GT-I9505 Little to no wifi signal after camera replacement? - Galaxy S 4 Q&A, Help & Troubleshooting

Like the title says I now have little to no wifi signal unless stood next to the router?
Can anyone help me out am getting really cheesed off with this.
thanks in advance

Checked for loose connectors? Does wifi improve if you remove the cameras?

Was perfectly fine, before I did the camera, checked the conector the little point bit snapped off but not the ful connector so I am still able to lift it up slightly?

Are you referring to the centre pin?

no the little connector on the oppisote side of the bored

located here in the green ring, the whole connector is still attached all tho a little bit on the top has came of no bigger than a half centimeter

Maybe the connector is not making proper contact with the back casing. Maybe add a bit of solder to the gold contact to raise it up a bit to it makes better contact?

Would adding solder not damage it?

Check WiFi Antenna
PhaseCoder said:
Like the title says I now have little to no wifi signal unless stood next to the router?
Can anyone help me out am getting really cheesed off with this.
thanks in advance
Click to expand...
Click to collapse
Sounds to me like the device was opened to replace the camera, and it could be something easy to fix. Fix step open the device, and check that suckers WiFi Antenna wire....looks the same as a Laptop WiFi Antenna Wire, except smaller and shorter, it may be disconnected from the logic board connector location, or the wire is broken or damaged.

Adding a but of solder may work as long as you use low-melt solder, a very fine tip iron, and you do not let the solder flow to other parts of the board.
I suppose the alternative would be taking it to a cell shop to see if they can fix it.

I have Samsung i9505l updated to lollipop via OTA after updating All the sensor stopped what does it mean is Samsung killing their devices via ota's i said to my friends that it's hardware (sensor Hub) problem! and he was saying no it's software problem after downgrading to Kit Kat... everything works fine I lost $30 bet on it.! poor Samsung ! so the main question is there anyway to upgrade to lollipop with working sensors?

