled.
2. Make sure your PC can connect with your device (use "adb devices" command, adb should be usable system-wide)
3. Collect all your apks in one folder (say C:\Apps)
4. Download & Extract the attached zip and put installPC_v1.bat file inside your apks' folder (here C:\Apps)
5. Double click on the batch file.
6. Done.
Note :
1. You can view which app is being installed and status reports of all previous apps in the command prompt that appears.
2. To make adb usable system-wide, just include it in the path System variable in Control Panel.
3. My "Verify apps over USB" in Developer Options and Security Check in Google Settings were Disabled. This may or may not affect the installation process.
4 This is the first version and it should work without hassle if your setup is fine, but I haven't included any error handling or any "extra" features. Also, haven't rigorously tested on multiple devices. It works on my Win 10 64-bit and Note 4 (with both Touchwiz and AOSP). Just give it a go :fingers-crossed:
Managed to soft brick my Note 4. Set my dpi to 200, and my resolution to 720p. Apparently, it's just too low. Worked great when I set the values, but restarting the phone caused the brick. (It boots, but can't access anything. Unfortunately, I don't have my PC allowed as ADB, so I can't even connect from that state to ADB.)
So.
My idea to prevent full wipe, is to use ADB sideload OR ORS.
- Sideload. Make a "payload" that will replace the build.prop with the stock one.
- ORS. http://wiki.rootzwiki.com/OpenRecoveryScript
How do I actually do this?
Like the RecoveryScript seems to be a great idea, but from TWRP, I could not find a single build.prop file at all. There is a default prop, but it contains no resolution, dpi or whatever.
So I spent another few hours on this. I hate myself. And I hate the app's developer for being so careless.
- Flashed latest Samsung firmware hoping it will kill the software. Nope. It did not.
- Flashed the .zip for build.prop. NO effect.
The system has the correct DPI value so it must not be the issue.
- I think the app auto runs, and sets resolution. So I tried grep, but it cannot find the "1280" string anywher,e and I also removed the app from /data/app and /data/data.
- I cannot get MTP or ADB working in TWRP whatsoever. Huge letdown, but there is just no support. And without seeing what happens on the screen (it must be just my lockscreen there), I can't accept ADB connections either.
Well, so I went YOLO and cleared data. And... behold, NOTHING.
Did this retarded stupid program killed my phone? Holy hell.
Okay, so full entire wipe + reflash + full wipe, and now it works.
This app? Never again. The others are good on the market, so go for it.
App in question: https://play.google.com/store/apps/details?id=com.chornerman.easydpichanger
[ DO NOT USE !!! ]
Instead of wipes at Restore DPI: You can remove only of "com.android.providers.settings" at "/data".
Sorry but I have to resurrect this. I've played with dpi settings and now after reboot I cannot press enter when I type in my password as keyboard is partly off screen. TWRP is not working as it does not support Android 12. Any chance to resolve this beside flash?
Update: Connected keyboard via OTG cable and managed to unlock
Resurrecting this to offer another solution that doesn't involve any wiping/flashing/restoring-to-stock or messing with build.props
I used the same app as OP and feared the worst when I got stuck on recovery after changing DPI
This method allowed me to restore my xiaomi Redmi 9 with android 10
-You need to have a custom recovery installed
-"shell wm" commands don't work in recovery
You need to edit settings_global.xml & settings_secure.xml found in /data/system/users/0
You can do this by pulling&pushing the files to a PC using adb or editing in recovery using nano editor or something similiar.
Search for:
"display_size_forced" in settings_global.xml
"display_density_forced" in settings_secure.xml
Edit those with something close to your default values, then reboot and that's it!
Now that you're no longer stuck in boot you can reset resolution and density with the usual methods like adb or a better app
I hope this helps anyone else stuck in the same problem I was
mrmrva said:
...TWRP is not working as it does not support Android 12. ......
Click to expand...
Click to collapse
Where did you get a A12 version for which Note4?
Owning a N910F=trlte I don't find any higher than A11.
Don't have Samsung but Poco f2 pro and was looking for solution everywhere so posted here.
[GUIDE/TUTORIAL/HOWTO] HTC One M7 Stock to Android 11 / LineageOS 18.1
[GUIDE/TUTORIAL/HOWTO] HTC One M7 any version (m7, m7ul, m7spr, m7vzw) stock to Android 11 R / LineageOS 18.1
This detailed step-by-step guide helps you transform your HTC One M7 (any version) to a powerful one with Android 11.
Make sure you have the One M7 model, in Android, go to Settings > About phone and check the model.
