Related
17/9/2010 EDIT: With a lot of feedback from this thread and other threads, it has come out that, waking up the phone with the YES/CALL/SEND green button is BETTER than waking up with the NO/END/POWER red button for SOD reasons.
----
Hello guys,
You probably know I am actively in the Android HD2 porting community.
I am having the strangest touch screen problem. I am really experienced into winmo and android stuff. Please read carefully.There is a surprise at the end.
BOTH under Android AND Winmo my touchscreen works just fine after bootup.
It first started like this:
At first my touchscreen stopped responding when I hold no button to make a reboot/power off. I thought it was from the usual Android touch screen freeze related to g sensor. Then I realized that it was the same in Winmo! Holding no button ALSO caused touch screen to die even under winmo.
Then it started loosing touch after sleeping. My touch is ALWAYS working when I boot winmo OR android and works for hours if not put to sleep. But it stops working after putting it to sleep.
Frustrated,
I restored with spb backup. Didn't work.
I reflashed my winmo rom. Didn't work.
I made a hard reset. Didn't work.
I removed sd card. Didn't work.
I removed sim card. Didn't work.
I changed the date. Didn't work. (this was a strange fix for some blackberries)
I flashed original 1.66 Turkish rom, 2.07 original old radio, even original 1.42 SPL which makes this hd2 fully stock the day I bought it. Even made another hard reset. Still didn't work!
By this time it's obvious this is a hardware problem and needs warranty.
OK
THEN I FOUND THE STRANGEST THING:
If I wake up the phone with ANY hard button other than the NO/HANGUP button touch screen WORKS!!! (Yes/Send button under Android)
BELIEVE ME, I HAVE TRIED FLASHING REFLASHING RESETTING AND TESTED 100 TIMES and YES it is ALWAYS the same. This is not a random thing.
If I wake up my phone with No button under ANDROID OR WINMO, my touch doesn't work. But if I wake up with back button windows button home button yes button, the phone wakes up properly AND touch works. Android of course doesn't work with the original radio, so I wasn't launching Android with the last test.
HOW IS THIS POSSIBLE AT ALL?? It looks like hardware fault, but touch loss IS related to NO button!
I will send my phone to warranty anyway but it will happen after the holiday (not before mid september)
IF ANYONE have an issue like this, PLEASE post.
I just want to make sure this issue isn't related to Android porting. If it is, this might be an important info. Maybe it may help devs fixing the general touch screen and wake up problems. Also everybody TRY waking up Android with the yes/send button to see if it helps with your wake up or sod issues and provide feedback. Also it may help with the phone not responding after hangup in Android. There is something hardware going at the background with the no/hangup button. I know this issue is hardware fault but still may shed light to our problems with touch screen and wake up issues. Maybe there is something hardware or firmware inside the phone waking up the digitizer. I know that hangup/no/end button is internally different than the other buttons, something like it shares the power button function that is usually on the top of the device with other htc devices. (Mine is a european hd2 and the hangup button is not red) I also wasn't using an overclocking kernel.
Please think twice before posting, and don't post anything useless. I am absolutely no noob, you can search my previous 200+ posts. I wouldn't post anything unless I am definitely sure. And I have a feeling that this thread has the potential to help or make something come out. If it doesn't, no harm done.
since most of the time inwinmo or android the no or yes button pop up generally on the same side in both os's and , taking in consideraton it might be a hardware issue , i would say you issue might be a harsware issue undr the screen when you touch no...wild guess
I was the same problem.... but it is even worst for me now...
Before, at least work touch others buttons... now my touchscreen DON'T WORK. :-(
I suppose that it's a hardware problem :-(
memin1857 said:
Hello guys,
You probably know I am actively in the Android HD2 porting community.
I am having the strangest touch screen problem. I am really experienced into winmo and android stuff. Please read carefully.There is a surprise at the end.
BOTH under Android AND Winmo my touchscreen works just fine after bootup.
It first started like this:
At first my touchscreen stopped responding when I hold no button to make a reboot/power off. I thought it was from the usual Android touch screen freeze related to g sensor. Then I realized that it was the same in Winmo! Holding no button ALSO caused touch screen to die even under winmo.
Then it started loosing touch after sleeping. My touch is ALWAYS working when I boot winmo OR android and works for hours if not put to sleep. But it stops working after putting it to sleep.
Frustrated,
I restored with spb backup. Didn't work.
