Related
I was on MALICE rom (JVQ) and i was trying to update to v 4.1.1 with the frameworkres.apk and in the process i had to delete the existing one that i already had with root explorer so i can install the apk that is posted in his thread but i had to reboot and now it will not boot to download mode or recovery mode. I tried all button combinations and all sorts of ways but cannot reboot to anything else. I'm stuck on galaxy s logo. Anybody know how to get to download mode or recovery mode from here or to restore phone to stock??
Did you paste the framework res apk into the system/framework folder? All you had to do has paste it in there. You didnt have to delete anything. And keep trying the button combos or buy a jig.
Same thing happen to me on SH, I kept trying for one hour until it did it. Pull the battery, put it back in, plug phone into pc until you see the charging indicator, then try vol down and power button or both volumes and power. Keep trying that until it boots into recovery.
For d/l mode make sure phone is plugged into pc and its vol. up and power. That should work every time.
The button combo's are different for GB bootloaders. If you can't get into download mode with the button combination you should look into purchasing a jig. Good luck!
*EDIT*
You should probably replace system files, instead of deleting and then moving this way there is one in there at all times. If that makes any sense.
battery out. put battery back in hold volume up and down at the same time continue holding and plus in usb. flash using odin with your pit and pda. if u see a phone with this (!) just plug it in load ur pit and pda and click start on odin. it has worked for me once before
Don't know what could be wrong here... I've tried to boot the device into flash mode:
1. keep reset button pressed
2. insert power cable
3. connect the other end of the USB cable to PC
After the steps above I saw the usual android robot on the device screen, then I simply disconnected power and USB cable (nothing else has been done). Now if I power on the device it boots always in download mode... I can boot the device into "flash" mode in the same way, but _without_ connecting power cable, the device is recognizable by the Rockchip Batch tool or the rkflashtool. With the last tool I can read/backup everything, but the device is booting only in the download mode. I'd appreciate any ideas.
EDIT: Sorry for the noise... It just takes a long while to boot with different android logo the first time after entered flash/recovery mode.
Sorry, wrong thread ...
Hello, today i shutted off my xiaomi redmi2 and it shutted off normally.
But it doesnt start back again at all, i tried another battery and i tried charging the phone for several hours straight.
Testpoint method does not work and when i connect the phone to windows 10 pc it just keeps dissconnecting and connecting again several partitions (i think it is linux composite device, ive seen it in another snapdragon phones in the past)
Does anyone have any idea how to fix this phone ?
Btw at the time this happend i was on global stable miui, but the phone was previously running ressurection remix with stock kernel.
u have try to boot into fastboot or recovery?
if u boot in both then u can flash stock rom.. and fix this problem....
I assume you have Redmi 2 snapdragon variant since you have flashed global rom. Try to boot into fastboot mode by pressing Vol Down + Power. Download fastboot rom for redmi 2. Link
and minimal adb and fastboot Link
Extract the fastboot rom file with winrar (.tgz) and you will get a folder named "wt88047..........." inside that folder, there will be a subfolder named images. Extract minimal adb and fastboot to the wt88047 folder. It should look like this:
http://postimg.org/image/3r2hg2nhj
Run any .bat and fastboot process will start
Thanks for replies but it is completely hard bricked, i cant access recovery,fastboot and bootloader and the phone is not booting
Just some help
Spasik said:
Thanks for replies but it is completely hard bricked, i cant access recovery,fastboot and bootloader and the phone is not booting
Click to expand...
Click to collapse
So if its not going into fastboot then it must be the battery's problem or (the one i faced)DEAD SCREEN...if you feel vibration but no display then its probably just the dead screen.
There's no solution for it at home, u have to visit service centre.
If you have a custom rom installed, then switch back to factory to bring back warranty.
As said before, if it vibrates but no display the phone's still working(just the display is gone). Reboot into fastboot mode by VOL DOWN+POWER or VOL DOWN and insert usb while keeping the button pressed.. then go to the folder where you have extracted fastboot.exe and then SHIFT+RIGHT CLICK> Open Command Window Here...a cmd window opens up the type in:- fastboot devices...