CHANGELOG
v8. Upgrade to Android 11, improve readability, update pack
v7. Updated pack with MagiskManager 8.0.7 and Magisk 21.4
v6. Infos in case of Simlock
v5. Moved to Android 10 thanks to @tarkzim, updated pack with Magisk 20.4
v4. Moving to Android 9. I was wrong in v3 ;- Thx @tarkzim), good for all M7 versions
v3. Reverted back to Android 7.1. No stable ROM for Android 8 or 9 (and will never be)
v2. Tutorial updated for Android 8.1 Oreo, updated pack with TWRP 3.3.1-0
v1. Initial release
1) DOWNLOAD
- djibe HTC One M7 pack (44.3 Mo) v2 : http://bit.ly/djibe-onem7-v1
(includes HTC drivers, recovery TWRP 3.6.1_9-0 for all m7 by Xeno1, Magisk Root 23 adb & fastboot.exe).
Unzip the djibe folder from the zip on root folder of C: drive.
- ROM Unofficial Lineage OS 18.1 for M7: https://forum.xda-developers.com/t/rom-11-0-unofficial-m7-all-lineageos-18-1-stable.4454219/
Download latest build for M7 here: https://androidfilehost.com/?w=files&flid=334598&sort_by=date&sort_dir=DESC
+ BitGApps ARM 11 v1.4+: https://github.com/BiTGApps/BiTGApps-Release/releases/
+ Charge phone to 100 %
WARNING. This tutorial uses Microsoft Windows.
WARNING. Warranty is now void.
WARNING. Read carefully the sentences starting with ###.
2) BACKUP DATA AND INSTALL DRIVERS
Disable Antivirus.
Install drivers from my pack:
right click on HTCDriver.exe -> click on Run as administrator and continue the setup.
Then install HTC_BMP_USB_Driver_x64.msi (or *_x86 if you have a 32bits Windows edition).
### Install doesn't work ? Try these drivers for Win10 : https://htcusbdriver.com/download/htc-usb-driver-v4-02-0-001
Now go to my folder flash, and right click the adb 15seconds installer > Run as administrator.
During install, every time the command asks you a confirmation, enter Y and confirm with Enter.
Connect HTC One (while phone on) to PC, let drivers install.
In Windows explorer, HTC One should be available.
### If not make sure phone connection is in File transfer mode (see Android notifications).
Collect all personal photos, videos, etc ... and copy these on PC.
Use an app like Backupyourmobile to backup texts, contacts, etc.
Check that backup is located on microSD card.
Then copy the backup on your PC.
Disconnect phone.
### If your phone is Simlocked/carrier locked/Network locked, don't go further.
Visit official website of your network carrier (or call their support) to retrieve your desimlock code.
Ask them for details on how to remove simlock.
How do I know my phone is simlocked ? When you insert a SIM card from another operator, network is not accessible.
Only a stock ROM can remove simlock.
To go back from custom ROM to stock in 1 zipfile flash, follow this tutorial: https://tcg96.github.io/m7gurureset
3) UNLOCK BOOTLOADER
In Android, go to Settings > About > Software information > More.
Tap 7 times on Build number. It unlocks Developer options.
Go back to the About menu, you can see the new Developer options menu.
Tap on it, accept the warning.
Toggle on the USB debugging option.
Connect phone, a message appears on phone : Allow USB debugging?
check Always allow and confirm by tapping on OK.
Now, open a Windows command on my "flash" folder (hold Shift + right click on folder -> Open a windows command here).
### Then navigate to my flash folder (if it is on desktop) with this command :
Code:
cd /d C:\djibe\flash
Enter command :
Code:
adb devices
, confirm by pressing Enter.
Command returns :
Code:
List of devices attached
HT35****** device
### If no device is found, uninstall and reinstall properly the drivers while antivirus is off.
### Or start fresh on another PC.
Now type :
Code:
adb reboot bootloader
Authorize ADB commands on phone.
Phone restarts in Fastboot mode. Wait till phone screen is blank in fastboot mode.
Type :
Code:
fastboot devices
Command returns :
Code:
HT35**** fastboot
Type :
Code:
fastboot oem get_identifier_token
, confirm by pressing Enter.
Command returns multiple lines.
Select with your mouse all the lines from
Code:
<<<< Identifier Token Start >>>>
(included)
to the line
Code:
<<<<< Identifier token end >>>>>
(included).
Now on keyboard copy (Ctrl + C combo), then open Notepad.
In Notepad, paste those lines (Ctrl + V combo).
Now manually remove all the (bootloader) strings from each line.
Your notepad should now look like this :
<<<< Identifier Token Start >>>>
37A5DBF4FE5F0D9F4425E54AA91AFDBF
2A20E9C67C3BB4FAE60263F76BDEC6AC
847BF9FFB11DAEA4AB88AC8710435449
9BC12E93DF4C54FFE3D064C4C810C49A
2CDAF2E0CD3A164FED4A568CB0FD2AC6
C01AA991733D949C00987062D691DE91
8AA1C97CEBC3ACE83FECE75A1D03CE72
62414C7DC36A73AFCBF433E1EBE2EDC7
E272F73309632D3EF8C86E472B65E8EF
37E46B52FE3F94FC69D1854CA3DE6F48
C3E10001B233A70B1EAF35134F51FCC6
353E0CC98534E6E60A241A7063D0BE2F
A5B752E75C1C47E6F739BDBE67D024DA
3292A14278247557632639802722A86C
E61424F7666AE085AA9905096FEED1AD
5ECBBD867544E95ABDDA277690B8CB55
<<<<< Identifier Token End >>>>>
Now visit this website : https://www.htcdev.com/bootloader/
Register on the site. Confirm registration with your email.