I reflashed my winmo rom. Didn't work.
I made a hard reset. Didn't work.
I removed sd card. Didn't work.
I removed sim card. Didn't work.
I changed the date. Didn't work. (this was a strange fix for some blackberries)
I flashed original 1.66 Turkish rom, 2.07 original old radio, even original 1.42 SPL which makes this hd2 fully stock the day I bought it. Even made another hard reset. Still didn't work!
By this time it's obvious this is a hardware problem and needs warranty.
OK
THEN I FOUND THE STRANGEST THING:
If I wake up the phone with ANY hard button other than the NO button touch screen WORKS!!! (Yes button under Android)
BELIEVE ME, I HAVE TRIED FLASHING REFLASHING RESETTING AND TESTED 100 TIMES and YES it is ALWAYS the same. This is not a random thing.
If I wake up my phone with No button under ANDROID OR WINMO, my touch doesn't work. But if I wake up with back button windows button home button yes button, the phone wakes up properly AND touch works. Android of course doesn't work with the original radio, so I wasn't launching Android with the last test.
HOW IS THIS POSSIBLE AT ALL?? It looks like hardware fault, but touch loss IS related to NO button!
I will send my phone to warranty anyway but it will happen after the holiday (not before mid september)
IF ANYONE have an issue like this, PLEASE post.
I just want to make sure this issue isn't related to Android porting. If it is, this might be an important info. Maybe it may help devs fixing the general touch screen and wake up problems. Also everybody TRY waking up Android with the yes button to see if it helps with your wake up or sod issues and provide feedback. Also it may help with the phone not responding after hangup in Android. There is something hardware going at the background with the no button. I know this issue is hardware fault but still may shed light to our problems with touch screen and wake up issues. Maybe there is something hardware or firmware inside the phone waking up the digitizer. I know that hangup/no/end button is internally different than the other buttons, something like it shares the power button function that is usually on the top of the device with other htc devices. (Mine is a european hd2 and the hangup button is not red) I also wasn't using an overclocking kernel.
Please think twice before posting, and don't post anything useless. I am absolutely no noob, you can search my previous 200+ posts. I wouldn't post anything unless I am definitely sure. And I have a feeling that this thread has the potential to help or make something come out. If it doesn't, no harm done.
Click to expand...
Click to collapse
BIt strange this one to be honest I think it may just be your device as there are now hundreds of users of android on the hd2 and this is extremely rare. Hopefully a dev will look into and find a possible solution but I doubt it. If I was you I would put it back to stock and send it off to HTC for a new one. Even if a dev manages to find the problem you will have a new or as new hd2
I have been trying and I must say that I sort of do share your experience. The most left button (referred to as yes) awakes the phone just right as where the most left (No) takes its time to start the phone. I haven't had any noticable touch issues that could be related to these hard buttons yet.. (I think)
But I do think you have a point.
Interesting, I had something similar. I was using elegancia rom v1 for the longest time, with all my android builds, no problems. Then I went to chunkydroid rom, and had a few issues, with multiple android installs (one of which was my original that was working before.)
Then I rebooted into chunkydroid, (windows), and had the same issue. It was strange. I tried a few other roms, same problem. Turned off the phone, next day, reflashed chunky again, and hyperdroid 1.1, no issues since. (Only difference, which I don't know if it's related, but again, might help, is that I was overclocking. I have since not let anything go above 998 in setcpu, and even removed all builds that were overclocking. I though it might have had something to do with it (and the phone wasn't warm at all.)
I have not been able to duplicate the problem since though (even with overclocking just to see). So I'm pretty stumped. I'm sure the devs will work it out.
I have taken to pressing the yes/send key to wake up my phone as it seems more consistent than pressing the end key. My theory is that multiple wake up/sleep messages are being sent on the end key and the system gets confused. Some sort of debounce might help.
Just my thoughts.
Running shui8 realstock rmnet with micyprima r9.
It seems waking up the phone with the Yes/Send button somehow seems better with current builds and kernels.
I am asking everybody reading this thread to try waking up their Android devices with the yes/send key and share their experience if it is making their Android wake up quicker with less SODs.
Note: I am still using yes key wake up as a workaround for my hardware touchscreen fault. Still absolutely works everytime. I found out that if I accidentally try to wake up with the no/hangup key I need to wait about 10-15 seconds before yes/send key does its magic again.
well, i tried there is absolutely no difference between any hard button. if i have sod, none of them solves... actually its not sod i think, when you try to put standby and wake up several times quickly, screen stops responding for a while. you need to wait at least 15 seconds between each standby and wake up. can i fix this? or this is the sod?
