*****EDIT*****
I kept at it and decided to restart my computer. The attempt using PrinceComsy and VZW_G930VVRU2APE1 failed. However, using Odin 3.12.3 and G930VVRU4API3_G930VVZW4API3_VZW, I had success!!! I guess the old adage of always restart your computer paid off this time. Thanks.
*****END EDIT*****
Hello all,
I'm newer to this forum. I used the GUIDE: ROOT, install XPOSED, and UNROOT/returning to stock a Galaxy S7 or S7 Edge post (https://forum.xda-developers.com/ve...-to-notes-root-install-xposed-unroot-t3411039) to root my Verizon Samsung Galaxy S7 in an attempt to recover lost photos and videos (the files just disappeared when the phone got full). I was able to root without issue, including following the recommended next steps and installing xposed. However, now that that adventure is done, I am attempting to unroot to the Verizon stock firmware, all attempts so far have failed.
The original Verizon stock for the S7 was 6.0.1. My first attempt to unroot was using the suggested firmware VZW_G930VVRU2APE1 using Odin3_v3.12_PrinceComsy. I loaded the proper AP, CP, and CSC files in Download mode (ID:COM was blue and showed as 0:[COM6]). After running this, it failed (see log results below). At this point, I was unable to boot the phone (nor could I shut it down) and got a system update failure error screen. I was able to get back to Downloading... and attemped to unroot to G930VVRU4API3_G930VVZW4API3_VZW using Oden 3.12.3. Same errors. I will admit, I attempted adding the BL file on a second try based on another site's recommendations. That failed, too. So now, I'm at a total loss as to what to do, and do not know how to fix this.
Does anyone have any ideas? Thanks much!
Unroot Using Odin 3.12 PrinceComsy to VZW_G930VVRU2APE1 (AP, CP, CSC)
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Unroot Using Odin 3.12.3 to G930VVRU4API3_G930VVZW4API3_VZW (AP, CP, CSC)
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Message on Phone Downloading Screen
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-G930V
CURRENT BINARY: Samsung Official
SYSTEMSTATUS: Custom
FAP LOCK: ON
QUALCOMM SECUREBOOT: ENABLE
RP SWREV: B4(2, 1, 1, 1, 1) K1 S3
SECURE DOWNLOAD : ENABLE
SW REV CHECK FAIL : [system]Fused 3 > Binary 1
Running on Windows 7 64-bit
Did you do anything else differently after restarting your computer? I keep failing trying to unroot -- I've restarted multiple times but still no cigar
One question about your root, did you root when you had 6.0 or 7.0?
Related
it seems to be that I did it totaly wrong when flashing my phone. I get a bootup: "Firmware upgrade encountered an issue." bla...
What did happend:
I had a custom rom from here (Android 4.3): "PACman v4.3 Build 1 nightly 20130909".
My baseband version was (as far as I can remember): XXUBMF8
I wanted to update to 4.4.2 and at first I tried to update the bootloader and modem with Odin 3.09
For bootloader I used this:
BL_I9505XXUFNAD_481100_REV06_user_low_ship_MULTI_C ERT.tar.md5
For modem I used this:
I9505XXUFNC9_GSM_LTE_Modems.tar
The flash with Odin was succesfull and it restarted. Unfortunately I coulnd find any changes in the settings windows under Android. There was still the old version under baseband (I think XXUBMF8) which was strange for me becaue of the flash. I also checked the baseband with a baseband checker tool and it was the same old version. I trayed the flash process a several time and it was always succesull but with no change in the settings.
Anyway, I flashed than a custom rom:
I9505_Omega_v28_XXUFNC9_md5_7C1D639DBBE5C01FE689DA F3B82406AC.zip
FLash was succesfull and Android started.
Under settings, still old baseband: XXUBMF8.
So I decided to update this (this was my first big mistake)..
I used Odin and flashed again the bootloader
BL_I9505XXUFNAD_481100_REV06_user_low_ship_MULTI_C ERT.tar.md5
And from here I get the error message "Firmware upgrade encountered an issue."
Than - maybe my second big mistake - I tried to flash a stock rom to reset my phone. but I used an downgraded version...
