Hey y'all,
Picked up a SM-N935L a few weeks ago. Last week, for no reason I can think of, the touchscreen started causing problems.
As of now, a 1 inch swath of the screen on left side doesn't respond to touches unless they are long touches. This is annoying on the homescreen, but IMPOSSIBLE when trying to type on the keyboard as the number key, shift, A, Q, and 1 key barely ever respond to touch.
AT first it was intermittent. Now it's permanent.
The S-Pen works perfectly, even in the affected area of the screen.
I tried flashing the original firmware the phone came with before the OTA, no dice.
Long story short, the phone is now back in it's box and I am back to my old n9005 Note 3.
Has anyone else run into this?
Before someone says that maybe the screen connector is loose on the motherboard, I cracked the phone open (heatgun, etc) and checked that. Not the issue.
I even tried the secret code *#6233*# which allows you to "update" the touchscreen firmware. No difference.
Any thoughts?
you didn't mention the software version you're using.... did you update to the latest OTA for the L version of the Note FE? Google Translation change log
Build Number: N935LKLU3AQG6 Android version: Nougat (Android 7.0)Release date: 2017-08-04
ㆍ Improve the phenomenon that the tone of the song is reduced or silenced in a specific environment
ㆍ Correct the phenomenon that the photo position information is displayed when the camera is shot
ㆍ Intermittently break when touching the upper / lower touch
Build Number: N935KKKU3AQFEAndroid version: Nougat (Android 7.0)Release date: 2017-07-06
ㆍ Apply stabilization code related to camera operation
My bad for.not being specific. Yes I am on QG6. I went back to QFE hoping for a change. No difference.
ClrDaLane said:
Hey y'all,
Picked up a SM-N935L a few weeks ago. Last week, for no reason I can think of, the touchscreen started causing problems.
As of now, a 1 inch swath of the screen on left side doesn't respond to touches unless they are long touches. This is annoying on the homescreen, but IMPOSSIBLE when trying to type on the keyboard as the number key, shift, A, Q, and 1 key barely ever respond to touch.
AT first it was intermittent. Now it's permanent.
The S-Pen works perfectly, even in the affected area of the screen.
I tried flashing the original firmware the phone came with before the OTA, no dice.
Long story short, the phone is now back in it's box and I am back to my old n9005 Note 3.
Has anyone else run into this?
Before someone says that maybe the screen connector is loose on the motherboard, I cracked the phone open (heatgun, etc) and checked that. Not the issue.
I even tried the secret code *#6233*# which allows you to "update" the touchscreen firmware. No difference.
Any thoughts?
Click to expand...
Click to collapse
Try *#2663#, which will update the TS firmware. Used this recently to correct a touch screen reversal (which was a weird experience at first).
zamzenos said:
Try *#2663#, which will update the TS firmware. Used this recently to correct a touch screen reversal (which was a weird experience at first).
Click to expand...
Click to collapse
Sorry. That's the code I used, not 2633. It didn't help at all.
Have you installed any apps that control screen brightness, remove the brightness slider from quick settings? If yes, uninstall and see if that fixes the issue.
Very late to the party but I'm having the same issue. Tried everything and no luck. The left side of screen not responding unless I use the pen. Stock OS no extra apps installed. Gutted.
I also have this problem..after one month use..right side screen doesnt respon..
Im runing on ARA1 firmware
hi pro, did you fix it, i have same issue
I had the right edge screen problem too. You can use *#0*# to test. Select touch to start the test.
Press 'volume up' button once done.
My problem on the right side and only not responsive to touch only. S pen works fine though.
I went to samsung and they said they had replaced the screen. And it works ! So guys, maybe it's really a hardware problem with the display screen.
Now after 2 month, the problem had resurfaced
I really like this phone and my note 4 previously was great and not having any hard problem.
I'm going to send this again to samsung for repair since it's still under warranty. Hope the problem will diasppear and not repeating again once we warranty expires.