In the select menu, chose HTC One (M7), click Begin unlock Bootloader button.
Agree to legal terms.
Next page, go to the bottom and click continue to step 5.
In the bottom of this page, in the lower textarea "My Device Identifier Token",
copy and paste the multiple lines you just edited (my example is just above).
Click Submit.
HTC tells you : Token Submitted Successfully.
Open your mailbox (associated to your HTC account).
Copy the Unlock_code.bin file attached to email in my "flash" folder you unzipped.
In Windows command, type :
Code:
fastboot flash unlocktoken Unlock_code.bin
, confirm with Enter.
Command should return :
Code:
unlock token check successfully
Back to phone, press Volume+ to select "Yes, unlock bootloader", then Power button to confirm flash.
Now wait while phone is going to Factory reset.
Don't let Android restart by holding both Power + Volume- to enter bootloader immediately.
FASTBOOT menu is overlined in red.
4) FLASH TWRP RECOVERY
Using the same Windows command prompt, enter :
Code:
fastboot devices
to make sure phone is still available.
Then
Code:
fastboot flash recovery twrp-3.6.1_9-0-m7univ.img
Command returns :
Code:
finished. total time: x.xxxxs
##€ If it fails, tries with a Windows Powershell shell.
Now on phone, press Volume- to select Bootloader, confirm with Power button.
You are back to the booloader screen (UNLOCKED is written on top line), press Volume- to navigate to RECOVERY, and confirm with Power button.
Phone reboots in TWRP recovery.
5) WIPE PARTITIONS
In TWRP, check Never show this screen and Swipe to Allow Modifications.
You land on TWRP Home screen.
Go to Wipe > Advanced wipe.
Select Dalvik, Cache, System, Data, Internal Storage then Swipe to Wipe, go back to Wipe menu.
6) FLASH ROM, GAPPS AND ROOT (OPTIONNAL)
We first have to get our zips on the phone.
Still on TWRP Home screen, tap on Mount > deselect all partitions except Data, then connect phone to PC.
In Windows Explorer, you can see MTP Device, copy the zips of ROM, GApps, Magisk + Magisk Manager right in the Internal Storage folder.
Tap on Disable MTP once copy is finished.
Then back to Home screen, tap on Install > choose lineage*.zip,
(if you don't see the files, tap on Select Storage and make sure Micro SDCard is active)
then Add more Zips -> Magisk*.zip,
then Add more Zips -> bitgapps*.zip,
then Swipe to confirm Flash.
Wait for operation to end (can be long).
When completed successfully, tap on Reboot.
Tap on Do not install when TWRP asks for the app install.
Wait during long first boot.
Setup Android.
7) You can use Backupyourmobile to restore data,
use GPS Status & Toolbox app to enhance GPS fix.
That's it.
Enjoy,
djibe
THANKS --------------
Teams of : TWRP, LineageOS team, tarkzim, zsoerenm, alray, ., Flyhalf205, icxj1, R1ghtC, gimmeitorilltell, All M7/MSM8960 contributors.
Just my 2 cents
Just my 2 cents if it can help
djibe89 said:
- a microSD card (FAT32 format). Copy the zips of ROM, GApps, addonsu and deviceid*.apk (both in my pack) on the root folder of microSD, then insert it in phone.
Click to expand...
Click to collapse
The M7 is not equipped with a mircoSD card slot, only a virtual /sdcard (symlink to /data/media/0) ... So they'll either have to adb sideload or adb push the files to internal memory which is pointless at this stage since it will be wiped during bootloader unlock. Or drag n drop the files using mtp from twrp once it's installed on the phone.
3 ) UNLOCK BOOTLOADER
[...]
Now wait while phone is going to Factory reset.
Setup Android again on next boot.
4 ) FLASH RECOVERY
Now re-enable USB debugging in Android.
Using the same Windows command prompt, type
Code:
adb reboot bootloader
again.
Click to expand...
Click to collapse
You could save a lot of time just force rebooting to bootloader (power + vol down) right after BL unlock/factory reset are completed so you don't have to setup the system you're going to wipe 2 steps later. USB debug anyway isn't required to fastboot flash recovery so it's not like booting back in system is mandatory before flashing recovery.
:good:
@alray : Thank you so much for help.
I'm lazy with baby waking up every night and did some awful copy-paste.
I correct all these right now.
Thanks.