If there's an output then your device is connected.....Later reply to this if that works
Thanks i will try it
@Blazerstriker Thank you very much, the phone went to fastboot and i fixed it
Hi. I have same problem but get no output from c:\adb> fastboot devices. Pressing vol- and power does nothing. With phone connected to Windows 10 pc by USB I get connecting and disconnecting sounds over and over but phone does not show up.
hp1337 said:
Hi. I have same problem but get no output from c:\adb> fastboot devices. Pressing vol- and power does nothing. With phone connected to Windows 10 pc by USB I get connecting and disconnecting sounds over and over but phone does not show up.
Click to expand...
Click to collapse
Pull the battery out, put it back in and connect the phone to pc while it is powered off and when you are connecting it hold the vol-
That is the only thing that worked for me
Thanks for the suggestion but phone still doesn't show up on pc and screen is still blank
hello,
after install some rom, my p9 lite get bootloop. I manage to enter fastboot but phone was locked, so to install twrp i unlocked it.
After unlock i can't enter fastboot.
Screen "your devices has been unlocked and can't be trusted" appears, vol up+- power, nothing happens phone vibe 2 times and back to screen "your devices...".
My bootloader is unlock, can i flash twrp without bootloader screen on phone ? My phone is connected to PC but no device detected. Maybe at linux i can do something more than windows ?
Maybe i need to go to fastboot some different way ? i try to push 3 button after fist vibe and 2nd. Nothing work for me :crying:
i tried to past b130 to sd card in dload, vol+- power, nothing not even update screen, same "your devices"....,
now downloading b151
dragon218 said:
hello,
after install some rom, my p9 lite get bootloop. I manage to enter fastboot but phone was locked, so to install twrp i unlocked it.
After unlock i can't enter fastboot.
Screen "your devices has been unlocked and can't be trusted" appears, vol up+- power, nothing happens phone vibe 2 times and back to screen "your devices...".
My bootloader is unlock, can i flash twrp without bootloader screen on phone ? My phone is connected to PC but no device detected. Maybe at linux i can do something more than windows ?
Maybe i need to go to fastboot some different way ? i try to push 3 button after fist vibe and 2nd. Nothing work for me :crying:
i tried to past b130 to sd card in dload, vol+- power, nothing not even update screen, same "your devices"....,
now downloading b151
Click to expand...
Click to collapse
For fastbooting u need to use volume down and power in the same time and the phone needs to be connected to PC, and for entering to recovery u only need to press volume up and power key.
robi10101298 said:
For fastbooting u need to use volume down and power in the same time and the phone needs to be connected to PC, and for entering to recovery u only need to press volume up and power key.
Click to expand...
Click to collapse
phone is connected to pc. screen is on "your device..." i push vol down + power. screen going black vibe 2 times, 1 sec huawei logo and back to "your device..". I don't know why after unlock phone i can't go to fastboot
i it possible to erase fastboot ??!!
dragon218 said:
phone is connected to pc. screen is on "your device..." i push vol down + power. screen going black vibe 2 times, 1 sec huawei logo and back to "your device..". I don't know why after unlock phone i can't go to fastboot
Click to expand...
Click to collapse
Disconnect the phone from PC. Make sure it's powered off. Plug in USB cable at the same time while holding volume down.
zgomot said:
Disconnect the phone from PC. Make sure it's powered off. Plug in USB cable at the same time while holding volume down.
Click to expand...
Click to collapse
don't work, after power on still going to "your devices". Even change pc and usb cable
I can belived that i can open fastboot when phone was lock, after unlock fastboot vanished
dc-phoenix can help if pc dont see device ?
dragon218 said:
don't work, after power on still going to "your devices". Even change pc and usb cable
I can belived that i can open fastboot when phone was lock, after unlock fastboot vanished
dc-phoenix can help if pc dont see device ?
Click to expand...
Click to collapse
Don't work, after power on......why power on?
Disconnect from PC. Power of the phone.
Press and hold only vol down, with pressing vol down connect with PC. Device should be start on fastboot mode.
Sent from my NEM-L21 using Tapatalk
Anonda said:
Don't work, after power on......why power on?
Disconnect from PC. Power of the phone.
Press and hold only vol down, with pressing vol down connect with PC. Device should be start on fastboot mode.
