Related
Hey guys, I have a A2017 axon 7, and I tried to upgrade from Marshmalow to nougat by flashing the B04 update from TWRP. I have now the factory recovery mode, and when I try to go in fastboot, it tries to launch the bootloader( which just tells me that my device software cannot be checked for corruption and that I need to lock my bootloader). When I try to boot normally it stays on the same "bootloader screen" and tells me to press the start button which makes the phone display the linux logo.... I'm a bit lost, I'm on ArchLinux could you pls help me ?
Thx !
Dr_Raider said:
Hey guys, I have a A2017 axon 7, and I tried to upgrade from Marshmalow to nougat by flashing the B04 update from TWRP. I have now the factory recovery mode, and when I try to go in fastboot, it tries to launch the bootloader( which just tells me that my device software cannot be checked for corruption and that I need to lock my bootloader). When I try to boot normally it stays on the same "bootloader screen" and tells me to press the start button which makes the phone display the linux logo.... I'm a bit lost, I'm on ArchLinux could you pls help me ?
Thx !
Click to expand...
Click to collapse
Well, you should use MiFlash and install the stock system through EDL. The problem is that MiFlash is for Windows x64. if you could get a win10 x64 pc, you could fix it in a minute.
Or get to the recovery if you can, and flash Nougat again but via an SD card. But maybe you won't be able to get to the recovery mode
Choose an username... said:
Well, you should use MiFlash and install the stock system through EDL. The problem is that MiFlash is for Windows x64. if you could get a win10 x64 pc, you could fix it in a minute.
Or get to the recovery if you can, and flash Nougat again but via an SD card. But maybe you won't be able to get to the recovery mode
Click to expand...
Click to collapse
I need help! I wanted to relock the bootloader but then I coulnd't enter the recovery or fastboot anymore. When I press any combination it always turn on for 1 sec and then the screen turns off again but it still GOT recognized as QUSB Bulk. After I installed MiFlash the device is recognized as QDLOADER 9008. I didn't flash anything and I don't kno how to unbrick my device now .
I use the A2017G model btw.
Kantastisch said:
I need help! I wanted to relock the bootloader but then I coulnd't enter the recovery or fastboot anymore. When I press any combination it always turn on for 1 sec and then the screen turns off again but it still GOT recognized as QUSB Bulk. After I installed MiFlash the device is recognized as QDLOADER 9008. I didn't flash anything and I don't kno how to unbrick my device now .
I use the A2017G model btw.
Click to expand...
Click to collapse
How did you relock the bootloader? If you used a guide, you should have found a warning, and if you used axon7toolkit a message should've popped up.
You messed up. Real bad. You are probably on DFU mode, and the only ways to get out of there are:
-discharge the battery completely and try to enter FTM mode (i think you have to do that while it is connected to a PC), I think it was with volume down + power. this method works for very few people. If you enter ftm mode, issue 'adb reboot edl' and use MiFlash right away with a FULL_EDL package
-use the 4th category brick repair manual (disassemble the phone, short some pins)
Choose an username... said:
How did you relock the bootloader? If you used a guide, you should have found a warning, and if you used axon7toolkit a message should've popped up.
You messed up. Real bad. You are probably on DFU mode, and the only ways to get out of there are:
-discharge the battery completely and try to enter FTM mode (i think you have to do that while it is connected to a PC), I think it was with volume down + power. this method works for very few people. If you enter ftm mode, issue 'adb reboot edl' and use MiFlash right away with a FULL_EDL package
-use the 4th category brick repair manual (disassemble the phone, short some pins)
Click to expand...
Click to collapse
I think DFU Mode is when I get recognized as ZTE Handset diagnostic .... according to this guide : https://forum.xda-developers.com/axon-7/how-to/a2017-4th-category-brick-repair-manual-t3585898) It's a2017 but still.
"Axon 7 restore manual from bricked conditions when only ZTE Handset Diagnostic Interface(DFU) (COM...) mode is detected"
But I get recognized as QDloader 9008 and miflash also recognizes it as com10 or something.
Kantastisch said:
I think DFU Mode is when I get recognized as ZTE Handset diagnostic .... according to this guide : https://forum.xda-developers.com/axon-7/how-to/a2017-4th-category-brick-repair-manual-t3585898) It's a2017 but still.
"Axon 7 restore manual from bricked conditions when only ZTE Handset Diagnostic Interface(DFU) (COM...) mode is detected"
But I get recognized as QDloader 9008 and miflash also recognizes it as com10 or something.
Click to expand...
Click to collapse
it's not necessarily like that. DFU mode is just a mode in which the phone can be. Sometimes Windows just installs the QDLoader driver even though it's not EDL. and if you tried miflash and it didn't work, then it's most probably that.
There's a way to check. If you go to Properties, there should be a number that identifies the mode. if you google it and 'dfu interface' appears, then you are dfu-bricked
But if you locked the bootloader without being fully stock then it's most probably dfu bricked anyways
Again, how did you lock the bootloader?
I don't actually know if I really locked the bottloader.
So, I had unlocked bootloader and twrp. I just bootet into the bootloader, typed "fastboot oem lock" in adb and it said OK on the PC.
But on the phone it never asked me if I want to lock it or anything. And I never said MiFlash isn't working. It recognizes my phone but i judt didn't TRY to flash anything because I didn't want to make the situation even worse perhaps
Choose an username... said:
it's not necessarily like that. DFU mode is just a mode in which the phone can be. Sometimes Windows just installs the QDLoader driver even though it's not EDL. and if you tried miflash and it didn't work, then it's most probably that.
There's a way to check. If you go to Properties, there should be a number that identifies the mode. if you google it and 'dfu interface' appears, then you are dfu-bricked
But if you locked the bootloader without being fully stock then it's most probably dfu bricked anyways
Again, how did you lock the bootloader?
Click to expand...
Click to collapse
I don't actually know if I really locked the bottloader.
So, I had unlocked bootloader and twrp. I just bootet into the bootloader, typed "fastboot oem lock" in adb and it said OK on the PC.
But on the phone it never asked me if I want to lock it or anything. And I never said MiFlash isn't working. It recognizes my phone but i judt didn't TRY to flash anything because I didn't want to make the situation even worse perhaps
Kantastisch said:
I don't actually know if I really locked the bottloader.
So, I had unlocked bootloader and twrp. I just bootet into the bootloader, typed "fastboot oem lock" in adb and it said OK on the PC.