I would highly recommend to use the official downloads of twrp, HTC drivers, roms and so on, you uploaded these files to your google drive and there is stuff in it nobody will ever need. And nobody knows if those files are in original condition. Strange thats the third time this year someone tries to get users to use their stuff (for a five years old device) there are already a lot of guides out there and several thousand people did it several thousand times without problems. Also you wrote that this would be official lineage but its unofficial, and for that there is already a thread here. The other two threads got deleted by mods because they tried to get users to use files from unknown suspects sources. Use android file host and maybe tell in los thread where those files are stored, whats the source and who made it.
saturday_night said:
I would highly recommend to use the official downloads of twrp, HTC drivers, roms and so on, you uploaded these files to your google drive and there is stuff in it nobody will ever need. And nobody knows if those files are in original condition. Strange thats the third time this year someone tries to get users to use their stuff (for a five years old device) there are already a lot of guides out there and several thousand people did it several thousand times without problems. Also you wrote that this would be official lineage but its unofficial, and for that there is already a thread here. The other two threads got deleted by mods because they tried to get users to use files from unknown suspects sources. Use android file host and maybe tell in los thread where those files are stored, whats the source and who made it.
Click to expand...
Click to collapse
Because you are a senior member you know where to download everything.
But everyone is not like you.
So I tried to compile a ready-to-go pack for the newcomers, like I did for many devices by know.
This allows noobs to profit from custom ROMs and don't keep it esoteric.
Like you say, many downloads are just hacks, so I tried to bundle lowest size safe files.
saturday_night said:
I would highly recommend to use the official downloads of twrp, HTC drivers, roms and so on, you uploaded these files to your google drive and there is stuff in it nobody will ever need. And nobody knows if those files are in original condition. Strange thats the third time this year someone tries to get users to use their stuff (for a five years old device) there are already a lot of guides out there and several thousand people did it several thousand times without problems. Also you wrote that this would be official lineage but its unofficial, and for that there is already a thread here. The other two threads got deleted by mods because they tried to get users to use files from unknown suspects sources. Use android file host and maybe tell in los thread where those files are stored, whats the source and who made it.
Click to expand...
Click to collapse
For the official LOS ROM, tell LOS to store official builds. As they don't do it anymore, we must rely on personnal builds.
A lot of guides out there ? Made extensive search for cracking this phone, never found a step by step one.
Five year old device ? Still so good once unleashed. Custom ROMs are for these devices isn't it ?
@djibe89 Might be useful to point out in your opening post that the 20180420 build has DT2W enabled, but I'd like feedback from people with a functional battery if it makes their device reboot or not, similar to issues reported in the original kernel thread. I suspect my battery is on its way out. The 20180416 build is completely stock upstream LineageOS, no DT2W.
Thanks for the credit .
.:B:. said:
@djibe89 Might be useful to point out in your opening post that the 20180420 build has DT2W enabled, but I'd like feedback from people with a functional battery if it makes their device reboot or not, similar to issues reported in the original kernel thread. I suspect my battery is on its way out. The 20180416 build is completely stock upstream LineageOS, no DT2W.
Thanks for the credit .
Click to expand...
Click to collapse
Thanks for your explanations.
Any trouble following this tutorial guys ? How to enhence it ?
802D device supported?
M.Z.F said:
802D device supported?
Click to expand...
Click to collapse
Hi, no idea, does your model has another model name/code ?
djibe89 said:
Hi, no idea, does your model has another model name/code ?
Click to expand...
Click to collapse
Model name & code like?
PRI Version= 4.22_001
PRL Version = 10012
Getting this message: Updater process ended with ERROR: 7 Error installing zip file '/sdcard/lineage-14.1-20180520-UNOFFICIAL-m7.zip'
any help would be appreciated, thank you
I have tried all the custom roms mentioned above i.e. lineage os , Xenonhd and slim7. But non of them installed. It always shows error either this is not for your device , this device is cdwg or unable to mount. Please give me a link for custom rom for my device that is htc one 802d cdwg
Rafay106 said:
I have tried all the custom roms mentioned above i.e. lineage os , Xenonhd and slim7. But non of them installed. It always shows error either this is not for your device , this device is cdwg or unable to mount. Please give me a link for custom rom for my device that is htc one 802d cdwg
Click to expand...
Click to collapse
All the custom roms mentioned above are NOT for your phone variant.There were almost no development for the 802 branch at the peak of it's popularity and I didn't see anything new for this variant in the past 2 years or so. I wouldn't expect a 7.1 roms for this variant...
Maybe you'll have better luck searching on Asian forums
skovatov said:
Getting this message: Updater process ended with ERROR: 7 Error installing zip file '/sdcard/lineage-14.1-20180520-UNOFFICIAL-m7.zip'
any help would be appreciated, thank you
Click to expand...
Click to collapse
Here you have answer:
https://forum.xda-developers.com/showthread.php?t=2522762
---------- Post added at 05:30 PM ---------- Previous post was at 05:20 PM ----------
Hi.
After installing Android 7.1 Google Pay stop working on my phone. I have torn on NFC communication but terminal don't read my card from app. I don't turn on access to root. Any aidia how to solve this issue?
I have an M7 that I would like to update Android on however the above is a bit over my head. I have seen other sites and video showing this to only take a few minutes and not requiring a PC. Am I missing something? I just don't quite understand the process of it all.