http://samsung-updates.com/

Related

Wizard Repair Guide?! Mines Broken :(

Hey Guys,
Well, I'm a bit gutted really! I dropped my XDA Mini S on the floor with the charger in and the connector IN the phone has come apart from inside the phone. The little metal bit is practically hanging out. I'm wondering, if i were to take the phone apart could i re-connect the little part? (I have a soldering iron if thats as simple as its going to be?)
Just wondering if anyone had any guides on how to take the phone apart and take a look at whats wrong?
Any help would be so much appreciated!
Many Thanks,
Tom
The service manual is hosted on the ftp site.
ftp://ftp.xda-developers.com/Wizard/Docs_Tutorials/
Hope this helps.
I suspect you probably broke the socket off, but if you have a soldering iron, you might as well try to get a new mini USB connector to work with.
You might try Pocket PC Techs:
http://www.pocketpctechs.com/main~unit~UTStarcom_XV6700-554~area~repairs~item~REP-USBCON01~name~UTStarcom+XV6700+Mini+USB+Connector+Replacement+Service.htm
I rang them up about an issue I had (screen on the fritz) and they seemed pretty knowledgeable and helpful.
Alternatively there's a company I found today in the UK. I can't vouch if they're good or not.
http://www.xdarepairs.co.uk/home.asp
Good luck.
Well I also have an issue with my wizzard... the mini jack connector (of the handsfree) is a bit loose.
What I am saying is that it does have a good connection with the rest of the circuit and sometimes the sound of the speaker goes off, then I have to insert the habdsfree and tickle it a little bit until it has a good contact.
? have some basic soldering experience,do you think I should give it a try?
Given my device has been apart too many times for me to admit to I thought I'd crack it open to take a pic for you guys. Not sure if this pic will help for those wanting to do some soldering:
Very large pic: http://farm1.static.flickr.com/216/452691530_f47801708f_o.jpg
Excuse the dust.
Ah! That picture at the bottom is exactly what I needed. The metal but at the bottom (the big sqaure) has totally sheared off....bloody thing. Thanks so much for the info on the repair guides. I may give those repair guys a call if i can't get it to work myself.
Thanks alot you guys
As for you WizeMan, it all depends on if you wish to void your warrenty or not. At the end of the day, I installed WM6 on my device so O2 would give me the finger if i tryed to claim. If I'm honest, I'm getting an upgrade next month so I'm not to bothered if I balls it up! Would be nice if I got it working though....
Lemmie know how you get on
unlock k-jam
i read all your write about how to unlock k-jam device but after all i get this message:
Lock Status: 0000000000000000
SIMLock Code: █⌠═eי∟80Γ█Σ☻< δ♠
how can i get it from this .........
lironasseo said:
i read all your write about how to unlock k-jam device but after all i get this message:
Lock Status: 0000000000000000
SIMLock Code: █⌠═eי∟80Γ█Σ☻< δ♠
how can i get it from this .........
Click to expand...
Click to collapse
A little bit of a thread hijack but that means it is SIM unlocked.
Let me tell you my news, my friends.
I opened my Qtek 9100 and fixed two serious issues regarding this phone, using... sponge (the one we use to wash the dishes)
1. I put some into the stylus socket (from the thin space it has) and also
2. On the top of the mini jack socket so when i assembled the housing it blocked it from moving (2 of the contacts are no more soldered and i dint have a soldering iron at that time)
Anyway, both operation went ok and my phone is more than fully functioning. Now the stylus is hardly (in a good way) comming out (it first gets longer then comes out).
I wanted to do also the safe singal fix, but didnt find the photos to apply it correclty, so if someone has them, please give link. If you need any info about the "Sponge" Hacks, just post or pm
WizeMan said:
Let me tell you my news, my friends.
I opened my Qtek 9100 and fixed two serious issues regarding this phone, using... sponge (the one we use to wash the dishes)
1. I put some into the stylus socket (from the thin space it has) and also
2. On the top of the mini jack socket so when i assembled the housing it blocked it from moving (2 of the contacts are no more soldered and i dint have a soldering iron at that time)
Anyway, both operation went ok and my phone is more than fully functioning. Now the stylus is hardly (in a good way) comming out (it first gets longer then comes out).
I wanted to do also the safe singal fix, but didnt find the photos to apply it correclty, so if someone has them, please give link. If you need any info about the "Sponge" Hacks, just post or pm
Click to expand...
Click to collapse
I'm still trying to get the a new fascia and will probably shove an eraser bit into the stylus spring mechanism to ensure the defect never happens. Also how did you discover the break in the solder joints on the headphones jack? I have a funny situation where the left channel of the headphones doesn't work but I suspected the headphones (the plug has to be pulled at an angle to get any sound out of the left) but now I am thinking it may be the socket itself.
By the way the reception fix pic doesn't load for me either but I unless you truly need it, don't waste your time doing it; I always have all 4 bars and sometimes have 2 bars.
AsGF2MX said:
I'm still trying to get the a new fascia and will probably shove an eraser bit into the stylus spring mechanism to ensure the defect never happens. Also how did you discover the break in the solder joints on the headphones jack? I have a funny situation where the left channel of the headphones doesn't work but I suspected the headphones (the plug has to be pulled at an angle to get any sound out of the left) but now I am thinking it may be the socket itself.
By the way the reception fix pic doesn't load for me either but I unless you truly need it, don't waste your time doing it; I always have all 4 bars and sometimes have 2 bars.
Click to expand...
Click to collapse
Allright here is the deal.
1. I found out the break in the soldier joints when i opened it. I was really suspicious about it because when i inserted my headphone jack into the connector, i had problem with the contact; the connector was loose and it muted my phones speaker. When i disassembled the phone using the service manual i saw with my eyes that the the joins where f-ed up.
2. I dont really need the signal hack i just wanted to experiment, i have 2.25.11 cingular radio rom and its great.
Btw i suppose you should better use the sponge, because the rubber may wear off but not the sponge...
Thanks for the tip on the sponge. I am going to grab a used but allegedly "like new" body from eBay and also get one of those covers as well.

