Related
WARNING: This instruction may brick your device permanently. I am not
responsible for any your loss or damage.
The following is the instruction to get root for SGP611 with giefroot(http://forum.xda-developers.com/crossdevice-dev/sony/giefroot-rooting-tool-cve-2014-4322-t3011598)
Requirement:
Bootloader Locked Z3 Tablet Compact Wi-Fi 16GB (SGP611)
D6603(Generic GLOBAL 23.0.A.2.93) firmware (You can got it from XperiFirm)
Flashtool
Install driver included in Flashtool
Patched version of giefroot_v3 (View attachment giefroot_v3_sgp611_fix1.zip)
Download:
View attachment giefroot_v3_sgp611_fix1.zip
Small Instruction:
1.Backup
2.Flash SGP611 firmware (23.0.1.A.0.167) if other version is installed
3.Flash D6603 system partition (23.0.A.2.93)
4.Enable [USB Debug] and [mock locations] and [Unknown Source] , then run install.bat in (View attachment giefroot_v3_sgp611_fix1.zip)
5.You got root!
6.Backup TA, Back to SGP611 firmware
Instruction:
1. Backup all your data (including application data and internal storage)
2. Get SGP611(23.0.1.A.0.167) firmware
3. Get D6603 firmware(Generic GLOBAL 23.0.A.2.93 ftf) from somewhere
4. If firmware version of your device is not 23.0.1.A.0.167, then flash all
contents of ftf to back to 23.0.1.A.0.167
(Start Flashtool and click "flash device", then choose "Flashmode".
On "Firmware Selector" select SGP611 firmware.
Uncheck APPSLOG, CACHE, DATA in Wipe menu.
Check all checkbox in Exclude menu.
Unckeck KERNEL in Exclude menu.
Then click Flash button.
Shutdown your device and connect USB on holding volume down.
Wait 20minute or more to finish.
)
5. Flash only system partition of D6603 (23.0.A.2.93)
(Open "Firmware Selector" with same instruction above.
select D6603 firmware.
Uncheck APPSLOG, CACHE, DATA in Wipe menu.
Check all checkbox in Exclude menu.
Unckeck SYSTEM in Exclude menu.
Then click Flash button.
And flash with same instruction above.
)
6. Power on your device, then enable [USB Debugging] and [Allow mock
locations] in Developer options. And enable [Unknown sources] in Security
setting.
Added:
Disable [Verify apps over USB] in Developer options, and disable [Verify apps] in Security setting.
Thanks kvi!
7. Install usb driver included in Flashtool
8. Download giefroot_v3_sgp611.zip and extract zip
9. Run install.bat in extracted folder, then wait for about 1minute
10. You got root!
11. Backup TA
12. Restore stock firmware by following insruction of this thread http://forum.xda-developers.com/z3-...-to-rooted-stock-sgp621-firmware-drm-t3015494
(replace SGP621 to SGP611 in the instruction)
Thanks to zxz0O0 for giefroot and some other tools.
zxz0O0 spend so much time to make giefroot work on SGP611 kernel.
Thanks to lowtraxx for root instruction for SGP621.
(http://forum.xda-developers.com/z3-...t/root-root-locked-bootloader-sgp621-t3013534)
Thanks to CubicU07 for instruction to restore stock firmware.
The old version (giefroot_v3_sgp611.zip) does not work.
Please try new version (View attachment giefroot_v3_sgp611_fix1.zip).
I'm sorry.
For me its not working:
Got a Z3TC 16GB WIFI, installed the Z3TC ftf, then flashed the system from the Z3, then used the tool but always get a device not rooted error
moritz31 said:
For me its not working:
Got a Z3TC 16GB WIFI, installed the Z3TC ftf, then flashed the system from the Z3, then used the tool but always get a device not rooted error
Click to expand...
Click to collapse
It may not succeed in one time.
Plaese try again 3 or 4 or more times.
If you still fails, please let's me know results of commands below.
Code:
adb shell cat /data/local/tmp/giefrootlog
adb shell cat /data/getrootlog
adb shell ls -l /data/local/tmp/scsi_wait_scan.ko
rurie said:
It may not succeed in one time.
Plaese try again 3 or 4 or more times.
If you still fails, please let's me know results of commands below.
Code:
adb shell cat /data/local/tmp/giefrootlog
adb shell cat /data/getrootlog
adb shell ls -l /data/local/tmp/scsi_wait_scan.ko
Click to expand...
Click to collapse
hey, i got it the problem seems to be on one site windows10,
on my mac i had to unplug replug the device after reboot before pressing continue
I noticed a mistake.
I fixed and upload again. (giefroot_v3_sgp611_fix1.zip)
Please try new file.
This file fixes both exploit itself and install.sh(for Linux/OS X).
rooted OK disabling all options for check/verify apps ! (1 option in security + 1 option in Developer options) , Backup TA OK
TA restored on rooted stock firmware , drm keys OK
Thx!
kvi said:
rooted OK disabling all options for check/verify apps ! (1 option in security + 1 option in Developer options) , Backup TA OK
TA restored on rooted stock firmware , drm keys OK
Thx!
Click to expand...
Click to collapse
Thanks for confirming
kvi said:
rooted OK disabling all options for check/verify apps ! (1 option in security + 1 option in Developer options) , Backup TA OK
TA restored on rooted stock firmware , drm keys OK
Thx!
Click to expand...
Click to collapse
Thank you for reporting and information!
I added your information to the instruction.
FtF global z3 or z3 tablet?
edited:
I was asking if need to build de ftf firmw using z3 as device or z3 tablet, but It works with z3
Works for me, actually running stock android with root and TA partition restored.
THANKS A MIL!
I do not speak English, I use google translator
Do not know which section you mean, 5 or 12. If I did 5 you see in this picture
http: // oi59.tinypic.com / 2my85qc.jpg
Root with the bootloader intact, that is amazing! Will this also work on the WiFi 4G version? That's the one I have and I don't want to mess it up.
Angelusz said:
Root with the bootloader intact, that is amazing! Will this also work on the WiFi 4G version? That's the one I have and I don't want to mess it up.
Click to expand...
Click to collapse
Just scroll one line up in general forum you have the post for the SGP621 (LTE version) here
enjoy!
Oh, I missed that one, thanks!
Does it void warranty? As the DRM keys and still there and how to do you restore the DRM keys
Copy apps in SDcard.
If you already gained root access, can you copy all apps to SDcard? What apps you guys recommend? Thanks in advance.
Does this method erase all data in internal card?
Has anyone got this working with SGP612 yet? (32gb Wifi only version). I have't seen this mentioned anywhere, but it should be similar to SGP611?