Sent from my NEM-L21 using Tapatalk
Click to expand...
Click to collapse
in 5 min i will send video i think i'm doing everything right
if u can look at it
http://sendvid.com/svihvenb
No compatible source was found this video
Sent from my NEM-L21 using Tapatalk
Anonda said:
No compatible source was found this video
Sent from my NEM-L21 using Tapatalk
Click to expand...
Click to collapse
try this from yt
https://youtu.be/K36zMsaP4As
try putting update.app file into dload folder on your sdcard and updating via three button method.
sirjohnrl said:
try putting update.app file into dload folder on your sdcard and updating via three button method.
Click to expand...
Click to collapse
Try with b130 and b161 for region c432 nothing happened. 2 days ago i change region from c185 to c432 now i think maybe i need to past c185b161 to work ?
update doesn't start either, losing hope some one have any other ideas ?
dragon218 said:
try this from yt
https://youtu.be/K36zMsaP4As
Click to expand...
Click to collapse
On the starting, your phone is on.
Then you shutdown? How?
After power off
Press and hold only vol down, connect with pc.
Hi suit installed on your PC?
Sent from my NEM-L21 using Tapatalk
Anonda said:
On the starting, your phone is on.
Then you shutdown? How?
After power off
Press and hold only vol down, connect with pc.
Hi suit installed on your PC?
Sent from my NEM-L21 using Tapatalk
Click to expand...
Click to collapse
i hold power button, if phone isn't connected to pc he is going off. Think is because battery is very low, led is blinking in red.
Then I hold vol down and connect usb cable, but how u can see on video phone weak up and go to booting.
I have hi suit last night as i mention fastboot works, but need to unlock phone. After that "your devices" screen came out and can't fastboot anymore
When i turning off phone with connected usb i can't turn phone off. After a second phone power on by his own.
If phone is disconnected longer than 5 min, then i push vol down and connect usb only red lightening shows up. I need to wait a while to phone start.
dragon218 said:
i hold power button, if phone isn't connected to pc he is going off. Think is because battery is very low, led is blinking in red.
Then I hold vol down and connect usb cable, but how u can see on video phone weak up and go to booting.
I have hi suit last night as i mention fastboot works, but need to unlock phone. After that "your devices" screen came out and can't fastboot anymore
When i turning off phone with connected usb i can't turn phone off. After a second phone power on by his own.
If phone is disconnected longer than 5 min, then i push vol down and connect usb only red lightening shows up. I need to wait a while to phone start.
Click to expand...
Click to collapse
OK. When phone is off, if you connect with PC, phone should be start, but this is only for charging. May be, you don't have charge, so phone is not going to fastboot mode with vol down?
Now just connect the phone with PC for full charge.
You don't have any recovery? Custom or stock?
It can be happen?
Sent from my NEM-L21 using Tapatalk
Anonda said:
OK. When phone is off, if you connect with PC, phone should be start, but this is only for charging. May be, you don't have charge, so phone is not going to fastboot mode with vol down?
Now just connect the phone with PC for full charge.
You don't have any recovery? Custom or stock?
It can be happen?
Sent from my NEM-L21 using Tapatalk
Click to expand...
Click to collapse
When i start charge phone blinking red in led, after while phone vibe 1 time and go to booting now, but led don't stop blinking. I will try to charge it, but because of working screen, phone heat a lot i don't wanna burn it.
Before i made rollback and something gone very bad, emui update after 100 % phone don't boot up. Without usb cable i wasn't able to go recovery or fastboot. So i think i don't have any recovery i made backup of files with twrp but now i can't flash it.
after night without power, phone drain all of battery. Now i understood better what is going on. when i plugged usb cable, phone don't start bye it own, only red lighting flash for second .
I disconnect cable and connect it with vol down button how all of here wrote. Phone immediately weak up an go to "your device has been..".
It's look like after i unlock phone (bootloader) somehow i was able to corrupt bootloader files or even delete it. Some one can confirm that it is possible to crash bootloader ?
dragon218 said:
after night without power, phone drain all of battery. Now i understood better what is going on. when i plugged usb cable, phone don't start bye it own, only red lighting flash for second .
