Related
After i hang up on a call (when the phone is in sleep mode and the screen is locked) the screen unlocks. this is quite contrary to what is mentioned in the phone manual chapter 1 page 45. this becomes an issue since i use a bluetooth headset and the phone remains in its sleeve/case and after every call, a whole bunch of applications will launch since the case is in contact with the screen. have i overlooked some settings or are there other owners who have faced this issue?
ideas and suggestions welcomed
did you check it out if any of the hardware buttons being pressed against the case hence wakening up the phone.?
i had it to only closed al my apps in taskm and it stoped flickering
My HD2 is also behaving in the same way even in controlled test conditions - the phone unlocks when a call comes in (I'm presented with slide to accept or reject call) The phone unlocks during the call, but fails to lock again on disconnect (either by pressing "end call" or hang up via bluetooth).
Can anyone verify this? Is it interacting with something I installed?
I believe I found a (complicated) workaround.
What I want: leave HD2 inside pocket, answer calls with bluetooth headset, hang up and phone will go back to lock.
Problem: After I hang up using bluetooth or press the big red "End Call" button or the other party hangs up, the phone stays unlocked! It stays powered on and all kinds of buttons gets clicked.
Practically all lock sw uses their own lock screen (which I don't want to install). CSDevCtrl does not trigger by phone. TouchLockPro uses its own transparent lock screen but can respond to phone events. Using the !SUSPEND for TAPI\Ended under settings does not seem to work when the screen dims about 50 secs into the call.
Solution: Use TouchLockPro together with LockAndOff. Get TAPI\Ended to run LockAndOff will turn phone off, whether by bluetooth, big red "End Call" button, or the other party hangs up.
BTW: I think there is some confusion on whether the phone locks when you
1. press the big red "End Call" button, or
2. the hard "End call" button
in the forums.
I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.
linivan said:
I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.
Click to expand...
Click to collapse
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)
johncmolyneux said:
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)
Click to expand...
Click to collapse
My proximity sensor does not work, when I am getting a call my screen turn off and when I am taking the phone out from my face it turn on only when I am out side at the sun!! the screen stay off when I am inside room. I tested it with flsh light and it is working also.
I have a T-Mobile US version of the HD2. I am having the same problem when using the bluetooth system in my car. After answering or making a call the phone stay unlocked. And then starts making random calls while I am driving!!!!
There has got to be an easy fix for this!!!
Buy pocketshield, problem solved.
i have this unlock problem with 1.48 rom and i solve it by pressing start button and lock. after that everything works fine unless i change theme in settings. then just repeat first step.
Solved
Same trouble with me until I use the following software. I tried it and it's almost perfect. unzip it and just copy to your HD2, run CallerLoc.exe and click Yes, you'll find:when you hang up, or he/she hang up a call, or a call is established, the screen will turn off.
Why say 'almost perfect', the software is in chinese, but the filename is in english. and it's a call location software but with the function we need.
To stop or before you delete the software, run Callerloc.exe and click Yes again.
Hope this will help you. Sorry I don't find a English version of this software. I esure and I'm using this software perfectlly with my Leo.
theciscokid said:
Buy pocketshield, problem solved.
Click to expand...
Click to collapse
Same for me
Greetings.
I understand this is quite an old thread I'm digging up but I need a little help as well and I didn't want to start a new topic just for that.
I've this silly problem, appeared right out of the blue:
You all know the standard manila behavior, when the phone is idle, the screen first dims and after some more time, depending on your preferences, the screen locks. It also locks if you press the power off button. This all was happening to me till this morning.
I added an event in the calendar (the only change I made today) and after that, my phone dims and then goes in sleep mode after the designated period of time, but DOESN'T lock!!! It doesn't even lock when I press the power off button. I can still lock it by pressing Start and then lock or by press and hold the power button and choose the lock phone option. So one would say that it's still operational, so why bother about it, but I kinda liked the standard function and I have to freaking idea why it changed!!!