I'm a bit confused at step 12 : first thing to do when following CubicU07 instructions is to follow ... lowtraxx instructions...
If we follow CubicU07 thread, we first have to back up TA, but that was step 11 of this current thread. sso I guess we should follow lowtraxx instructions, but this one specifies that it won't work for SGP611, and sends us to this thread. Back to square one, then.
My guess is that we have to follow CubicU07 thread, no matter what he says first (so, I won't follow lowtraxx instructions).
Could you please be more specific for step 12 ? Do we finally have to use Advanced stock kernel, PRFCreator, SonyRICDefeat, ... as described in CubicU07 thread (which also involves unlocking BL) ?
Thank you.
Where can I get the firmware from step 3?
It's written : install XperiFirm and download it with this software.
Only fresh flashed bootloader locked XT1058 AT&T - ROM LPAS23.12-21.7-1, and XT1060 VZW - ROM LPAS23.12-39.7-1 are supported!
See archive content for instructions. Time to install ~20 min. If you experience problems after Android boot, like not working buttons or quick settings, wipe cache + data partitions. Don't update SuperSU (disable auto updates), it won't work. Later I'll post complete debloated ROMs with fresh SuperSU version, and simplify instructions. Be informed also, that this method doesn't give you read-write rights like unlocked bootloader. You may read and write having root-rights, but only till a restart or shutdown occurs, and every change will be undo by the Qualcomm protection (like HTC' s=on).
At the moment patch includes:
SuperSU 2.65 Free
Xposed Framework v86 (installer, modules)
Busybox 1.25.0.YDS, path /system/xbin/busybox
Download
P.S. Install only on indicated above ROM versions, and it's obvious that you must have enough theory knowledge and practical experience to make use of 9008 patch, so I'm not responsible for any consequences, etc. Greets go to: CrashXXL (method inventor), Sabissimo (our former OP), and serg_gangubas (ROM guru).
==============================================================================================
31.07.2017 - Full ROM Patch for Bootloader Locked Moto X ATT/VZW/etc
Based on the same principle, and not depend on system partition content, so it suits any bootloader locked Moto X Gen1 ATT/VZW (possibly any model, besides 1049 RepW / 1055 US Cell), but takes about 4 hours to be done - prepare for that, 100% battery level only!
This full ROM patch includes:
SuperSU 2.82 Free
Xposed Framework v87 (installer, modules)
Busybox 1.26.2, path /system/xbin/busybox
ViperFX 2.5.0.5 - sorry needs polishing, removed now (
Gallery and Camera not depend on Moto services
Gboard instead AOSP Keyboard. If it eats too much RAM, see Simple Keyboard
GAPPSes updated. Use command like adb shell pm uninstall --user 0 com.blahblah.blah to block any unwanted app or service
ES File Explorer Free Edition (a clone, you can disable and install yours )
"Jedy" gesture
AdBlock support (effect lasts till the 1st reboot yet, I'll think about make it constant). Please, choose /data/hosts instead of /system/etc/hosts
ROM debloated, but not deodexed.
Download
Instruction
Be careful, phone will be WIPED then flashed in 9008 "brick" mode (CrashXXL idea). Before you start install Moto drivers, latest RSD Lite, and fully charge the battery.
1) Download and unpack zip on С: (or any), open Python27, launch RUN_path.bat (needs to be launched only single time), install driver QHSUSB_driver.exe, and launch file _Moto.X.BootLocked.*.exe (where * - is desired ROM).
2) Go into fastboot mode, execute RUN_blbroke.bat. Screen gets black, Device Manager in Windows finds "QHSUSB_DLOAD", and installs it as "Qualcomm HS-USB QDLoader 9008 (COM*)". If it doesn't install, google for Windows driver digital signature disable.
3) Now launch RUN_root.bat, and see that patching process took start.
4) A small patch *SPEAKERS.BOOST.exe (if exists) boosts both speakers' volume.
P.S. Please, don't flash anything extra into the phone. In case of trouble, all you need is inside this folder. Just make it work.
To make "Battery OK" in fastboot use fastboot_cyclecharge.bat
Completely drained out battery causing "USB input device" needs disassembly of the phone to charge externally.
In case Titanium Backup shows error "Batch backup interrupted: insufficient free storage space", delete default backup folder, and make a new:
Titanium Backup > Menu > Preferences > Backup folder location > Storage Provider > DocumentProvider storage > Show Internal Storage > Internal Storage > Select Internal Storage > Create the folder > Use the current folder. Done!
Notes for myself: Viper, force wipe, readme.txt, volume patch, Adblock, advanced debloat
Debloated, rooted, lightweight ROM - soon! )
PUBLISHED. Sorry, took long time.
As soon as I can actually get 5.1 flashed I'll try this.
Though I'm afraid I'll have to try to go to stock and use sunshine first, still have a locked BL.
But this is great, I didn't expect root so soon.
DownTheCross said:
As soon as I can actually get 5.1 flashed I'll try this.
Though I'm afraid I'll have to try to go to stock and use sunshine first, still have a locked BL.
But this is great, I didn't expect root so soon.
Click to expand...
Click to collapse
This method is working on locked BL.
DownTheCross said:
As soon as I can actually get 5.1 flashed I'll try this.
Though I'm afraid I'll have to try to go to stock and use sunshine first, still have a locked BL.
But this is great, I didn't expect root so soon.
Click to expand...
Click to collapse
Wait wait... If you can have now possibility to unlock bootloader - go for it immediately! You will have normal FULL root-rights (SuperSU 2.49). Don't install 5.1, if you plan to unlock, because Sunshine app (25$) works only on 4.4.2 Android.
This topic is to help those AT&T users that are boot locked forever (who missed out possibility to unlock on 4.4.2 by proceed to 5.1) to give them READ-ONLY root. Yes, it's limited, but anything at least.
s5610 said:
If you can have now possibility to unlock bootloader...
Click to expand...
Click to collapse
I guess anyone on 4.4.4 today. There is no possibility to use Sunshine anymore.
Anyway spasibo za method
Ahh, if I don't have to be BL unlocked that's great lol.
I haven't read too much into the 5.1 updates or sunshine for that matter.
I've been on krypton 1.4.1 since it was released, and I haven't been able to successfully upgrade to any 5.1 roms yet.
Works great!
Works great for me on Windows 10 RTM 64-bit! Thanks a ton, I was waiting for a post like this.
I only had 3 minor hiccups:
1. RSD Lite gave me an error about "getvar", so I had to go into flashfile.xml in the ROM zip and remove the line that said getvar
2. I had to reboot to disable driver signature enforcement twice for some reason because Windows Update
3. The run-root.bat got stuck on "Executing..." because I installed the wrong driver (the correct file is qcusb.inf when installed from device manager -> browse my computer for driver software -> let me pick from a list -> all devices -> have disk)
Otherwise, everything runs just as well as KitKat, including Xposed.