I disconnect cable and connect it with vol down button how all of here wrote. Phone immediately weak up an go to "your device has been..".
It's look like after i unlock phone (bootloader) somehow i was able to corrupt bootloader files or even delete it. Some one can confirm that it is possible to crash bootloader ?
Click to expand...
Click to collapse
I have the same situation. I tried everything, Three button method, letting the battery run out completely, Vol+ and Power, Vol- and Power, connected to PC, not connected to PC. Every time I disconnect the charger, and reconnect it starts from 0. I read some other people here have the same problem. Send it to warranty and explain your rollback process unlocked the bootloader somehow (I mean the phone does do a lot of sh*ty sh*t, so this shouldn't seem very odd as well!!!) and hope that you get a repair/replacement and after that sell it on ebay hoping some stupid people like us in the first place will buy it and spend your money on a phone more reliable!
I managed to access the fastboot using the 3 button method in cold boot. Hold the Power key until the screen goes off and then release and hold down the Vol- key and immideately connect the usb cable to PC right before it vibrates or exactly when it vibrates (it's a matter of timing), and bingo you are in fastboot and you can flash system.img, recovery.img, cust.img, cache.img and boot.img from there, but this is not how I revived my phone. I used the 3 button method again when the phone was charged for like half an hour or so and the did the same cold boot trick and I could boot into the force upgrade environment (strangely this still didn't work whitout connecting the usb cable to PC), but it somehow didn't want to read the UPDATE.APP that I had in dload folder on my SD card and wanted to have it from my PC (I just felt it nad there was no indication of it ) so then I installed the DC Phoenix tool and payed 15 euros to be able to inject the complete UPDATE.APP to my bricked phone and the installation went well to 99% and failed, but I rebooted the phone and I could boot normally. Just to make sure I did a factory reset afterwards. Hope this helps.
bahador_b_92 said:
I managed to access the fastboot using the 3 button method in cold boot. Hold the Power key until the screen goes off and then release and hold down the Vol- key and immideately connect the usb cable to PC right before it vibrates or exactly when it vibrates (it's a matter of timing), and bingo you are in fastboot and you can flash system.img, recovery.img, cust.img, cache.img and boot.img from there, but this is not how I revived my phone. I used the 3 button method again when the phone was charged for like half an hour or so and the did the same cold boot trick and I could boot into the force upgrade environment (strangely this still didn't work whitout connecting the usb cable to PC), but it somehow didn't want to read the UPDATE.APP that I had in dload folder on my SD card and wanted to have it from my PC (I just felt it nad there was no indication of it ) so then I installed the DC Phoenix tool and payed 15 euros to be able to inject the complete UPDATE.APP to my bricked phone and the installation went well to 99% and failed, but I rebooted the phone and I could boot normally. Just to make sure I did a factory reset afterwards. Hope this helps.
Click to expand...
Click to collapse
Now your phone is OK?
Sent from my NEM-L21 using Tapatalk
Anonda said:
Now your phone is OK?
Sent from my NEM-L21 using Tapatalk
Click to expand...
Click to collapse
Yes. I am actually writing this from my Huawei P9 Lite now. This phone is really a nightmare for modifying and customization. I'm not sure if I'm going to resell it or just wait a reasonable amount of time until some reviews from the next update come out and see if I might wanna take the risk and update my phone again.
Hoping someone can shed some light. Rushing to root phone again to send back warranty replacement, in my haste my laptop died mid flash and now can only boot in Fastboot and Crashdump Mode.
I am attempting to restore to factory via the MSM tool but cannot for the life of me enter EDL mode.
With phone powered off and pressing the vol up and down keys while plugging into the PC, it only enters Fastboot mode
I have tried to do it with phone off, rebooting from Crashdump mode, from fastboot and it seems that no combination allows me to do so.
I have also tried just vol up and vol down. App loaded at the flash screen, not loaded, etc.
Thanks in advance
quy said:
Hoping someone can shed some light. Rushing to root phone again to send back warranty replacement, in my haste my laptop died mid flash and now can only boot in Fastboot and Crashdump Mode.
I am attempting to restore to factory via the MSM tool but cannot for the life of me enter EDL mode.