[rom]i9505][xxubmf8][4.2.2] (24.06.2013)
I check also during the flashing process with odin "re-partition" and used the pit file and the 4 other files of this firmware. the flash process didnt go to the end, it interrupted. maybe because of the repartition, it goes more and more wrong...
I can still enter the download mode. But what should I try to flash now?
Is it possible to unbrick in my situation...?
And should I use the pit file "CSB_signed_Fusion3_EUR_0325_V2.pit" or should I leave it (just use the firmware?)
Should I use 1-file or 3-file version for odin?
I would appreciate your help a lot. I need the phone for work tomorrow. It is very important for me. Sorry to hustle and thank you very very much!
tried to flash I9505XXUFNAD. added pit file + 4 files (bl, ap, cp, csc) to odin. but I cant run the flash till the end.
without the pit file it doesnt want to start. i used "CSB_signed_Fusion3_EUR_0325_V2.pit" as pit file.
this is my error log...:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I9505XXUFNAD_481100_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I9505XXUFNAD_481100_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_I9505XXUFNAD_481100_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXX_I9505OXXFNA2_549230_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
ok...
after hours of searching....: changed the usb slot.... than it managed to flash....
Hi,
I am trying to use this package, http://forum.xda-developers.com/showthread.php?t=2678124, to unbrick my samsung s4, SGH-I337M, with telus. Every time I run odin I get this output:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_I337MVLUFNC1_880525_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_I337MVLUFNC1_880525_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_I337MVLUFNC1_880525_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OYA_I337MOYAFNC1_880525_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
I tried running it three or four times and I get the same error. I have also tried other packages that I have found online and they all give me the same error as well.
My phone is currently soft-bricked, every time I turn it on it takes me to a screen that says:
"Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again."
I tried to recover it using Kies, but it doesn't recognize the device, however Odin does recognize the device.
I have tried on multiple usb ports, and different computers, all with the same error.
Any suggestions on what to do next would be greatly appreciated.
Hi Guys
Was running a custom N7 rom by Laypota decided in my wisdom that i would wipe before in updated to a new version of his rom unfortunatley i wiped more than i wanted to and now i am left with a phone that wont boot i cannot access recovery mode but can access download mode i went to samobile and downloaded a stock firmware for my phone went into odin and here is the error i am getting any help would be very appriciated thanks
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1203)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> FAIL! (DeviceInfo)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/005> Added!!
I'm trying to reflash Oreo to my Verizon S8. I have downloaded the latest SM-G950U VZW Oreo 8.0.0 firmware using SamFirm. Latest Samsung USB drivers and Odin 3.13.1. However when I run Odin, it fails almost immediately with the output below. I have tried using an older version of Odin along with the modded 3.13.1 version found on XDA and it fails at the same spot. Have tried with all 3 USB ports (2.0 and 3.1) on my laptop and 2 different OEM usb cables and none of them fix it.
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 4706 M
<ID:0/004> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
I'm having the same exact problem with my Note 8. Have you been able to solve this yet?
AJW6381 said:
I'm having the same exact problem with my Note 8. Have you been able to solve this yet?
Click to expand...
Click to collapse
Yes. I had to use a different computer. Not sure why it mattered, but I used the latest version of Odin, same firmware files, OEM cable, latest samsung usb drivers, and android adb drivers. Didn't change anything besides the PC and it worked. Hopefully it solves your issue too, good luck.
Hi i was trying to flash a new rom to my s7 edge so i downloaded what i thought was a good rom to use. However, when i did the flashing using Odin, it now boots directly to recovery, and when i click on the reboot system, it goes to a screen that says SBL ERROR UPLOAD MODE and that pretty much stays there. I am so confused and frustrated now because i just don't know what else to do. I can boot to the download mode, however, all the models i have tried(s7 edge sm-935v) do not get past the FAIL! SHA256 is invalid error. PLEASEE any help would be highly appreciable.
this is the log i get in odin
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1301)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 5305 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> FAIL! SHA256 is invalid
<OSM> All threads completed. (succeed 0 / failed 1)