I'd be most appreciative if you could offer some help with that.
Oh, I forgot to mention. Soft reset didn't solve the problem. Erasing the calendar event didn't either.
My phone runs the factory ROM (1.66.482.1 ELL), I haven't changed anything other than user settings (yeah, I'm a noob... )
Thanks in advance!
Nasos
Pocketshield could be the end of your problems. You can try it for 10 days and see how it goes...
But why do I need to buy third party software in order to revert my phone to it's original operation?
No, this is not the answer I am looking for. I was wondering if you know of any kind of settings that might have changed by accident and caused this undesired behavior.
Thanks.
The best to return to normal operation would be a hard reset. Or you can spend a while trying.
You can try
HKLM\Software\Microsoft\Shell\Lockscreen\Enable=1
HKLM\Software\Microsoft\Shell\Lockscreen\Active=1
Thank you very much. I opted for the hard reset option... I hope it stays ok this time!
My HD2 also had some strange unlocking and unwanted calling.
I noticed it appeared when using the android style lockscreen.
When I changed back to the original one, problem solved
i had this too. the andriod lockscreen seems to be a bit buggy last time i used it, i accidentially called 7 random numbers
I am using the European Tab, but that probably makes no difference.
For security, I lock the phone automatically after 3 minutes of inaction. This works fine for all apps except phone. Strangely, after dialling (or after picking up a call) the phone first turns off the screen, and briefly thereafter locks the device, within 10 seconds. I can continue the call, but as the screen is off, I can not hang up, unless I first switch it on and enter the password.
I have not found a parameter to influence this behavior. But I know it is not related to the proximity sensor, as the effect happens the same way even when not moving the device from the desk.
Is this a confirmed behavior or does anyone know a cure? It's ok if the screen goes dark, and even if you must turn on via power button, but the password?!
Thanks for any help,
Rolf
rgbigel said:
I am using the European Tab, but that probably makes no difference.
For security, I lock the phone automatically after 3 minutes of inaction. This works fine for all apps except phone. Strangely, after dialling (or after picking up a call) the phone first turns off the screen, and briefly thereafter locks the device, within 10 seconds. I can continue the call, but as the screen is off, I can not hang up, unless I first switch it on and enter the password.
I have not found a parameter to influence this behavior. But I know it is not related to the proximity sensor, as the effect happens the same way even when not moving the device from the desk.
Is this a confirmed behavior or does anyone know a cure? It's ok if the screen goes dark, and even if you must turn on via power button, but the password?!
Thanks for any help,
Rolf
Click to expand...
Click to collapse
It happens to me lately after I flashed a new Rom but I highly doubt that has anything to do with it...it feels like a proximity sensor issue, and a autolock issue as well . I am Clueless sorry
I've had a problem with my E900 since I got it with regards to the screen. I was hoping Mango might fix it but it doesn't seem to have.
Sometimes if I press the power button the screen backlight comes on (i.e. screen goes from off state to powered) but there is nothing on the screen. No amount of button pressing will cause the screen to show anything.
If this happens I have to turn the device off again (backlight then goes off) and try again. Sometimes it can take 2-3 times before it turns on successfully with the lock screen.
I also have this if an incoming call attempts to wake the phone and also alarms too.
Does anyone else have this issue?
I confirm this one popping sometimes. Not that often that it becomes annoying, but nevertheless.
Did you find a solution to this problem? I am experiencing it too and it is very annoying!
I've recently inherited one as well (E900 that is).
The one I have has been dropped, the backlight powers, but no drawing on the screen.
I've disassembled and re plugged everything (bugger stripping down!) but still no luck. I've done a VolUp+Down+Cam+power hard reset, and when I plug into PC Zune says setup needs completing (so it has reformatted) but still no luck.
I cant see anything fried, and no damaged ribbons as far as I can see, any ideas?
I sold the phone a while ago, and never solved the problem. I think it's a firmware issue.