With phone powered off and pressing the vol up and down keys while plugging into the PC, it only enters Fastboot mode
I have tried to do it with phone off, rebooting from Crashdump mode, from fastboot and it seems that no combination allows me to do so.
I have also tried just vol up and vol down. App loaded at the flash screen, not loaded, etc.
Thanks in advance
Click to expand...
Click to collapse
What I did when I was in Crash Dump Mode was,
Press and Hold Power Off and Volume Up button and release when the screen goes off. Now your phone is switched off. Now to enter the EDL mode you need to press and hold volume up and volume down buttons at the same time...and then connect the mobile to pc while still holding the buttons. Done. MSM tool will detect your phone.
NOTE : Also keep the Device Manager window open on the PC while u connect the phone to pc and check if it shows up there.
quy said:
Hoping someone can shed some light. Rushing to root phone again to send back warranty replacement, in my haste my laptop died mid flash and now can only boot in Fastboot and Crashdump Mode.
I am attempting to restore to factory via the MSM tool but cannot for the life of me enter EDL mode.
With phone powered off and pressing the vol up and down keys while plugging into the PC, it only enters Fastboot mode
I have tried to do it with phone off, rebooting from Crashdump mode, from fastboot and it seems that no combination allows me to do so.
I have also tried just vol up and vol down. App loaded at the flash screen, not loaded, etc.
Thanks in advance
Click to expand...
Click to collapse
It always seems to take me several tries to get it right. I think if I don't hit the vol +/- keys right at the exact time that's the problem. Just be patient and keep trying. The first time I did it, it took me what seemed forever. Thought maybe my phone was broken.
Sent from my IN2025 using Tapatalk
rmiles7721 said:
It always seems to take me several tries to get it right. I think if I don't hit the vol +/- keys right at the exact time that's the problem. Just be patient and keep trying. The first time I did it, it took me what seemed forever. Thought maybe my phone was broken.
Sent from my IN2025 using Tapatalk
Click to expand...
Click to collapse
I have been doing custom roms since the old win ce devices....and yet you sir have been able to make me feel like an idiot haha. Thanks for this. you had it spot on!! thanks so much
Hello Folks. So i have found myself in this situation as well. MY phone wont go off and keeps restarting to CrashDump Mode. As such can't seem to get into EDL mode inorder to flash. Any tips? I have tried all the above methods nothing seems to work. Is there a different key combination or a fastboot command i can use to achieve EDL? Help a brother i'm going nuts. Device IN2020
HaronM said:
Hello Folks. So i have found myself in this situation as well. MY phone wont go off and keeps restarting to CrashDump Mode. As such can't seem to get into EDL mode inorder to flash. Any tips? I have tried all the above methods nothing seems to work. Is there a different key combination or a fastboot command i can use to achieve EDL? Help a brother i'm going nuts. Device IN2020
Click to expand...
Click to collapse
You just need to keep trying it. Make sure you hit vol+/- at the same time and hold for a few seconds, plug in the USB cable, then let off the vol keys. It's difficult to do and get right with two hands. Recently did it again as I wanted to upgrade to the 11 beta from a clean system. Seems like it took me forever to get it this time but eventually I did.
Use usb 2.0 port.
After using 2.0 instead of 3.0 and the phone connected stable for a while (after many tries)
able to finish the msm operation successful ..
But phone not booting .. getting black screen after 1+ logo
at this point I thought to clear cache but My phone is locked I cannot use any recovery .. I cannot even go into oneplu recovery LOL .. It seems like I am doomed
For me personally I could only get it to work on USB2.0 ports. On USB3.0 it just puts me back into fastboot mode or when it does go into EDL MSM tool just fails with a communication error immediately.
I kinda bricked mine as well messing around with GSI ROM's and flashing too hastily and to the wrong partition lol.
It has always worked for me with USB 2.0 port and non oneplus cable.
originable cable would not work for me on usb 3 or USB 2 port, but 3rd party cable start immediately with USB 2 port.
I've had the issue where EDL mode works..... for a few seconds, then the phone reboots.
Very frustrating!
The MSM Download Tool does spot the phone, but since the phone seems to reboot, I don't have enough time to do anything!
Any ideas why this is happening?