Hehe got to love step 9
System Write
How can we help in getting the system write to zero using the same method,because I have xt1058 model bootloader unlocked and I provide any file needed to disable the pesky system write...
How can we help in getting the system write to zero using the same method,because I have xt1058 model bootloader unlocked and I provide any file needed to disable the pesky system write...
Click to expand...
Click to collapse
First, never quote op. It takes way to much space and is redundant.
Second, to get write off we would need to some how either start a custom kernel some magical way or disable it via a kernel mod like htc guys did. Another way, which was done before was to burn the efuse but kernel has been patched since then.
Need some help, I did all steps until step 9. I installed the QHSUSB_DLOAD driver manually, and I can see 'Qualcomm HS-USB QDLoader 9008 (COM4)' showed in my Device Manager, but when I run 'RUN_Root.bat', I got this
c:\Python27>python qdloadRoot.py MPRG8960.bin -ptf root/partitions.txt
QDLoad utility version 1.2 (c) VBlack 2014
Found TTY port: com4
Sending MAGIC ...
QCOM fast download protocol targ:
Version: 7
Compatible version 2
Maximum block size 1024 (0x00000400)
Base address of Flash 0x00000000
Flash: eMMC
Window size: 30
Number of sectors: 128
First sector size: 2097152 (0x00200000)
Feature bits: 09
Sending SBL Reset...
Done
c:\Python27>pause
Press any key to continue . . .
Then I tried to run 'RUN_Root.bat' again, then I got
c:\Python27>python qdloadRoot.py MPRG8960.bin -ptf root/partitions.txt
QDLoad utility version 1.2 (c) VBlack 2014
Found TTY port: com4
Requesting Params...
Params:
Version: 8
Min version: 1
Max write size: 1536 (0x00000600)
Model: 144
Device size: Invalid or unrecognized Flash device, or Flash device progr
amming not supported by this implementation
Device type: Intel 28F400BX-TL or Intel 28F400BV-TL
Requesting SoftwareVersion...
Version: PBL_DloadVER2.0
Requesting SerialNumber...
Serial number: 00,00,48,03
Requesting HW Id...
HW Id: 00,00,48,03,e1,10,7e,00
Requesting PublicKey...
PublicKey: 39,c4,ee,3e,b5,be,eb,87,8e,2f,e3,b8,53,4d,14,6f,91,ca,fd,bb,94,2a,0d
,aa,d0,1e,b0,87,62,d4,b9,b8
Uploading file 'MPRG8960.bin' to addr 0x2a000000...
Executing...
Could not find Qualcomm device in Emergency download mode
Done, with errors!!!
c:\Python27>pause
Press any key to continue . . .
any suggestions? Thanks
jahrule said:
First, never quote op. It takes way to much space and is redundant.
Second, to get write off we would need to some how either start a custom kernel some magical way or disable it via a kernel mod like htc guys did. Another way, which was done before was to burn the efuse but kernel has been patched since then.
Click to expand...
Click to collapse
Ill put the files here
Fantastic!!! I was looking this. All the last week I was sleeping about 3 hours per day trying to root my phone.
----
I scream "Victory" before the process finish.
Damn! My phone reboot and stay in the android doll fallen screen.
DejanPet said:
Ill put the files here
Click to expand...
Click to collapse
What to do with these files?
Those files are needed by Jahrule
Sabissimo
Hello.
I did everything as instructed, but eventually got the screen "no command".
The only thing I did not flash rom - a month ago updated by an OTA to 5.1, thought it was not necessary.
Factory reset does not help.
Advise something.
In the end, everything worked, thank you))
It works
It works great! Thank you very much! ATT xt1058.
eze_cba17 said:
Damn! My phone reboot and stay in the android doll fallen screen.
Click to expand...
Click to collapse
Follow the OP instruction EXACTLY, no exceptions!
If you got your current 5.1 through AT&T OTA, it's not enough for root patching procedure. A full RSD 5.1 official SBF flash over is required.
Could someone please do a video on this. I'm having a little trouble.
Hi all xda users
We previously released v1.0.0 version of this tool on this topic, And many users were demanding to make a new version of the tool
Today we release new version of our software gsd android tool v1.0.1 with new ui and more ability , You can follow the Tools capabilities with this Topic
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Gsd android tool is a tool for Android phone service
The unique features of this tool will definitely attract your attention
Click to expand...
Click to collapse
Impact Tools features
Part of samsung > Unlock This option is called Samsung, but you can also use it for other Brand.
1 - scan and full information In Selected Mode
2 - Reset Frp Adb Mode
3 - Reset Frp dial Mode
4 - Bypass All Screen Lock In Frp = On Or of and Oem = on Or Of encrypted data partition and uncrypted Need Flash Eng-root
5 - Bypass All Screen Lock In Adb Mode = need Root Access
6 - Bypass All Screen Lock In Twrp Mode = No need Root and More ...
7 - Bypass All Screen Lock In sideload Mode = Custom Recovery Data Modification Method
8 - Bypass All Screen Lock In Sildeload Mode = Custom Recovery Need (encrypted data Partition)
9 - Important Make RvSecuRity use Boot.img for Unlock = No need Root Or any Think Just Need Boot.img
What is RvSecuRitY?
We succeeded in 2014 by modifying the kernel, unlocking the Android device without clearing the data
Then we began mass production of these kernels for each Android device We put the names of these kernels "RvSecuRitY" (Remove Security)
We added the button for making these kernels to this software. you can drop boot.img to input section and get remove screen lock kernel very easy And write it by flasher(Odin , Spflashtool, and more ... ) on the device
This tool unlock all encrypted data partition w/o data loss
This method no need to twrp or root , you just need orginal boot.img (that you can extract from orginal firmware)
Click to expand...
Click to collapse
samsung > Android Part You can use some of the options for this brand for other brands.
1 - Read Full Information
2 - exit Safe And Factory Mode = Need Root Access
3 - Full Format Device = Need Root Access
4 - enable Multi Language Samsung = Need Root access
5 - ٍٍEnable Call recording (The main functionality hidden in Samsung.)= Need Root access
6 - Enable Blacklist (The main functionality hidden in Samsung.) = need root Access
7 - ٍEnable Hardware Version In About Phone(The main functionality hidden in Samsung.) = Need Root Access
8 - disable update System Notification = Need Root access
9 - disable Anti-Malware Application Samsung = need Root Access
10 - Enable Camera Shutter (The main functionality hidden in Samsung.)