But on the phone it never asked me if I want to lock it or anything. And I never said MiFlash isn't working. It recognizes my phone but i judt didn't TRY to flash anything because I didn't want to make the situation even worse perhaps
Click to expand...
Click to collapse
Lol it doesn't ask you if you want to lock it, that's the point with bootloader mode. there's no system, no UI, and you make stuff via commands.
This is why you shouldn't even attempt this kind of stuff without knowing how it works. At least if you had used axon7toolkit, it would've told you not to.
Find a FULL_EDL package for your model. If you have an A2017, simply use this one:
https://androidfilehost.com/?fid=817550096634790942
or
https://mega.nz/#!JqwEUDCa!lW3NDaBNbmMxhtw6XajspHBJaaEmLC8uNvMZS5ww0EQ
(they are the same file)
Unzip it, leave the folder somewhere handy, put the phone in what you believe is EDL, open MiFlash and select the folder, and flash
Choose an username... said:
Lol it doesn't ask you if you want to lock it, that's the point with bootloader mode. there's no system, no UI, and you make stuff via commands.
This is why you shouldn't even attempt this kind of stuff without knowing how it works. At least if you had used axon7toolkit, it would've told you not to.
Find a FULL_EDL package for your model. If you have an A2017, simply use this one:
https://androidfilehost.com/?fid=817550096634790942
or
https://mega.nz/#!JqwEUDCa!lW3NDaBNbmMxhtw6XajspHBJaaEmLC8uNvMZS5ww0EQ
(they are the same file)
Unzip it, leave the folder somewhere handy, put the phone in what you believe is EDL, open MiFlash and select the folder, and flash
Click to expand...
Click to collapse
Yeah, I screwed up, I know. But what is the point of flashing a full edl package for the phone if I have to put the phone in "what I believe id edl mode"?
And what shall I do if I succeed at something? Besided that, I can't find any EDL package for the A2017G?
https://forum.xda-developers.com/axon-7/development/edl-emergency-dl-mode-twrp-unlock-t3553514
This guide tells me NOT TO flash anything on a2017g...
Kantastisch said:
Yeah, I screwed up, I know. But what is the point of flashing a full edl package for the phone if I have to put the phone in "what I believe id edl mode"?
And what shall I do if I succeed at something? Besided that, I can't find any EDL package for the A2017G?
https://forum.xda-developers.com/axon-7/development/edl-emergency-dl-mode-twrp-unlock-t3553514
This guide tells me NOT TO flash anything on a2017g...
Click to expand...
Click to collapse
Okay let me tell you this real straight. I have done this. I have the G packages, I just thought you were the op for some reason. Look at the back of the phone and confirm whether you have an A2017G or an A2017 just in case, or you might mess up even more, as hard as that can be.
at any rate, your fears are all dumbfounded, because in the situation that you are in, you have 3 options:
a) disregard all the help that i'm trying to give you, even though I have already done the process; and keep your brick on a shelf.
b) search on google or xda yourself, then do the process, without bothering here with your lack of trust
c) follow my advice and do the damn process
Whichever option you choose, I'm gonna leave the package here:
https://mega.nz/#!UrxCRCrQ!a4sXVFu5oqct2sWStfN_luGpN5HEGXxE4FcrRteagQ4
or
https://androidfilehost.com/?fid=961840155545591863
Again, I HAVE FOLLOWED THE 4TH CATEGORY BRICK REPAIR GUIDE AND FIXED MY G. I flashed stuff through EDL at least 10 times. And there wouldn't be a bunch of EDL packages for the G if they had a 100% chance of bricking your phone
So. If you decide to do this, turn your phone off. connect the USB cable to the PC but not the phone. Hold both volume buttons (but not the power button) and insert the USB cable at the same time. Then fire up MiFlash and try to flash the file (you have to unzip the folder, then select the folder on miflash, then flash. Here 2 things may happen:
a) it flashes and you can just go bother someone else
b) it doesn't and you have to follow the 4th category brick repair guide
Simple as that. if it fails, you might want to check if the 'Qualcomm HS-USB QDLoader 9008' is actually EDL mode or DFU mode, so you can do that by going to properties and checking some device identifier number on google (haven't done that, i just read that it can be done somewhere here).
Choose an username... said:
Okay let me tell you this real straight. I have done this. I have the G packages, I just thought you were the op for some reason. Look at the back of the phone and confirm whether you have an A2017G or an A2017 just in case, or you might mess up even more, as hard as that can be.
at any rate, your fears are all dumbfounded, because in the situation that you are in, you have 3 options:
a) disregard all the help that i'm trying to give you, even though I have already done the process; and keep your brick on a shelf.
b) search on google or xda yourself, then do the process, without bothering here with your lack of trust
c) follow my advice and do the damn process
Whichever option you choose, I'm gonna leave the package here:
https://mega.nz/#!UrxCRCrQ!a4sXVFu5oqct2sWStfN_luGpN5HEGXxE4FcrRteagQ4
or
https://androidfilehost.com/?fid=961840155545591863
Again, I HAVE FOLLOWED THE 4TH CATEGORY BRICK REPAIR GUIDE AND FIXED MY G. I flashed stuff through EDL at least 10 times. And there wouldn't be a bunch of EDL packages for the G if they had a 100% chance of bricking your phone
So. If you decide to do this, turn your phone off. connect the USB cable to the PC but not the phone. Hold both volume buttons (but not the power button) and insert the USB cable at the same time. Then fire up MiFlash and try to flash the file (you have to unzip the folder, then select the folder on miflash, then flash. Here 2 things may happen:
a) it flashes and you can just go bother someone else
b) it doesn't and you have to follow the 4th category brick repair guide
Simple as that. if it fails, you might want to check if the 'Qualcomm HS-USB QDLoader 9008' is actually EDL mode or DFU mode, so you can do that by going to properties and checking some device identifier number on google (haven't done that, i just read that it can be done somewhere here).
Click to expand...
Click to collapse
THANKS SO MUCH , you saved my ass, it flashed without a problem and sorry for bothering you. Bootloader is locked now and it works fine. Thanks again!
My problem is that I can't even try to do the procedure in the other threads that i've read because my pc simples dont recognize anything when i install the qualcomm drivers. Any tips? Thank you in advance. I want to try this thread [GUIDE][QFIL MODE]Unbrick your Le Pro3, tested and working. But simply the qualcomm port doesnt appear in the device manager.
Bad cable or need to reinstall drivers...
marik1 said:
Bad cable or need to reinstall drivers...
Click to expand...
