After searching xda for a proper guide on how to get the G Pad 10.1 back to working order, I was unsuccessful so after a few hiccups I was able to bring the tablet back to life, so here it goes. This has been tested on a LG Pad 10.1 (e9wifi), photos archived below for reference. I found the firmwares for the V700 online and i will post the link below so you can them to.
After flashing the G Pad 10.1 you WILL LOSE ALL OF YOUR FILES AND I AM NOT RESPONSIBLE FOR ANYTHING YOU DO TO YOUR BELOVED TAB.
0. So first of all, in order to avoid detection errors in Windows install the appropriate drivers linked here.
1. After installing the drivers, download your firmware here and LG Flash Tool 2014 here.
2. In LG Flash Tool 2014 make sure that the Select Type is 3GQCT and the PhoneMode is EMERGENCY. Also select the .kdz file (firmware) by clicking in the folder next to Select KDZ file that you previously downloaded. Then Press Normal Flash.
3. Next click START and when the Select Country & Language window appears just select OK.
4. After that turn your tablet off and press the Volume UP key and connect the tablet to the PC.
5. Just the the program do its thing and after 5 min or so the tablet will be booting and working just as normal. :good:
HELP!!
hey there I've tried this on my G pad V700 and it gets to 49% and stops! Not sure why im doing all the steps correctly!
Related
Hello!
I have a good news for all Memo Pad Smarts owners. I found a way to flash this tablet when we are on locked bootloader and obtained bootloop. I tried to update it with method for TF300T (update file named to EP201_768_SDUPDATE) but not working, then i go to /cache/recovery and find file last-log (my tablet wasn't bricked) and i find line like that: "Can't find update file" EP201_1024_SDUPDATE". So I renamed my update file to EP201_1024_SDUPDATE and it work! Now I'm going to write a whole instruction step by step.
Instruction:
1. Download file from asus.com: WW_epaduser_10_4_5_27_12_UpdateLauncher.zip
Attention! firstly check your SKU. This file is for WW SKU!
2. Extract first zip, and rename the zip which you extracted from the first to EP201_1024_SDUPDATE
3. Format SD cart with FAT32 and copy file on this - it shouldn't be in any folder!
4. Put SD in to your tablet
5. Turn on your tablet by holding POWER+VOLUME DOWN until you see ASUS logo.
6. Choose RCK option by pressing VOLUME DOWN - it should by choose by default, then press VOLUME UP to enter RCK
7. Now wait several minutes - be patient!
If you have any problems, write there!
It is the same method for TF300T/TF700T . I think XDA should join all this devices on one forum since they have so many things in common...
Anyway, take my thanks
Yes, the difference is only name of file. Anyway this devices are very similar
Sent from my LT26i using xda premium
Hello I tried but I can not update, my TF300T you help me? I would like to reinstall this version WW_V10.6.1.15.3 thanks , my pc is broken, so it can not use it or anything else adb
tanks
Send to Asus tf300t JB 4.2.1 rooted And Galaxy S2 Nfc JB 4.1.2
This tutorial is for me301t, but if you have tf300t just change file name to EP201_768_SDUPDATE and it should work. Remember download file from section for tf300t on asus site
Sent from my ME301T using XDA Premium HD app
Perfect .... you are great!:thumbup:
Send to Asus tf300t JB 4.2.1 rooted And Galaxy S2 Nfc JB 4.1.2
Please help
I need help I rooted my MEMO 10 pad with no problem then i tried to load beats audio. Big Mistake. now it is just stuck on the asus load page with the wait circle going round. I tried the method suggested here hoping it would wok but alas it has not. please help I just got this tablet 2 days ago
whaaaa?
1. Download file from asus.com: WW_epaduser_10_4_5_27_12_UpdateLauncher.zip
I've been looking around on the asus site for that file and I can't find it! could you give me a link?
having huge problems with my asus MeMo pad (smart 10") I have a whole bunch of corrupted apps that are rendering my tablet essentially a brick. my launcher, keyboard, and UI are all fried. I cannot even boot into recovery. is there anything I can do to fix this?
Please help
I can't go to recovery mode nor fastboot how to fix it
This works.
This worked for me. Just signed up here to say that.
I have ME301T
Sounds crazy but I did as instructed in Michal's OP and it worked.
Unzipped the zipfile downloaded from Asus.com (can't post link due to noob status. Search on asus for memo pad smart 10 then select drivers and tools, then OS and then firmware)
renamed the zip that is extracted from that zip, as described in OP.
put it on my fat32 SD and it worked.
