Help - battery ran out and has corrupted apps / OS? - Zuk Z1 Q&A, Help & Troubleshooting

Hi,
With a battery capacity of 2% I decided to carry on and listen to one more Blink 182 song, then it died halfway through. Put the phone on charge and now stuck in endless reboot loops. Normally the reboot happens during the Cyanogen splash screen, sometimes it makes it past there to an "Optimising Apps" window where it will optimise all apps, but then as soon as it says "Starting apps" it reboots.
I was on stock OS. I have had something similar happen before - always when the battery has died. Previously using the Zuk Z1 toolkit fastboot commands seems to have worked (although I'm not sure if it has ever actually reflashed it as fastboot doesn't appear to work now).
I have tried using fastboot to reflash (stock OS, later ones) - fastboot flash doesn't seem to work (device locked). Using ADB sideload I can reflash (YOG4PAS3AJ, YOG4PAS7DF, YOG4PAS9IG) , but the same ting happens - it seems when the apps are compiled and run it reboots.
All I care about is my photos and videos of my kids - have given up on the phone now (living with a broken home button is frustrating enough).
Can anyone suggest anything? If I could boot the phone up into some sort of safe mode where the apps don't run maybe it would help, but maybe there is no "safe mode" in CM 12.1? Any suggestions would be greatly appreciated.
Thanks

can you boot into bootloader/fastboot menu etc? being there connect phone to laptop/computer & see if pc shows you the phone drive so that you can copy data for now?

RZukZ1 said:
Hi,
With a battery capacity of 2% I decided to carry on and listen to one more Blink 182 song, then it died halfway through. Put the phone on charge and now stuck in endless reboot loops. Normally the reboot happens during the Cyanogen splash screen, sometimes it makes it past there to an "Optimising Apps" window where it will optimise all apps, but then as soon as it says "Starting apps" it reboots.
I was on stock OS. I have had something similar happen before - always when the battery has died. Previously using the Zuk Z1 toolkit fastboot commands seems to have worked (although I'm not sure if it has ever actually reflashed it as fastboot doesn't appear to work now).
I have tried using fastboot to reflash (stock OS, later ones) - fastboot flash doesn't seem to work (device locked). Using ADB sideload I can reflash (YOG4PAS3AJ, YOG4PAS7DF, YOG4PAS9IG) , but the same ting happens - it seems when the apps are compiled and run it reboots.
All I care about is my photos and videos of my kids - have given up on the phone now (living with a broken home button is frustrating enough).
Can anyone suggest anything? If I could boot the phone up into some sort of safe mode where the apps don't run maybe it would help, but maybe there is no "safe mode" in CM 12.1? Any suggestions would be greatly appreciated.
Thanks
Click to expand...
Click to collapse
You can temporarily boot twrp using fastboot.
fastboot - i 0x2b4c boot twrp.img

Tani2 said:
can you boot into bootloader/fastboot menu etc? being there connect phone to laptop/computer & see if pc shows you the phone drive so that you can copy data for now?
Click to expand...
Click to collapse
I can get into fastboot menu on the phone, and it shows up as a device in windows, but not as a storage device - I don't know if this is normal?
I'll try the fastboot twrp suggestion now, but I think all fastboot commands return "device locked".
Thanks for your attention guys.

Hi,
I have tried to temporarily boot using twrp without the "-i 0x2b4c" and got the following:
FAILED (remote: bootimage: incomplete or not signed)
When I add the -I 0x2b4c switch nothing seems to happen....
:crying:

Related

[ TF300T ] How to unbrick when wrong recovery menu was flashed.