[REF] GT-I9300 Service Manual

Here is the Samsung Galaxy S3 (GT-I9300) Service Manual.
Please take a moment to read the notes and issues about this manual in this post.
For some reason Google didn't pick up that post, so I had to re-post here...
Now, if you are brave and happen to have a GT-I9300, you can still help us by posting some
internal pictures, to verify some issues in the manual. If they are good,
some of them will eventually become part of the SGS3 Hack-Pack.
Thanks and Enjoy!
I will be opening up the phone in the next few days due to me managing to damage the sim card holder section(not holding sim card) So at present i have got somthing putting pressure to keep sim card in place. I have a new sim card holder on order so when it arrives i will pull phone apart and take some pictures.
If you have any advice for me before attempting this please let me know via pm
Do you have any experience in this kind of electronics? I mean, are you planning to replace and solder the SIM card holder by yourself?
If you have not done this type of soldering before, I do not recommend it.
If you do decide to do it on your own, make sure:
You are working on a clean workspace
You are well grounded and not wearing wool clothes mixed with synthetic materials to avoid any ESD.
Have the right tools for the job.(Temp controlled SMD soldering iron + flux and acid-free lead-free SMD solder etc.)
A very steady hand with good eyes!
As for the pictures, keep the environment as bright as possible, preferably daylight. Try to keep your PCB on a bright or neutral background. (Bright cardboard is usually good.) Inspect your pictures and make sure you can read the text on the smallest chips. (The big ones we already know about, its the smaller ones that are difficult to navigate around.) Make sure the pictures are well focused.
Good Luck!
From looking at the pictures I was hoping I don't have to solder the sim card slot in. It looks easily replaceable as it looks like it's just a connector and not soldered
Replaced the sim holder. My camera wasn't good enough to get focus of the smaller chips however it is very very easy to take phone apart. And I guess Samsung are expecting issues with sim slot so they have fixed it using one screw and connected to board using a pull off connecter.
Just in case anyone else is interested the sim holder/sd holder cost me £20, delivered.
E:V:A said:
Here is the Samsung Galaxy S3 (GT-I9300) Service Manual.
Please take a moment to read the notes and issues about this manual in this post.
For some reason Google didn't pick up that post, so I had to re-post here...
Now, if you are brave and happen to have a GT-I9300, you can still help us by posting some
internal pictures, to verify some issues in the manual. If they are good,
some of them will eventually become part of the SGS3 Hack-Pack.
Thanks and Enjoy!
Click to expand...
Click to collapse
amazing !!!
Hi guys,
Here is my contribution to da community, hope so it helps.
h t t p s : / / docs . google . com/open?id=0B9lrf7AWQW7ETjRZTkFXb1luN0E
On image 20120616_150200.jpg you can see the region jumpers. The images are of a live demo unit - everything works besides the GSM/3G data. Haven't tested to see if the NFC is working.
The real unit has some more antenna connector. The demo one does not have PBA /printed board antenna/ the ANT102 and ANT103 as well as the capacitors and the coils u may seen them market in red cycles (ANT102, ANT103, C102, C191, L103, L102) there is no room on the MOBO for C192 /or at least I can't find its place/.
Thanks.
^^ Here is the link for above! (Thanks!)
Hi again,
I can confirm that the NFC is working on the live demo unites. According to the original S3 user manual the NFC antennas are build into the battery back.
I still can't figure out what is the "W2" antenna connector for. The Live demo unit has no connector soldered to the motherboard and also lacks the small PCB antenna with the white coaxial cable. Some ppl claim that the W2 is for WiFi antenna, but it is not, because I got great WiFi connectivity tho the lack of such PCB antenna. I can only confirm the WiFi working fine, under "G" type of WiFi networks. The openWRT firmware of my current router has known bug and I can't bring up "N" standard in air, to check if the PCB antenna is for "N" type of WiFi networks.
I also did some testing to see if the PCB is for GLONASS or GPS, and it seams that this PCB antenna with the white coaxial cable is not for any of these services. That's why I think it might be for wifi "N" or 3G data/networks. Donno if the 802.11n requires a separate antenna.
^^ Please post a link to a specific image, that clearly show the connector(s) you're talking about.
Hi I have a live demo unit to, so I think I can help about this =).
I can't show you the mainboard back because I' m new user... xD
I don't really know what you mean with NFC (sorry, I'm not really good with english)
But
W1 is a GSM external antenna conection
W2 is a wifi external antenna conection
And the white wired antenna is for wifi to.
After thinking a lot, if you conect an antenna to the GSM antenna conection (external or the internal lacked in Demo unit) you probably can't use phone function.
That function probably was crippled by software or because demo units don´t have imei maybe o.o.
The only thing I need to try is to connect a microsim to the phone
No one has any insights ???
johnny21a said:
No one has any insights ???
Click to expand...
Click to collapse
I have sgs3, international version on my workbench right now.
Don´t have any clue what could I share, so - if there is anything specific -- let me know. I will do my best..
BR
Samsung galaxy S3 i747
i have a Galaxy S3 SGH-i747m that has been water damaged and given to me so i could try and fix it. I can take pretty much any pictures you want, have openned the phone a couple times now to try and clean it up.