PaulMdx said:
I've had a problem with my E900 since I got it with regards to the screen. I was hoping Mango might fix it but it doesn't seem to have.
Sometimes if I press the power button the screen backlight comes on (i.e. screen goes from off state to powered) but there is nothing on the screen. No amount of button pressing will cause the screen to show anything.
If this happens I have to turn the device off again (backlight then goes off) and try again. Sometimes it can take 2-3 times before it turns on successfully with the lock screen.
I also have this if an incoming call attempts to wake the phone and also alarms too.
Does anyone else have this issue?
Click to expand...
Click to collapse
hi.
What do you mean "somethimes if I press power button"?
Is it pressed with purpose to lock the phone, press it to turn off phone (background slider shows to power off - on Mango and beyond version) or press it accidentally?
Cheers.
So, I did a phone reset. Unfortunately the issue is still present!
Sometimes when I press the power button to unlock the phone the screen is lit, but stays blank i.e. no lockscreen wallpaper, no nothing. The same happens sometimes when I get a phone call - the phone rings and vibrates, the screen is lit but stays blank.
When this happens I have to press the power button to put the phone into sleep mode and press it again to wake it up.
What I found is, when the issue occurs the screen is actually responsive. For example I can slid up and unlock the phone then I hear the unlock "pop" sound. It's just that nothing is drawn on it!
I was wondering if anyone else experienced the same behavior and found a resolution. Also I am not sure if this is a software or a hardware problem. If I could confirm it was a hardware problem I would call LG and have the phone repaired or replaced.
i have exactly the same issue as you, it gets really annoying.
i heard from someone online that the only way to resolve it is to replace the motherboard
billybrown said:
i have exactly the same issue as you, it gets really annoying.
i heard from someone online that the only way to resolve it is to replace the motherboard
Click to expand...
Click to collapse
I am pretty certain this is a hardware issue. I am calling LG tomorrow and hopefully they'll take the phone for repair/replacement.
I sent my phone for repair. Today I got it back, and guess what?!
The issue is still present! It seems, they "couldn't reproduce" or something.
What should I do now?
EDIT: If anyone is interested, here is a video I just captured which clearly demonstrates the problem. http://youtu.be/38kF9RYs_bU
I'm sending the phone back for repair tomorrow with this video attached.
Hey, might not be an issue at all, but in the video, I saw that the two times you were able to get it to go blank you had your finger on or near the proximity sensor. I wonder if there is something that could be the trigger.
Just wondering if you can duplicated it or cause it only when you have the proximity sensor blocked, or if it truely is random.
You are right, it might has something to do with the proximity/light sensor.
On the other hand, this issue occurs even on incoming calls when the phone is placed on a table, screen up and nothing around the sensor.
Today, I visited my local carrier shop and left the phone for repair again. They told me, since this is a second claim they'll run it through the process faster, so I expect to get it back next week.
Will post an update.
UPDATE: My phone was replaced. Yesterday I got a brand new unit, yeah! It was stock wp 7.0. I plugged in my sim and used the phone the whole day, no sign of blank screen issues. Last nigh I installed all the updates (total 5 I think) up to OS 7.10.8107.79, FW 1.0.16.10. Guess what?! Same issue!
I am crushed
Hello all,
I've been using ZUK Z1 for just about a week now and everything was fine until a couple of days ago when I could not unlock the phone after a call - the power button and the home button turned the screen on for a split of a second and then the screen went off again without reacting to any taps. I had to restart the phone by pressing the power button + the volume down button. I tried to reproduce the issue, but did not succeed.
Yesterday, I had the same issue twice and then I finally got it how to reproduce the problem The main condition seems to be ending the call when the screen is off. That can be achieved by holding the phone close to your ear when the call it ended by the other party or ending the call by pressing the power button (you need to turn on that setting beforehand) again while holding the phone close to your ear.
Another guy on another forum wrote that had experienced the same issue once and yet another guy mentioned that there was such an issue with Cyanogen on OnePlusOne, but it was fixed in one of the updates.