Bazooka said:
I have an M7 that I would like to update Android on however the above is a bit over my head. I have seen other sites and video showing this to only take a few minutes and not requiring a PC. Am I missing something? I just don't quite understand the process of it all.
Click to expand...
Click to collapse
Flashing without a PC can be done but not recommended. If something goes wrong (and thrust me, it happens pretty often) you'll be stuck with a bootlooping phone.
The guide at post #1 is all you need, what part exactly do you have problem understanding?
alray said:
Flashing without a PC can be done but not recommended. If something goes wrong (and thrust me, it happens pretty often) you'll be stuck with a bootlooping phone.
The guide at post #1 is all you need, what part exactly do you have problem understanding?
Click to expand...
Click to collapse
Thanks for that. I tried to go through it nice and slow making sure I understood each step. I got to where I needed to open a command window on the "flash" folder to which I must have powershell(?) installed as it gave me that option. After inputting 'adb devices' it listed a device but stated it was offline. This is where I am stuck as the steps after this do not work.
drivers win10
Hi, I have a basic ask. Do you know where to get Win 10 drivers? I can't run the installer HTCDriver_4.2.0.001 on my Windows 10 (version 1803).
It gives me the error: The driver installer is not supported for your operating system. Thanks for your help.
This one20092011201220132015201720192021Nook v1 Nook Simple TouchNook Simple Touch w/ GlowlightNook GlowlightNook Glowlight PlusNook Glowlight 3Nook Glowlight Plus (7.8 inch)Nook Glowlight 4
The other one
The 2019 Glowlight Plus shares the same name as the 2015 release. To avoid confusion, people began referring to it as the Glowlight 4, a name later used for the 2021 Nook release (surprisedpikachu.jpg). While the 2019 Nook is both confused with the 2015 and 2021 Nooks, it is less common than either. This makes it difficult to find compatible resources and tutorials.
This thread is for collecting the available resources for the 2019 Nook in one place, and eventually building a step-by-step guide for unlocking the potential of the device.
Why the BNRV700?
Three years after its release, it's currently the cheapest option for a reader with a screen size ideal for large format PDFs, such as textbooks. As of writing, the Nook Glowlight Plus (2019) can be found for half (or less) the price of other options with a similar display.
Unfortunately, the Nook ships with poor support for PDFs, sluggish hardware, severely outdated firmware (Android 4.4.2, released 2013) and lacks additional features like expandable storage. Some of these issues can be remedied, meaning the Nook could be a great option for many people, but only if it's safe and convenient to expand its functionality.
If you know of any useful resources or guides, please leave them in the comments below.
Note: This is an early work in progress. As of writing this, I don't have the device yet.
I'm reserving this space to put any resources, or document my experience with rooting or recovering the Nook Glowlight Plus 7.8 2019 (NGP7.8, BNRV700).
Resources
Technical
Hardware overview: TemblastBackup and Recovery
TWRP: GithubNeo Noogie: Temblast, XDA-threadRooting
Magisk Root guide (Glowlight 4): Mobileread-threadCaution: This guide is specifically for the Glowlight 4 (2021) rather than the Glowlight Plus 7.8 (2019) but it might be applicable.RootGLP-3 script (Glowlight 3): XDA-threadCaution: This resource is for the Glowlight 3 (2017) rather than the Glowlight Plus 7.8 (2019), however it has been reported to work.RootGLP-3 script (2019 Glowlight Plus): XDA-threadNote: This is a small modification of the Glowlight 3 (2017) root script for the 2019 Glowlight Plus, from wgznz (Chinese).Firmware
Alternate ROM: XDA-threadSoftware
Installing a launcher:Installing apps:Compatible readers and utilities:Adding wallpapers:Adding a software back button:Physical button remapping:Hardware
Expandable storage mod::
High risk or incompatible resources
Mods
NGP Exposed module with fast refresh: Mobileread-threadSupported: Nook Glowlight Plus (2015), Nook Glowlight 3Notes: Due to the similarities between the NG3 and NGP7.8 (2019), someone might be able to get this to work, but it's untested.
jun127 said:
I think more people would be willing to try it. But, between confusing and inconsistent naming making searches difficult (now even worse with the "Glowlight 4") and a lack of step-by-step guides, it's a minefield for the casual user to modify, and most aren't interested in the sub-standard Nook software.
Click to expand...
Click to collapse
I don't know whether you saw this and then dismissed it or just missed it: https://forum.xda-developers.com/t/gp-g3-gp7-8-twrp-alternative-firmware.4074347/
Seems like that might address most of the issues you have expressed.
nmyshkin said:
I don't know whether you saw this and then dismissed it or just missed it: https://forum.xda-developers.com/t/gp-g3-gp7-8-twrp-alternative-firmware.4074347/
Seems like that might address most of the issues you have expressed.
Click to expand...
Click to collapse
It looks like it could be a useful resource, but it seems like a lot of steps and cautions are ommitted. Although I've installed TWRP, rooted, and installed the fastink kernel (among other mods) on my old NST, I would hesitate (especially as a new user) to install alternate firmware without a clear procedure to first backup and revert everything to factory defaults or recover if something goes wrong.