This is how I unbricked my TF300T that had no rom installed and a wrong bootloader/recovery combination. (4.2 bootloader with TWRP recovery JB version). Hope it helps.:good:
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
I have the same on my TF300t and A700 - but it seems i just managed to get my TF300t back
i tried all fastboot (reflashing recovery, boot, system etc) no dice - especially since writing system was done after 3 secs all the time.
Here how i restored my TF300T JB
download your appropriate lates firmware from Asus (WW, US etc.) and extract the zip twice so you have your blob file
install your device drivers if needed (i used Google SDK ones) (and as a Tip Win8 sucks for Fastboot stuff so try to get Win7 Vista XP for this)
Reset your device with a paperclip/needle (about 2 cm down of your sdcard slot) and hold vol-down to enter fastboot
(the folowing i did at least 10 times already but didn't erase misc)
fastboot erase system
fastboot erase recovery
fastboot erase userdata
fastboot erase boot
fastboot erase misc
fastboot erase cache
fastboot -i 0x0B05 flash system c:\adb\TF300t\blob (this is my path - your's may vary depending where you stored your blob) ((also this was the first time i saw the loading bar while flashing)*
fastboot -i 0x0B05 reboot
* it also took a lot longer as it should:
C:\>fastboot -i 0x0B05 flash system c:\adb\TF300t\blob
erasing 'system'...
OKAY [ 1.695s]
sending 'system' (800935 KB)...
OKAY [133.121s]
writing 'system'...
OKAY [153.973s]
finished. total time: 288.789s
im now setting my tab up to get back to CM (which initially caused this sh1theap due to autoupdate error, same as my A700 got bricked )
hope i could help you out!
cheers
-Buster <----(credits to him) Go to this link ---> http://forum.xda-developers.com/showpost.php?p=44244313&postcount=12 because that's the guy that wrote this procedure from above (credits to him) :
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
This part was me now -ozkrtech <--- (credits to me)
In addition to that, if you simply can't see your device using the command "adb devices" go check on device manager if you see a device called just "Transformer" with a yellow icon indicating it needs a driver, and manually update driver, select "browse my computer for drivers" and then select let me pick from a list of device drivers on my computer" there you will see a list of like 3 different drivers, one of them says "bootloader" and one of the others says "adb" (i think they self explain) but just in case try with each one of them you can keep on switching drivers until you get your device recognized by the command "adb devices".
You should be asking yourself... whats the right moment to do an "adb devices" command? well my tablet same as -Buster's tablet had the wrong recovery menu flashed (wrong bootloader version) and it just kept booting into the corrupted recovery (in my case TWRP) with the "can't mount anything" and "what's the password" issue. When you get to password screen just hit cancel and try the "adb devices" commando and you'll see it gets recognized with your device serial number.
Once your device gets recognized by "adb devices" command you will proceed to use "adb reboot-bootloader" command and the tablet will reboot into the menu that had 4 options but now have 3 options and its missing the fastboot option (don't panic) in the last bootloader it is auto-fastboot mode when you reach that screen with just 3 options in it now (yeah is the screen with the RCK option) at this point try "fastboot devices" command to see if your device gets recognized same as "adb devices" procedure, it should get recognized with a different serial number (don't know why, maybe that number isn't a serial number), at this time you are SO LUCKY! now you will follow what I posted at the beginning from that other dude ---> (-Buster) or follow his link --- > http://forum.xda-developers.com/showpost.php?p=44244313&postcount=12
And you'll have an unbricked tf300t in no time =) (I personally used the stock but newest Asus ROM) 4.2.1 (10.6.1.27.1) and it worked flawlessly.
**NOTE** don't turn off nor reset your device once you have formatted the partitions, no need for that (don't know what happends but it might get really hard bricked) just proceed to flash the stock rom after erasing the partitions.
I'm 100% positive this will work if your device is in same state as ours. (had TWRP for JB) then updated bootloader to version 4.2 and forgot to update twrp to version 4.2 or installed twrp version JB by mistake and lost fastboot and TWRP is asking password.
Hope it helps. Let me know your status and if it worked for you.
So I am in the same boat as I flashed the wrong twrp. My device shows up under adb devices and I can boot into the bootloader using adb reboot-bootloader. However, once there, I can not get the device recognized with fastboot. I have tried messing with the drivers like you suggested but nothing will get it to show up with fastboot. Anybody have advice on where to go from here?
So extra info. The device bootloops into twrp 2.6. The only way I can boot into fastboot mode is with adb reboot-bootloader and I can get into APX. I can also boot directly into my current ROM (Slim beta 3) by selecting android in the bootloader menu. I have tried flashing proper recovery through flashify, which is says was successful, but the wrong twrp never gets overwritten. Rebooting the device will send it back to twrp.
Thanks if anyone can help
Thanks, man! It took a while to find this thread, but this was exactly my problem. The adb driver in windows was the pre-solution to help get back to the fastboot server in the bootloader. Awesome information. Thanks again!
I have tried "adb reboot-bootloader" and then adb devices and fastboot devices and neither will show the tab listed while the tab reaches that screen with just 3 options. I have uninstalled reinstalled drivers, it does show in device manager as Asus Android Composite ADB Interface but when running the command it will not list the tablet. Any suggestions?
Hello!