My problem is that the works well, it starts up, unlock the screen, plays sound...but the screen is off. Now at first when i was "playing" with it the screen would flicker on and off to show me the battery charging logo when it was plugged in. I've cleaned the phone and all flex connectors with some products. the phone still turns on and works but my screen is off. It detects the touch since i can unlock the screen ( it plays the water sound when i slide my finger on the screen) and speaker works when i boot it up (little booting sounds).
I was thinking there might be a small fuse on board for the screen backlight and that could be blown. I was also thinking my battery might be damaged and is not giving the phone the right voltage to the right connectors or something so i have ordered a new battery on ebay (under 4$) and am waiting for it.
Anyone has an idea to some specific things i should be looking for ? only thing haven't disassemble is the digitizer from the framebecause doing so would surely break the glass. It bums me up a bit since there are some electronics behind the frame that could have been damaged by the water that i couldn't see.
Bigred065 said:
i have a Galaxy S3 SGH-i747m that has been water damaged and given to me so i could try and fix it. I can take pretty much any pictures you want, have openned the phone a couple times now to try and clean it up.
My problem is that the works well, it starts up, unlock the screen, plays sound...but the screen is off. Now at first when i was "playing" with it the screen would flicker on and off to show me the battery charging logo when it was plugged in. I've cleaned the phone and all flex connectors with some products. the phone still turns on and works but my screen is off. It detects the touch since i can unlock the screen ( it plays the water sound when i slide my finger on the screen) and speaker works when i boot it up (little booting sounds).
I was thinking there might be a small fuse on board for the screen backlight and that could be blown. I was also thinking my battery might be damaged and is not giving the phone the right voltage to the right connectors or something so i have ordered a new battery on ebay (under 4$) and am waiting for it.
Anyone has an idea to some specific things i should be looking for ? only thing haven't disassemble is the digitizer from the framebecause doing so would surely break the glass. It bums me up a bit since there are some electronics behind the frame that could have been damaged by the water that i couldn't see.
Click to expand...
Click to collapse
check if you can see anything on the screen, use some extra light, torch for example.
if so - then its more likely that the LEDs in the display panel are damaged, since it flickered, as you said. also could be the driver circuit for backlight. Clean connectors for display panel, use magnifier, or better microscope to check for corrosion. use IPA to clean or scrape off the corrosion.
also - maybe this is not the right place to discuss this.
GL
Redrigon said:
Hi I have a live demo unit to, so I think I can help about this =).
I can't show you the mainboard back because I' m new user... xD
I don't really know what you mean with NFC (sorry, I'm not really good with english)
But
W1 is a GSM external antenna conection
W2 is a wifi external antenna conection
And the white wired antenna is for wifi to.
After thinking a lot, if you conect an antenna to the GSM antenna conection (external or the internal lacked in Demo unit) you probably can't use phone function.
That function probably was crippled by software or because demo units don´t have imei maybe o.o.
The only thing I need to try is to connect a microsim to the phone
Click to expand...
Click to collapse
I don't have he white antenna coaxial cable neigh the PCB antenna board that this cable is connected to but I have WiFi.
Could it be for WiFi N(150Mbps)?
Watter damage, LCD working/not working?
Bigred065 said:
i have a Galaxy S3 SGH-i747m that has been water damaged and given to me so i could try and fix it. I can take pretty much any pictures you want, have openned the phone a couple times now to try and clean it up.
My problem is that the works well, it starts up, unlock the screen, plays sound...but the screen is off. Now at first when i was "playing" with it the screen would flicker on and off to show me the battery charging logo when it was plugged in. I've cleaned the phone and all flex connectors with some products. the phone still turns on and works but my screen is off. It detects the touch since i can unlock the screen ( it plays the water sound when i slide my finger on the screen) and speaker works when i boot it up (little booting sounds).
I was thinking there might be a small fuse on board for the screen backlight and that could be blown. I was also thinking my battery might be damaged and is not giving the phone the right voltage to the right connectors or something so i have ordered a new battery on ebay (under 4$) and am waiting for it.
Anyone has an idea to some specific things i should be looking for ? only thing haven't disassemble is the digitizer from the framebecause doing so would surely break the glass. It bums me up a bit since there are some electronics behind the frame that could have been damaged by the water that i couldn't see.
Click to expand...
Click to collapse
I have identical symptoms with my i9300.
1. Water damaged
2. Dried in a can of rice etc over several days
3. Cleaned under sim card, lots of debris there, looked scorched, I cleaned with alcohol and a brush in an ESD protected environment.
4. Re assembled, the display briefly flashed on, and showed the expected "Battery is low, an d No Sim Card" then powered off.
5. Now after charging the battery and emplacing my sim card, I hear the proper musical tones when the phone boots but the screen doesn't light.
Where you able to get the screen working?
I am going to try a more throughal cleaning and I will try viewing the LCD under a more power full light.
I too worry that just getting the LCD screen replaced might not work; the screen may be fine but the mother board LCD power supply might be at fault...
I will keep you posted and keep an eye on this forum to find out how to fix this.
This thread has served its main purpose.
OT discussions are prevalent.
Thread Closed!