Waking up with the yes/send button would not make any difference if your phone can wake up good with the no/hangup button already. But we are trying to find out if yes/send button wakes up better in long term usage. (no/hangup button sometimes can't wake up and that is the sod refers to)
SOD happened to me few times too with the NO/Hangup button and if/when that happens, if you press NO/Hangup button for long(for the menu with the turn off the phone,reboot,plane mode,...etc options) screen comes back BUT sometimes it locks the screen brightness to lowest possible setting(with %0 actually it doesn't completely turns off as you know).
Other than that "bug" NO/Hangup button works fine for me but as the OP, YES button is more stable and no SODs happen with the YES button...
Btw there is no difference for me YES button vs NO/Hangup button by means of quickness... Both works the same speed unless of course there is no SOD with the NO/Hangup button...
Just wanted to share my experience...
This thread is awesome
Thanks for this thread. I have been trying to use any android build for at least a full day with no success. Ive used different winmo roms and radios such as chucky and miri roms. I still ran into sod's. After waking with the yes/button i have had no sod issues since then, Once again awesommmmmmmme thread.
After some time my digitizer died almost completely. (Issue became worse) It is currently being handled under warranty. (digitizer is replaced)
But at least with a lot of feedback from this thread and other threads, it has come out that, waking up the phone with the YES/CALL/SEND green button is BETTER than waking up with the NO/END/POWER red button for SOD reasons.
any solution to this issue yet because i just started having this exact same problem w/ my HD2 yesterday before that it was perfectly normal and all the suddon the Power/END/NO button wake up cause the screen to not respond to the touch at all however wake up w/ home,back,menu,call button the touch screen works is back to normal
still can't figure out if its a hardware or software problem cause i also tried flashing bunch of roms/radios/and android roms as well and even went back to stock rom in hope for a solution
waking with green is about 2s faster for me.
Same thing happens to me before 2 days.I tried many hard resets,roms,radios and my screen didnt work.I couldnt even login in wm.
My screen was completely dead.The last thing i did,before my screen goes unresponsive was to push no/hangup button in android to open it
At first also i thought it was a g-sensor issue,but then realise that it was much more than it.
Until the moment i read this thread
The way it worked for me
I open the device with no button of course,made a soft reset from red hole and i wait until the device goes to standy itself.Then i open it from send button and voila touch is back !!!!
Strange thing but it works.Thank you very much you are a genius
sure the touch comes back when it wakes up using all other buttons except the power/end button so why is that all the sudden the power/end button causes the screen to go unresponsive
like for say when i hold the power/end key to open the pHONES OPTIONS in windows or android once the PHONES OPTIONS shows up and i try to click on power off or reboot on the screen the touch doesn't respond so the only way to reset or power off the device completely is the either use the reset button in the back or pull the battery out
i'm going to be sending it under warrenty/insurance to t-mobile and hopefully get a replacement cause i'm so use to the power/end button to wake up my device...
Guys be extremely carefull when using hard buttons in android.Finally my problem with screen is not the end button but the back arrow button.This button is necessary for using android and i have pushed it many many times the last months as i am using android.Νοw every time i pushed it my touchscreen stops responding.Τhe last time i pushed it my screen stopped responding(i thought for ever) and didnt knew the exactly reason that this happens.Because i didnt want to send the device to htc (firstly i must send it to expansys in france and they will send it to htc) and take it back at christmas i decided to go to a local mobile service.I wasnot mind for warranty cause i wouldnt be able to live 4 weeks without hd2.I was ready to give 600euros to buy desire hd
Result from service
At firstly he said to me that hd2 have no touchscreen problem and it works ok
I paid 20euros for opening the device and took it back.At first 5 minutes my screen stopped responding again and didnt knew the reason.For my good luck i leave the device untouched 10 minutes and the screen come back again.Then i used it and the time i pushed the back button the screen stopped working,fortunatelly for little seconds.Now i know.My screen stop responding when i push back button.So i change the keylayout to my android build and now i push send key instead of back and volume up key for menu and volume down for power on-off and hd2 works perfect after 24 hours without touching the back button
Also in monday i will go to service again to fix the button problem
Same issue with me
Exactly same issue with me. I have been using Winmo and Android on and off in my HD2. couple of weeks back, touch didnt respond after waking up the device from standby by pushing endkey.