A few days ago I tried to root my Asus TF300T because before that, I changed the lcd and the touchscreen from FPC-1 to G01 version. So I had to root and update touchscreen's firmware to 02-3011-4820.ekt. I already updated with last firmware from asus.com. First, I installed a TRWP recovery but was useless since the touchscreen doesn't worked. So I tried to rewrite CWM recovery. I reset it and I don't remember exactly if I begun to install or not CWM but when I tried to wipe data (Vol- + Power), the tablet has freezed. After a few minutes I did a hardware reset (pin hole). Since that, the tablet freeze with "Device Unlocked", Asus logo and nVidia. The device was already unlocked. I don't have any backup from it. No fastboot, no adb. Just APX mode. Is it possible to do something with it anymore? I tried BootTools2, extracted bloobs from last version of firmware, tryed to flash them with nvflash and wheelie but vainly. What is the next step? I'm a beginner!
Remember please I cannot go in fastboot recovery menu, only apx. Thank you in advance!
I can not thank you enough!!! my tablet is now working I honestly though it was done for aha THANK YOU!!!
Howdy, folks. I recently bricked my tablet thanks to a bad install of CWM, but following the OP's guide I was successfully able to reflash stock firmware and the device runs fine now.
However, upon reflashing said firmware, it became apparent to me (from reading various threads in the development subforum), that I would need to downgrade to an older firmware version to reflash TWRP. So I did that successfully, but now I am having a problem similar, or perhaps identical, to that of Bionicbowtieguy, in that ADB appears to be broken for my tablet. I have tried uninstalling and reinstalling the Asus usb drivers, in addition to reinstalling/updating all of the ADB software. Fastboot still works fine, but as such I'm unable to root using Motochop's rooting kit (I know there are other methods out there), nor am I able to flash a new recovery. I have also tried repeatedly reflashing the older stock in the hopes that ADB would magically start working again to no avail.
Does anyone have any suggestions to getting ADB to work for my tablet again? I have scoured the web, particularly these forums, for days looking for an answer, but haven't turned anything up yet. Any help would be greatly appreciated.
Gave back 10 years of my life that I lost once I discovered I flashed the wrong TWRP version. Can't thank you enough man.
Kombatant said:
Gave back 10 years of my life that I lost once I discovered I flashed the wrong TWRP version. Can't thank you enough man.
Click to expand...
Click to collapse
Same here!
Thank you OP for making this a topic even if you didn't come up with it you made it a thread that has saved a few people like myself money and headaches. Literally I just stumbled on this thread 10 minutes after I told my wife is be Tablet shipping Black Friday. Thank you sir.
Thank you.
I did this on a hackintosh running OSX since on Win 8.1 fastboot kept crashing.
March of this year I bricked my tablet during that 1 week period where nobody knew that TWRP was broken + fastboot freezing.
I must have tried everything, Maybe that erase misc was the key factor for success.
I was about to sell this for what I could get or send it to asus, now I can use it again!
How are you guys getting your tablet into fastboot mode? I've tried power on with volume down, the reset hole with volume down, and letting the battery die then recharge, then power on with volume down... Nothing. What am I doing wrong?
Sent from my Galaxy Nexus using Tapatalk
Best thread ever!! You are a life saver !!! thank you!!
leris2 said:
Best thread ever!! You are a life saver !!! thank you!!
Click to expand...
Click to collapse
Indeed. You are a god among men. Thank you so much
This worked! I thought I was out of luck. Thanks a lot.
I accidentally flashed an incomparable version of twrp. It would only boot straight into recovery and I couldn't get into recovery. TWRP kept asking for a password even though I never set one up and it wouldn't mount the internal storage or sd card.
I had to follow the instructions at the bottom to intall the drivers so adb and fastboot to work. After that I followed the instructions at the top.
The only thing different I did was skip the "fastboot erase boot" step. I was afraid that would really brick my device if I screwed up (Does this really erase the bootaloader leaving the device with no bootloader?).
Just wondering how long the fastboot window sits displaying < waiting for device > ? All my drivers are ok and I my pad shows up fine as a fastboot device in windows.
Cheers
Fastboot
Bolandk said:
Just wondering how long the fastboot window sits displaying < waiting for device > ? All my drivers are ok and I my pad shows up fine as a fastboot device in windows.
Cheers
Click to expand...
Click to collapse
They do not sit at all they will go right to it. You must not have the right combination yet. Keep trying.
Took me awhile to get the link.
norm883
FIXED!
BY GOD, I have no words for how incredible grateful I am right now! You not only saved my TF300T's life but also a lot of money for me and gave me another lesson of Android insight.
Thanks so much for this!
Let me know if I can return the favor somehow!
Regards,
(a very happy) philleicht
Hi. I think I'm having the same problem as some of the others in this thread.
Background: Tablet is unlocked, JB Rom (Paranoid Android) was installed since March, along with TWRP recovery. In preparation of installing CM11, I used Android Terminal Emulator to install the latest TWRP from a *.blob file, but I found that the latest TWRP is still not CM11-ready...
Setup to Issue: Last night, I decided I wanted to put CM11 on my TF300T. TWRP doesn't have a compatible recovery out for CM11 (install of CM11 rom fails every time), so I reinstalled the paranoid android ROM, and attempted to get the latest recovery from clockworkmod. On cwm's website, they only have choices for "transformer" "transformer prime" and "transformer infinity" which, when downloaded, have tf101, tf201, and tf700 in their filenames. (No tf300, that is)
So... I attempted to install the tf201 recovery (closest to mine, right?) by renaming the file cwm.blob, and using android terminal emulator to install it, the same way I did with TWRP. The first few times I tried and rebooted into recovery... TWRP was still installed... which was weird to me.