Click to collapse
I tried with two different cables and reinstalled the drivers a few times now. No port in the device manager. Just the Android ADB Interface tha showed when I installed the leeco adb drivers. On the ports just appear the standard Comunication port and printer port. I tried everything, the volume bottons power, etc. The Flash One dont recognize the phone for QFIL.
Say sth more about your phone state and history...
marik1 said:
Say sth more about your phone state and history...
Click to expand...
Click to collapse
I dont have hardware problems. I flashed the Pixel Experience rom in february with sucess but I didnt like it. It had too much battery drain. Then I wanned to try some other rom like AICP. But in the process of flashing something went wrong. I wasnt able to flash it, always gave me the error 7. Then it simply died. I was rebooting TWRP mode and it went dead. Now just vibrates when I try to turn on. I tried the QFIL process (both volumes + power) but I dont even know. How can we know that it in qfil mode? My pc wont recognize anything. Not in Flash One, Not in QPST, nothing. Am I doing something wrong? The phone vibrates so its charged. I installed the Qualcomm drivers properly, I thing, eventhow it doesnt appear the qualcomm 9008 port in the device manager. Its suppose to appear before the phone is pluged right? Thank you for the reply.
I've no idea how to help you... Sorry.
gradim said:
I dont have hardware problems. I flashed the Pixel Experience rom in february with sucess but I didnt like it. It had too much battery drain. Then I wanned to try some other rom like AICP. But in the process of flashing something went wrong. I wasnt able to flash it, always gave me the error 7. Then it simply died. I was rebooting TWRP mode and it went dead. Now just vibrates when I try to turn on. I tried the QFIL process (both volumes + power) but I dont even know. How can we know that it in qfil mode? My pc wont recognize anything. Not in Flash One, Not in QPST, nothing. Am I doing something wrong? The phone vibrates so its charged. I installed the Qualcomm drivers properly, I thing, eventhow it doesnt appear the qualcomm 9008 port in the device manager. Its suppose to appear before the phone is pluged right? Thank you for the reply.
Click to expand...
Click to collapse
Instead of creating a new post why not just read the enormous unbrick forums that exists and have proven steps. Many, Many phones have been debricked using those steps.
Hint, read the last pages for updated links to the software tools needed.
Next, I just found this cable which will help immensely with unbricking your device: https://www.amazon.com/GPG-EDL-Cabl...r1&keywords=edl+cable+for+wall+qualcomm+usb+c
tsongming said:
Instead of creating a new post why not just read the enormous unbrick forums that exists and have proven steps. Many, Many phones have been debricked using those steps.
Hint, read the last pages for updated links to the software tools needed.
Next, I just found this cable which will help immensely with unbricking your device: https://www.amazon.com/GPG-EDL-Cabl...r1&keywords=edl+cable+for+wall+qualcomm+usb+c
Click to expand...
Click to collapse
I've tried four different cables now and nothing. Thank you for minding but I think there isn't a solution for my leeco. Its dead and no one can help him.
Is yours 722?
Sent from my SM-A730F using xda premium
mchlbenner said:
Is yours 722?
Sent from my SM-A730F using xda premium
Click to expand...
Click to collapse
No, x720 6gb ram 64 rom.
gradim said:
No, x720 6gb ram 64 rom.
Click to expand...
Click to collapse
Is your phone completely Dead or do you have fashboot or anything working.
Do have a red flashing light?
Sent from my SM-A730F using xda premium
mchlbenner said:
Is your phone completely Dead or do you have fashboot or anything working.
Do have a red flashing light?
Sent from my SM-A730F using xda premium
Click to expand...
Click to collapse
Completely dead, just vibrates when I press power and yes, I sometimes have the red light, sometimes flashing, sometimes stable.
gradim said:
I dont have hardware problems. I flashed the Pixel Experience rom in february with sucess but I didnt like it. It had too much battery drain. Then I wanned to try some other rom like AICP. But in the process of flashing something went wrong. I wasnt able to flash it, always gave me the error 7. Then it simply died. I was rebooting TWRP mode and it went dead. Now just vibrates when I try to turn on. I tried the QFIL process (both volumes + power) but I dont even know. How can we know that it in qfil mode? My pc wont recognize anything. Not in Flash One, Not in QPST, nothing. Am I doing something wrong? The phone vibrates so its charged. I installed the Qualcomm drivers properly, I thing, eventhow it doesnt appear the qualcomm 9008 port in the device manager. Its suppose to appear before the phone is pluged right? Thank you for the reply.
Click to expand...
Click to collapse
Your phone is probably fixable.
Based on what you stated above, it seems that you downloaded and attempted to install the wrong version of TWRP and now your phone has no recovery at all.
Here is partial instructions I posted in the unbricking forum : https://forum.xda-developers.com/showpost.php?p=76100899&postcount=121
Use those instructions along with is mentioned below. I have personally helped so many people unbrick their phone that I have lost track and this is the reason why the posts are so long and extensive. Because sometimes what works for one person does not work for the next. So I have essentially have taken everyone's great advice and updated the links, made the instructions steps a little more concise and easier to read, fixed some incorrect steps or added the needed skipped steps. Plus added my own research into what I believe is now a definitive guide for unbricking the Leeco variants X720 and X727. The point of not reposting the information here is to keep everything from becoming more fragmented.
Yes, it's possible that you have a hardware issue. But, its also possible that it can be fixed!
Remember that you will not see the port unless you are in EDL mode
Just press volume △ (+) and volume ▽ (–) buttons together while powering the phone on.
It should now be EDL mode. If you cannot get into EDO mode, you cannot do anything else.
If you get an error, press and hold the power button while at the same time hold vol up + and down simultaneously plug the usb cord into the back of the computer while holding the buttons.
Yes, It's a pain and this is why the deep flash cable is handy....it's a special cable ( so your extra cables will do nothing to help you) The deep flash cable will automatically put your phone into EDL mode and allow you to use Flash on.
Install the Qualcomm QDLoader 9008 driver: https://goo.gl/9E3bKq or the from links provided in the unbrick forum.
There are multiple versions or Qfil, some have issues. I posted the correct one that works.
FOR anything else go to that forum read my and everyone else's posts. Again, I keep all of my linked files are up to date, and many are located on my own drives.
You can make one of these cables. Here's a video that shows you how:
https://www.youtube.com/watch v=kSiGsYK66gM&lc=z220yhtqvwyyct21pacdp432sh2xjecek10dae1jen5w03c010c.1524884617336803
it will not be a quick fix.