My tablet randomly started bootlooping, I didn't add any new apps or make other changes before, it just started looping randomly.
I may have let the battery drain completely though. Had to unplug the battery (youtube describes this) before trying reloadin order to get it to start charging again. Then did the procedure in this thread and I'm all good now.
Thank you!
boot loop
Cheers M8 worked like a charm after i renamed it indeed to 1024.
Much appreciated !!!
ME 301T memo pad 10
Michal1994 said:
Hello!
I have a good news for all Memo Pad Smarts owners. I found a way to flash this tablet when we are on locked bootloader and obtained bootloop. I tried to update it with method for TF300T (update file named to EP201_768_SDUPDATE) but not working, then i go to /cache/recovery and find file last-log (my tablet wasn't bricked) and i find line like that: "Can't find update file" EP201_1024_SDUPDATE". So I renamed my update file to EP201_1024_SDUPDATE and it work! Now I'm going to write a whole instruction step by step.
Instruction:
1. Download file from asus.com: WW_epaduser_10_4_5_27_12_UpdateLauncher.zip
Attention! firstly check your SKU. This file is for WW SKU!
2. Extract first zip, and rename the zip which you extracted from the first to EP201_1024_SDUPDATE
3. Format SD cart with FAT32 and copy file on this - it shouldn't be in any folder!
4. Put SD in to your tablet
5. Turn on your tablet by holding POWER+VOLUME DOWN until you see ASUS logo.
6. Choose RCK option by pressing VOLUME DOWN - it should by choose by default, then press VOLUME UP to enter RCK
7. Now wait several minutes - be patient!
If you have any problems, write there!
Click to expand...
Click to collapse
my ME 301T is not booting i followed the instruction above but from RCK it donot detect SD, i shows a robot with top door open and red triangle, i do not know what to do?
same problem
ansm32000 said:
my ME 301T is not booting i followed the instruction above but from RCK it donot detect SD, i shows a robot with top door open and red triangle, i do not know what to do?
Click to expand...
Click to collapse
I have the same problem with the TF300T
the file should be named
Code:
EP201_1024_SDUPDATE.zip
Hi all,
(previous situation:
- My tablet started boot looping, maybe because of letting the battery drain.
- Hard/ soft reset did not work, wipe data did not work, ended up in boot loops.)
Tried this method today, and after pressing RCK the tablet restarted: Now changing between the android robot (without the red triangle) and the Asus display.
Any suggestions?
Thank you!!!! :good:
Finally, the system update was installed on my unbootable ASUS MeMO Pad K001 / ASUS MeMO Pad Smart 10 / ME301T.
Clarification:
Michal1994 said:
2. Extract first zip, and rename the zip which you extracted from the first to EP201_1024_SDUPDATE.zip
Click to expand...
Click to collapse
The .zip file extension is needed.
I used a 8GB MicroSD card that was already FAT32 formatted and had other files on it.
This applyes to ASUS MeMO Pad FHD 10 (ME302KL)
Format SD card with FAT 32 and copy the zip file inside this archive http s://dlcdnets.asus .com/pub/ASUS/EeePAD/ME302KL/ME302KL-JP_epad-user-10_10_3_41-UpdateLauncher.zip
So this file JP_epad-user-10.10.3.41.zip will be in your root on sdcard
Enter recovery mode by double making the recovery entering procedure, holding power + up, sounds weir but it worked
select adb sideload and do as here: http s://www .youtube.com/watch?v=SHu-CMubrhA - i used command prompt in admin mode powershell didn`t worked for me
Hi all,
i have a problem, got a new Lg L7 P710, and i wanted to jailbreak/root etc. but i think i failed with it.
also i tried with KDZ updater, and installing LG modem and Lg Androidnet usb serial port (com6)/ and installed all those drivers needed. My SD card is still in the phone, but i can't see it in ''my Computer'' when my LG is plugged into mine laptop.. also the rooting part its failing.. btw my yellow screen for emergency is not normal, its kinda with stripes, and i can't see the ''emergency' 'word on the phone when it is yellow, sometimes it goes blue screen with stripes...
i don't think its a hardware problem, but i accidently deleted everything also in SD card, and in the phone self, its just like a Stock peg...and also i lost my warranty in 3 weeks -_-'', i can't do anything, only plugg it in mine laptop, and i hear a noise sometimes, dat it is plugged in, but only in ''Device manager'' I also read some other forums, with bricked or unbricked, or ADB ( also tried with this and CMD) but didnot recognise mine phone... as you can see, my phone is connected to mine laptop ( see pictures)
any solutions/help please? :crying:
try this
try to download your software version put it on a sdcard then try to enter recovery and then try to install from sd card.
u got here the original rom from http://forum.xda-developers.com/showthread.php?t=2167344 and some help
How to Unbrick / Return LG Optimus L7 II Back to Stock
Warning: I won’t be responsible for any damage to your device, this has been tested and working on my device, good luck!