The big problem: Ultimately... when I rebooted the tablet, I just see the initial "ASUS" screen with "The Device is UnLocked." in the top-left corner. When I hold the power button to turn it off... it powers back on within a few seconds, and stays at the "ASUS" screen again. It will not stay off... and will not show anything but the "ASUS" splash screen. (With one exception, described later - "the only ray of hope...") If I hold the volume up or down buttons when powering on the device, absolutely nothing different happens. (since it doesn't STAY off... I've tried all kinds of different combinations of pushing/holding the appropriate buttons for when the tablet comes back on) IMPORTANT: I never see the "three icons" as expected when holding the volume button(s). No RCK, USB, etc... when the unit turns back on, it goes to the ASUS screen, and stays there until the battery dies. As a result... I can't get into recovery, fastboot, or APX or whatever in the traditional way.
Pressing the reset button alone, or reset + volume down has the effect of temporarily turning off the unit and then on again, the same as holding the power button to turn it off and letting it turn itself back on again.
The only ray of hope that I have is that *sometimes* if I press reset + volume up with the USB cable connected to a computer... the screen will STAY BLACK, but the "device connected" sound will play on my PC (Win 7 x64) as if I just plugged the tablet into USB on my computer, and I will get a message that it's trying to install an APX device. However, it eventually tells me that the device driver could not be installed. The screen on the tablet stays black in this case... until I reset it, hold the power button, etc.
So... I'm not opposed to (or unfamiliar with) using fastboot or any other command-line app to resurrect my tablet... I just haven't been able to get it into a condition that I can try something like that yet.
Is there any hope for my tablet? Somebody please help me. I'm open to sending a few bucks via paypal or google wallet to anyone that can lead me to a resolution. That would be cheaper than buying a new tablet... not to mention the priceless value of the progress I have in Fieldrunners 2. lol.
Thanks for your time!
~Ryan
same problem reboot back to twrp
well i may be stupid because i can't understand why i have tried a couple of commands and i still get the same problem reset volume down still goes back to twrp and ask for a password can someone please explain this in alittle more detail and what commands i also get the waiting for device in my commands is there another way to push these files into this device tf201 please help is there a way to do something in the twrp recovery like terminal command
I was a fool for flashing wrong recovery!
DrPhant0m said:
Hi. I think I'm having the same problem as some of the others in this thread.
Background: Tablet is unlocked, JB Rom (Paranoid Android) was installed since March, along with TWRP recovery. In preparation of installing CM11, I used Android Terminal Emulator to install the latest TWRP from a *.blob file, but I found that the latest TWRP is still not CM11-ready...
Setup to Issue: Last night, I decided I wanted to put CM11 on my TF300T. TWRP doesn't have a compatible recovery out for CM11 (install of CM11 rom fails every time), so I reinstalled the paranoid android ROM, and attempted to get the latest recovery from clockworkmod. On cwm's website, they only have choices for "transformer" "transformer prime" and "transformer infinity" which, when downloaded, have tf101, tf201, and tf700 in their filenames. (No tf300, that is)
So... I attempted to install the tf201 recovery (closest to mine, right?) by renaming the file cwm.blob, and using android terminal emulator to install it, the same way I did with TWRP. The first few times I tried and rebooted into recovery... TWRP was still installed... which was weird to me.
The big problem: Ultimately... when I rebooted the tablet, I just see the initial "ASUS" screen with "The Device is UnLocked." in the top-left corner. When I hold the power button to turn it off... it powers back on within a few seconds, and stays at the "ASUS" screen again. It will not stay off... and will not show anything but the "ASUS" splash screen. (With one exception, described later - "the only ray of hope...") If I hold the volume up or down buttons when powering on the device, absolutely nothing different happens. (since it doesn't STAY off... I've tried all kinds of different combinations of pushing/holding the appropriate buttons for when the tablet comes back on) IMPORTANT: I never see the "three icons" as expected when holding the volume button(s). No RCK, USB, etc... when the unit turns back on, it goes to the ASUS screen, and stays there until the battery dies. As a result... I can't get into recovery, fastboot, or APX or whatever in the traditional way.
Pressing the reset button alone, or reset + volume down has the effect of temporarily turning off the unit and then on again, the same as holding the power button to turn it off and letting it turn itself back on again.
The only ray of hope that I have is that *sometimes* if I press reset + volume up with the USB cable connected to a computer... the screen will STAY BLACK, but the "device connected" sound will play on my PC (Win 7 x64) as if I just plugged the tablet into USB on my computer, and I will get a message that it's trying to install an APX device. However, it eventually tells me that the device driver could not be installed. The screen on the tablet stays black in this case... until I reset it, hold the power button, etc.
So... I'm not opposed to (or unfamiliar with) using fastboot or any other command-line app to resurrect my tablet... I just haven't been able to get it into a condition that I can try something like that yet.
Is there any hope for my tablet? Somebody please help me. I'm open to sending a few bucks via paypal or google wallet to anyone that can lead me to a resolution. That would be cheaper than buying a new tablet... not to mention the priceless value of the progress I have in Fieldrunners 2. lol.
Thanks for your time!
~Ryan
Click to expand...
Click to collapse
I have exactly this! I hope someone knows the answer for this issue. Else the tablet will learn how to fly!
I tried to push the reset button as described earlier but nothing changes. Not able to go into recovery Just stuck at ASUS in the middle NVidia in the bottomright corner en upperleft corner 'this device is unlocked'