OneOfThePetes said:
I've had the issue where EDL mode works..... for a few seconds, then the phone reboots.
Very frustrating!
The MSM Download Tool does spot the phone, but since the phone seems to reboot, I don't have enough time to do anything!
Any ideas why this is happening?
Click to expand...
Click to collapse
You need to already hit start on msmtool BEFORE plugging in phone
1- start MSM tool (prepare the settings and choose the right oos)
2-keep the cable connected to one end (I prefere to keep it connected from the phone side first)
3-keep holding volume up/down for 3-4 sec and connect the other end of the cable to your PC
4-your device will be connected directly stop holding volume up/down and in msm tool press start wait for ≈300 sec
5-now your device should work as it was before
OneOfThePetes said:
I've had the issue where EDL mode works..... for a few seconds, then the phone reboots.
Very frustrating!
The MSM Download Tool does spot the phone, but since the phone seems to reboot, I don't have enough time to do anything!
Any ideas why this is happening?
Click to expand...
Click to collapse
After rebooting my pc, and fiddling with drivers, I got it all sorted finally.
Thanks for your help, folks.
Niranjan Bapat said:
What I did when I was in Crash Dump Mode was,
Press and Hold Power Off and Volume Up button and release when the screen goes off. Now your phone is switched off. Now to enter the EDL mode you need to press and hold volume up and volume down buttons at the same time...and then connect the mobile to pc while still holding the buttons. Done. MSM tool will detect your phone.
NOTE : Also keep the Device Manager window open on the PC while u connect the phone to pc and check if it shows up there.
Click to expand...
Click to collapse
This is a royal pita! I remember when it used to be fun....
Anyway, I've been trying every trick in the book, and then some, but shiznit just isn't going right! The holding of the up and down buttons would be easier if this was the pixel, but it is a tad hard to not mistakenly hit the power button on the other side.
The device manager shows the Qualcomm QDLoader and the msm Downloader is showing the infamous waiting for device... I've been at it for 8 straight hours and if there was a local OnePlus store that sold the international version of the OP8P, that's where I would be heading in a few hours.... It's really frustrating to say the least.
Anyway, when I'm in the bootloader, the device manager shows the Android phone, so I'm thinking that maybe I am in the edl mode when the Qualcomm port shows up, but like I said, the msm is waiting....
tried everything and it is constantly booting into bootloader. I even tried an adjusted fastboot script to boot into EDL but it still boots into bootloader. I have booted into EDL before on a OnePlus 7T, and I have tried multiple times by pressing the OnePlus 8 pro volume buttons at the same time, but always bootloader. Just to check, I tried doing it on my OP 7T again and it worked perfectly fine. Help????
I have had to flash stock 4 times because I land in crash dump mode and it has always been a tricky situation to get into edl.
What worked for me 100% of the time was following the steps in the youtube guide below.
From 2:30 onwards
Hope it helps
I had the same issues, but fixed once read comments as per above. Let me summarize what I did:
1. installed driver Qualcomm HS-USB QDLoader 9008 (I'm using Windows 10) - driver in a cab file should be unpacked using command expand (with proper switches) to preserve folders.
2. launched MSM DT and had it configured and then pressed Verify\Start, as EDL is available only for very short time - 2-3 secs with screen turned off.
3. as my phone was stuck in booting loop I was just keeping presses Vol+/- waiting for EDL to be entered, MDM will find the phone and start uploading data.
Just don't give up trying.
quy said:
Hoping someone can shed some light. Rushing to root phone again to send back warranty replacement, in my haste my laptop died mid flash and now can only boot in Fastboot and Crashdump Mode.
I am attempting to restore to factory via the MSM tool but cannot for the life of me enter EDL mode.
With phone powered off and pressing the vol up and down keys while plugging into the PC, it only enters Fastboot mode
I have tried to do it with phone off, rebooting from Crashdump mode, from fastboot and it seems that no combination allows me to do so.
I have also tried just vol up and vol down. App loaded at the flash screen, not loaded, etc.
Thanks in advance
Click to expand...
Click to collapse
Try different ports. My usb 3 port would force it into fastboot but usb 2 was fine.
What to do if the device doesn't have any usb 2.0 port?