11 - reboot Device In Normal , download , recovery , Bootloader Mode
12 - Write File (flash) In sideload Mode
13 - Important Read (backup) automatically boot , cache , efs , hidden , param , recovery , system partition = dd backup in Adb Mode Need Root Access
14 - Important Restore (backup) automatically boot , cache , efs , hidden , param , recovery , system partition = dd backup restore in Adb Mode Need Root Access
Click to expand...
Click to collapse
Other Brands > Main Menu
1 - Read Full Information on Device = Adb Mode
2 - Read Package Name System and Non=system Applocation = adb mode
3 - Bypass all Screen Lock = Need Adb and Root Access
4 - Full Format Device = adb Mode Need Root Access
5 - Enable Multi Language Htc Devices = adb Mode Need Root Access
6 - Important Get Length and Begin Address For Reset Frp Mediatek Devices (you can unlock Frp by using Length and Begin Address)
7 - Backup Nvrm Mediatek Device = adb mode Need Root Access
8 - write Nvrm Mediatek Backup = adb Mode Need Root Accesss
9 - Important
10 - adb Reboot Device To Edl mode , recovery , Fastboot , Normal Mode
11 - Find Country Device Use imei Phone
Click to expand...
Click to collapse
Other Brand > Fastboot Part
1 - Read Full Information Device !
2 - Read Full Information Hisilicon Devices Emmc
3 - Frp Reset = Need Bootloader Unlocked
4 - Full Format Device = Need Bootloader Unlock
5 - Relock Bootloader Unlocked
6 - Erase Partition Menu (Erase Boot , Recovery ,System , Data ,cache Partition)
7 - unlock Bootloader menu (Unlock Bootloader Use Code Sony , Huawei and more ... and Unlock Bootloader Htc Device Use Unlock.bin)
8 - reboot fastboot in edl mode , bootloader , RUU , Normal Mode
9 - Flash Single File + Erase (Flash boot , recovery , system , splash , radio , data )
10 - advanced Menu Flasher (Flash Multi file zip File , Boot , Recovery , Recovery2 , system , data , splash , radio , Modem , Cache , cust , Fastboot , Nvme files)
11 - Nokia X , Xl , X+ Flasher Menu (system , boot , recovery , variant , data , cache , Preload)
Click to expand...
Click to collapse
Important Developer Tools > System.img Tools
1 - Read Full Information System.img File
2 - Unpack any System.img 2.3 to 7.x
3 - Repack System Folder 2.3 to 7.x
4 - Convert Sparse Header System.img To 32
5 - Make System.img Flashable In flashers On You Device (Need Root Access)
Click to expand...
Click to collapse
Important Developer Tools > kernel Tools
1 - Unpack Recovery , Boot.img
2 - Repack Unpacked Kernel
3 - Convert File_Contexts.bin To File_Contexts For Repack system Extracted Folder
4 - Important Make RvSecurity Kernel For Bypass All Code = Need Boot.img
5 - Make adb Enabler Kernel = need boot.img
6 - Important make Pre-root Kernel (Chainfire Instructions) = need Boot.img
7 - Make Dm-verity Error Fixer = need Boot.img
Click to expand...
Click to collapse
End of capability definition
To help you use this tool , We added a "Tooltip" for guidance , You can move your mouse over the button and see the functionality of the button.
If I had an empty time. In the future, I will try to get the full tutorial on how to use this tool in the next section
If you have any problems, please report this topic . This tool is portable Version No Need Install
Prerequisite for using this software:
NetFramework3.5
download links :
Gsd_Android_Tool_V1.0.1_Release_Portable
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
enjoy.:highfive:
asgharSo said:
Hi all xda users
We previously released v1.0.0 version of this tool on this topic, And many users were demanding to make a new version of the tool
Today we release new version of our software gsd android tool v1.0.1 with new ui and more ability , You can follow the Tools capabilities with this Topic
Impact Tools features
Part of samsung > Unlock This option is called Samsung, but you can also use it for other Brand.
samsung > Android Part You can use some of the options for this brand for other brands.
Other Brands > Main Menu
Other Brand > Fastboot Part
Important Developer Tools > System.img Tools
Important Developer Tools > kernel Tools
End of capability definition
To help you use this tool , We added a "Tooltip" for guidance , You can move your mouse over the button and see the functionality of the button.:angel:
If I had an empty time. In the future, I will try to get the full tutorial on how to use this tool in the next section
If you have any problems, please report this topic . This tool is portable Version No Need Install
Prerequisite for using this software:
NetFramework3.5
ِDonate Me
download links :
Gsd Android Tool V1.0.1 Release Download - Mediafire Link
Gsd Android Tool V1.0.1 Release Download - gsm-developers Link
Gsd Android Tool V1.0.1 Release Download - 4Shared Link
enjoy.:highfive:
Click to expand...
Click to collapse
thank you so much for the good tools ??
9jarom said:
it's a Great Tool but nothing new
...only if it can remove Samsung frp 7.0 in download mode or switch from MTP to ADB
Click to expand...
Click to collapse
hi dear
This tool has better functionality
unlock s6,s7,s8 one5 ,not5 and more without losing data in the case of frp = on and oem = on
And there are dozens of other features that are not included in any of the free tools.
thanks
problemathic said:
downloaded it but cant use it. just having the tool is only loading. why?
Click to expand...
Click to collapse
if solutions not work for you,use this tool
Replace this tool on gsd android tool.exe
Code:
http://www.mediafire.com/file/tn8x4s4ecen5cew/Gsd%20Android%20Tool.zip
Very Well Crafted....Kudos!
Having tinkered with well over a dozen similar tools over the past couple of years....I can only say.....Kudos to all involved in this project! It is very well crafted indeed and covers a very respectable gamut of tools while managing to be quite expeditious throughout the process. Most importantly...it works like a Swiss watch....precisely and reliably. Are there other things it could do?...Well...that's like asking a muscle car owner if there are any other bolt-ons his car could accomodate....right?
Again...Awesome Job!!...but a wise man once told me...when you start to break ahead of the pack...that's when you need to run twice as fast....
asgharSo said:
Hi all xda users
We previously released v1.0.0 version of this tool on this topic, And many users were demanding to make a new version of the tool
Today we release new version of our software gsd android tool v1.0.1 with new ui and more ability , You can follow the Tools capabilities with this Topic
Impact Tools features
Part of samsung > Unlock This option is called Samsung, but you can also use it for other Brand.
samsung > Android Part You can use some of the options for this brand for other brands.