Disable Internal Antenna Permanently

I want to permanently disable my Samsung Galaxy S4's internal antenna. I know doing this seems a bit unorthodox but I have my reasons why I want to do so. I will be connecting an external antenna via the L1 port using a patch lead cable. No I don't want to use the internal antenna ever so I'm wondering how it can be disconnected; I don't want any responses asking me why I want this to be done I just want possible solutions. I was wondering if I could open the phone and somewhat remove the antenna or mess with the antenna contacts so it could stop working I'm not sure though so I need either a hardware or software solution.
The antenna is simply a wire running down the side of the battery compartment. Open the S4, disconnect that wire, and you should be able to achieve what you want.
Just one thing. Telling people you don't want questions as to why you're doing this is inevitably going to lead to people asking questions as to why you're doing this. In the future, if you don't want to pique people's curiosity, either come out and say why you're doing it, or don't make such an announcement.
Strephon Alkhalikoi said:
The antenna is simply a wire running down the side of the battery compartment. Open the S4, disconnect that wire, and you should be able to achieve what you want.
Just one thing. Telling people you don't want questions as to why you're doing this is inevitably going to lead to people asking questions as to why you're doing this. In the future, if you don't want to pique people's curiosity, either come out and say why you're doing it, or don't make such an announcement.
Click to expand...
Click to collapse
Okay thanks I will get a technician to pull the device for me. The reason i am doing it is that I am electrically sensitive...WiFi...cell signals they make me sick. The condition is relatively rare in some countries but it's increasing worldwide. Most times when I mention it to people that I am a 22 yr old electrically sensitive software engineer there's so much skepticism and ridicule because most people don't believe in the harmful effects of wireless radiation because they haven't experienced it first hand.
So my aim is to disconnect the internal antennae, then have an external one that's a good distance away that I connect to my device so I can use cell services without the radiation affecting me. I have a radio frequency meter that I use to measure the signals.The source of radiation is from the antennae so I have all other wireless features disabled and I would like to use this particular one that I can isolate/control.
If it makes you sick, that's understandable. If you want to do it yourself and not bother with the tech, taking the back off to get to the antenna wire is a pretty easy task. Nine screws and popping a tab or two and the back comes off. In your case, you want to completely remove the wire from the device as even if it's disconnected on one end, the other end may still be able to transmit. The wire snaps in at both ends, so again, it's a simple thing to do.
Alright thanks for the info. I don't have the screw driver so I guess I will have to make a technician do it. I am all the way in Jamaica so it's easier to go to a tech than to ship a small package here. I know about the antenna wire but I am wondering if its the only antennae ( apart from the WiFi, bluetooth etc. that can be disabled ) because I saw on a website a picture of the insides and there are two antenna contacts at the top that connect to an antennae thats on the shell. So is this wire the sole antennae mechanism for the GSM?
Honestly, I don't know.
joeldean said:
Alright thanks for the info. I don't have the screw driver so I guess I will have to make a technician do it. I am all the way in Jamaica so it's easier to go to a tech than to ship a small package here. I know about the antenna wire but I am wondering if its the only antennae ( apart from the WiFi, bluetooth etc. that can be disabled ) because I saw on a website a picture of the insides and there are two antenna contacts at the top that connect to an antennae thats on the shell. So is this wire the sole antennae mechanism for the GSM?
Click to expand...
Click to collapse
hi mate ,
The wire connects the antenna at the bottom to the module where the GSM/EDGE , WIFI , BT, etc chips are , that cable seem to be the only physical connection between the antenna and the respective controlling chips
Check here , steps 13 , 14 and 15
https://www.ifixit.com/Teardown/Samsung+Galaxy+S4+Teardown/13947
@MAX 404: I couldn't remember whether that was the case or not. I had other things on my plate.
Strephon Alkhalikoi said:
@MAX 404: I couldn't remember whether that was the case or not. I had other things on my plate.
Click to expand...
Click to collapse
Hi mate ,
You cover planty my friend , you are a big help around here :good::good:

Sony Xperia Z3C GPS FIX - an Hardware problem

Hi all,
during these months I have had a lot of problems with GPS Fix with my Z3C. These problems occurred after the update to 6.0.1 and I thought that It was a software issue.
In my case, GPS works well after upgrade but It degraded little by little. Applications like GPS Status reported a very very low satellite signal.
Reading every possible forum, I found some guys that explain how to "solve" the problem plugging the usb and powering the phone. An other post specified that the solution was not the "powering" and the fix become better if you lightly pulling the usb connector to you... and It was true! So the problem was not software.
So I opened the phone, disassembled the mainboard from the chassis and tryed to understand what part was involved in the "usb pulling solution".
I found that many connectors (like a little pin) were connected to some particular parts to the chassis (as if it were used as antenna).
In this photo you can see where the mainboard connectors impact on the chassis.
(Sorry the forum prevent me to post link or image)
And this is the specific connector involved in "usb pulling solution"
(Sorry the forum prevent me to post link or image)
It seem that this connector was linked in the edge of connection area, not in the middle as the other connector.
So I gently bent the connector upward and reassembled the phone.
After that, the GPS Status reported a signal very high. Never seen a signal so hight before!
The fix was very fast and the accuracy was constantly under 3mt
I'm not an expert, I'm only a normal user. I hope that this thread can help some other like me that need GPS works very well for run, drive and play.
Thank you for this post - I've been fighting with my GPS for months and am about ready to open up the phone too. Any chance you could post the images externally somehow? It would make this a lot easier to follow for me.
Wulfhere said:
Thank you for this post - I've been fighting with my GPS for months and am about ready to open up the phone too. Any chance you could post the images externally somehow? It would make this a lot easier to follow for me.
Click to expand...
Click to collapse
I'm trying to post images but the forum reply me in this way:
"To prevent spam on the XDA forums, ALL new users prevented from posting outside links in their messages. After approximately 10 posts, you will be able to post outside links. Thank you for understanding!"
I'm asking to the moderatos if is possible to unlock me.
I will let you know
Anyway... start watching "sony z3 compact disassembly" on youtube. You need some tool to do this without destroy the phone. But trust me, is not so difficult. In particular, take care about the battery door opening.
gepp81 said:
I'm trying to post images but the forum reply me in this way:
"To prevent spam on the XDA forums, ALL new users prevented from posting outside links in their messages. After approximately 10 posts, you will be able to post outside links. Thank you for understanding!"
I'm asking to the moderatos if is possible to unlock me.
I will let you know
Anyway... start watching "sony z3 compact disassembly" on youtube. You need some tool to do this without destroy the phone. But trust me, is not so difficult. In particular, take care about the battery door opening.
Click to expand...
Click to collapse
Just add a few 'well done Mr Developer' messages to a few threads, you'll soon get to ten
great news waiting for photos, maybe link to photopucket or something ?
Nice you've fixed it yourself!
gepp81 said:
It seem that this connector was linked in the edge of connection area, not in the middle as the other connector.
So I gently bent the connector upward and reassembled the phone.
Click to expand...
Click to collapse
I've already disassembled a plenty of Sony phones (from Xperia X10 pretty much to every single later Sony phone that was available in Poland) and the issue with bent connectors is very very common. I also had this problem in my Xperia PLAY where my WiFi and cellular network connectors were bent and were linked on the edges of the plates.
ALL Connectors
https://www.dropbox.com/s/pgldca344e3h7be/WhatsApp-Image-20160710.jpeg?dl=0
GPS Connector
https://www.dropbox.com/s/egh4vjmpt96qdzp/WhatsApp-Image-20160710%20%281%29.jpeg?dl=0
romcio47 said:
Nice you've fixed it yourself!
I've already disassembled a plenty of Sony phones (from Xperia X10 pretty much to every single later Sony phone that was available in Poland) and the issue with bent connectors is very very common. I also had this problem in my Xperia PLAY where my WiFi and cellular network connectors were bent and were linked on the edges of the plates.
Click to expand...