[Q] Stuck in fastboot, cannot use controls, already flashed everything, any ideas?

So to answer the first question, yes I followed the stickied guide up top, and yes, it successfully flashed the bootloader, wiped all data, and flashed stock ROM all to success. It appears my case is unique. I was told that it could be the battery connection, so I've done no fewer than half a dozen times of taking the back off, resetting the battery connection, and closing back up. It does not appear to be the battery.
I am stuck on the fastboot screen, the one where the android is lying down and blue squares project from an body. It shows me the controls I can make with the volume switches and the selection choice of 'Start'... but I cannot do anything. Before I went to flash I could move through the selection with Vol Up ONLY, but now I cannot even do that. Here's all the mode says:
Code:
FASTBOOT MODE
product name - grouper
variant - grouper
hw version - er3
bootloader version - 4.23
baseband version - n/a
serial number - ###############
signing - not defined yet
LOCK STATE - UNLOCKED
I've pretty spent the past twenty four hours on google searching through all the threads I've seen. They are either all dead, or most of them found the sticky fixed their problem. Has anyone heard of it coming to this?! All I can do is access fastbook VIA a DOS prompt and do fastboot commands, and if I disconnect the tablet from my PC, it'll remain in this mode with the screen on until the battery dies. Charging appears to charge the tablet, but again, no controls work. And yes, the buttons were set properly when I closed my tablet.
Anyone?
1) what is it exactly that your trying to do?
2) can u boot into the OS?
3) your recovery may be corrupt re-flash the recovery via fastboot
...Awesome... said:
1) what is it exactly that your trying to do?
2) can u boot into the OS?
3) your recovery may be corrupt re-flash the recovery via fastboot
Click to expand...
Click to collapse
I'm just trying to boot up! I don't know what happened, but I haven't been able to use it for school all week!
I cannot boot into the OS. Any time I plug this device in it sends me to the fastboot screen with no controls.
OK I just flashed CWMR 6.0.4.3 and it did not fix the problem.
Any other ideas?
I just repeated all the steps again to see if any of them failed before, they have not worked. So recap:
Stuck in fastboot mode
Android will not boot
Loose battery connection is not the problem
I am able to access fastboot on my computer
I have followed everything from the sticky (wipe everything, flash bootloader, flash image)
I have flashed a new recovery
I am still stuck in fastboot
I cannot control options in fastboot with the volume and power buttons
I can only access fastboot by charging my tablet
The only way the tablet will power down is when it completely depletes it's battery
As far as I can tell, nothing was wrong with the tablet when it was functioning
This happened when I went to charge my tablet, presumably when the battery ran flat running android
If I charge too long the tablet gets fairly hot.
That's about all the information I can provide. Is there anything else I can try? Please, I need a tablet for school and I cannot afford a new one!