I'm currently on 12.1-YOG4PAS3OH and I'm not sure whether it is a Cyanogen issue alone or an issue caused by interaction of Cyanogen and some of the applications installed. I'm inclined to believe that it's the latter, otherwise there would be a lot of people who ran into the issue.
This weekend, if time permits, I'm going to try uninstalling the applications one by one to find out whether any of them contribute the issue, but maybe some of you have already done some investigation or know how fix the issue. I would appreciate your input.
Thanks.
Hi there, i am facing the same issue since two days now
First i am unable to come up with the physical home button issue and now there is this new issue. The phone does not respond after a call and the screen remains off and does not respond to any touch (double tap) or even the power button and home button pressed. I had to take the mobile into the recovery mode via home buttons power button and volume rockers. Is there any possibility of this getting fixed. I think i made a huge mistake purchasing this phone.. Slowly getting into problems one by one.. First the physical home button issue then this screen off issue. Checking for updates daily but seems like ZUK officials and Cyanogen are sleeping! Highly disappointed!!!!
In the meantime, I uninstalled most of the applications and the issue was still there Then I tried to play with different settings and it seems I have nailed it. After disabling turning on the screen by double tap (I'm not sure how the setting reads in English, I'm using the Russian interface), I cannot longer reproduce the issue.
Sydarij, could you, please, check whether the setting is on in your case and, if it is, turn it off and try to reproduce the issue with the screen?
ingtrans said:
In the meantime, I uninstalled most of the applications and the issue was still there Then I tried to play with different settings and it seems I have nailed it. After disabling turning on the screen by double tap (I'm not sure how the setting reads in English, I'm using the Russian interface), I cannot longer reproduce the issue.
Sydarij, could you, please, check whether the setting is on in your case and, if it is, turn it off and try to reproduce the issue with the screen?
Click to expand...
Click to collapse
Do you mean after turning off the tap to wake option on your ZUK, you are no longer facing such issue?
Sydarij said:
Do you mean after turning off the tap to wake option on your ZUK, you are no longer facing such issue?
Click to expand...
Click to collapse
Yes, that's what it seems. With the option turned on I could reproduce the issue (just 1 or 2 tries were needed), while with the option turned off I could not reproduce the issue at all.
ingtrans said:
Yes, that's what it seems. With the option turned on I could reproduce the issue (just 1 or 2 tries were needed), while with the option turned off I could not reproduce the issue at all.
Click to expand...
Click to collapse
After turning off this feature, the device unlocks by itself without me waking it up. Turning the feature off doesn't seem to help buddy!
Sydarij said:
After turning off this feature, the device unlocks by itself without me waking it up. Turning the feature off doesn't seem to help buddy!
Click to expand...
Click to collapse
This seems to be a different problem. How the option for preventing accidental wake-up is set? (It's just below the double tap option. )
In any case, one owner on another forum complained about the accidental wake-up issue despite the setting was on, but he meddled with the firmware before that...
ingtrans said:
This seems to be a different problem. How the option for preventing accidental wake-up is set? (It's just below the double tap option. )
In any case, one owner on another forum complained about the accidental wake-up issue despite the setting was on, but he meddled with the firmware before that...
Click to expand...
Click to collapse
Yes, the accidental wake up is set yet the issue cannot be resolved. Any other way you can resolve this and prevent the issue from reproducing? In my opinion, ZUK and Cyanogen officials are asleep after launching their new flagship. Dont see any updates coming from them since last 2 months. highly disappointed with this!
Sydarij said:
Any other way you can resolve this and prevent the issue from reproducing?
Click to expand...
Click to collapse
No idea. The solution I found seems to work well for me, at least I have not had any issues since I applied it.