Rough draft / work in progress (proceed at own risk)
Getting started
Download and install ADB
Using Android Studio
1: Download Android Studio
2: Scroll down and click on “SDK Tools Only”
3: Click on “ADB, Fastboot, and Platform Tools” and then click on the “Download” button.
4: After “adb_setup-x86.exe” is downloaded by the installer, run it and install adb inside the android SDK folder.
Using Minimal ADB and Fastboot
1: Download the installer or portable version (See: original XDA thread, latest version 1.4.3, 2018).
2: Install and run
Note: If you use the portable version, commands should be ran from the same directory. To open a console in the current folder on Windows, select the address bar, type cmd and hit enter.
Enable USB debugging through developer options
1: Unplug the nook from the computer and turn the Nook on, register an account with Barnes and Noble and finish setting the device up.
2: Pull down the top menu
3: click "see all settings"
4: Press the down error on the bottom of the menu to go to the second page of settings
5: Press "about"
6: Tap the Nook logo until developer mode is enabled
7: Press "developer option settings"
8: Enable the "usb debugging" option
9: Connect the Nook to your computer. A popup will appear on your Nook asking to "turn on USB mode to safely move files..." click OK.
Note: This will cause your computer to download the appropriate drivers. After the drivers have been installed your Nook will show up in Windows Explorer and the Device Manager.Note: When running commands over USB, sometimes it's necessary to temporarily disable mass transfer mode. To do this, go back to the developer options menu and select "disable mass storage".Important: Remember to re-enable mass storage mode if you would like to drag-and-drop files onto your device using Windows file explorer later.
Backup and restoration
The two most popular methods of creating and restoring backups are TWRP and Neo Noogie. If possible, it's best to have a backup from both. However, if you're not comfortable using the command line in Windows, you may choose to use TWRP only. Neo Noogie is a more powerful (complete) backup method, but it's easy to accidentally format your device or write a backup to the wrong Windows drive, either of which could be a nightmare.
TWRP is recovery software that is installed to the device, and provides a menu to backup and restore parts of the device to internal memory. You'll have to copy the recovery files from your device afterwards.
Neo Noogie can either be installed like TWRP or booted with fastboot. When booted into Neo Noogie, the entire flash memory is served to Windows and appears as a raw unformated drive. The internal storage can then be copied with special software. This has the advantage over TWRP in that it can be used to backup every aspect of your device, but you have to be very careful not to accidentally format the drive in Windows, as it could brick your device.
TWRP
Download TWRP
1: Download twrp_quill.img (may, 2020) from https://github.com/Ryogo-Z/nook_ntx_6sl_twrp/releases
2: Move twrp_generic to a folder (such as Documents\Nook)
Install TWRP
3: Power the NOOK BNRV700 off.
4: Hold the U button and then the power button until it starts into fastboot mode.
5: Connect the Nook to a Windows computer with USB, the drivers should be installed automatically.
6: Open the command prompt or Minimal ADB and Fastboot
7: Navigate to the folder you saved the TWRP image in (ex. starting from your user directory, enter "cd Documents\Nook").
8: Enter fastboot flash recovery twrp_generic.img to install TWRP
9: Enter adb reboot recovery (or interrupt startup 5 times) to enter TWRP recovery mode
Create backup with TWRP
Notice: (TWRP will not backup /storage/spsd as well as /data/media, which in practical terms means ...xyz...)
1: (I don't have a Nook anymore as my NST screen isn't working and haven't used TWRP in 10 years. I imagine it's something like boot into recovery/TWRP > Backup > check all the options > run)
2: Plug the Nook into the computer
3: Select USB mass transfer protocol
4: Open the Nook in file explorer and find wherever the recovery was saved to
5: Copy it to a safe place, like documents\nook.
Uninstall TWRP / reinstall stock recovery
The Nook's update file, 'update.zip' contains a copy of the stock recovery which can be reinstalled if you wish to return the Nook to factory defaults. However the stock recovery has fewer recovery features - so it is always safest to keep TWRP installed if you are tinkering with the device.
Rooting
Root Guide for the 2019 Glowlight Plus (using rootGLP)
1: Ensure you've enabled USB debugging tools from the developer options menu and saved a backup to a secure location
2: Connect the Nook to your computer. A popup will appear on your Nook asking to "turn on USB mode to safely move files..." click OK.
Note: This will cause your computer to download the appropriate drivers. After the drivers have been installed your Nook will show up in Windows Explorer and the Device Manager.3: Disconnect the Nook and go back to the developer settings menu (see steps 2.1) and select "disable mass storage".
Note: This will prevent USB mode from interfering as we run the ADB script.3: Download rootGLP.rar
Note: this is the same root script for the Glowlight 3, updated with the correct device name BGRV700. The original can be found in this XDA-thread. For a root guide for the Glowlight 3 using rootGLP, see this XDA-thread. The source is the wgznz forum (Chinese).4: Extract rootGLP
Note: It's best to run the script from a location like C:\rootGLP\ or D:\rootGLP\.5: Run the rootnook.cmd
Note: After the process is complete, you will see superSUfree appear on the screen. You will still need to install an alternate launcher.
