Reception issues between towers. - LG V20 Questions & Answers

Hi
I am having a problem when my phone is between 2 towers.
The download/upload speed slows to a crawl on both 4g and lte.
This happens even if the signal strength from each towers is high (around -80dbm).
I use network cell info to confirm this. My Wife's V20 has the same issue.
As soon as I can achieve around a 10 or better dbm difference between the towers everything speeds up again.
There are 2 locations near me where this happens (with different towers).
My other phone (a note 3) does not have this problem.
I'm on T-Mobile.
EDIT. I have also discovered this only happens on band 12.
Any ideas?
Thanks in advance.

Related

question about 2g and 3g and service

Hello All,
I just recently purchased the AT&T nexus one and I just want to make sure my understanding of my question is correct or not. I have noticed that when I am at my house and if I have 3g enabled the signal bars next to the 3g icon are somewhere between 2-4 bars and are always fluctuating, But if i enable the option for use only 2G networks obviously the H or 3g icon disappear and the EDGE icon shows up but the signal strength is at a full 5 bars all the time not fluctuating. It was my understanding that the signal strength bars were completely seperate from the 3g or 2g icons. I thought that the signal strength bars represent my cell signal and whatever icon showed up was the data coverage in the area but they aren't related? Is this correct or is it that the signal strength bars represent the signal of the 3g or 2g?
The signal strength bar represents the 2g or3g signal strength.
Both of you are correct. To make calls or text the signal bars are need to use data the icons are needed.
But you don't make calls on 3g or edge. So I don't understand why the signal strength bars are lower when on 3g as opposed to edge unless its wat the first Guy said. And that doesn't seem correct cause that's basically saying my cell service is worse and I would have a higher chance of getting dropped or no calls at all when I am on 3g as opposed to edge.
not sure about your networks but on every other 3G network you make both call and data,,,
rimrocka0834 said:
But you don't make calls on 3g or edge. So I don't understand why the signal strength bars are lower when on 3g as opposed to edge unless its wat the first Guy said. And that doesn't seem correct cause that's basically saying my cell service is worse and I would have a higher chance of getting dropped or no calls at all when I am on 3g as opposed to edge.
Click to expand...
Click to collapse
A couple of notes here:
- All you're seeing here is that 3G service is weaker than 2G/EDGE service at your house. Perhaps there are more EDGE towers around you than 3G-enabled towers, or EDGE runs on a lower frequency such as 850MHz that penetrates through walls better.
- If your 3G service completely drops out, you should fall back to EDGE during the call. There shouldn't be any interruption, but there's a small chance that the call will drop when this happens.
The latter happens to me on TMO all the time if I go into weak 3G, and I've never had a dropped call or issue because of it - so really, as long as you have solid EDGE service, phone calls shouldn't be a problem for you. Note that when you fall back to EDGE, you can't use data while on the call, but if you're still on 3G, it's possible to do so. You can of course combat by this by just using wifi.
Now, on the other hand, AT&T's 3G network is overloaded in some markets, so you may have a dropped call because of that - but that's a different issue altogether.
gsvnet thanks a lot! Cleared up everything I was wondering.

cdma signal preference

I know its kind of against how cellular is designed to work but I am in a situation where a sprint signal is only barely(0 bars) available and it decides to roam (with the triangle) to a uscellular signal. The problem is that its constantly trying to stay on the sprint signal, realizing that the connection isn't good enough and goes back to the uscellular signal and is just killing performance and battery. Is there any prl update or fix I can make with the evo to just stay on the uscc signal and forget about the crappy sprint signal at this location instead of hopping between the two? Ideally I'd like something automatic but I would even settle for a toggle. The uscellular signal is a repeater that was installed at my workplace. For example, in battery status my evo; the cell standby is at 39%
I am having the EXACT same issue in my office. The repeater signal in my office (850 MHz so it only repeats Verizon / AT&T / T-Mobile) is -70 dBm (full bars on my phone). The Sprint signal from outside through the foot thick cement walls is -102 or worse dBm (aka 1-0 bars). Why the hell will the phone not consistently stay on the higher power signal??
The techknowfile trick is NOT the solution to this problem. This seems like a problem with the phone itself - the whole point of a multi-band phone with free roaming is it should always pick the best signal (in my opinion).
I tried the techknowfile trick as well with no luck. Maybe a different prl? I used the 40060.prl file suggested.