Other Brands > Main Menu
Other Brand > Fastboot Part
Important Developer Tools > System.img Tools
Important Developer Tools > kernel Tools
End of capability definition
To help you use this tool , We added a "Tooltip" for guidance , You can move your mouse over the button and see the functionality of the button.:angel:
If I had an empty time. In the future, I will try to get the full tutorial on how to use this tool in the next section
If you have any problems, please report this topic . This tool is portable Version No Need Install
Prerequisite for using this software:
NetFramework3.5
ِDonate Me
download links :
Gsd Android Tool V1.0.1 Release Download - gsm-developers Link
Gsd Android Tool V1.0.1 Release Download - 4Shared Link
enjoy.:highfive:
Click to expand...
Click to collapse
the greatest free and paid tools for samsung i had seen ever!!!
a great thanks to you brother:good::laugh:
Open Source
is this available on github?
nice work btw
VirtualBornSkiller said:
is this available on github?
nice work btw
Click to expand...
Click to collapse
No sir, This is not open source
good luck
Thnks much.....
where should i flash the revsecurity file in odin ?
in ap or bl ?
salamkonaziz said:
where should i flash the revsecurity file in odin ?
in ap or bl ?
Click to expand...
Click to collapse
No difference
But it's better to put it in ap.
asgharSo said:
No difference
But it's better to put it in ap.
Click to expand...
Click to collapse
Why always AP?? oh well, Im not complaining. Listen, thank you guys for making such a great tool and sharing it!!! Blow away! May innovation be like a sister to you and yours. Question though.... so basically I can flash and tweak phones with what chip support? I missed it. Qualcomm (obviously because of Samsung) but MediaTek too? Also, how difficult would it be to port this to a Linux OS, if I used something like CrossOver or Wine or similar?
-Bad Rx__
BadRx said:
Why always AP?? oh well, Im not complaining. Listen, thank you guys for making such a great tool and sharing it!!! Blow away! May innovation be like a sister to you and yours. Question though.... so basically I can flash and tweak phones with what chip support? I missed it. Qualcomm (obviously because of Samsung) but MediaTek too? Also, how difficult would it be to port this to a Linux OS, if I used something like CrossOver or Wine or similar?
-Bad Rx__
Click to expand...
Click to collapse
Hi dear
If you put the file in bl, it will be writed
Odin software write it to the device based on the kernel name or file system in the tar file.So it's not important to put in either ap or in bl
You can use this method for any processor or brand.Only your device must accept custom binary.(boot.img RvSecurity)
For the Linux version, I try to write the next version
thanks and good luck
Gsd Android Tool Open Error
Gsd Android Tool Open Error How to Solve
這是一個很棒的工具
我見過的三星最好的免費和付費工具!!!
Well first things first.. i have no idea for what are 90% of options there BUT i somehow know it is CORE app now to unlock galaxy s7 edge.. but now the part where i need to ask anybody to lead me step by step (TOTALLY) how can i (and if i can) install custom recovery using this tool? Problem with my device is my volume buttons are totally non functional this is why i never was able to switch from Odin mode to recovery instantly by buttons combination (in result - always locked device and had to flash stock rom). I am on Stock Android 8.0 for S7 Edge G935F. Sorry for typing like a noob (a actually rooted/unlocked a lot of devices sometimes spending a lot of time on it but without volume buttons I am in dead point) PS. Last time i had to make 300kOhm device to get my phone into download mode so I am able to get into download but i am not able to use volume keys. And again thanks for any tips/tutorials etc
MavericzeK said:
Well first things first.. i have no idea for what are 90% of options there BUT i somehow know it is CORE app now to unlock galaxy s7 edge.. but now the part where i need to ask anybody to lead me step by step (TOTALLY) how can i (and if i can) install custom recovery using this tool? Problem with my device is my volume buttons are totally non functional this is why i never was able to switch from Odin mode to recovery instantly by buttons combination (in result - always locked device and had to flash stock rom). I am on Stock Android 8.0 for S7 Edge G935F. Sorry for typing like a noob (a actually rooted/unlocked a lot of devices sometimes spending a lot of time on it but without volume buttons I am in dead point) PS. Last time i had to make 300kOhm device to get my phone into download mode so I am able to get into download but i am not able to use volume keys. And again thanks for any tips/tutorials etc
Click to expand...
Click to collapse
DId you get this done? Im in same situation except i have the Samsung S7 GM 930W8
legendzj said:
DId you get this done? Im in same situation except i have the Samsung S7 GM 930W8
Click to expand...
Click to collapse
Well for me worked out flashing TWRP(in twrp turn off auto reboot) and i was able to turn off phone by myself by unplugging the battery (yea unplug when in download mode after flashing TWRP then flash back into download mode (i used USB JIG made by myself) and then through twrp i flashed eng-root with autoreboot and it flashed directly to the twrp BUT i dont know if this will work also for you keep that in mind
MavericzeK said:
Well first things first.. i have no idea for what are 90% of options there BUT i somehow know it is CORE app now to unlock galaxy s7 edge.. but now the part where i need to ask anybody to lead me step by step (TOTALLY) how can i (and if i can) install custom recovery using this tool? Problem with my device is my volume buttons are totally non functional this is why i never was able to switch from Odin mode to recovery instantly by buttons combination (in result - always locked device and had to flash stock rom). I am on Stock Android 8.0 for S7 Edge G935F. Sorry for typing like a noob (a actually rooted/unlocked a lot of devices sometimes spending a lot of time on it but without volume buttons I am in dead point) PS. Last time i had to make 300kOhm device to get my phone into download mode so I am able to get into download but i am not able to use volume keys. And again thanks for any tips/tutorials etc
Click to expand...
Click to collapse
first write eng-root then bypass use this tool
i'm developing new version of Gsd android Tool
we add many Option For bypassing Screen Lock (android 7,8__)
Screen Shot Of new version :
https://twitter.com/ILYA20_GSD/status/1054027375816724481
Cooming Soon ... !
asgharSo said:
first write eng-root then bypass use this tool
i'm developing new version of Gsd android Tool
we add many Option For bypassing Screen Lock (android 7,8__)
Screen Shot Of new version :
https://twitter.com/ILYA20_GSD/status/1054027375816724481
Cooming Soon ... !
Click to expand...
Click to collapse
Haha thanks for respond anyway I managed to get it working then but for now my S7 Edge is dead (screen flickering after drop). Thanks for respond and tutorial for others anyway! Have a nice day
RECOVERY information:
Name Version: Xiaomi Mi 8 Lite Special Edition TWRP with modified optimizations
package name: TWRP-3.2.3-XIAOMI8LITE- CN-wzsx150-fastboot.7z
build time: 2018.10.03
applicable models: Mi 8 Lite
the compiler author: wzsx150
micro-blog account: wzsx150
team name: LR.Team
The optimizations/changes:
* Delete redundant languages, keep English, add Chinese language, default Chinese.