Installing apps
Installing a launcher and apps (doesn't require root)
If you haven't installed ADB, you can use the copy of adb.exe in the rootGLP-3\bin\ folder by following the instructions below. After installing a launcher, you should consider installing a file browser (such as ES file explorer) and a better web browser, so that you can download and install apps without connecting to your computer.
1. Make sure you have enabled USB debugging tools from the developer options menu and saved a backup to a secure location
2. Navigate to the rootGLP-3\bin\ folder.
3. Place the launcher .apk inside the bin folder with adb.exe.
4. Click the address bar in Windows Explorer and type "cmd" without quotes and hit enter. A windows CMD terminal will open at the current folder address.
5. type adb install launchername.apk (replace with the name of your .apk file)
Note: kk launcher and text launcher are known to work.6. When you hit the U-shaped home button on your Nook, it will prompt you to select a launcher and ask if you would like to set it as the default. I recommend using "only once" at least until you can ensure you can always get back to the default launcher from whatever Android 4.4.2 compatible launcher you choose.
Installing KOreader and getting pageturn buttons working in KOreader (no root)
1. Download KOreader apk from https://koreader.rocks/
2. make sure your device is connected to adb and authorized with adb devices, if it t says "unauthorized", go to the developer menu (nook home > top right > all settings > page 2 > more > repeatedly tap logo) and tap "allow debugging".
3. install adb install koreader.apk. just hit tab to autocomplete the actual apk name.
4. Create a textfile "event_map.lua" in notepad and copy paste the following keymappings:
Code:
return {
[141] = "RPgBack",
[142] = "RPgFwd",
[140] = "RPgBack",
[139] = "RPgFwd",
}
5. use command adb push event_map.lua /sdcard/KOreader/settings/ to push the event map to the koreader settings.
6. If you had already installed and started KOreader before and just want to fix the keymapping, restart KOreader for the new settings to work (launcher > settings > apps > KOreader > force stop > home button > open KOreader > open book > test buttons > enjoy.
The stock recovery is not a big deal. It's in every update.zip
Just flash it with fastboot.
Why do you want it anyway when either TWRP or NeoNoogie is more powerful?
jun127 said:
It looks like it could be a useful resource, but it seems like a lot of steps and cautions are ommitted. Although I've installed TWRP, rooted, and installed the fastink kernel (among other mods) on my old NST, I would hesitate (especially as a new user) to install alternate firmware without a clear procedure to first backup and revert everything to factory defaults or recover if something goes wrong.
etc.
Click to expand...
Click to collapse
I am not the person to ask, but you are right that the first step is to be sure you can restore the device to stock. I'm one of those eccentrics who still loves and uses and continues to develop little improvements for the original NST/G, so all this fastboot stuff is pretty meaningless to me. I've flashed custom ROMs on Nook Tablets, but that's a totally different operation since back in the day Android was not locked up so tightly.
If you jut want a root guide (but it sounds like you want more than that): https://www.mobileread.com/forums/showpost.php?p=4202391&postcount=391
nmyshkin said:
I am not the person to ask, but you are right that the first step is to be sure you can restore the device to stock. I'm one of those eccentrics who still loves and uses and continues to develop little improvements for the original NST/G, so all this fastboot stuff is pretty meaningless to me. I've flashed custom ROMs on Nook Tablets, but that's a totally different operation since back in the day Android was not locked up so tightly.
If you jut want a root guide (but it sounds like you want more than that): https://www.mobileread.com/forums/showpost.php?p=4202391&postcount=391
Click to expand...
Click to collapse
I'd like to put together a simple guide, similar to what I wrote for the original NST about 10 years ago. I think the device needs a roadmap to outline what is currently possible in terms that are easy to follow. The device seems like it has a lot of potential, but it's just not very accessible at the moment.
I watched your video on running the CM on the NST, very interesting stuff and I'm glad to see some people are still keeping the device alive. I had used the original NST as a smartphone for a (short) while, even using it with Google phone and Whatsapp. It was surprisingly functional and, with the right optimizations, the battery could seemingly last forever with light use. Although it otherwise held up well, the rubber front panel and soft-touch back eventually degraded into a gooey mess. Removing the soft-touch coating on the back shell and replacing the rubber on the front with leather made it a more enjoyable reading experience for a while. Unfortunately, very poor app availability on Android 2.1 and the small, relatively low resolution display made it almost unusable for large format PDFs. Ultimately, the screen started failing and although it's still worth fixing, after 10 years it's overdue for an upgrade.
Renate said:
The stock recovery is not a big deal. It's in every update.zip
Just flash it with fastboot.
Why do you want it anyway when either TWRP or NeoNoogie is more powerful?
Click to expand...