There are 4 or 5 different unbricking options and it requires persistence and patience.
The good news is that your phone has a solution that may work.
So when your where flashing a rom you got error 7 and your phone went dead.
I had gotten that same error.
Error could mean two things 1) update recovery or update firmware.
My point is sounds nice like hardware issue.
These phones are known for just dieing.
Also getting into that mode you have to push power+volume+volume- at the same time.
Sent from my SM-A730F using xda premium
Hello everybody,
First off, I hate people who don't search on google before making a post, I have been searching for 4 days and I feel that it's appropriate to ask now.
I will make 2 parts to this thread, one will be a very fast explanation of what I did and the second part will be the same but a very thorough with a step by step process of what I messed up...
TL;DR: I was tired, late in the evening I flashed for some reason a Partition table of a Mi Note 3 on my Mi A1... I am now bricked and cannot access anything, fastboot, ADB, recovery nothing! I guess my phone is in EDL mode cause when I plug it in it flashes its led. "Qualcomm HS-USB QDLoader 9008" Is what I see in my device manager.
What do? oh, I forgot! I cannot access anything through any combination of buttons. I am stuck here, where I am!
The full thorough explanation for people who are bothered to read fully. (Includes my excuses for making noob mistakes, might be fun to read idk.)
Young me on a Sunday evening decides to reinstall magisk but this time with twrp cause I did it without twrp (yeah yeah I know). I was left without OTA's and after uninstalling anything that had something to do with Xposed or magisk I trashed it all. and stupid me thought that maybe? maybe? just maybe deleting Dalvik Cache would help me get my OTA's back after injecting my original ROM. This is where the fun begins.
I was not wanting to go through reinstalling magisk and all that to wipe the Dalvik Cache, I thought that that was my mission now, so I decided to search for methods that don't require root or being in the system, so some kind of fastboot or ADB command or something idk. I tried installing twrp and without my understanding that failed miserably and then I read some post where someone said that they flashed a mi note 3 partition table on their phone and something worked. Being the naïve little boii that I am, let's do that hey? Bam! bricked! I read somewhere I can open the phone and remove the battery and not having the tools is a mess, having to ask friends for some and voiding my warranty for something that probably won't work and after reading I understood that I'm in "EDL 9008 recovery" or something like that. I cannot boot into anything, I only have EDL 9008 to work with. I tried using Xiaomi's flasher tool and it would never respond to the initial hello packet (duuhh! I can't use ADB nor fastboot).
I know that this was stupid, I know! I learnt my lesson. If there is nothing we can do can I at least somehow get my internal storage data back? I deleted the backups from google drive for a short amount of time but randomly 5hrs prior to this sad story. All I have safe are now my contacts.
I hope you guys have some ideas! I feel like I'm fked but maybe with EDL 9008, there is a little glimmer of light?
P.S. If you guys somehow get me into fastboot I can flash a correct partition table back. My PC has all drivers so I can do this!
Sincerely, Micheal.
There is a way although i did tried it yet.
First of all sorry for my English.
Download latest MiFlash tool and qualcomm driver, this package contain both but not latest MiFlash so you should download lastest version from official site.
https://www.fshare.vn/file/H3R8M6OMRP2R
Download lastest stock rom.
You will need a good USB type C cable, dont use the one come with phone because you dont want to cut it in half.
Yes, that exactly what i said. Cut it in half, there are 4 small wire (or maybe 5 with type C?), remove it outer plastic and reconnect them.
Join the green and black cable, like you short circuit them, then plug your phone into PC with that cable without release green and black, wait for 5 sec then seperate them, the green and black.
Check device manager on your PC, you should hear device connect sound and qualcomm HS-USB QDLoader show up under Ports.
Open MiFlash and try to flash it.
You may want to check this video, although it in Vietnamese but you should understand the usb cable part.
https://www.youtube.com/watch?v=d5-1I9rWTiw
Hi, interesting situation. What about following this guide: http://en.miui.com/thread-235865-1-1.html ?
Its for some other phone, but try instaliing some drivers and you may get some signal of life.
Very interesting
I have thought about doing this as I had an old type-c lying around that came with the phone (I use a beautiful cable I bought off amazon) and saw this method to flash but never tried it..
I'll give it a go thanks.
btw. Your English is good I understood everything
The second comment from TrueMS:
I already have all drivers installed and in the long post I said that I have a flashing led that indicates that i'm in EDL 9008, the phone isn't dead but it won't turn on with any driver
m1shka said:
Very interesting
I have thought about doing this as I had an old type-c lying around that came with the phone (I use a beautiful cable I bought off amazon) and saw this method to flash but never tried it..
I'll give it a go thanks.
btw. Your English is good I understood everything
The second comment from TrueMS:
I already have all drivers installed and in the long post I said that I have a flashing led that indicates that i'm in EDL 9008, the phone isn't dead but it won't turn on with any driver
Click to expand...
Click to collapse
Yes, thats what I meant. Well, I dont know how to help you, wish you luck. I remember how I flashed wrong ROM for my S3 Mini and it was completly trashed, I'm glad that Xiaomi gives us at least some signs of life and hope.
And btw. I would rather charge the phone somehow - I hope it charges even in EDL mode, because if your phone dies while flashing with MiFlash, things can be even worse.
EDIT: I also found this guide, you can try it out: https://forum.xda-developers.com/g4/general/guide-unbrick-via-external-sdcard-qfil-t3748946
Okay so now a major reply!
I have stated in the OP that I am already in EDL, there is no need for cutting the cable or installing any driver, I am in EDL 9008 I don't need to "try to get there" as i'm already there.
These guides failed miserably as I have already tried them, my phone "doesn't receive a hello packet" from my phone, as I can't use adb or fastboot, or recovery.
I'll download linux and give that usb method a go then
m1shka said:
Okay so now a major reply!
I have stated in the OP that I am already in EDL, there is no need for cutting the cable or installing any driver, I am in EDL 9008 I don't need to "try to get there" as i'm already there.
These guides failed miserably as I have already tried them, my phone "doesn't receive a hello packet" from my phone, as I can't use adb or fastboot, or recovery.
I'll download linux and give that usb method a go then
Click to expand...