Hello, i am having the same problem. It started about a week ago when the left side of my phone became unresponsive to touch. I have to long press the left side of the screen to register my touch. I tried the "Touch" test at *#0*# and the left side cant be touched. Now the lower and right side of the screen became unresponsive too. Anyone knows how to fix? Using Android 8.0.0 on this Samsung Galaxy note FE
exactly happen to me too...
went to samsung center and replace the screen, under warranty
Same Here
Hi
the same issue started happening to my Note FE yesterday.
have you found a way to fix it? or have you returned the product?
BAD NEWS everyone
Hey y'all,
So I have bad news for you.
The problem is hardware not software. I ended up giving my dad the phone when he went on a business trip to Hong Kong. He's got a guy there that owes me a favor or two so he got the screen replaced. That fixed it immediately.
Sorry for not updating you guys. I ended up just picking up a brand new Note8 back in Nov when I had enough of the touchscreen thing. When my dad finally brought me the FE back with the new screen it worked perfectly.
No software changes at all. Just replaced the screen.
Hi !I am having the same problem here with the right side of the screen.
First it started when the right side started to be less sensitive but then after a while it suddenly stopped working for the touch. The S Pen works ok.
Its really terrible to use it like this. At least if there was an option to squeeze the screen. Where did you guys bought the phone? I am in Europe but i think the company imported it from Saudi Arabia. Dont know if its a regional issue but i am courious. I tried clearing the cache and updating the touch but no difference. Haven`t tried factory reset yet....
Radium82 said:
Hi !I am having the same problem here with the right side of the screen.
First it started when the right side started to be less sensitive but then after a while it suddenly stopped working for the touch. The S Pen works ok.
Its really terrible to use it like this. At least if there was an option to squeeze the screen. Where did you guys bought the phone? I am in Europe but i think the company imported it from Saudi Arabia. Dont know if its a regional issue but i am courious. I tried clearing the cache and updating the touch but no difference. Haven`t tried factory reset yet....
Click to expand...
Click to collapse
hi what is your update about your screen problem ? and for how long did you use your note fe before this problem appeared? maybe you dropped it or something?
Hi. I'm having the same issue. I'm in Saudi so maybe it's a region thing?
Right side not working with touch but only for the s-pen. Also now the s-pen or finger has wrong touches in the screen.
nesoor1230 said:
hi what is your update about your screen problem ? and for how long did you use your note fe before this problem appeared? maybe you dropped it or something?
Click to expand...
Click to collapse
I have been using it for about 3 months before it first started to lose its sensitivity and then to not function at all on a 1 cm wide area on the right side. I havent dropped it for this to be an issue and since i already seen other people complaining its definately a manufacturing issue. I have sent it to the service and hope to have an answer and i will update here about it.
---------- Post added at 06:47 PM ---------- Previous post was at 06:45 PM ----------
ahddie said:
Hi. I'm having the same issue. I'm in Saudi so maybe it's a region thing?
Right side not working with touch but only for the s-pen. Also now the s-pen or finger has wrong touches in the screen.
Click to expand...
Click to collapse
My phone is also imported from Saudi Arabia. It could be a problem with this region, i don`t know.
---------- Post added at 06:48 PM ---------- Previous post was at 06:47 PM ----------
ClrDaLane said:
Hey y'all,
So I have bad news for you.
The problem is hardware not software. I ended up giving my dad the phone when he went on a business trip to Hong Kong. He's got a guy there that owes me a favor or two so he got the screen replaced. That fixed it immediately.
Sorry for not updating you guys. I ended up just picking up a brand new Note8 back in Nov when I had enough of the touchscreen thing. When my dad finally brought me the FE back with the new screen it worked perfectly.
No software changes at all. Just replaced the screen.
Click to expand...
Click to collapse
Hello, do you know if your phone was imported from Saudi Arabia? It might be a problem with the phones for this market.
