i installed the Ezinput from http://forum.xda-developers.com/showthread.php?t=536215 for wvga... i installed it, then it said a reset is required to finish intallation. after the reset, it went to the touch diamond 2 boot up screen, after that was over, then screen displayed nothing. its black, and usb does not respond when i connect it to the computer. any ideas? i already tried the reset using teh red button. took out the memory card, where i install the .cab, still doesnt work. any help would be greatly appreciated.
If it's totally unresponsive from boot, hard reset it. Hold Volume Down and press the "red button" to reset it. It'll go back to factory settings.
same problem here, help needed!!
i tried to restore it to the factory setting using volume down and red button but when the phone flashes it shows me this three color screen with the message "serial" on the bottom side of the screen, any ideas on what should i do???
thanks in advance...
To perform a Diamond 2 hard reset
1. With the device turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then briefly press the POWER button.
2. Continue pressing the VOLUME UP and VOLUME DOWN buttons until you see a message on the screen.
alwaysrun said:
i tried to restore it to the factory setting using volume down and red button but when the phone flashes it shows me this three color screen with the message "serial" on the bottom side of the screen, any ideas on what should i do???
thanks in advance...
Click to expand...
Click to collapse
What you did is boot in "bootloader mode"; in that mode you can try to flash again the original ROM.
thanks
thanks a lot guys, your help is well appreciated, i finally managed to flash the phone bios and now trying to install the original rom, thank you again
hello,
my phone didn't work when I turn it on it stuck on the "starting screen" and I can get into recovery (the screen that used only by the volume buttom and home key)
I dont know what can I do for it works.
please help me..
thank you very much !
XperiaX8D said:
hello,
my phone didn't work when I turn it on it stuck on the "starting screen" and I can get into recovery (the screen that used only by the volume buttom and home key)
I dont know what can I do for it works.
please help me..
thank you very much !
Click to expand...
Click to collapse
If you can go to recovery then restore previous backed up rom or Flash a new rom
Hi guys, (LG G2, Rooted, had twrp but now its vanished?!)
I managed to get my LG G2 into a bootloop. I was replacing bootanimations and rebooting and testing them out. I finally tried this 1080p boot animation that looked sweet. Once the device rebooted it would show half the boot animation and then reboot. I had twrp installed but now every time i try to access it it just ignores the hotkeys as if it doesn't exist anymore. I can only get into download mode if a usb is plugged in.
All i need to do is flash TWRP again so i can flash the stock bootanimation back. I do not want to do a fresh install as I have many important files (i know i should have backed them up). I have tried to access my phone via adb using windows commandline tool whilst in download mode. however, adb doesn't find my device (I was going to attempt to push the stock animation back).
Please help me guys i need my phone to be working by monday as i have work! thanks in advance
SPBoss said:
Hi guys, (LG G2, Rooted, had twrp but now its vanished?!)
I managed to get my LG G2 into a bootloop. I was replacing bootanimations and rebooting and testing them out. I finally tried this 1080p boot animation that looked sweet. Once the device rebooted it would show half the boot animation and then reboot. I had twrp installed but now every time i try to access it it just ignores the hotkeys as if it doesn't exist anymore. I can only get into download mode if a usb is plugged in.
All i need to do is flash TWRP again so i can flash the stock bootanimation back. I do not want to do a fresh install as I have many important files (i know i should have backed them up). I have tried to access my phone via adb using windows commandline tool whilst in download mode. however, adb doesn't find my device (I was going to attempt to push the stock animation back).
Please help me guys i need my phone to be working by monday as i have work! thanks in advance
Click to expand...
Click to collapse
1. If you connect your phone to PC, what happens?
2. I also had trouble accessing TWRP, so I did the "Factory reset" button combo (Don't remember what it was) and when I slided to confirm, twrp booted. From there I think you have adb and can fix everything.
To get to TWRP, hold the power button until the phone turns completely off, then turn on the phone while holding the power and volume down buttons, then when the LG logo pops up, let go and re-press those buttons. When prompted for a factory reset, press the power button. Works every time for me.
Alone i used lg flashtoolnow,its ok. I didnt click factory reset i assumed it would delete everything? With lgflash i have restored system and everything is how i left it.
Sent from my LG-D802 using Tapatalk
alone-together said:
To get to TWRP, hold the power button until the phone turns completely off, then turn on the phone while holding the power and volume down buttons, then when the LG logo pops up, let go and re-press those buttons. When prompted for a factory reset, press the power button. Works every time for me.
Click to expand...
Click to collapse
worked like a charm, many thanks!
alone-together said:
To get to TWRP, hold the power button until the phone turns completely off, then turn on the phone while holding the power and volume down buttons, then when the LG logo pops up, let go and re-press those buttons. When prompted for a factory reset, press the power button. Works every time for me.