* Modify the default configuration, for example, the default time zone is East Eight Zone, default screen brightness, default vibration, default 24 hours, default return button on the right, default Chinese and so on.
* Modify the default configuration file path to reduce the possibility of conflicts with other people's compiled versions.
* Adjust and optimize the Chinese text and description, and re-edit all the items one by one, which is more accurate, understandable and humanized. Also added display mtp enable off display, file operation result display, operation page title display, permission description when modifying permissions, etc. UI text display.
* Modify the unlocking interface and adjust the height of the sliding unlocking bar, which can effectively prevent misoperation (the original unlocking bar and the operating unlocking bar are of the same height. When the unlocking is completed, the sliding may be repeated, and the corresponding action is directly operated).
* Open more partition backup and restore, such as modern baseband partition, bootloader, persist, cust and other partitions, easy to backup the underlying files before brushing, can restore the underlying files after brushing.
* Add .bin and .mbn format image files, so you don't need a zip brush package, you can write the underlying file. The original version only supports the brushing of .img format image files. (Be sure to pay attention to the selected partition!!!!)
* Solve the problem of interface jam when using the simulation operation (the simulation operation is mainly for testing the theme, and no actual operation).
* Add the manual installation root function in Advanced Options > root system. Add a display root system option on this basis for manual operation.
* Added the ability to unenforce encryption, in advanced options > Unforce Encryption. You can remove the official system to force encryption and cancel the check.
* Change the built-in root mode and add magisk as the default root mode.
* Fixed button and button operations for some interfaces.
* The adb/usb debug mode is enabled by default, which is convenient for operating the phone through the computer command line in rec mode.
* MTP is enabled by default. In the rec state, you can also connect your phone to your computer to facilitate file copying.
* Modify the logo interface, modify the header of the main interface page, and add the display phone model and team name, author name.
* Fix some logical relationships and modify some interface displays.
* Added remove root function
* Added remove power-on password function
* Added remove battery information function
* Added signature boot function, requires system to have complete system, mainly to prevent official rec cover twrp
* Increase recovery of official rec function, conditions are very demanding, must The official original system and boot, otherwise it can not be successfully executed
Download:
TWRP Zip
TWRP IMG
How to install:
TWRP Zip can be flashed from other TWRP Versions
Fastboot just run .bat file to install it from fastboot mode
TWRP.img can be flashed manually from fastboot
all credits goes to @wzsx150, he built this TWRP
Source
Just in case
Thanks dev!!!
so is this english or chinese? screenshot shows chinese?
HyunJoon said:
so is this english or chinese? screenshot shows chinese?
Click to expand...
Click to collapse
it has English & Chinese only, change it from settings
Hope to see other languages too. For me chinese is useless, for example. You could make 2 versions: one with all languages and another with this 2 chosen by you.
HTCDevil said:
Hope to see other languages too. For me chinese is useless, for example. You could make 2 versions: one with all languages and another with this 2 chosen by you.
Click to expand...
Click to collapse
i didnt make this TWRP, read OP again, and you can use English its still included
AL_IRAQI said:
i didnt make this TWRP, read OP again, and you can use English its still included
Click to expand...
Click to collapse
Ok, no problem for me about using english, i just didn't understand the choice of developer.
HTCDevil said:
Ok, no problem for me about using english, i just didn't understand the choice of developer.
Click to expand...
Click to collapse
this TWRP build was released for Chinese users, so it kinda makes sense to remove all Languages, and only 2 or Chinese only
AL_IRAQI said:
this TWRP build was released for Chinese users, so it kinda makes sense to remove all Languages, and only 2 or Chinese only
Click to expand...
Click to collapse
Points of view, i don't think so
Is this for the Chinese variant only, or it's also for the global version?
ramping said:
Is this for the Chinese variant only, or it's also for the global version?
Click to expand...
Click to collapse
it should work for both
sorry to hijack this thread, but it's the only thread I found about Mi8 Lite, does this phone support treble? Has anyone tried to flash a GSI? If yes what are the bugs? Thanks.
HTCDevil said:
Points of view, i don't think so
Click to expand...
Click to collapse
You can always process it yourself, removing the languages you don't like and adding more
guglicap said:
sorry to hijack this thread, but it's the only thread I found about Mi8 Lite, does this phone support treble? Has anyone tried to flash a GSI? If yes what are the bugs? Thanks.
Click to expand...
Click to collapse
It does support treble, but i never tried to flash it, cuz i dont even own that device
Thank you!!
hello sorry for my bab english , i have xioami mi 8 lite, i want unlock the bootloader and install twpr and then install rom Spanish i have the version china. somebudy tellme?
Thanks for share your work, Is there a list of avaiable rom for Mi 8 light? I do not find nothing...
Anyone know a stabile Google camera?
I'd also like to know if there is a list of ROM for the MI 8 Lite.
If anyone tried a Treble GSI ROM with this recovery.
And if anyone has found a working Gcam. Thanks!!
Has anyone tried this TWRP already? Does it all work or are there limitations?
********** ANNOUNCEMENT - Beta Enrollment without Banner (OPEN NOW - Nov 16,17) - Read More Here
INTRODUCTION - Hello all. Now Samsung wants us to go to Members app and keep looking for banner to sign up for Android 11, One UI 3 Beta . It went live October 27th, 10:20 PM EST, As fate would have it, i went to sleep early, i missed it and the banner refused to show up for me in the morning. Download was only showing up for people with unlocked variants on ATID firmware.
DISCLAIMER / NOTICE - Flashing is always risky. I am not responsible for anything that may happen to your device including but not limited to it turning against you, making you its slave and sucking you into the Matrix.
This post is a collection of wisdom, research and hard work of many people over many years across many forums and not just XDA. I will try to credit and link to their original posts.
TIP -Keep in Notice -This SHALL NOT Factory Reset Your Device or Format Data, it is still a good idea to Take Back Up - Just a Suggestion - Always have a latest Back Up
******** UPDATE - It seems ATT devices are getting wiped now if its CSC or the Sim remains to be tested.
i don't have ATT hence cant verify but in case you have an Unlocked device (N986U1) with ATT sim, then, removing sim and Changing the CSC to XAA/XAA/XAA before sideloading Beta is advisable.
PROBLEM STATEMENT - Missed the One UI 3.0, Android 11, Beta Sign up Banner in Members app or got the banner but didn't get the download and I really want it NOW.
Not sure if you want it now? - Find the BETA CHANGELOG HERE
GRAB YOURSELF A COFFEE / DRINK, because depending on where you at and how fast you/your internet speeds/your Machine is this may take anywhere between 7 to 45 MinsSOLUTION -
1. Pre-Requisites - Make sure Following Conditions are met before you start
You need a PC/Laptop along with your phone and USB Cable.