Thanks all for your reply. Really its very scary, just brought a new one from Saudi Arabia, where made in Vietnam. Sometimes I feel some lag with back button . But I dont think its common defect, I heard about same problem in Note 8. Those screen curves brought troubles to all of us ,
I installed tempered glass screen protector but it didn't cover the whole screen , anyway I preferred it rather than the normal elastic one.
Exactly the same issue on my FE
Nope. It happened to me as well just this morning. It is exactly as you've described. I did a factory reset but the issue still persists.
Related
Hear that S/N before HT63XXXXXX have screen alignment problems and was wondering if upgrading it to a newer ROM (like the latest TyTN) ROM would solve this problem?
Can't really seem to draw a conclusive result from the threads posted but would appreciate those who faces/are still facing this problem, could provide their thoughts on this.
Hi, I've got a V1605 with a 628 serial number. Changing to the update from the shipped Vodafone rom and 48 hours later I have not had one single screen alignment issue. My scroll wheel stopped working earlier but a soft reset solved that issue.
Phil
low405 said:
Hi, I've got a V1605 with a 628 serial number. Changing to the update from the shipped Vodafone rom and 48 hours later I have not had one single screen alignment issue. My scroll wheel stopped working earlier but a soft reset solved that issue.
Phil
Click to expand...
Click to collapse
Hi there and thanks for your reply. Did you happen to have the screen alignment problem before the update?
vapor said:
Hi there and thanks for your reply. Did you happen to have the screen alignment problem before the update?
Click to expand...
Click to collapse
Very mildly on this on (my third). Mostly did it when using opera. A tap and hold could be anywhere on the screen. It was also bad whilst charging. Now it seems perfect but I will feedback more after a couple of days more use as it does seem to be something that builds up after hard reset.
thanks for you input. i look forward to your continued help on this matter
Yep, I flashed last night and no screen alignment issues at all today. I was able to reproduce the screen alignment problem before the flash too.
waveydavey ....
Paul here ..
I didn't realise you had any of these problems with your device ....
When did the alignment problems start to affect your device ?
Also ... when I asked you about BT stereo ... I thought you said you were happy ... but following the ROM upgrade you suggested it was 'still' not good.
Are you experiencing problems that you didn't have when you first received the device ?
My biggest issue is the loose stylus .... still being held in by the 'spring' but very little friction anymore ... also sometimes doesn't want to come out unless you rotate in the silo first.
Cheers
Paul.
waveydavey,
which rom version did you update to and do you have a link for it? Did you have to reinstall all your apps?
Does anyone know if HTC has confirmed this problem exists?
Have they determined if its hardware or a software glitch
i just got a Dopod CT9000 with SN HT625XXXXX with the English ROM and so far I have not encountered any screen alignment problem. Some users say the alignment problem is a result that builds up over time so I shall wait and see what happens.
It seems like on my unit the update has fixed it but at the same time hasn't.
Yesterday it lost alignment on the right hand side of the screen. Left was fine but right was 1cm to the left of where it should've been. I realigne the screen and ten minutes later the rigth hand side was 1cm to the right of where it should've been. It might have just got a bit confused but I'll continue to keep an eye on it and report back.
First time since the rom became available as I flashed it as soon as it appeared here.
Phil
low405 said:
It seems like on my unit the update has fixed it but at the same time hasn't.
Yesterday it lost alignment on the right hand side of the screen. Left was fine but right was 1cm to the left of where it should've been. I realigne the screen and ten minutes later the rigth hand side was 1cm to the right of where it should've been. It might have just got a bit confused but I'll continue to keep an eye on it and report back.
First time since the rom became available as I flashed it as soon as it appeared here.
Phil
Click to expand...
Click to collapse
Phil,
Had this happened after making a lot of calls or anything else that would heat the device up? The hardware aspect of the issue is allegedly that a heating issue causes the screen to become misaligned.
bydandie said:
Phil,
Had this happened after making a lot of calls or anything else that would heat the device up? The hardware aspect of the issue is allegedly that a heating issue causes the screen to become misaligned.
Click to expand...