[Q] Rooted Nexus 10 Stuck in Bootloop, Please Help!

Hello all,
Any help with this would be seriously appreciated. I rooted my Nexus 10 a while back, maybe two years ago. I'm not very proficient with this stuff. Anyhow I decided to do the OTA upgrade to 5.0...I was concerned something would go wrong unless I went to stock first, but I read that the only thing that would happen is root would be removed.
Anyhow, the tablet appears stuck while booting. I see the Google screen first with the unlocked indicator on the bottom. A few seconds later is the Android logo on its back, a red triangle over it with an exclamation point and "no command" written below". It stays that way for a minute or so, tries to reboot and goes back to the no command screen. I can't even power off, when I try to do so it just powers back on by itself and ends up at the no command screen again.
I tried booting into recovery (power, volume up, volume down). My options from here are either Start, Restart Bootloader, Recovery Mode or Power Off. Every option I choose leads to the No Command Screen (except power off, which powers off). No idea what to do from here.
Any help at all would be appreciated. As you can probably tell I don't have much experience with this and just wanted to go back to unrooted stock. If you have advice, please be clear. I can follow directions well enough, just don't have much experience here. Thanks in advance.
Same here, bootloop.
Same thing here. A seemingly short download of Lollipop (even though I have 50Mbs internet). Installation, reboot, and now it loops endlessly. I can get to the bootloader or into Download mode, but that's all. Recovery mode just reboots. I was rooted and had TWRP installed. Other than that, I was running stock 4.4.4.
I've rooted all my devices, and installed various ROM's on several devices. I have the full ADB installation. I have the Nexus Root Toolkit installed. The problem is, the device will not show up under "Devices" on the computer itself. I've installed every USB driver there is (and uninstalled each one after it does not work, so no I do not have several USB drivers installed). Of course nothing shows up using "adb devices" either. Nexus Root Toolkit also cannot find any devices. I've read everything on this subject I can find, and there are no answers out there. Anyone have ANY ideas??
Thanks
Guys, if your device is connected in fastboot (try "fastboot devices") then you can flash roms or recovery (and then flash rom) from there. There are multiple threads with the same problems out there which were fixed. E.g: http://forum.xda-developers.com/nexus-10/help/bricked-t2948546
In my example, I flashed TWRP recovery from fastboot, then installed custom ROM from recovery (official ROM failed to install for some reason). Try this, it might help.
danweis said:
Same thing here. A seemingly short download of Lollipop (even though I have 50Mbs internet). Installation, reboot, and now it loops endlessly. I can get to the bootloader or into Download mode, but that's all. Recovery mode just reboots. I was rooted and had TWRP installed. Other than that, I was running stock 4.4.4.
I've rooted all my devices, and installed various ROM's on several devices. I have the full ADB installation. I have the Nexus Root Toolkit installed. The problem is, the device will not show up under "Devices" on the computer itself. I've installed every USB driver there is (and uninstalled each one after it does not work, so no I do not have several USB drivers installed). Of course nothing shows up using "adb devices" either. Nexus Root Toolkit also cannot find any devices. I've read everything on this subject I can find, and there are no answers out there. Anyone have ANY ideas??
Thanks
Click to expand...
Click to collapse
Go to Fastboot mode (pwr+both volumes), Than select recovery after a while an android with Exclamation mark appears which is a stock recovery screen. To access the stock recovery menu press and hold power than press one of the volume keys so the menu will appear. Than do a factory reset and clear caches. You can than reboot and wait for boot animation to finish (it wont take long this time) and you will boot.
If this doesnt work you can flash a stock factory image easily from fastboot again.
Aresmar said:
Go to Fastboot mode (pwr+both volumes), Than select recovery after a while an android with Exclamation mark appears which is a stock recovery screen. To access the stock recovery menu press and hold power than press one of the volume keys so the menu will appear. Than do a factory reset and clear caches. You can than reboot and wait for boot animation to finish (it wont take long this time) and you will boot.
If this doesnt work you can flash a stock factory image easily from fastboot again.
Click to expand...
Click to collapse
I also had the same problem... I followed these instructions and now my Nexus 10 can boot normally (it took a long time to boot).
Only problem is all my data was deleted.... stup*d f*cking sh*t!!!!!!!