You need ADB installed, you can use ADB on Linux too - NOTE If your ADB Tools are not working, download my ADB Folder called platform-tools. Then extract it somewhere easy to remember/ find, like desktop
Remember the Location of the folder where you have ADB installed / Location of platform-tools- This is the location containing adb.exe file.
You may or may not need ADB/USB Drivers if any errors in ADB please Download Drivers from here and Install on your PC.
This following one step is relevant Only for flashing Beta 1
Use Odin to Flash Unlocked (SM-N986U1) ATID Firmware if you are not on that. Refer this thread to get your Firmware.
For changing Firmware from N986U to N986U1 and / or GUIDE TO FLASHING USING ODIN Refer This thread
______________________________________________________________________________________________________________________________________________________________
2. Now Download the relevant Beta File that you intend to flash - note that to Sideload Beta 2 you need to be on Beta 1 first. Mandotory Sequence = Beta 1>>Beta 2>>Beta 3 There is no skipping versions possible here.
BETA 1 (ZTGJ) Get the Beta1.zip file from here Thanks to @thatotherguy.. for the original zip.
BETA 2 (ZTK1) Get the Beta2.zip file from here
BETA 3 (ZTK9) Get the Beta3.zip file from here
______________________________________________________________________________________________________________________________________________________________
*************** Apply Update from SD card failed for me (Feel free to try that ) but here we will be using ADB Sideload Feature in Stock Recovery*************
HOW TO - Using ADB Sideload - Windows -The Process is Similar for Linux too
1. Copy the downloaded zip file to the ADB Folder (From Pre-Requisite step). ADB Folder is the folder containing ADB.exe it might be named differently for you (The one i have posted is called platform-tools)
2. Open Command Prompt Window as Admin.
3. Type in
Code:
cd Copy-paste the location of your ADB folder here
4. Connect the phone to the PC using USB Cable and Unlock it. Go to Developer Options and Switch on USB Debugging.
To turn on developer options go to Settings>>About Phone>>Software Information>> Then tap the build number 7 times - Developer options will appear at the bottom of Settings Menu
5. On your PC Type in Command Prompt
Code:
adb devices
6. Give Permission that appears on your phone and PC - I check the box Always Allow, you should do the same.
7. Now type the following and the phone will reboot to recovery.
Code:
adb reboot recovery
8. Once you see recovery on your phone Use Volume Keys to scroll down to Apply Update from ADB and press Power Button.
9. Now on your PC, Type the following in Command Prompt; this is just to be sure, it should show the device name with Sideload next to it.
Code:
adb devices
10. Type
Code:
adb sideload Beta1.zip
For Beta 2 use adb sideload beta2.zip Similarly For Beta 3 use adb sideload beta3.zip. Use whatever you have named the zip file. Most people use update.zip. The commands here are for the attached files in this post and their naming convention.
11. Wait for it to finish and Done
2nd (Second) BETA Is Out- How To Do this if you are not able to Enroll for Beta and or don't see update to download even after Enrolling
Second Beta should be flashed After Beta 1. Second Beta (ZTK1) can not be flashed unless you have Beta 1 (ZTJG).
To flash follow the same instructions as above only this time the prerequisite is you have to be on the 1st Beta. Download the 2nd Beta (ZTK1) Zip File to flash Here Thanks to @hayabusa1300cc for the FOTA Link.
3rd (Third) BETA Is Out- Nov 16, 2020 Do this if you are not able to Enroll for Beta and or don't see update to download even after Enrolling
Third Beta should be flashed After Beta 1>>Beta 2. Third Beta (ZTK9) can not be flashed unless you have Second Beta (ZTK1). Second Beta (ZTK1) can not be flashed unless you have Beta 1 (ZTJG).
To flash follow the same instructions as above only this time the prerequisite is you have to be on the 2nd Beta. Download the 3rd Beta (ZTK9) Zip File to flash Here
OPTIONAL THINGS TO DO POST UPDATE
If you want to enable RCS (In the Native SMS app) and Native Video calling (This feature is on Tmobile) have a look at this thread.
Check out this Guide Service Mode and CSC Guide/Enable LTE/5G Bands and Services/5G Low Band on U1 by @mellojosh
TROUBLESHOOTINGSome people might run into "cant read update.zip" error for that we need to make ADB Large address aware. Follow the Steps Here I use the Advanced mode as it shows the true false flags. - This wont happen if you use the ADB Tools provided by me above under the Pre-requisites section.
************** FOR FUTURE BETA OTA Questions / Bugs - Observations and some more info - Go Here ********Please dont ask questions without reading.
QUESTIONS, HELP & SUPPORT ?? - See if I am Online here on this Live Chat
If it helped HIT THAT THANKS BUTTON, what are you waiting for ? Cheers !!
Suggest you rename the title for which device it's for as it's not for every snapdragon (right?)
I get "adb: failed to read command: No error"
ekerbuddyeker said:
Suggest you rename the title for which device it's for as it's not for every snapdragon (right?)
Click to expand...
Click to collapse
I flashed on an Unlocked one so there is no way for me to tell if this can be flashed on N986U since so many people have flashed Unlocked firmware on the U devices using Odin (One confirmed guy flashed unlocked firmware on Verizon locked device and got the Beta banner) hence i think this will work for all Snapdragon devices. Give it a try and see. Just that before you try this make sure you are on ATID firmware.
d_ganggreen said:
I get "adb: failed to read command: No error"
Click to expand...
Click to collapse
Use a different USB Cable. A good quality one preferably. Also try changing USB port.
Can i install this on sm n 9860 version and does google pay and samsung pay beta work?
warriorvibhu said:
Use a different USB Cable. A good quality one preferably. Also try changing USB port.
Click to expand...
Click to collapse
Hmm, still getting same. Tried 3 cables including the one that came with the phone and both usb ports on my computer.
d_ganggreen said:
Hmm, still getting same. Tried 3 cables including the one that came with the phone and both usb ports on my computer.
Click to expand...
Click to collapse
Are you on ATID Firmware?
warriorvibhu said:
Are you on ATID Firmware?
Click to expand...
Click to collapse
I am, I odin flashed it a few weeks ago.
1gorelo said:
Can i install this on sm n 9860 version and does google pay and samsung pay beta work?
Click to expand...
Click to collapse
Too early in the morning to go out and test that. This is Beta and i have already encountered some bugs. So you have to be up for that.
Good Lock wont work, gesture navigation is buggy, you can not even apply wallpapers from the Galaxy Themes app.