Click to collapse
Not really, It was in my pocket while I was shopping when I recieved an email. Checked it and noticed the alignment. Realigned the screen. 10 minutes later and I got another email and it had gone back to the previous alignment.
Heat hasn't affected it in the last few days. An hour and a half on the train surfing using opera full screen every morning and I didn't have any issues even though I could feel it getting hot.
No added software or different use after the initial set up.
I'll keep an eye on it. It could've been "just one of those things" and the fact that it went back to where it had been would back that up. I have had a few problems with the scroll wheel not functioning since the upgrade though. Maybe 2 or 3 times it has just refused to work until a soft reset.
Phil
well so far i have yet ot encounter the problem. everything seems to be ok for me but i have yet to push the device like making long calls or sirfing on it for a long time. will keep on testing and keep you updated.
pgamble said:
waveydavey ....
Paul here ..
I didn't realise you had any of these problems with your device ....
When did the alignment problems start to affect your device ?
Also ... when I asked you about BT stereo ... I thought you said you were happy ... but following the ROM upgrade you suggested it was 'still' not good.
Are you experiencing problems that you didn't have when you first received the device ?
My biggest issue is the loose stylus .... still being held in by the 'spring' but very little friction anymore ... also sometimes doesn't want to come out unless you rotate in the silo first.
Cheers
Paul.
Click to expand...
Click to collapse
Hey Paul, sorry only just checked this thread today. Not got too much time today but, I think I've answered both these on 4WM in the
Tutorial: Replace Hermes headset connector with 3.5mm socket
and
Screen alignment issues? Calling all Hermes owners!!!
If not give us a prompt .
bydandie said:
low405 said:
It seems like on my unit the update has fixed it but at the same time hasn't.
Yesterday it lost alignment on the right hand side of the screen. Left was fine but right was 1cm to the left of where it should've been. I realigne the screen and ten minutes later the rigth hand side was 1cm to the right of where it should've been. It might have just got a bit confused but I'll continue to keep an eye on it and report back.
First time since the rom became available as I flashed it as soon as it appeared here.
Phil
Click to expand...
Click to collapse
Phil,
Had this happened after making a lot of calls or anything else that would heat the device up? The hardware aspect of the issue is allegedly that a heating issue causes the screen to become misaligned.
Click to expand...
Click to collapse
how hot was your device?
boxer82003,
Not warm at all. It has been fine all day today!
Phil
has HTCconfirmed this as a problem
wwaveydave said:
Yep, I flashed last night and no screen alignment issues at all today. I was able to reproduce the screen alignment problem before the flash too.
Click to expand...
Click to collapse
How were you able to reproduce the screen alignment problem before you flashed your device.
I've called the HTC support in Italy and they told me to send the TyTN back for a swap.
Ciao.
After 4 months of flawless work, the lower part of the screen (a strip several millimeters from the edge) suddenly stopped responding properly!
E.g., all buttons in this area (including launcher/phone/+ on home screen) either don't work at all, or sometimes activate after a while when strongly pressed with the thumb (orientation doesn't matter).
Just two hours before they responded fine to the index finger.
Also, I've noticed that when I "multi-touch" the lower line in a file browser with two fingers, it works nice! Buttons are too small for that, however
I first tried to restore backup, but it didn't help, of course.
Has anybody had the same problem?? I guess it's a warranty case ...
I would agree, it's probably a hardware problem that you'll have to bring your phone in for service to get fixed.
I'm having that same problem my self, but just now and then. What helped with me is that I press the upper left corner of the phone with my other hand and then the lower part works fine, so i think i should get a new digitizer or its just loose connector.
im having the same problem , i have put up with it for the past few weeks and its driving me nuts now. today i did a factory reset which made no difference , i called htc who didnt sound a bit suprised by my phone call it gets picked up tomorrow morning to go for repair so the question is ... is this a common fault? and how the hell am i gonna cope without my hero in my pocket ?