tried everything - flash/stock rom/removed SD card/ hard reset/clear storage/custom rom/ battery pull out etc...
touch worked suddenly and only when i slightly touch the end key instead of pushing it fully, the start menu opened..this happened for few days and when ever i push the end key...screen goes unresponsive. all other hardware buttons are working fine and if at all i push end key the issue starts.
unfortunately my friend pushed the end key once and the screen never responded after this....now am using my old p3450 htc touch...
i think if we change the AP BOARD (Flex ribbon-keyboard chip) everything will go back to normal coz its not the problem with digitizer or the lcd of the software for sure.
trying to order one in ebay, we can change this ourselves...no need to send it to service centers and waste money on it.
if any of you have done this already...let me know if it worked for you.
guys dont know if it is allready known but there is a app called sidebar style swkey
http://forum.xda-developers.com/showthread.php?p=9726110#post9726110 which puts software buttons in the screen.This app is definitely button saver
this is a new problem for me. I have been using the most recent Dutty ROM together with Mdeejay Android ROM without any problems. All of a sudden, when I try to unlock the screen after STANDBY, it just wont register my touch, as if I am not touching it. It boots up fine, and on the first unlock works fine, but when the screen lock goes on again (after every standby) it just wont unlock. So I am stuck (I use Exchange and our policy forces the lock after standby, so I have to use it - and its worked fine for ages).
If I boot into Android, it works fine, the unlock works fine, yet strangely when I try to shut the power down, THAT screen also doesnt register me touching it.
I have hard reset but even before I load an app or do anything, the problem exists.
I also reflashed a DUTTY ROM. Same problem.
I tried CHT lockscreen - same issue. After Standby, screen doesnt register my touch.
Anyone have any ideas?
Same problem for me.. Restoring a backup image after being forced to hard reset this morning and now suddenly my HD2 won't wake up after sleeping. Pressing my end key only lights up my buttons but I have to pull the battery to reset. I'm thinking it's related to me having CHT installed, yours however might be a different problem.
I had something similar. It was right after I had installed CHT 2.0 and was looking to make the top and bottom bars transparent. I found a cab that claimed it would do this and installed it. Sorry, I don't recall what cab it was and I have deleted it. When I rebooted Sense would hang and if it got into a lock it would only move the slider a little where it would stop. Luckily, I had done a backup that morning right after I installed CHT 2.0 with Sprite so I restored and all was well.
I don't know if this is of help but I figured I'd throw it out there.
it wakes up, but wont register when I try to swype the unlock screen.
ekerbuddyeker said:
it wakes up, but wont register when I try to swype the unlock screen.
Click to expand...
Click to collapse
Your lucky you get that far lol.. I don't get any waking up. Plus I now uninstalled S2U2 and still no change. Disabled all locks of any kind and still frozen with sleep of death with in 1 min of hitting power to sleep it. I REALLY don't want to to a hard reset and install everything from scatch.. UGH.
weird update...
It has something to do with which key i witch the device on with. If I use the phone key, I can swype the unlock. If I use the power key, it doesnt register.
Another related issue: when i hold the power key to switch off, it wont register me touching power off or reboot etc. so I have to take the battery out to switch off. Its the same in Android.
Anyone know? Hardware issue?
ekerbuddyeker said:
weird update...
It has something to do with which key i witch the device on with. If I use the phone key, I can swype the unlock. If I use the power key, it doesnt register.
Another related issue: when i hold the power key to switch off, it wont register me touching power off or reboot etc. so I have to take the battery out to switch off. Its the same in Android.
Anyone know? Hardware issue?
Click to expand...
Click to collapse
bump this is horrid
same
im having the exact same issue. I have flashed 3 different roms and flashed to the newest radio (2.15).
I started out using energy rom, didnt help. Flashed a newer energy rom, didnt help. Now im using the dusk rom, same issue.
SOMEONE PLEASE HELP!!!!
It's a quite common digitizer problem lately... it seems the HD2's digitizer is failing on some units, possibly because of usage with android? my father's device acted the same way, only it sometimes did register touch and other times, not.
My device doesn't have these problems, yet. But seeing that a lot of people here are experiencing these issues, and with the notion that I use android pretty much all the time since I first booted my device, i'm pretty sure i'll experience it soon as well..