[Q] Sporadic Signal Loss

Okay so i've got an aria rooted and flashed with the Liberated 2.2 rom. I've been using it for the past 3 months and I've noticed that I will go from full service while a phone call is comming in and complete signal loss when I answer it. I have set the phone on a table and watched the network signal strength go from -113 dBm and 0asu to -81 dBm and 16asu and vise versa. I have also noticed that when I lose signal my "H" for the data goes with it and service comes back a few seconds later very strong but showing "G". From there it will go to "E" then back to "H".
Could anyone explain this or have a better reason as to why this is happening? Maybe its just based on the connection where I live but I've used the app Antennas and the tower is about 1/3 mile away.
Any info or help would be awesome
Thanks
i'm not sure why this would happen outside of a poor bit of service where you're living.
i used the various roms for the aria and never had any sort of service loss issue.
as far as the icons switching around, e = edge network (2g), h = hspa (3g). when your phone drops its connection, it tries to reconnect as fast as possible, usually with edge, then after its strong it looks for the 3g connection.

[Q] 24A/12B modem issues,weak signal on 3G GSM

I have VS980 outside the US, set to GSM/UMTS and my signal goes as height as 2/5 most of the time, rarely 3/5 and the highest I've seen in 4 days was 4/5, all in different places. I experience no disconnections and the network speed is just ok , goes up to 5700down/1300up which is almost regular speed I was used to get with my xiaomi mi2s.
So can it be just a wrong presentation of the signal strength when on GSM network?
Can I flash radio from D802?
Thanks.