Yeah happened to mine last week, a few have had the same issue where it's just the launcher bit not responding. Although the good news is that I'm getting it back tomorrow though so it's good times!
I had the same problem with my touchscreen (after a month or so!)
Mine got picked up thursday by HTC and I just checked the tracking site and they just recieved it.
I wonder how long it's going to take
Visited their service center last week.
They've immediately replaced my screen with a new one without any ado. Now everything works as before!
BUT a friend of mine who bought his Hero in January is having similar problems now...
It is a common problem according to HTC.
Mine was repaired in just 10 days.
Same problem here, did htc said anything about this problem? is it a common fault?
thank you
I said it in the post above yours.
ah yes, right, thank you
mach2005 said:
It is a common problem according to HTC.
Click to expand...
Click to collapse
If they acknowledge it officially, couldn't you provide a link please?
i gave mine last week to repair, they returned to me unfixed. on the paper stated that they only updated the software, what a dumb this htc guys. need to go back and tell them again the same story. im wasting my time only for this. wtf
I recently had this problem. The 3 buttons at the bottom of the screen wouldn't respond, took it into T-Mobile who said I'd have it back within about 7 to 10 days... 3 weeks later I got a text saying I could collect my phone...
On the paper sheet it says they've replaced the lens.. Which I can see they have as before I had a miniscule hairline scratch near the top.
They also mention a software update (1.0.0.A6288)
Either way it works nicely now.
I've recently experienced the same issue - the lower part of the screen, the one where the LauncherPro icons usually are stopped responding to touch. If I press really hard it works sometimes, but it's pretty annoying. I didn't sit on the phone or drop it recently, it just stopped working all of a sudden.
Is there anything I can do, as the phone is out of warranty ?
HTC South Africa gave me a new hero after I took mine in for the 3rd time. Hardware problem. Very happy with their service.
i have this exact same problem, is the only solution to send to htc? >_> Cuz my warranty's out already unfortunately... i flashed my hero to CyanogenMod 7 and it seems to have helped, but still not completely responsive... I also have a problem where at times i completely lose control of my touch screen where the spots i touch seem to respond to opposite sides of the screen... anyone else?
Remove battery, Remove sim card. put a dryer on the htc logo for about 40 mins. put the phone under a heavy object. Let it dry for about 15 mins and your fixed.
^ wtf do u mean?... are u just being a gimp...
VillainRocks said:
Remove battery, Remove sim card. put a dryer on the htc logo for about 40 mins. put the phone under a heavy object. Let it dry for about 15 mins and your fixed.
Click to expand...
Click to collapse
i am having the same problem and i badly need to solve it please could u tell me that what do you exactly mean by put a dryer on the htc logo
thanks
The top part of my phone does not respond to touch anymore... it is impossible to bring down the notification bar... and once in a while the whole screen goes unresponsive.. tried factory reset but still the same problem..
am having the same problem since 2 days back
after reading some of the posts i found that the Digitizer For HTC G6 Legend A6363 should be replaced with new one i ordered mine from ebay
ebay.com/sch/i.html?_from=R40&_trksid=p5039.m570.l1313&_nkw=Digitizer+For+HTC+G6+Legend+A6363&_sacat=See-All-Categories
waiting for the item to be delivered
I've also got a touchscreen issue: the area of the notification power widgets is unresponsive... the rest of the screen works fine, but I don't know for how long :/
nnssxx said:
I've also got a touchscreen issue: the area of the notification power widgets is unresponsive... the rest of the screen works fine, but I don't know for how long :/
Click to expand...
Click to collapse
Do you have widgetlocker, by any chance ?
Or a lockscreen replacement which disable the notification bar during the "slide to unlock" state ?
I didn't know there was such thing as widgetlocker. I use CM7 latest nightly, never seen that thing.
I also facing this problem from last 2 weeks and i also think this is digitizer problem. If anyone else found the solution else changing the digitizer, then please post.
This is beautiful phone but htc added a poor quality things in it, due to which many users facing such problems.