Make no confusion thou, the assumption that android effects the digitizer are purely my own thoughts on this matter, no such thing has been proven and the conclusion that android is effecting our HD2s is based purely on the statistics of touch screen failures in the last few months since android has been made publicly available in a working form.
EDIT:
Those seeking A solution, as far as I know, the only solution is sending your unit to HTC for repairs, you'll get it back with a note that says that they replaced your digitizer or your screen, at least these are the reports I heard from the other folks whom followed this procedure.
Good luck.
HTC HD2 Screen Lock
I have only used Android a few times on this 'phone and it has a standard HTC/O2 ROM installed so it must just be a problem with the top part of the digitiser. With android running the unlock is at the bottom and is unaffected.
Is there any way of testing the digitiser before deciding whether to get a repair sorted,
Ta,
link:
htcphones.net/htc-hd2-problems-with-touchscreen
short version :
change digitizer
ekerbuddyeker said:
weird update...
It has something to do with which key i witch the device on with. If I use the phone key, I can swype the unlock. If I use the power key, it doesnt register.
Another related issue: when i hold the power key to switch off, it wont register me touching power off or reboot etc. so I have to take the battery out to switch off. Its the same in Android.
Anyone know? Hardware issue?
Click to expand...
Click to collapse
A friend was complaining to me about something like this since last week. I could not figure it out so I went ahead and installed Android cm7 and still have the same issue.
Until I read this post after searching through the forums all over Screen now unlocks perfectly fine but only using the green Phone icon. If I try to wake the screen with the red Power button, the screen is unresponsive.
Thanks for the info.
Already happened tome its a hardware issue can't be fixed so if you still have warranty on ur phone send it to htc for repairs b because it tends to get worse n worse soon other keys will start to give in I think that's one reason why most android phone been switching to capacitive buttons because hardware causes this sorta issues and send it in for repairs to get it fixed
Sent from my SGH-T959 using XDA App
the same issue with me , is there is any solution for that .
Wakeup the phone using the send button.it will work
Alright, so here's my problem. My touchscreen won't response to any finger movement. I could press the hardware buttons like power, volume and talk and it response to that but my problem is mainly trying to get inside my rom. I tried flashing rom via NAND and via clockwork mod and nothing helps. The G Sensor seems to work just fine because it rotates the screen when I'm inside my ROM. I could go back into MAGLDR but I don't think anything there is going to help?
Has anyone else experience anything like this and if so, what did you do to solve it?
had same problem, found a FIX
i have had same problem past couple of days. i was running darkstones SuperRAM_FroYo_V1.5 build with oz 2 cleanex rom. i know that every now and again it would be a pain to unlock the device with the agonising wait for the lock screen to show up but this time the touch screen would not work at all not recognising any movement and not dragging the unlock button across. i would have to take the battery out and restart, even some times touch screen would fail completely when in winmo too, got to a point when 3 days of working then not working and taking the battery out a million times to boot back into android to unlock the device, then touch screen died completely.
FIX- Hard reset
will reset windows mobile. all data on device will be lost.
hold down up-vol key and down-vol key, soft reset button and then power button till it displays formatting screen. follow on screen instructions.
hope this helps.
tidygrant said:
i have had same problem past couple of days. i was running darkstones SuperRAM_FroYo_V1.5 build with oz 2 cleanex rom. i know that every now and again it would be a pain to unlock the device with the agonising wait for the lock screen to show up but this time the touch screen would not work at all not recognising any movement and not dragging the unlock button across. i would have to take the battery out and restart, even some times touch screen would fail completely when in winmo too, got to a point when 3 days of working then not working and taking the battery out a million times to boot back into android to unlock the device, then touch screen died completely.
FIX- Hard reset
will reset windows mobile. all data on device will be lost.
hold down up-vol key and down-vol key, soft reset button and then power button till it displays formatting screen. follow on screen instructions.
hope this helps.
Click to expand...
Click to collapse
well i have woke up this morning to be able to unlock my device to then locking it and not being able to unlock it again!!! i had notification to say it had managed to restore 16 apps whilst i had been asleep so i am thinking there is a dodgy app out there some were
mazdarider23 said:
Alright, so here's my problem. My touchscreen won't response to any finger movement. I could press the hardware buttons like power, volume and talk and it response to that but my problem is mainly trying to get inside my rom. I tried flashing rom via NAND and via clockwork mod and nothing helps. The G Sensor seems to work just fine because it rotates the screen when I'm inside my ROM. I could go back into MAGLDR but I don't think anything there is going to help?