Requirements::
• A Windows Based PC
• An LG Optimus L7
• Official stock firmware
• KDZ_FW_UPD_EN.zip
• LG Optimus L7 USB Driver
How to Unbrick / Return LG Optimus L7 Back to Stock Steps:
1. Download and install USB Drivers on your PC
2. Download the official stock firmware
3. Download KDZ_FW_UPDATE.zip and extract it,then open the folder where you extracted it and Start KDZ_FW_UPDATE_EN with Administrator Rights (Right Click on file and select Run As Administrator)
4. Once the program started, in Type select 3GQCT and in Phone Mode select EMERGENCY, then in KDZ File select the downloaded firmware and press open.
5. Make Sure your Phone is connected to the computer in EMERGENCY MODE( Remove the battery from the phone,then while pressing Vol- Connect the usb to the computer,a yellow screen must come up showing EMERGENCY)
6. Once you’ve done this,press Launch Software Update and let it work,the procedure takes about 5-10 Minutes,so don’t worry.
7. At the end of the procedure the phone will reboot and an LG Animated Logo will come up,and after some minutes KDZ_FW_UPDATE Will say you that there has been an error, don’t panic.
8. Congratulations.
Caution: Don’t unplug the USB cable until the setup has finished.
http://allphonefirmwares.blogspot.mx/2013/06/how-to-unbrick-return-lg-optimus-l7.html
Hi, I have same picture on my L7 display and I dont know what to do. I tried to reflash over KDZ, it seems that phone is installing SW before first reboot. After reboot KDZ updater stops working Any suggestion? Somewhere I found, that only way is to use JTAG.
...
I have the same problem,one of my frends is trying to put kit kat on l7 p710,but he is so stupid... he download and put firmware for l9... now i trying to repare it i can't find the phone in device manager... anyone find a solution? please HELP!!!
Brick other brand new LG G2 D802 32GB taken out from the box. Oryginal version of KDZ installed by factory: V20B. Upgrade to V20 G (45 Baltics). Phone connect to PC with download mode, CDMA, DIAG, CSE Flash. Phone Unrooted. After finish download the firmware into phone following symptoms: when touch the screen for example "english UK" the phone doing something different/elese-the phone select together other 2 buttons on the bottom (arrow button and 3 lines), phone is completely crazy, go to next step (from point of select the language) is impossible. Recovery Mode not available, Download Mode available.
I tried repair method with TOT & DLL file using LGFlashTool 1.8.1.1023 unfortunately this not help.
I think the reason is that phone should be rooted before upgrade (before use the FlashTool).
Anyone have any solutions, suggestions?
My phone is completely dead.
I can´t boot into bootloader/recovery/download modes neither through adb or hardware keys (gets stuck into LG logo).
I have tried doing it with or without battery/microSD/SIM.
It can boot into Cyanogenmod for like 5 seconds just to get to a Demigod Crash Handler (rinse and repeat).
I have a logcat, it is here: http://pastebin.com/wmmTTyqL
This is the kernel-panic (extracted through adb pull): http://pastebin.com/KqeCM9qz
All of this started by flashing through TWRP (@aidasaidas75´s version) Lukosius kernel r16.1
I´m short on money and I can´t buy a new phone.
Is there any hope of revival?
Thanks in advance.
Use the download mode to restore the apropiate kdz file to revive
Step1. Search for all software you will need such as:
A. LG Firmware: firmware
Only select your mobile model phone and country and download the carrier you want to use.
B. Download the LG drivers from here: drivers
C. Download the KDZ installer from here: installer
Step 2: Install the drivers (I did it in a Windows 7 32 bits computer)
Step 3. Unzip and install the KDZ installer (Step 1. Section C: KDZ_FW_UPD.exe)
Step 4. Set your phone in emergency mode:
Reboot your phone: (remove your battery and set it again) while press + and - volume buttons, then connect your USB cable.
Step 5. Select your KDZ(Step 1. Section A) in the installer with the following options:
TYPE: 3GQCT
PHONEMODE: DIAG
Follow the instructions and wait until the software reboot your phone.
Pls help.