Nah.. I dont think its because of widget locker.. its the digitizer..
well that's a shame, gotta buy a new digitizer on ebay after just over 1 year of use...
I know.. this sucks... Im planning to upgrade though.. Any of u guys have any suggestion?
Depends on your carrier if you want suggestions for an upgrade.
...but that would drive the post off-topic.
Sent from my HTC Legend using XDA App
I have the same problem. my screen doesnt work anymore because some water got in from the grill above the screen :S
should I try to take apart and dry off or shall I buy a new digitizer directly?
I think it may be a good idea to try disconnecting your digitizer and reconnect it as it just might be helping. I did it on my girlfriends legend and it has been working perfectly ever since. Maybe a good idea to at least try that before buying a new one. So i guess it could be in the connector to? At least this worked for me.
My touch screen dosent work at times. but after rebooting the phone the problem becomes solved. But the problem comes again after a week or so. Any suggestions guys??
Earayil said:
My touch screen dosent work at times. but after rebooting the phone the problem becomes solved. But the problem comes again after a week or so. Any suggestions guys??
Click to expand...
Click to collapse
I also have this problem, but if I wait a couple of minutes the touchscreen
becomes responsive again. Half of the screen works when it's unresponsive (right half of the notification bar and down). It's quite annoying but I cannot afford a new phone at the moment.
I'm also wondering if this might be temperature related, this problem reoccurred very often during the summer but stopped during the winter. But now (spring) it's back again.
My problem got worse and the phone became totally unresponsive, changed it, got a new phone.
Tanayar said:
I also have this problem, but if I wait a couple of minutes the touchscreen
becomes responsive again. Half of the screen works when it's unresponsive (right half of the notification bar and down). It's quite annoying but I cannot afford a new phone at the moment.
I'm also wondering if this might be temperature related, this problem reoccurred very often during the summer but stopped during the winter. But now (spring) it's back again.
Click to expand...
Click to collapse
exact same problem here, mine works when it feels like working, totally random, I simply can't understand why, I doubt it's the temperature... I think its in the device theres something wrong, I smack it numerous time and it works right after a big smack on the screen, or rub your whole hands on the screen, also, the angle you are holding the phone affects this problem, if none of these work, a phone restart always makes it work at the beginning. Oh boy did my phone took and taking much beating... oh well, I wish I could permanatly fixed the problem here, as I was thinking of handing the phone to my brother when I upgrade, I'm using CM 6.1.
I still recommend the same thing that i posted earlier here, her screen still works perfect.
I had the same problem few months ago. The problem is with the touch digitizer. I bought a digitizer on ebay and replaced it myself. After that my phone has been working fine. Its not that hard to replace it if you have a small knowledge about hardware.
I use to get that unresponsive screen issue only in the summertime, plus it gets worse if I add humidity (read: sweat). I just need to give it some time then to dry off/ cool down outside my pocket, and it's all fine again.
Hello,
Not sure if I can ask this as I am a brand new user. I hope you can help.
Friend brought me their Galaxy S4 i337 4.4.2 stock firmware. It acts as if the very top left (or around the area) is permanently pressed not allowing for any other touch function unless I touch that area "taking over" the ghost touch. The moment I let go, it is brought back to that area of the digitizer. Sometimes it works for half a second or 2 but goes right back to the problem area soon after. I have soft reset, hard reset with no avail. I have also connected a new LCD assembly which works perfect. I am assuming after this that the digitizer is the problem though I am interested what would cause such an issue to only part of the digitizer. She did mention she is prone for dropping the phone though it had been about 24 hours after the latest drop that the digitizer started acting up and has not let up since.
Any ideas ?
Thank you and again I apologize if I am not allowed to post this here.
Tristan
My fingerprint scanner has stopped working, after I upgraded to Android 7 (Nougat).
I took it into my Samsung store who said it was a hardware issue, it failed the self diagnostic test.
However they refused to fix the issue under warranty because the screen is cracked.
The screen has been cracked for over 5 months now, so I hardly see how they are related.