Click to collapse
Wish you luck:
Something that is never mentioned is to disable driver enforcement, this time hello packet was successfully recieved and flashed... Hold your happiness, cause now EDL no longer works so I can't see it in any com port and i'm certainly still in edl cause of the flashing led. Only difference I see is that now the led flashes when I hold the power button??? hmmmmmmm
To clarify:
Can't boot
Device was flashed successfully
Com port on pc can no longer see phone even after reboot
adb still don't work (proves again i'm in edl)
I'm in an even stickier situation now, can't access with my pc hmmmm..
m1shka said:
Something that is never mentioned is to disable driver enforcement, this time hello packet was successfully recieved and flashed... Hold your happiness, cause now EDL no longer works so I can't see it in any com port and i'm certainly still in edl cause of the flashing led. Only difference I see is that now the led flashes when I hold the power button??? hmmmmmmm
To clarify:
Can't boot
Device was flashed successfully
Com port on pc can no longer see phone even after reboot
adb still don't work (proves again i'm in edl)
I'm in an even stickier situation now, can't access with my pc hmmmm..
Click to expand...
Click to collapse
did you try to hold more than 30 second ? and also , do you have flash log ?
m1shka said:
Something that is never mentioned is to disable driver enforcement, this time hello packet was successfully recieved and flashed... Hold your happiness, cause now EDL no longer works so I can't see it in any com port and i'm certainly still in edl cause of the flashing led. Only difference I see is that now the led flashes when I hold the power button??? hmmmmmmm
To clarify:
Can't boot
Device was flashed successfully
Com port on pc can no longer see phone even after reboot
adb still don't work (proves again i'm in edl)
I'm in an even stickier situation now, can't access with my pc hmmmm..
Click to expand...
Click to collapse
So did you flash official stock ROM? Because I dont understand why doesnt it work... btw. when you flashed the ROM, did you lock bootloader?
Cant be battery dead?
If you are on "Qualcomm HS-USB QDLoader 9008" you will be able to flash stock fastboot firmware. Flash it using MiflashTool. Normally Miflashtool will recognized it as COMXX, where XX is the number of the port.
It's the official rom for the march ota.
The phone works, apparently it was encrypting everything... and now as I interrupted it, the encrypting failed and I lost all my data.....
Phone works but could have been better.
Before I reset the phone to factory, as i cannot use it yet, is there any way to get anything personal back? or is it gone gone and just factory reset?
What I see after boot, the phone resets every minute
https://drive.google.com/file/d/13sARZzlf3vJZK6Mx4hil6lsXRUl7-r-K/view?usp=sharing
The button that is hard to see says factory reset
m1shka said:
It's the official rom for the march ota.
The phone works, apparently it was encrypting everything... and now as I interrupted it, the encrypting failed and I lost all my data.....
Phone works but could have been better.
Before I reset the phone to factory, as i cannot use it yet, is there any way to get anything personal back? or is it gone gone and just factory reset?
What I see after boot, the phone resets every minute
https://drive.google.com/file/d/13sARZzlf3vJZK6Mx4hil6lsXRUl7-r-K/view?usp=sharing
The button that is hard to see says factory reset
Click to expand...
Click to collapse
Good job mate, so that SD card method worked with Linux? Be happy that your phone is alive.
EDIT: Maybe consider locking bootloader? Try it if youre on official stock.
EDIT 2: By flashing that ROM I guess you lost all data, but you can try to boot in TWRP without installing it and browse in file manager to see, if there is any data.
TrueMS said:
Good job mate, so that SD card method worked with Linux? Be happy that your phone is alive.
Click to expand...
Click to collapse
No... I was going to do that tomorrow but I decided to disable driver signature enforcement which worked. This should be written everywhere if it's this important..
Is there still a way to get my internal data back? Question as well, in recovery "mounting" the data partition will that let me get everything back "mounting" the drive to the pc? or do i not understand what mounting is.
m1shka said:
No... I was going to do that tomorrow but I decided to disable driver signature enforcement which worked. This should be written everywhere if it's this important..
Is there still a way to get my internal data back? Question as well, in recovery "mounting" the data partition will that let me get everything back "mounting" the drive to the pc? or do i not understand what mounting is.
Click to expand...
Click to collapse
As I said, you can try it, but when I flashed my Nougat stock ROM, i lost all the data. Or you can boot into TWRP and connect with USB to your computer to see the data in phone.
Good that your phone is working now, as for the data, i once forgot to remove encrypt before flash custom rom, but when enter TWRP it will ask for old password to decrypt. Just enter your old pass then connect to PC, or use TWRP file explorer to copy your data to sdcard
GVN.Gallus said:
Good that your phone is working now, as for the data, i once forgot to remove encrypt before flash custom rom, but when enter TWRP it will ask for old password to decrypt. Just enter your old pass then connect to PC, or use TWRP file explorer to copy your data to sdcard
Click to expand...
Click to collapse
None of the passwords I used worked.. I just factory reset it, thanks alot everybody. And now I will be more careful, don't flash anything weird. And backup!
I understood why I can't get the data back, if android fails at the encryption it jsut deletes everything!
My fone also in 9008 please can you guide me
I did the same what you have and it's on 9008 my flashing is successful but still my fone is not opening help me
m1shka said:
It's the official rom for the march ota.
The phone works, apparently it was encrypting everything... and now as I interrupted it, the encrypting failed and I lost all my data.....
Phone works but could have been better.
Before I reset the phone to factory, as i cannot use it yet, is there any way to get anything personal back? or is it gone gone and just factory reset?
What I see after boot, the phone resets every minute
https://drive.google.com/file/d/13sARZzlf3vJZK6Mx4hil6lsXRUl7-r-K/view?usp=sharing
The button that is hard to see says factory reset
Click to expand...
Click to collapse
How did you fixed i'm stuck in EDL?
SevenSlevin said:
If you are on "Qualcomm HS-USB QDLoader 9008" you will be able to flash stock fastboot firmware. Flash it using MiflashTool. Normally Miflashtool will recognized it as COMXX, where XX is the number of the port.
Click to expand...
Click to collapse
i am in Qualcomm HS-USB QDLoader 9008 but i can't flash, it doesn't matter if the phone is on fastboot mode or turned off (i can't even turn it on)
Hey guys,
Guess today it was my turn ****ing up.
I apparently have completely bricked my Axon 7 after trying to go from LOS 15.1 to stock oreo beta. The only thing I seem to be able to boot to is DFU mode and for some reason, if I press the Power button + Vol Down I will get stuck on the ZTE Logo and my PC will detect my phone through the ADB interface but every time I try doing something it says my device is unauthorized. Is there any way I can authorize the device whilst being completely bricked?