Has anyone else experience anything like this and if so, what did you do to solve it?
Click to expand...
Click to collapse
Sent from my PC36100 using XDA Premium App
I have this problem and have found no way to fix it, I have tried everything except possibly going to the clk loader instead of magldr. when i put the phone to sleep with the power button is when i have the issue of not being able to unlock my phone in Android. I have tried task 29, going back to original windows roms, sd and nandroid, it is a hardware issue related to the digitizer as far as I'm concerned. I love my HD2 and really need to fix or find another one. I know this doesn't help, but maybe a little more insite if nothing else
I had the same issue. With my 1st HD2 it started as an intermittent problem, then eventually completely stopped working. With my replacement it just started to happen again. I immediately flashed back to stock tmo windows and the touchscreen would work so long as I did not try and put the phone on standby or wake the phone using the end key. If the phone went to standby on its own, the touchscreen would not work either. I changed the settings so that the phone would not go into standby at all. I then learned that locking the phone from the windows menu and allowing it to go to standby that way somehow averted the touchscreen problem. After 2 days, the problem seemed to resolve itself, almost completely. If I try and wake it using the end key, the touchscreen still wont work, but every other button on wake works. Also, putting it in standby with the end key seemed to not cause the problem any longer.
I dont know if the issue varies per person, but what worked for me was going to stock windows for a couple of days, then starting over with android. I guess it depends on how far along the problem has progressed.
Look at my thread in my Sig about the Unresponsive Screen Solved. This sounds exactly as that. And there are various workaround solutions through out the post.
Hi All,
My OPO2 becomes not responsive at all after keeping the screen off for more than 1-2 seconds.
Turning on and off the screen fast works well.
It is not really powered off because:
1. I can call to it, but there is no ring and no option to answer.
2. In order to turn it back on, I must long press the power button.
If I keep the screen on the phone works just fine for long hours.
I've tried factory reset, and even switched the stock OS with CM - and the issue reoccurred.
Happening only when unplugged.
Any ideas what else I can try?
Appreciate very much the help.
Same happened with my other Android device it would go unresponsive after I lock the screen I think it is a hardware related may be your proximity sensor is faulty check with service center.
Kons22b said:
Hi All,
My OPO2 becomes not responsive at all after keeping the screen off for more than 1-2 seconds.
Turning on and off the screen fast works well.
It is not really powered off because:
1. I can call to it, but there is no ring and no option to answer.
2. In order to turn it back on, I must long press the power button.
If I keep the screen on the phone works just fine for long hours.
I've tried factory reset, and even switched the stock OS with CM - and the issue reoccurred.
Happening only when unplugged.
Any ideas what else I can try?
Appreciate very much the help.
Click to expand...
Click to collapse
Full wipe and try reflashing stock oxygen os 3.0.2 it may solve ur problam
Solved!
Hi,
Actually I had the capacitive buttons and the home button not working at all either,
so in this case it came into my mind that they may cause this issue to happen.
I have simply disconnected them both from the motherboard and the problem solved!
Obviously, replacing them is an additional option.
Thank you everyone for the help
My OP5 screen had a small crack so I decided to repair it. After following the tutorial on youtube step by step the phone powers up fine. But as soon as the screen goes to sleep, it get stuck in black, although it feels like responsive (Ican hear the clicks and vibrates and all) but it wont wake up
imercado said:
My OP5 screen had a small crack so I decided to repair it. After following the tutorial on youtube step by step the phone powers up fine. But as soon as the screen goes to sleep, it get stuck in black, although it feels like responsive (Ican hear the clicks and vibrates and all) but it wont wake up
Click to expand...
Click to collapse
Could you wake up the screen? Maybe it's a connection problem or related to the proximity sensor?
Did you ever find a solution to your problem? I have exactly the same problem, but it happens only with Android 9.0. Oreo seems to be working OK, but as soon as I upgrade to official 9.0, the screen won't wake up from sleep. The backlight turns on, but the screen stays black. The phone works OK as long as I use it, but if I press the power button or let it to enter "standby mode", it will stay that way (off). I suppose it has something to do with the replacement screen, but since it works with 8.0, I wish there was a workaround to get the LCD to work with Pie too.