Click to expand...
Click to collapse
i cannot enter the download mode and the recov mode. I pressed it as your instruction said, but nothing happened.. what should i do ?
All the application force close, so i cannot enter the OS either..
xzork said:
i cannot enter the download mode and the recov mode. I pressed it as your instruction said, but nothing happened.. what should i do ?
All the application force close, so i cannot enter the OS either..
Click to expand...
Click to collapse
First off, you'll need to make sure your phone isn't plugged in or it won't work - I'm afraid if you can't enter recovery you'll have to go back to stock. http://forum.xda-developers.com/showthread.php?t=2432476
Sucess
alone-together said:
To get to TWRP, hold the power button until the phone turns completely off, then turn on the phone while holding the power and volume down buttons, then when the LG logo pops up, let go and re-press those buttons. When prompted for a factory reset, press the power button. Works every time for me.
Click to expand...
Click to collapse
Thank you, saved me day.
dear sir good evening sir plz plz help me my LG G2 is not working. still only black screen and show lg logo sir plz help me:crying:
PUNNU NAGI said:
dear sir good evening sir plz plz help me my LG G2 is not working. still only black screen and show lg logo sir plz help me:crying:
Click to expand...
Click to collapse
Try to flash the Kitkat baseband or if you are fully stock then i suggest you to flash the KDZ to go back to full stock(http://forum.xda-developers.com/showthread.php?t=2432476)
If you still have important data like pictures or what then do normal flash. Use the Android version you also had as stock and use that as KDZ. If you are not stock then can you reach TWRP?
and what did you do before that causes the black screen?
Stuck with the LG logo. Nothing happens in download mode
Hi All, not sure if this has been answered prior. This is what happen, I wanted to flash SOKP so I backup my phone and saved to PC using Titanium. I have TWRP installed.
Boot Into Recovery Mode and Wipe Data,System,Cache,Dalvik
I restart so I can flash the SOKP Rom and all I see on my phone is the LG logo. I try to restart using the Power and Up button, but it just sits in the download mode saying "Firmware Update" with no movement or action.
The phone is unable to turn off now. This is my first go at Flashing a Rom. Any help or suggestion would be greatly appreciated. Thanks in advance
my lg g2 is stuck on lg logo, and when i can enter download mode, and flash kdz my computer just dont detect my phone.
please help me :crying:
jungsora said:
my lg g2 is stuck on lg logo, and when i can enter download mode, and flash kdz my computer just dont detect my phone.
please help me :crying:
Click to expand...
Click to collapse
same here .... plz any solution?
justme!! said:
same here .... plz any solution?
Click to expand...
Click to collapse
Someone help, same issue.
sam_p15 said:
Someone help, same issue.
Click to expand...
Click to collapse
Someone help
Hey, I have the nearly same problem with my G2 running CM12 also installed recovery
But I can't reboot in recovery neither with the factory reset buttons, nor manually with SDK Manager, because the device is not found.
So I can just reboot and it shows the CM boot image, or get in the download mode.:crying:
Any suggestions?:fingers-crossed:
sam_p15 said:
Someone help, same issue.
Click to expand...
Click to collapse
I was in same stuation before 2 months send to warranty.
If rooted you can use adb shell with su and push partitions with "dd" while staring (stuck in lg logo)
Help!!
I have boot loop, only download mode accessible, device not found on adb. When I try LG FlashTool, instead of using the KDZ file I provide, it starts downloading some other firmware at times, and at times it says your software is up to date. What do I do? :|
How do i fix TWRP Bootloop on my HTC explorer a310e... ?
Dear,
How do i fix TWRP Bootloop on my HTC explorer a310e... ?
I hav custom cm11 Kitkat ROM installed on it...
but after I installed the rom, and again tried to reboot
into TWRP recovery, it is just stuck on the blue color
TEAMWIN screen... Please help how to fix it...!
USE method with .tot is working for me
Hi,
I'm having issue with a GT-I9505 S4 phone after droped it in the water, key combinaison to turn the phone up are altered, if i only push "power" button, the phone boot in recovery mode, if i push "volume down + home + power" the phone boot android in normal mode.
I've tryed to re-install samsung stock rom, the problem persist, i've tryed to install cyanogenmod 12 and problem still here too.
It's seem the water have corrupted a firmware (maybe qualcomm's firmware?) so i don't find which one !
When powering the phone with "volume down + home + power", all work just fine !
I've checked if some buttons are stuck, so it's seem they work fine too.
Partition mapping seems good, using adb to restart the phone in recovery, download or normal mode work fine, so if i try to reboot from android's menu, it boot in recovery mode.
Does anyone have some help or infos to help me to solve this problem?
Is it possible to "re-map" the key combinaison for turning up the phone?
Thank in advance
Kev