The only other thing I get is the unlocked bootloader warning screen. If I don't press anything the phone will be stuck there, if I select recovery the phone will simply shut down and anything else will result in a reboot. I have also tried a deep flash cable that that only results on the phone being stuck at the unlocked bootloader screen.
I cannot access the bootloader,
I cannot access EDL mode
I can access ADB, but device shows as unauthorized.
I can access DFU mode.
Any suggestions would be appreciated. I have looked at the Hard brick guide that involves taking the phone apart but that's not something I really want to do.
Thanks in advance.
Edit: My phone gets detected by MiFlash but every time I try flashing I get a cannot receive hello packet and object reference not set to an instance of an object.
ZTE axon 7 EDL tool detects it in ADB mode but says ERROR! NO ANSWER FROM PHONE!. Possibly since its not authorized with ADB.
Ouh....DFU? I think this thing is totally bricked.
I can access my phone in ADB. If only I could make it reboot to edl or something like that through ADB even though my device shows as unauthorized. That is the only problem why this thing is completely messed up.. ADB works but I can't do anything with it because my phone shows unauthorized. Does anyone know if there's a workround or a bypass for that?
Victor13f said:
I can access my phone in ADB. If only I could make it reboot to edl or something like that through ADB even though my device shows as unauthorized. That is the only problem why this thing is completely messed up.. ADB works but I can't do anything with it because my phone shows unauthorized. Does anyone know if there's a workround or a bypass for that?
Click to expand...
Click to collapse
Hi Victor !
Like we discussed before there is nothing much left as to use the DFU unbrick-disassemble guide or buy something like this to be sure you tried everything.
Good Luck mate !
raystef66 said:
Hi Victor !
Like we discussed before there is nothing much left as to use the DFU unbrick-disassemble guide or buy something like this to be sure you tried everything.
Good Luck mate !
Click to expand...
Click to collapse
Thank you for your help . It's a risk you take when flashing phones.
Can you get custom recovery in it some recovery allow you to get in to EDM from there you can flash stock rom with Mi flash tool.......try to push both volume buttons at the same time don't touch the power button this might get you in to EDM.
stinka318 said:
Can you get custom recovery in it some recovery allow you to get in to EDM from there you can flash stock rom with Mi flash tool.......try to push both volume buttons at the same time don't touch the power button this might get you in to EDM.
Click to expand...
Click to collapse
Hi. I cant get anywhere near recovery. When I press both buttons without the power button nothing happens. Thanks though!
Victor13f said:
Hi. I cant get anywhere near recovery. When I press both buttons without the power button nothing happens. Thanks though!
Click to expand...
Click to collapse
The screen will be blank untill you plug in USB cable to flash on mi flash tool then you refresh button on the computer screen....
stinka318 said:
The screen will be blank untill you plug in USB cable to flash on mi flash tool then you refresh button on the computer screen....
Click to expand...
Click to collapse
The moment I plug in any cable the screen turns on automatically. I've tried everything at the phone won't go into EDL. Thanks though!
Victor13f said:
The moment I plug in any cable the screen turns on automatically. I've tried everything at the phone won't go into EDL. Thanks though!
Click to expand...
Click to collapse
Nothing, you'll have to use my guide for that (the one that raystef linked). Otherwise try entering FTM mode (Power and Vol-) but it's surely not gonna work. If it does, you'll see a screen with a square that says "FTM", and you'll be able to do " adb reboot edl" and flash stuff from there.
Unbricking by disassembing the phone is the most reliable method; an EDL cable just might save you the hassle but it's not guaranteed to work; some phones won't accept it for some reason. In this case just follow the guide unless you want to try your luck with an EDL cable
Choose an username... said:
Nothing, you'll have to use my guide for that (the one that raystef linked). Otherwise try entering FTM mode (Power and Vol-) but it's surely not gonna work. If it does, you'll see a screen with a square that says "FTM", and you'll be able to do " adb reboot edl" and flash stuff from there.
Unbricking by disassembing the phone is the most reliable method; an EDL cable just might save you the hassle but it's not guaranteed to work; some phones won't accept it for some reason. In this case just follow the guide unless you want to try your luck with an EDL cable
Click to expand...
Click to collapse
Hello. Thank you for your advices, it is as I feared.
I have however already bought another Axon 7 which I'm using at the moment, and I have plans for mine since it was only bought new about 8 months ago and I believe I could get a replacement for a fee even if its bricked to fault of my own. So I will try that since I'm not in a rush.
This thread can be closed.
Cheers!
Victor13f said:
Hello. Thank you for your advices, it is as I feared.
I have however already bought another Axon 7 which I'm using at the moment, and I have plans for mine since it was only bought new about 8 months ago and I believe I could get a replacement for a fee even if its bricked to fault of my own. So I will try that since I'm not in a rush.
This thread can be closed.
Cheers!
Click to expand...
Click to collapse
In that case you can just pretend that the phone got in that state by itself, it's not too morally correct but some people here pulled it off...
twice now i have gotten an axon 7 into this state. while mine have been a2017u models, i dont know that they are different than yours in that regard.
What worked for me the first time was letting the phone completely die. Being unable to boot into anything, it was somewhat a task to actually make it die, so i kept powering it on (which merely made the red led indicator come on). i did this over and over again over the course of a day at work whenever i noticed it had powered off.
eventually, the phone had no response at all. then, i plugged it up to my laptop, and left it, convinced i had killed it. a dialogue popped up after a minute or two on the phone screen saying to charge the phone by plugging it up. i had no access to fastboot or EDL mode prior. once i got that 'plug in to charge' screen, i switched it to the wall charger, and left it to charge a bit (50-60%) from that state, then, i unplugged it again, and somehow, i managed to get edl mode to work by unplugging it and pressing all three buttons and holding them (typical edl boot).
once there, i reflashed via MiFlash an earlier build. i rolled back using MiFlash as far back as i could. in the process, i lost my imei and serial, which i have yet to successfully recover, but i did get out of DFU pergatory. the imei thing seems to be caused by going back to MM which i did on both of my IMEI-less a2017u boards, but im only guessing. my dd axon 7 is the only one of the three boards with imei and serial, so maybe MM is a bad idea. lol.