Wallpaper Service on the other hand is greatly improved. Fingerprint sensor is much faster.
d_ganggreen said:
I am, I odin flashed it a few weeks ago.
Click to expand...
Click to collapse
My friend there are so many reasons why that error can happen. Sometimes you might have to change the ADB version. I am attaching the platform-tools i used. Extract this zip inside folder on desktop and try. If that doesnt work you might need to update ADb/Samsung drivers. Let us know if this works.
warriorvibhu said:
My friend there are so many reasons why that error can happen. Sometimes you might have to change the ADB version. I am attaching the platform-tools i used. Extract this zip inside folder on desktop and try. If that doesnt work you might need to update ADb/Samsung drivers. Let us know if this works.
Click to expand...
Click to collapse
Thank you! Whatever it was, that worked. I am able to get it running with your tools. I am running it now.
CHANGELOG - Android 11_OneUI 3 Beta
************ Notice: This changelog is compiled from various different resources online, verification of these features rests with the users **********
Code:
[COLOR="SeaGreen"][CENTER]BETA CHANGELOG[/CENTER][/COLOR]
[B]Home screen[/B]
– Touch and hold an app to add an associated widget
– Turn the screen off by double-tapping on an empty are of the Home screen. You can turn this on in Settings > Advanced features > Motion and gestures.
Lock screen
– Dynamic Lock screen now has more categories, and you can select more than one.
– Lock screen widgets are improved.
[B]Contacts, Phone and Call Background[/B]
– Added the ability to edit multiple linked contacts at one time.
– Added an option to help you quickly delete duplicate contacts.
– Enhanced the search experience.
– Extended the storage period of the Trash bin from 15 to 30 days.
– Added the ability to customize the call screen with your own pictures and videos.
[B]Messages[/B]
– Created a Trash bin to store recently deleted messages.
– Call & Text on other devices
– Added the ability to turn Call & text on other devices on or off with Bixby Routines.
[B]Calendar[/B]
– Events with the same start time are now shown together in month and agenda view.
– Reorganized options for adding and editing events.
– Improved layout for full screen alerts.
[B]Reminder[/B]
– Improved layout for full screen alerts
[B]Camera[/B]
– Improved auto-focus and auto exposure functionality and usability.
– Improved stabilization when taking pictures of the moon at high zoom levels.
[B]Photo editor[/B]
– Added the ability to revert edited pictures back to their original versions.
[B]Bixby Routine[/B]
– Grouped preset routines help you get started quickly and learn how to build your own routines easily.
– You can now see what actions are reversed when a routine ends.
– New conditions have been added, such as a specific start time, the disconnection of a Bluetooth device or Wi-Fi network, a call from a specific number, and more.
– New actions have been added, including talking to Bixby and accessibility actions.
– You can add a customized icon for each routine and add routines to the Lock screen for quick access.
[B]Digital wellbeing and Parental controls[/B]
– Added trends to your weekly report. You can see how your usage has changed since the previous week and check your usage time for each feature.
– Added phone usage time while driving to the weekly report.
– Added a lock screen widget so you can check your screen time without unlocking your phone.
– Added separate profiles for personal and work modes so you can track your screen time separately.
[B]Internet[/B]
– Added ability to block websites from redirecting you when you tap the Back button.
– Added warnings and blocking options for websites that shot too many pop-ups or notifications.
– Rearranged menus to make things easier to find.
– Added several new add-ons, including one that translates websites.
– Added option hide the status bar for a more immersive browsing experience.
– Increased maximum number of open tabs to 99.
– Added ability to lock and reorder tabs.
– Improved design for tab bar which is now supported on all devices.
– Ended support for Samsung Internet edge panel.
[B]Quick panel[/B]
– See your conversations and media more conveniently in their own sections when you swipe down from the top of the screen.
[B]AOD[/B]
– Always On Display widgets are improved.
[B]Accessibility[/B]
– Get quick access to the most important accessibility settings during device setup.
– Get recommended accessibility features based on what you use.
– Set the Accessibility shortcut more easily in settings.
– Sound detectors now work with your SmartThings devices such as TVs and lights to give you more visible alerts when the doorbell rings or a baby is crying.
[B]Samsung Keyboard[/B]
– You can find the keyboard in settings more easily under General management in Settings, and the settings have been reorganized to put the most important ones first.
Samsung DeX
– You can now connect to supported TVs wirelessly.
– New touchpad multi-gestures let you change screen zoom and font size more easily.
Feel free to add anything else that you observe.
warriorvibhu said:
Wohooo Fingers Crossed. Did it finish ?
Click to expand...
Click to collapse
Yes it did, running 3.0 beta now!
warriorvibhu said:
I flashed on an Unlocked one so there is no way for me to tell if this can be flashed on N986U since so many people have flashed Unlocked firmware on the U devices using Odin (One confirmed guy flashed unlocked firmware on Verizon locked device and got the Beta banner) hence i think this will work for all Snapdragon devices. Give it a try and see. Just that before you try this make sure you are on ATID firmware.
Click to expand...
Click to collapse
I'm on n9860 which is a snapdragon. I'm not sure if it's the same. Anyone want to try?
My US unlocked stuck at 16% when sideloading? Is it normal?
jianansong said:
My US unlocked stuck at 16% when sideloading? Is it normal?
Click to expand...
Click to collapse
Since how long ?
Which step are you at?
warriorvibhu said:
Since how long ?
Which step are you at? (See Pics)
Click to expand...
Click to collapse
On my phone, it shows "Verifying updte package..."
On the adb, it shows serving update.zip 16%.
It has been there for at least 20 minutes... Do I need to cancel and restart?
I used the uploaded adb and the first link for update.zip.
jianansong said:
On my phone, it shows "Verifying updte package..."
On the adb, it shows serving update.zip 16%.
It has been there for at least 20 minutes... Do I need to cancel and restart?
I used the uploaded adb and the first link for update.zip.
Click to expand...
Click to collapse
Yes thats too long Cancel and restart, It took me 97.5 seconds to verify the package.
Your ADB is fine dont change that. For firmware you can try using the second link from google drive. do you meet the criteria Unlocked and on ATID ?
warriorvibhu said:
Yes thats too long. do you meet the criteria Unlocked and on ATID ?
Click to expand...
Click to collapse
Yes, mine is us unlocked and it's on ATID. Do you know how I could cancel it?
---------- Post added at 03:45 PM ---------- Previous post was at 03:43 PM ----------
jianansong said:
Yes, mine is us unlocked and it's on ATID. Do you know how I could cancel it?
Click to expand...
Click to collapse
At the command line, I clicked "control + C" and surprisingly the progress number starts moving again, and now I am at 53% and it's still going...