Click to collapse
There's some peace of mind in knowing how to return things to exactly where you started. Even if unnecessary, there's always the possibility of some unforeseen issue and having a clear roadmap that you can follow to get back to the very beginning makes a difference in my mind.
Hi all,
I'm currently in front of a problem, and after a lot of tries and readings I decided to ask people.
As I'm a beginner, let me know if I'm not posting on the right place or if I'm saying stupidities.
My final goal is to install Home Assistant Operating System on my old Oneplus 5 phone.
This is the kind of stuff you usually do on a Raspberry, but I wanted to find a new usage of my phone.
Long story short, I've installed via Userland app Ubuntu 20.04 in order to create a VM on KVM as it seemed to be a good option to achieve my goal.
(I've also tried Termux but didn't seem to be as complete as Userland)
I ran a command to know if my CPU would support virtualization (kvm-ok) and I had this error :
Code:
INFO: /dev/kvm does not exist
HINT: sudo modprobe kvm
modprobe: FATAL: Module msr not found in directory /lib/modules/4.4.302-perf+
From what I understood, this issue comes from the fact that most phones do not have kvm enabled by constructors.
I wondered if the solution would be to modify the kernel ?
I found this but I'm not sure : https://github.com/android-linux-stable/op5
If someone has ever encountered this kind of problematic let me know.
If you have any other alternative, don't hesitate to share.
Some details about the device :
LineageOS 19-20221205-NIGHTLY-cheeseburger
custom BL TWRP
Magisk installed
For those who know Home Assistant, I succeeded to follow this tutorial, but it doesn't install a full version of it I wanted to try to install the OS.
Home Assistant Core on Android Tablet
You need install rust and cargo first: pip install rust pip install cargo run: rustc -vV | sed -n 's|host: ||p' it returns target system, something like: armv7-linux-androideabi copy it and set to cargo running: export CARGO_BUILD_TARGET=armv7-linux-androideabi then run: pip install...
community.home-assistant.io
Thanks !
cooldino said:
Hi all,
I'm currently in front of a problem, and after a lot of tries and readings I decided to ask people.
As I'm a beginner, let me know if I'm not posting on the right place or if I'm saying stupidities.
My final goal is to install Home Assistant Operating System on my old Oneplus 5 phone.
This is the kind of stuff you usually do on a Raspberry, but I wanted to find a new usage of my phone.
Long story short, I've installed via Userland app Ubuntu 20.04 in order to create a VM on KVM as it seemed to be a good option to achieve my goal.
(I've also tried Termux but didn't seem to be as complete as Userland)
I ran a command to know if my CPU would support virtualization (kvm-ok) and I had this error :
Code:
INFO: /dev/kvm does not exist
HINT: sudo modprobe kvm
modprobe: FATAL: Module msr not found in directory /lib/modules/4.4.302-perf+
From what I understood, this issue comes from the fact that most phones do not have kvm enabled by constructors.
I wondered if the solution would be to modify the kernel ?
I found this but I'm not sure : https://github.com/android-linux-stable/op5
If someone has ever encountered this kind of problematic let me know.
If you have any other alternative, don't hesitate to share.
Some details about the device :
LineageOS 19-20221205-NIGHTLY-cheeseburger
custom BL TWRP
Magisk installed
For those who know Home Assistant, I succeeded to follow this tutorial, but it doesn't install a full version of it I wanted to try to install the OS.
Home Assistant Core on Android Tablet
You need install rust and cargo first: pip install rust pip install cargo run: rustc -vV | sed -n 's|host: ||p' it returns target system, something like: armv7-linux-androideabi copy it and set to cargo running: export CARGO_BUILD_TARGET=armv7-linux-androideabi then run: pip install...
community.home-assistant.io
Thanks !
Click to expand...
Click to collapse
To install Home Assistant Operating System (HASSIO) on your Oneplus 5 phone, you will need to follow these steps:
First, make sure that your phone is rooted. Rooting your phone will allow you to install custom operating systems on it. There are various tutorials and tools available online that can help you root your Oneplus 5 phone.
Once your phone is rooted, you will need to install a custom recovery such as TWRP (TeamWin Recovery Project). This will allow you to boot into a custom recovery environment and install HASSIO on your phone.
Download the HASSIO image file for your phone from the Home Assistant website or from a third-party source.
Hamzagujjar said:
To install Home Assistant Operating System (HASSIO) on your Oneplus 5 phone, you will need to follow these steps:
First, make sure that your phone is rooted. Rooting your phone will allow you to install custom operating systems on it. There are various tutorials and tools available online that can help you root your Oneplus 5 phone.
Once your phone is rooted, you will need to install a custom recovery such as TWRP (TeamWin Recovery Project). This will allow you to boot into a custom recovery environment and install HASSIO on your phone.
Download the HASSIO image file for your phone from the Home Assistant website or from a third-party source.
Click to expand...
Click to collapse
My phone is rooted and I've already installed TWRP.
I think there is no HASSIO image file for phones in general.
Could you detail this part ?
Thanks