The first time i recovered from DFU, i did it inadvertently by letting the phone die and then flashing in EDL mode as well. (i left it for a few weeks as i had given up on it.) after it died completely, and i plugged ut up to the computer and had the same experience, I flashed the beta oreo build for a2017 using miflash. the screen had stopped responding. and i ended up doing a RMA. I now know the screen response thing was bc of a faulty EDL file of B15. (happened again to another of my axon, so i retraced my steps and realized it was when i flashed b15 that it died) . the fix if your screen ever stops responding, but isnt physically damaged? re-flash via EDL a different file. it may take a few tries, but eventually a build will work. for me, it was Marshmallow. I still do not know for certain, but that possibly is what killed my IMEI. but hey, it boots and the screen works.
I genuinely hope posting my idiocy in toying with axon 7s has helped someone out there.
Hello dear community,
I've been playing with my 6t for a long time, hundreds of custom roms, kernels, etc..
Lastly I went to official oxygen 10. I tried to install twrp via fastboot but every time I tried to push the files, I would get a error. I reinstalled drivers, tried different ports, different tools..
I got mad and blindly followed some article where someone suggested putting "persist" in the fastboot command, I tried it, I thought it is some kind of "force push" the file and that is how I probably corrupted persist partition. DUMB
Phone not booting of course and I went to restore it with Msmdownload tool.
It did not fixed it.
I tried different versions of msm, I tried going to Hydrogen, tried different USB ports, tried type C ports, different PCs...
No luck, phone is stuck at bootloop, with no TWRP and bootlocked.
I read somewhere that Msmdownload tool is not flashing persist partition and I assume that is the reason why my phone can't be restored.
Fastboot commands are not working anymore and EDL mode is probably the only possible way to communicate with the device.
I live in Montenegro and I can't send phone to oneplus to repair it.
I searched the threads and noticed that some users with similar problem eventually succeed to restore the phone by flashing it with Msm multiple times. I am still trying to do it but no luck.
I would really appreciate help from dev mastermind.
Thank you!
If your bootloader is locked again, i think it is not possible to use Msn tool. I think the only way is to send it for repair if you can't boot the phone.
But maybe i'm wrong and someone else know the sollution.
Deurklink73 said:
If your bootloader is locked again, i think it is not possible to use Msn tool. I think the only way is to send it for repair if you can't boot the phone.
Click to expand...
Click to collapse
Thank you for response, but I think that msmdowload tool is made mainly to be able to flash even locked bootloaders, although I am not 100% sure...
Papagaj said:
Thank you for response, but I think that msmdowload tool is made mainly to be able to flash even locked bootloaders, although I am not 100% sure...
Click to expand...
Click to collapse
You are correct. Msm tool will work on locked bootloader.
Man that sucks. Seems like you might be screwed. I screwed up a couple times getting to A10 but I was able to get msm tool to work for me. You are using it while your phone is powered off, correct?
Try different version of android with msm tool. Like try using the Android 10 msm tool then try the Android 9 msm tool
GeekMcLeod said:
You are using it while your phone is powered off, correct?
Click to expand...
Click to collapse
Hi GeekMcLeod, That's right, I boot it in bootloader mode, select "turn off" just to be sure that phone is shut down. And then I hold volume up and volume down together and plug the cable so it goes in EDL mode. Windows recognize it just as Qualcomm HS-USB QDLoader 9008, and that is all right I think.
Then I start MSMdownload tool and it flashes everything in around 200 seconds. I leave phone pluged in while it try to boots, but it never boot up. I left it for 45 minutes but still nothing...
jamescable said:
Try different version of android with msm tool. Like try using the Android 10 msm tool then try the Android 9 msm tool
Click to expand...
Click to collapse
I tried several versions. I was hoping to find Android 10 tool for oneplus 6t but it is still not available.
Papagaj said:
Hi GeekMcLeod, That's right, I boot it in bootloader mode, select "turn off" just to be sure that phone is shut down. And then I hold volume up and volume down together and plug the cable so it goes in EDL mode. Windows recognize it just as Qualcomm HS-USB QDLoader 9008, and that is all right I think.
Then I start MSMdownload tool and it flashes everything in around 200 seconds. I leave phone pluged in while it try to boots, but it never boot up. I left it for 45 minutes but still nothing...
Click to expand...
Click to collapse
Sounds like a driver problem to me. Try gathering a few (by Google, OnePlus, perhaps even Samsung) and keep trying different ones. I had to do this on my OnePlus One years ago. Then suddenly I found one that worked and I could revive it back from the dead. Not saying that it would work for you but it might. In my case it was a Qualcomm tool. If you still end up with nothing but dead ends today, I'd initiate a chat with OnePlus on this page (select your country at the bottom of the page first).
Wrapped with delicious Fajita [emoji896]
The only solution is to use smt mode inside msmdownloadtool, which will restore persist partition, but with some disadvantages.
Be aware that you WILL LOSE YOUR IMEIs and WIDEVINE L1, use it at your own risk.
If you decide to do it (remember you WILL LOSE YOUR IMEIs and WIDEVINE L1!) follow this:
1.- Run MSMDownloadTool.
2.- Click on Verify and wait till it says "MD5 Check OK!".
3.- Then click on SMT Mode.
4.- Then click on Start like you would normally do with upgrade mode.
5.- The you need to enter as password "te123" and select your phone's capacity.
6.- If it says something like "Port disabled by user", go to the top left corner and click on "SMT", "COM Setup" and check everything, then click on the left button, and retry steps 4-5.
7.- When the process finishes the phone won't reboot, so you'll need to hold VolumeUP+Power until it powers on, then wait around 5 minutes and your phone will be back to life!!
8.- If you have an IMEI backup, just follow this guide (https://forum.xda-developers.com/oneplus-6t/how-to/guide-oneplus-6t-unlock-bootloader-t3851789) (I don't know if this is the correct way to post links)
I hope you get your phone fixed.
Papagaj said:
Hi GeekMcLeod, That's right, I boot it in bootloader mode, select "turn off" just to be sure that phone is shut down. And then I hold volume up and volume down together and plug the cable so it goes in EDL mode. Windows recognize it just as Qualcomm HS-USB QDLoader 9008, and that is all right I think.
Then I start MSMdownload tool and it flashes everything in around 200 seconds. I leave phone pluged in while it try to boots, but it never boot up. I left it for 45 minutes but still nothing...
Click to expand...
Click to collapse
Don't go to edl mode. Just have your phone powered off and use msm tool. I used it a couple times while getting to A10 and I only ever had to power my phone off.
amt911 said:
The only solution is to use smt mode inside msmdownloadtool, which will restore persist partition, but with some disadvantages.
Be aware that you WILL LOSE YOUR IMEIs and WIDEVINE L1, use it at your own risk.