Same problem here. Replaced display too.
I've had a similar issue with a different device before (ZTE nubia Z7 mini). I replaced the screen and it would work correctly, but when I booted TWRP, I would get a black screen. I figured that because the replacement screen was not an OEM one, it may have something to do with LCD drivers in the recovery. I used the old cracked screen with the device opened up to navigate in the TWRP recovery, and I flashed an newer/different recovery. Voila, the new recovery worked with my replacement screen. Based on this experience, it may just be an LCD driver compatibility issue with the replacement screen, causing the screen to just go into forever sleep mode. The driver may need to be changed or tweaked in the Pie version for your replacement screen to work with it. Just a thought, not fully certain.
iwantademo123 said:
I've had a similar issue with a different device before (ZTE nubia Z7 mini). I replaced the screen and it would work correctly, but when I booted TWRP, I would get a black screen. I figured that because the replacement screen was not an OEM one, it may have something to do with LCD drivers in the recovery. I used the old cracked screen with the device opened up to navigate in the TWRP recovery, and I flashed an newer/different recovery. Voila, the new recovery worked with my replacement screen. Based on this experience, it may just be an LCD driver compatibility issue with the replacement screen, causing the screen to just go into forever sleep mode. The driver may need to be changed or tweaked in the Pie version for your replacement screen to work with it. Just a thought, not fully certain.
Click to expand...
Click to collapse
You're probably right about the driver issue. My OP5 has no problems whatsoever with Android 8.1, but 9.0 won't work no matter what I do after waking up the device. The backlight turns on and and off for a few times after which nothing happens. The phone is still working normally, but it's in "blind mode" (music will continue playing, volume buttons work...but they're kind of slow and laggy) Too bad that the latest update (9.01) didn't fix this issue either. I really wouldn't hold my breath getting this issue fixed anytime soon (officially) as it seems to be a cheap 3rd party screen problem.
edit: I tried the custom recovery (20181227) and the same thing happens there. Once screen goes off, it won't come back on.
Edit 2: gave up on the replacement screen and ordered an oem lcd. Lets see how it goes.
sbasil said:
You're probably right about the driver issue. My OP5 has no problems whatsoever with Android 8.1, but 9.0 won't work no matter what I do after waking up the device. The backlight turns on and and off for a few times after which nothing happens. The phone is still working normally, but it's in "blind mode" (music will continue playing, volume buttons work...but they're kind of slow and laggy) Too bad that the latest update (9.01) didn't fix this issue either. I really wouldn't hold my breath getting this issue fixed anytime soon (officially) as it seems to be a cheap 3rd party screen problem.
edit: I tried the custom recovery (20181227) and the same thing happens there. Once screen goes off, it won't come back on.
Edit 2: gave up on the replacement screen and ordered an oem lcd. Lets see how it goes.
Click to expand...
Click to collapse
Do keep us updated if changing the display again fixes this issue. Would be interesting if someone had a fix for 3rd party displays but as of now it seems that's highly unlikely
]
iwantademo123 said:
Do keep us updated if changing the display again fixes this issue. Would be interesting if someone had a fix for 3rd party displays but as of now it seems that's highly unlikely
Click to expand...
Click to collapse
Sure.
Got the new OEM amoled screen today. It's brighter, more responsive and doesn't get stuck (black screen) with Android Pie. Problem solved. Price was 3 x higher than the cheap 3rd party screens, but definitely worth it (around 80 euros). All screen gestures work as well.
Bought it on Witrigs (https://www.witrigs.com/oem-lcd-screen-assembly-for-oneplus-5-midnight-black). it came really well packed and arrived fast (7-10 days to Finland). I highly recommend this screen and Witrigs to everyone
Also changed the screen from a friend and have this strange behavior, that the screen won't turn on .. only when I reboot or double press the power button so it launches the camera - the delay tho is about 7s, which is insane! you guys think this is the screen problem, or did I damage something and if yes, what? I repaired about 100 phones in total already ..
Link to the video: https://youtu.be/QmkBspymv8w
androidfreak11 said:
Also changed the screen from a friend and have this strange behavior, that the screen won't turn on .. only when I reboot or double press the power button so it launches the camera - the delay tho is about 7s, which is insane! you guys think this is the screen problem, or did I damage something and if yes, what? I repaired about 100 phones in total already ..