Recently i hard bricked my lg optimus l5 e612 because of swapper2 app.Now phone not boot up, no sound ,no led lights,not able to boot in any recovery or mode, i read all the related post and tried all the things. Tried all key combinations with and without battery but not getting the way.also tried kdz but it says PHONE NOT Found.is it still any way to get back life of my Phone.
Thanks in advance.
Any there can solve the problem how to fix lg.optimus l5 e612 won't turn on and not charging no recovery,downloading mode?
im not sure if that will help
http://www.ninjaromeo.com/unbrick-lg-optimus-l5-using-kdz/
here the search i used
https://www.google.com.eg/?gws_rd=ssl#newwindow=1&safe=off&q=unbrick+lg+e612f
i hope that help you
Thanks very much for your help.
But main problem is phone not detected by computer.
And not able to enter in any mode or recovery.
If there is any solution for enter in to download or in emergency mode then It will be open the door to get back life of my optimus l5.
sorry to hear that if phone not detected by computer with all ways and all possible ways in the search results its means that you need to make RIFF connection
try to do search like that
https://www.google.com.eg/?gws_rd=ssl#newwindow=1&safe=off&q=LGE612F+RIFF+
and thats the only last way to revive the phone
sorry but i have no more ideas to help
Hello.
If your phone is stuck in a "boot-loop" or is "soft bricked" (security authentication error #9) or otherwise a 'paper-weight' in your eyes already: Give this a try! (Windows platforms only)
LG UP software will flash the ROM with a *.KDZ file (LG / T-Mobile's custom image format).
You can find the LG UP software on this site: https://www.mylgphones.com/download-lg-up-software
You will want to download the LG UP Lab v1.10 version of the software.
On the right panel of the screen: Find "LG USB Drivers" and find the appropriate one for yourself. Then install it on your PC.
Initiating "download mode"
Power down your device completely. Press and hold the "VOLUME UP" key; While holding the VOLUME UP key: Insert the USB cable (it should already be attached to the PC).
The phone will automatically power on and the "DOWNLOAD MODE" image should appear instantly. After this appears: Release the VOLUME UP key.
You should be able to place the phone down and run the LG UP software. You need to select "UPGRADE" (not "refurbished"), then locate the KDZ file (bottom right corner of the program is a vertical "3-dot" image; Used to navigate to your *.kdz file).
Merely hit "START" and wait about ~300s (~5m). The phone will reboot itself. You can exit the program at this point by pressing "Exit."
Finding your stock firmware ROM image:
You can locate your firmware to flash on this site: https://mega.nz/#F!sdwRDLbZ!yPOiRPv5QJS_9I4hzL4ptQ!oVJyjTYB
You can flash as many as times as you'd like. It won't cause you to be unable to boot up to "DOWNLOAD MODE" ever. So do not worry about getting the wrong KDZ image file downloaded the first time. They are ~1GB in size each.
That's it! I hope this helps.
Suggestions include:
Install a TWRP (Team Win Recovery Project)
Install SuperSU (root your phone)
Install ADB (on your PC; A useful utility for installing TWRP / rooting your phone / modding your phone)
When I run LG UP, I get a dialog that says Model List. Under Model it says "unknown" and under COM Ports it says " COM3,K33010l ". When I hit select it says, "You have to select a known model, please."
albamuth said:
When I run LG UP, I get a dialog that says Model List. Under Model it says "unknown" and under COM Ports it says " COM3,K33010l ". When I hit select it says, "You have to select a known model, please."
Click to expand...
Click to collapse
I ran into a similar issue with a different model.
Try using a different COM port to communicate on.
The common ones I remember using were: 3, 4, 20, 40 and 41.
To change the device's COM port: You should be able to locate it in Windows under the "Device Manager."
The fastest way to get there is to use hotkeys.
Accessing Windows device manager:
Windows key + R
devmgmt.msc (press enter)
You should see your phone listed in the menu tree. Right click on it, then select "Properties."
You should be able to change the COM port it communicates on in one of the sub-menus.
Unfortunately: I do not have a phone and USB handy with me at the moment to look it up.
So i have a k7 europe version. Model info says its x210 so none of the files here are for a x210 variant. Can i use the other files to try and fix the boot loop? Or will i brick my phone even worse? Im stuck in bootloop but i can enter fastboot. Can someone give me some direction?
kondore said:
So i have a k7 europe version. Model info says its x210 so none of the files here are for a x210 variant. Can i use the other files to try and fix the boot loop? Or will i brick my phone even worse? Im stuck in bootloop but i can enter fastboot. Can someone give me some direction?
Click to expand...
Click to collapse
nobody ?
I no longer posses this phone and cannot offer advice.