Signal problem theory/research

Hello, i live in a relatively small town where my service provider has very poor 4G signal. but pretty good 3G signal. With the Axon 7 i have a lot of signal problems that i didnt have with any of my previous phones, where outdoor signal is pretty bad and indoor signal is almost unusable. It also connects almost exclusively to 4G, and in contrast all of my previous phones connected almost exclusively to 3G. Over the last weekend i traveled to a major city where my service provider has very strong 4G signal, and the signal problem was almost non existant. I even had signal in places where other people with the same service provider did not. So my theory is the following, assuming that the hardware (antenna) used for 4G and 3G is the same, it may not be a hardware problem, but a problem with the software having a hard time knowing which band/signal it should connect to. It seems that in my case it prioritizes 4G signal and the cost of a VERY unstable cellphone service. This is also assosiated with the fact that when it connects to 3G (incredibly rare), the phone goes inmediately from 1/2 bars to 4/5 bars. I also changed the SIM configuration to leave LTE out, but either for a visual bug or a software bug, it keeps connecting only to 4G. So could this be the problem that me and a lot of people in low 4G signal zones are having? Is there anyway i can force the phone to connect exclusivly to the 3G signal to test if that is indeed the problem?
Regards!
Nehuen said:
Hello, i live in a relatively small town where my service provider has very poor 4G signal. but pretty good 3G signal. With the Axon 7 i have a lot of signal problems that i didnt have with any of my previous phones, where outdoor signal is pretty bad and indoor signal is almost unusable. It also connects almost exclusively to 4G, and in contrast all of my previous phones connected almost exclusively to 3G. Over the last weekend i traveled to a major city where my service provider has very strong 4G signal, and the signal problem was almost non existant. I even had signal in places where other people with the same service provider did not. So my theory is the following, assuming that the hardware (antenna) used for 4G and 3G is the same, it may not be a hardware problem, but a problem with the software having a hard time knowing which band/signal it should connect to. It seems that in my case it prioritizes 4G signal and the cost of a VERY unstable cellphone service. This is also assosiated with the fact that when it connects to 3G (incredibly rare), the phone goes inmediately from 1/2 bars to 4/5 bars. I also changed the SIM configuration to leave LTE out, but either for a visual bug or a software bug, it keeps connecting only to 4G. So could this be the problem that me and a lot of people in low 4G signal zones are having? Is there anyway i can force the phone to connect exclusivly to the 3G signal to test if that is indeed the problem?
Regards!
Click to expand...
Click to collapse
Without knowing which model Axon 7 you are using, where you are using it, and who your provider is, there is little anyone can do to help you. All I can say is that it helped me A LOT to go into settings and turn off
VoLTE.
tabletalker7 said:
Without knowing which model Axon 7 you are using, where you are using it, and who your provider is, there is little anyone can do to help you. All I can say is that it helped me A LOT to go into settings and turn off
VoLTE.
Click to expand...
Click to collapse
U model last update, using it from Argentina, and the provider is Claro. I have LTE disabled in SIM confg as i already said and VoLTE turn of as well but the phone keeps connecting to 4G no matter what i do, even if i configure it to only GSM
I don't think its a matter of position or provider (version could be if different software is provided), but a general issue with the phone and band/signal interpretation coupled with the apparent innability to go off 4G
Refards!
Nehuen said:
U model last update, using it from Argentina, and the provider is Claro. I have LTE disabled in SIM confg as i already said and VoLTE turn of as well but the phone keeps connecting to 4G no matter what i do, even if i configure it to only GSM
I don't think its a matter of position or provider (version could be if different software is provided), but a general issue with the phone and band/signal interpretation coupled with the apparent innability to go off 4G
Refards!
Click to expand...
Click to collapse
ok when it connects to LTE it says "4G LTE". The 4G that you are getting is probably HSPA or something. And we had someone on here a few months back using Claro in Argentina and they had to seek answers from their Claro
tabletalker7 said:
ok when it connects to LTE it says "4G LTE". The 4G that you are getting is probably HSPA or something. And we had someone on here a few months back using Claro in Argentina and they had to seek answers from their Claro
Click to expand...
Click to collapse
If "4G LTE" is 4G and "4G" is HSPA, when only a "G" appears, what band am i connecting too? Its still pretty weird that im having major signal issues in my town, but when i go to a big city my signal is even better than other phones, it seems inconsistent with the whole "bad hardware" theory. I talked to Claro and it seemed like from their end it was a non issue, can you point me to the thread to see if he got it fixed somehow?
Regards!
Nehuen said:
If "4G LTE" is 4G and "4G" is HSPA, when only a "G" appears, what band am i connecting too? Its still pretty weird that im having major signal issues in my town, but when i go to a big city my signal is even better than other phones, it seems inconsistent with the whole "bad hardware" theory. I talked to Claro and it seemed like from their end it was a non issue, can you point me to the thread to see if he got it fixed somehow?
Regards!
Click to expand...
Click to collapse
/Trolling a bit/
I'm always LMAO when I hear US people talking about that 4G scam (which is H+ for real btw)
G is for 2G
E is for 2G+
3G is 3G
H is 3G+
H+ is 3G++ (an intermediary protocol up to 42MBps)
4G is LTE (up to 150Mbps in the EU most of the time)
4G+ is LTE-A (which is available in most of the EU, SK & JP) - up to 600Mbps, 200MBps in most tests
I've not heard of an app that could modify the way the phone "clings" to 4G LTE, since that might likely be the modem firmware doing it on its own.
RedWave31 said:
/Trolling a bit/
I'm always LMAO when I hear US people talking about that 4G scam (which is H+ for real btw)
G is for 2G
E is for 2G+
3G is 3G
H is 3G+
H+ is 3G++ (an intermediary protocol up to 42MBps)
4G is LTE (up to 150Mbps in the EU most of the time)
4G+ is LTE-A (which is available in most of the EU, SK & JP) - up to 600Mbps, 200MBps in most tests
I've not heard of an app that could modify the way the phone "clings" to 4G LTE, since that might likely be the modem firmware doing it on its own.
Click to expand...
Click to collapse
Then this is even weirder, because is G is not 3G, but 2G it means that the phone NEVER connects to the major band that all of my previous phones and Claro users connect to. Is there anyway to force to only connect to 3G?
Regards!
i have the G european model, in my town i have bad lte signal 1/2bar, when with my previously xiaomi mi4c was got 4/5 bars (maximum). In the big town i have got in the most of cases 4/5 bars. I think the "signal problems" are relatives of a lack of somehow software. i told this because i've read with the china model with the last updates an improvement of the signal reception of the phone.
Nehuen said:
Then this is even weirder, because is G is not 3G, but 2G it means that the phone NEVER connects to the major band that all of my previous phones and Claro users connect to. Is there anyway to force to only connect to 3G?
Regards!
Click to expand...
Click to collapse
You can however force a specific protocol indeed, but you will lack the ability to autoswitch networks. Just download 4G LTE Switch (here) which is a glorified secret code dialer. Just click on prefered network and change at your convenience (4G LTE only, WCDMA only - H+ - and so on). Remember that if you force 4G LTE in an area in which you have no coverage, you won't have internet, and no 2G/3G fallback (so no texts, no calls)
I don't know if this is the same problem, but my wife has an iPhone 6+ and I have an A2017U on B29 stock root. We both use the same network (Movistar Mexico) and while her iPhone often registers LTE, my A7 often registers 4G or even E in the same place. The A7 is receiving the same bands but appears to be "choosing" or locking into the slower protocols more often.
EDIT: NEVER MIND… an xposed module was messing with my network settings. Fixed it. Now I get LTE right away.
nuserame said:
EDIT: NEVER MIND… an xposed module was messing with my network settings. Fixed it. Now I get LTE right away.
Click to expand...
Click to collapse
Which module?
What if flash any Custom OS?Would it give better signal ?

Categories

Resources