Lenovo Yoga 2 1050L stuck at Lenovo logo/'Fastboot starting...' after rooting attempt

Hello,
before I get into detail with my current problem at hand, I want to say that I'm extremely new to flashing/rooting my tablet and in most cases am very dependent on guides and how-tos. That being said, I've search through this forum among others in order to get my problem solved but had no success so far. So your expertise is basically my last resort and hope.
I have a Lenovo Yoga 2 1050L, as stated above, and tried to root it yesterday using this guide. Unfortunately, I messed up when it came to the system's image from the custom ROM because I downloaded the original firmware for the 10'' version L instead of the further below mentioned recovery firmware in step 3 (though that link was dead anyway). Moreover, I also included the recovery.img in the custom flash process and not only the system.img and I think the error occurred while flashing the recovery partition.
Long story short, the flashing process failed and I was left with a non-booting tablet.
The status-quo is I can boot into the bootloader mode (power button + volume down) where it'll say "normal boot", "recovery mode" etc. at the top with the android figure lying on the ground with an open stomach.
With the help of the Fastboot Tethered Recovery Launcher I can use the T3 option to change the device status to "fastboot-online". From what I understood I can then enter recovery mode if pressing volume up (so I can do a data/cache wipe) but it says
"could not open sys/devices/virtual/backlight" and I couldn't figure out what that's supposed to mean or how I can solve it.
I also tried to flash it again with the stock rom downloaded from here with the Intel Phone Flash Tool 4.4.4.
But that always failed at the "fastboot -s <device> oem wipe ESP" operation. It failed to execute that command resulting in a timeout only to try it once again. After that second attempt ended in a timeout too, it went on to the next step "fastboot -s <device> oem start_partitioning" but that also failed, ultimately making the whole flash process fail.
The curious thing (for me, anyway) was that I could flash the boot.img, system.img and recovery.img individually (by going to "Custom Flash" in the Phone Flash Tool and then selecting only one of those images) and all three processes succeeded. However, I only got the success message on the Phone Flash Tool, the tablet itself got stuck during the first reboot during or after the flash process.
In fact, every boot/reboot results in the tablet being stuck at the display of the Lenovo Logo. Nothing happens after that, it just stays there.
This happens whenever I try to boot normally or boot straight into recovery mode (Power + Volume Up). The only way I can boot my tablet and actually do something with it is the bootloader mode (Power + Volume Down) but as stated above, from there I didn't manage to get anywhere else so far.
Another thing I have tried is to enter fastboot mode because I read that I can also recover from there. But whenever trying to enter fastboot mode the tablet's display goes black, then a small text says "Fastboot starting..." and that's it. Nothing happens after that, no additional text or new screen.
What I also noticed is that whenever the tablet reboots itself or if I try to boot/reboot it, the tablet is not in the list of available devices anymore if I enter "adb devices" or "fastboot devices" in my command line (with connected tablet). Only when I redo the process with the Fastboot Tethered Recovery Launcher (option T3), can I access the device with those commands again (at first I could access it with "adb devices", later on only with "fastboot devices" and to be honest, I don't know why that is).
I actually just want to wipe the data of the tablet and install the stock ROM again because I think there's just some corrupt data that keeps my tablet from booting normally. But right now I don't even know how to do that because everything I've tried so far didn't work. Not even starting the tablet with the so-called "hard reset" (Power + Volume Down + Volume Up) worked, I only got a black screen in that case.
Because I tried to solve this problem myself all day yesterday, my tablet is now also down to about 20% of battery and I don't know if I can charge it up without a proper ROM installed (probably not). So that's another factor that's hindering me from trying out other steps.
I know this is a lot of text but I still hope there's someone out there who can help me with my problem. I am at my wit's end and would highly appreciate anyone who has knowlegde about this situation with this tablet helping me.
Best regards and thank you in advance
XShunyaX