Please turn on adaptive brightness. Issue will be resolved
ingtrans said:
Hello all,
I've been using ZUK Z1 for just about a week now and everything was fine until a couple of days ago when I could not unlock the phone after a call - the power button and the home button turned the screen on for a split of a second and then the screen went off again without reacting to any taps. I had to restart the phone by pressing the power button + the volume down button. I tried to reproduce the issue, but did not succeed.
Yesterday, I had the same issue twice and then I finally got it how to reproduce the problem The main condition seems to be ending the call when the screen is off. That can be achieved by holding the phone close to your ear when the call it ended by the other party or ending the call by pressing the power button (you need to turn on that setting beforehand) again while holding the phone close to your ear.
Another guy on another forum wrote that had experienced the same issue once and yet another guy mentioned that there was such an issue with Cyanogen on OnePlusOne, but it was fixed in one of the updates.
I'm currently on 12.1-YOG4PAS3OH and I'm not sure whether it is a Cyanogen issue alone or an issue caused by interaction of Cyanogen and some of the applications installed. I'm inclined to believe that it's the latter, otherwise there would be a lot of people who ran into the issue.
This weekend, if time permits, I'm going to try uninstalling the applications one by one to find out whether any of them contribute the issue, but maybe some of you have already done some investigation or know how fix the issue. I would appreciate your input.
Thanks.
Click to expand...
Click to collapse
Hi! I'm facing the same issue for the last 3 days. I felt everytime there is any moisture of sweat on the ear piece the phone hangs and doesn't get unlocked.
Will try shutting the double tap options. Hope it works! This is the first time I've brought anything in the launch sale without reading reviews. Hope I don't regret this.
sir when call come rintone accor but calling display doesn,t show
when i press phone icon in menu then it shows
phone is lenovo zuk z1
screen freezes during/after call !!
did you solve this problem?
i too have posted the same problem here ..
any sugesstions?
i am facing a black screen while calling and receiving calls on my zuk z1 .. any solution? and where do i find the proximity setting in my settings?
Hey guys,
i have a serious problem, which happens really often lately. like 10 times a day. The screen just turns off sometimes. The touch-functionality is still working. I can feel the fingersensor "unlock" the Zuk Z1, but the screen just stays off. Then i try to press all the buttons and sometimes the screen turns on again. But sometimes it just turns on after some seconds even though I didn't touch it at all.
First I thought that this is a hardware issue, maybe a loose contact. But recently a new problem showed up. The screen brightness just goes up to 100%. I turned off auto-brightness and move the slider. Nothing happens. Restarting always fixes it. But mostly after 1-60 seconds it goes back to normal.
Any ideas what might be the problem? Or what I could try?
I haven't rooted the phone and its the newest CyOS version.
Cheers, Oliver
Perhaps you are using the flipcover with magnetic auto switch off when you close the case?
OlivBlum said:
Hey guys,
i have a serious problem, which happens really often lately. like 10 times a day. The screen just turns off sometimes. The touch-functionality is still working. I can feel the fingersensor "unlock" the Zuk Z1, but the screen just stays off. Then i try to press all the buttons and sometimes the screen turns on again. But sometimes it just turns on after some seconds even though I didn't touch it at all.
First I thought that this is a hardware issue, maybe a loose contact. But recently a new problem showed up. The screen brightness just goes up to 100%. I turned off auto-brightness and move the slider. Nothing happens. Restarting always fixes it. But mostly after 1-60 seconds it goes back to normal.
Any ideas what might be the problem? Or what I could try?
I haven't rooted the phone and its the newest CyOS version.
Cheers, Oliver
Click to expand...
Click to collapse
Thanks for the reply,
I havent thought of that before but it is not the cause of the problem.
1. I have a leather case
2. When I take the phone out of the case the displays stays dark
I just did a factory reset today in the morning and the problem already showed up again. So! annoying!!!! Will send back the device I guess
i have lenovo zuk z1 . actually i am getting a problem in this phone . after locking the phone at every seconds light turn on and get turn off on the display. i saw so much on the setting but i didnt get any setting .
The same problem is being arrising with me..please someone help. what should i do..