Can anyone way in on this?
jjgriffsta said:
My fingerprint scanner has stopped working, after I upgraded to Android 7 (Nougat).
I took it into my Samsung store who said it was a hardware issue, it failed the self diagnostic test.
However they refused to fix the issue under warranty because the screen is cracked.
The screen has been cracked for over 5 months now, so I hardly see how they are related.
Can anyone way in on this?
Click to expand...
Click to collapse
Well if the screen is cracked, and your phone is still under warranty, then surely they should be fixing that too ? Samsung sound pretty useless to me, and use every excuse under the sun for not fixing things, try boot to recovery and factory reset, this can sometimes fix faults after an update.
EDIT: after updating mine to androind N, the fingerprint reader is working fine, infact so far ive got no problems here at all.
Yep a long as it is a UK model and under one year old Samsung should change the screen and fix the touch sensitive button. As long as you don't have a great big dent in the case that caused the cracked screen...... I just ordered new back cover for mine as it's a dual SIM and Samsung won't repair it under warranty. They quoted £65 to change the back cover and I purchased it on eBay for £20.
I will heat up the back cover and change it myself tomorrow.
Sent from my SM-G935F using Tapatalk
jjgriffsta said:
My fingerprint scanner has stopped working, after I upgraded to Android 7 (Nougat).
I took it into my Samsung store who said it was a hardware issue, it failed the self diagnostic test.
However they refused to fix the issue under warranty because the screen is cracked.
The screen has been cracked for over 5 months now, so I hardly see how they are related.
Can anyone way in on this?
Click to expand...
Click to collapse
Try to go back to MM.
Download latest MM version from sammobile.com and flash it with Odin
Then you will know if it's SW- or HW problem
angusc said:
Yep a long as it is a UK model and under one year old Samsung should change the screen and fix the touch sensitive button. As long as you don't have a great big dent in the case that caused the cracked screen...... I just ordered new back cover for mine as it's a dual SIM and Samsung won't repair it under warranty. They quoted £65 to change the back cover and I purchased it on eBay for £20.
I will heat up the back cover and change it myself tomorrow.
Sent from my SM-G935F using Tapatalk
Click to expand...
Click to collapse
Let them do it so you keep your device's water resistance.
s7 edge fingerprint sensor error
Wanted help regarding my s7 edge fingerprint sensor. It responds just fine sometimes but most of the time it gives an error. I tried the solution of clearing cache , pressing power and volume down button together to soft reset it. But nothing worked. The funny part is that it will respond for a few while after rebooting ( restarting ) it but when it gibes the error it stops completely until restarted again. Did not drop it. Didn't place it in water. The problem did start after updating from marshmallow to nuogat and even after getting two security patch updates. Don't know what to do. Can anyone plz guide me how to use *#0*# code to check fingerprint sensor because when i check it it sometimes give that intializing failed. Sometimes if i don't put my finger on the sensor it says it passed and when i place my finger it only shows first box passed while the rest of the boxes fail. I searched everywhere on internet for but in the end came back to xda and decided to ask u guys. As i did got alot of help from u guys on my s2 and note 4. I hope that someone might try to help.
I don't know the answer, but I can confirm a similar issue with my S7 since upgrading to nougat. Also I seen to get a few apps force closing. My device is stock and not rooted. I got so fed up with the finger scanner not responding I switched back to only a pin code for a week. Now I switched back to finger print and only set up one finger print memory........now for a week it send to be working, but still getting force closes of the play store app.
Sent from my SM-G935F using Tapatalk
My galaxy s7 edge sensor can't work requiring device restart. I have restarted many times and still it doesn't work. I hope that someone might help me to fix it
Firehun said:
My galaxy s7 edge sensor can't work requiring device restart. I have restarted many times and still it doesn't work. I hope that someone might help me to fix it
Click to expand...
Click to collapse
Try to reinstall the rom stock. If the problem persists, then it is a hardware problem. Your sensor went to the bag.