Ticwatch c2 stuck in boot loop after factory reset.

Hey all, I recently flashed a new rom on my phone, which required me to factory reset my ticwatch I'm order to reconnect.
Upon doing to the first time, everything seems to have gone well, but had trouble connecting to the device. So I ran another factory reset. Since that one, I've been stuck in a boot loop.
I see the "device software can't be checked for corruption" screen for about 20 seconds, and then it vibrates, screen turns off, then I see the same screen again. And so on.
I tried letting the battery go to nothing and trying again, seems to be the same issue. I'm letting it charge and bootloop for now in case maybe I just don't have enough juice to make it through boot.
It is rooted, with custom ROM (followed a guide on this forum somewhere about half a year ago, was running great) and TWRP installed (at least it was, I've been unable to get to the recovery screen since the boot loop started). Cannot see it in adb ever in this process.
Anyone have any other suggestions? I remember the Samsung notes had a special USB tool that would bridge a couple pins to immediately go to recovery, is there a similar option here?
Can you get in usb mode,or fastboot or recovery maybe?There is solution..dont worry.I ghuess adb dont work,but you cant go to fastboot mode and boot twrp image and get in twrp recovery..in twrp recovery you need backup file..If you cant do that,we are going to another solution..
Yeah, I can't - via any combination of button holding - get into any booted mode. No recovery, no fastboot, nothing. If anything, some buttons seem to make it circle boot faster .
nieminen432 said:
Yeah, I can't - via any combination of button holding - get into any booted mode. No recovery, no fastboot, nothing. If anything, some buttons seem to make it circle boot faster .
Click to expand...
Click to collapse
,Yeah tough situation,and when you connect it to pc in that "broken mode" -boot loop and open adb shell on pc ,comand adb devices or fastboot devices,does it show device?When you screwed boot and you have twrp there must be option to get in twrp.One trick more go to manage devices in pc find your device if unknown you right klick on it,update drivers,manually,and then choose android,then android adb install device.
KristijanKG3 said:
,Yeah tough situation,and when you connect it to pc in that "broken mode" -boot loop and open adb shell on pc ,comand adb devices or fastboot devices,does it show device?When you screwed boot and you have twrp there must be option to get in twrp.One trick more go to manage devices in pc find your device if unknown you right klick on it,update drivers,manually,and then choose android,then android adb install device.
Click to expand...
Click to collapse
I tried adb devices, but not fastboot devices, thanks for the idea, I'll give it a go.
nieminen432 said:
I tried adb devices, but not fastboot devices, thanks for the idea, I'll give it a go.
Click to expand...
Click to collapse
Maybe it wont work,but if doesnt,we figure out something..Bootlop is not the end of your device..
No go on either command. Nothing shows up.
I'm half wondering if it's my battery at this point. I think I'm getting a new watch for Christmas anyway, so not a huge loss. But happy to keep trying if anyone else has any ideas.

Categories

Resources