Link to the video: https://youtu.be/QmkBspymv8w
Click to expand...
Click to collapse
Sounds a lot like my OP5 with cheap 3rd party screens which would hardly work at all with Android Pie. If your friend's phone is running on Pie, try downgrading it to Oreo and see if that helps. My phone worked moderately with Oreo but not at all with Pie (wake and touch issues). Currently my OP5 is running Android Pie perfectly with the screen that I bought on Witrigs.
androidfreak11 said:
Also changed the screen from a friend and have this strange behavior, that the screen won't turn on .. only when I reboot or double press the power button so it launches the camera - the delay tho is about 7s, which is insane! you guys think this is the screen problem, or did I damage something and if yes, what? I repaired about 100 phones in total already ..
Link to the video:
Click to expand...
Click to collapse
Bizarre, have you tried the usual factory reset / rom reflash? If you confirm that its not a software related issue, then it probably is just the screen if its not an OEM part. Can't see what else would be the issue here unless there was other kind of damage before the repair maybe
Like @sbasil mentioned, it could just be due to the non-OEM screen being incompatible with Pie drivers.
Thank you for saving my phone
sbasil said:
Sounds a lot like my OP5 with cheap 3rd party screens which would hardly work at all with Android Pie. If your friend's phone is running on Pie, try downgrading it to Oreo and see if that helps. My phone worked moderately with Oreo but not at all with Pie (wake and touch issues). Currently my OP5 is running Android Pie perfectly with the screen that I bought on Witrigs.
Click to expand...
Click to collapse
Thank you for saving my phone
Mine not working with lineage base rom but is good with last pie 9.0.8. Did you try it?
Have this issue too
My OP5 has its original AMOLED screen. Running OS 9.0.8. This started happening after the most recent update. At least I never noticed it before.
I ran *#808# diagnostics, thinking maybe it's the proximity sensor, or the fingerprint scanner, but everything passed.
Also while locked, ambient display works. It's just getting the Home screen to appear after waking the phone that's become agonizing. And it does wake, the touch screen is responsive, it's just completely blind.
I mean consider this: I can take a screen shot, a screen shot, while the screen is in ambient display and the screen shot is of the home screen.
Pressing the power button or home button or notification slider repeatedly sometimes coaxes it to appear, but the only sure way to get the Home screen back is to restart the phone.
I had a black screen issue after changing the screen to an OEM AMOLED one, and after tearing my hair out for a couple of hours, I discovered that turning off " night mode" fixed the problem instantly
Same happened to me... cracked screen, purchased 'OEM screen' installed. Some apps work, some just black screen.
Driver issue? Running Pie 9x. Anyone had success with this by dropping back to Oreo? Would it do anything different to flash the Pie Firmware?
I repair/upgrade OnePlus 3/3T/5/5T phones to donate to families in need at the local family shelter. Some of them have lost or had to sell their phones just to get food and such. Now they need one to arrange job interviews and housing, things of that nature. So anyways, all that to say this.... I have replaced a LOT of displays, and all of them were the 'cheap' ebay variety. Each and every time I would replace the display, the phone would act just as described in this thread.
After long hours of reading, searching, and experimenting, I have found the ultimate and final solution to this problem. The answer to this issue is simple, but was not so simple to find. Whenever anyone does a screen replacement, and the screen is not the high-priced OEM variety, their phone will almost always have extreme difficulty in waking. The fix, and it has worked for me 100% of the time, is to flash a custom kernel. For the OP5/5T the kernel I use that always works is the Affinity kernel. Just flash and forget. The phone will always wake up after you flash that kernel.
However, don't forget, that what also happens with these lower priced replacement screens is that you can no longer double-tap to wake. I still haven't found a solution for that problem, but it always happens each time I replace a screen. The kernel won't help with that. But it does fix the 'won't wake up' problem.
Try it for yourself and see. You will be happy you did!
Oblias said:
... The fix, and it has worked for me 100% of the time, is to flash a custom kernel. For the OP5/5T the kernel I use that always works is the Affinity kernel. Just flash and forget. The phone will always wake up after you flash that kernel.
Click to expand...
Click to collapse
Please, can you point which FW you're using?
d2mac said:
Please, can you point which FW you're using?
Click to expand...
Click to collapse
I'm not clear about what you are asking. What exactly are you calling FW?? Some people mean radio and camera firmware. Some people mean the custom rom that gets flashed. What do you mean?