If you decide to do it (remember you WILL LOSE YOUR IMEIs and WIDEVINE L1!) follow this:
1.- Run MSMDownloadTool.
2.- Click on Verify and wait till it says "MD5 Check OK!".
3.- Then click on SMT Mode.
4.- Then click on Start like you would normally do with upgrade mode.
5.- The you need to enter as password "te123" and select your phone's capacity.
6.- If it says something like "Port disabled by user", go to the top left corner and click on "SMT", "COM Setup" and check everything, then click on the left button, and retry steps 4-5.
7.- When the process finishes the phone won't reboot, so you'll need to hold VolumeUP+Power until it powers on, then wait around 5 minutes and your phone will be back to life!!
8.- If you have an IMEI backup, just follow this guide (https://forum.xda-developers.com/oneplus-6t/how-to/guide-oneplus-6t-unlock-bootloader-t3851789) (I don't know if this is the correct way to post links)
I hope you get your phone fixed.
Click to expand...
Click to collapse
@Papagaj do this....thats the only fix....I purposely wipe persist for to test something and I did that to recover from the boot loop.. persist store sensor information that vital to getting phone to boot....that's why it not booting..kernel is look for the sensor info but can't find it
Timmmmaaahh said:
Sounds like a driver problem to me. Try gathering a few (by Google, OnePlus, perhaps even Samsung) and keep trying different ones. I had to do this on my OnePlus One years ago. Then suddenly I found one that worked and I could revive it back from the dead.]
Click to expand...
Click to collapse
Timmmmaaahh I am so glad to see you on my thread! I learned fundamentals of flashing on your guides back in Bacon days, and never bricked it even once! But this A/B partitions really gave me headaches....
It is highly likely that drivers are causing problem, I tried to flash it with msm tool on fresh windows where I let it to automatically download required drivers and the msm progress appear to be same as when I used drivers which are recommended by msmtool developer. I will try several more and will be back with results within few hours.
amt911 said:
The only solution is to use smt mode inside msmdownloadtool, which will restore persist partition, but with some disadvantages.
Be aware that you WILL LOSE YOUR IMEIs and WIDEVINE L1, use it at your own risk.
8.- If you have an IMEI backup, just follow this guide
Click to expand...
Click to collapse
Is there a way to backup IMEI and WIDEVINE L1 at this moment? I think it is highly unlikely because functionality is limited to EDL only....
Or is there a way I can restore it later if I manage to fix a device with smt mode?
GeekMcLeod said:
Don't go to edl mode. Just have your phone powered off and use msm tool. I used it a couple times while getting to A10 and I only ever had to power my phone off.
Click to expand...
Click to collapse
How do you mean? I can't get phone connected with msm tool if it is not in EDL mode.. It is not recognized when in stock recovery, bootloader or trying to boot up OS, that is only three states this phone can be at the moment.
Papagaj said:
Timmmmaaahh I am so glad to see you on my thread! I learned fundamentals of flashing on your guides back in Bacon days, and never bricked it even once! But this A/B partitions really gave me headaches....
It is highly likely that drivers are causing problem, I tried to flash it with msm tool on fresh windows where I let it to automatically download required drivers and the msm progress appear to be same as when I used drivers which are recommended by msmtool developer. I will try several more and will be back with results within few hours.
Is there a way to backup IMEI and WIDEVINE L1 at this moment? I think it is highly unlikely because functionality is limited to EDL only....
Or is there a way I can restore it later if I manage to fix a device with smt mode?
How do you mean? I can't get phone connected with msm tool if it is not in EDL mode.. It is not recognized when in stock recovery, bootloader or trying to boot up OS, that is only three states this phone can be at the moment.
Click to expand...
Click to collapse
Nope....just rewrite you IMEI with a Qualcomm tool..quite a few available
Papagaj said:
How do you mean? I can't get phone connected with msm tool if it is not in EDL mode.. It is not recognized when in stock recovery, bootloader or trying to boot up OS, that is only three states this phone can be at the moment.
Click to expand...
Click to collapse
Oh. The few times I used it I just powered off my phone and connected it to my computer. Started msm tool and it did its thing.
Papagaj said:
this A/B partitions really gave me headaches
Click to expand...
Click to collapse
You and me both! ? lol...
I recently got stuck in a weird bootloop thing with a, what i think was, corrupted boot.img. Try finding a stock android boot.img, boot to fastboot, and run the command fastboot flash boot <boot.img> on both partition A and B. If you can't find a stock boot.img, i managed to find one and can link to a download.
All right, here is the situation.
I finally managed to boot up the phone. amt911 gave working instructions on post #10. Thank you bro, you are awesome, and Thank you Tech_Savvy for confirming the method, you are badass who deletes partitions just for fun!
All right I got the phone booted up but as amt911 mentioned, I lost my IMEI numbers, without IMEI numbers you can't dial numbers, receive calls or use mobile data.
BACKUP IMEI NUMBERS FOLKS, you never know when the partitions will screw you over!
I was dumb one without backup and I had to contact Oneplus support for help. I was suprised how quickly I got into communications with one of the assistants.. in less than 10 seconds.
They ask you to do full reset via stock recovery and some other basic troubleshoots, after nothing, obviously, fix the missing IMEI they will arrange remote session to get your phone fixed.
You have to persist on remote session as some of assistants told me that I have to send the phone to repair.
Before they arrange session for you, you need to show them "proof of the purchase" ALSO KEEP THAT FOLKS I lost mine long time ago but luckily I found photo of invoice I took when I bought phone, phew*
I didnt have it at first when I contacted them and they say there is nothing they can do without a proof! DON'T STEAL PHONES FOLKS and then ask for support...
They will contact me for session within 48 hours and I will share the experience here.
Thank you again people!
JTVivian said:
I recently got stuck in a weird bootloop thing with a, what i think was, corrupted boot.img. Try finding a stock android boot.img, boot to fastboot, and run the command fastboot flash boot <boot.img> on both partition A and B. If you can't find a stock boot.img, i managed to find one and can link to a download.
Click to expand...
Click to collapse
Thank you JTVivian for helpful suggestion, but that method would not work. When your bootloader is locked, fastboot commands are useless, you can't flash anything.
Papagaj said:
Thank you JTVivian for helpful suggestion, but that method would not work. When your bootloader is locked, fastboot commands are useless, you can't flash anything.
Click to expand...
Click to collapse
Ah you're right, i wasn't sure if that was the case but i thought i'd throw out the suggestion anyways.