Click to collapse
Do you have a connectors map?
Hell. I had the same problem : suddenly the GPS signal became very weak, almost unable to catch any satellites and degrading over time, so since I still had 1 month warranty I sent it to the repair center and they changed my PBA (which is the motherboard, I believe.) It is now working like a champ again. If I were to get the problem back in a few month, after my warranty expiration, I'll definitively try to do what you did.
Thanks for the info.
gepp81 said:
Do you have a connectors map?
Click to expand...
Click to collapse
Unfortunately, no... but I recommend visiting iFixit site where some of the phones are nicely described.
Thanks a milion gepp81!
I ve ordered some replacement parts and tools and I will try to resurrect my z3 gps.
Yarymo said:
Hell. I had the same problem : suddenly the GPS signal became very weak, almost unable to catch any satellites and degrading over time, so since I still had 1 month warranty I sent it to the repair center and they changed my PBA (which is the motherboard, I believe.) It is now working like a champ again. If I were to get the problem back in a few month, after my warranty expiration, I'll definitively try to do what you did.
Thanks for the info.
Click to expand...
Click to collapse
Same with me.
I believe that since we got a new imei number e got new warranty. I have to check the law.
Enviado do meu D5803 através de Tapatalk
Can anyone confirm this please? It looks weird to me. According to service manual all antenna connectors are on secondary side of mainboard (accesibble without removing battery, just after opening rear cover and removing that frame around, which has 4 screws, if I remember correctly).
It works
IkE Blaster said:
Can anyone confirm this please? It looks weird to me. According to service manual all antenna connectors are on secondary side of mainboard (accesibble without removing battery, just after opening rear cover and removing that frame around, which has 4 screws, if I remember correctly).
Click to expand...
Click to collapse
It works. All the connectors are on one side of the motherboard (not the battery side). The picture gepp81 posted shows the antenna area where the connectors connect to, so not the actual gps connector.
Thanks a lot!
I had absolutely no GPS signal.
After trying every software tweak / wipe / rom.... (I was hopping it was a software issue) I finally tried your solution, straighten all the little contacts, and now my GPS has a wonderful signal!!!
I destroyed my back cover, but it doesn't matter I prefer that than no GPS
Wow, thank you. I can also confirm this. Despite that official service manual says something different.
Previously zero signal at all (23 satellites with 0 SNR), sometime 1 very weak satellite. Now 9 fixed, another 6 visible. Those 15 doesn't have very strong signal, but it's usable.
I am thinking about using some thin wire to improve it (like this: https://talk.sonymobile.com/t5/Xperia-Z3-Compact/GPS-issue/m-p/1006245/highlight/true#M12642 ).
Another successful story here - gps stopped working, i updated my rooted kitkat to slimm 2.4, opened phone, did the connectors trick, but gps was still dead. Then after few days i checked "Device only" in Location settings and GPS came back to life! Now works with "High accuracy" mode as well
lakicamm said:
Another successful story here - gps stopped working, i updated my rooted kitkat to slimm 2.4, opened phone, did the connectors trick, but gps was still dead. Then after few days i checked "Device only" in Location settings and GPS came back to life! Now works with "High accuracy" mode as well
Click to expand...
Click to collapse
Also had problems with my gps. First I thought it was water damage. But pulling with the usb connector made it work again.
Did the trick with bending the connector. Now I have signal but is is not very strong.
Is there a way to make the signal stronger?
Is the copper strip the antenna?
Can I replace this with another copper strip that works as a better antenna?
Or .....?
If your gps antenna is somehow damaged, you could fix it using silver paint:
http://www.2spi.com/category/silver-paints-pastes/
I didnt try it, but friend of mine uses it to fix broken boards on laptops... Should work in phones too
Same problem. I sent my phone to service. They changed motherboard. Now GPS Works perfect. And my warranty is extended for 2 years, because of different motherboard and IME. Thanks Sony, very good service

Wifi/Gps/GSM signal strenght issue [Almost FIXED]

Hey guys. Here are a probably fix for wi-fi/sim/gps signal strenght problem after changing the touch or anything similar that needs to disassembly the Mimax2. Well, i found 2 solutions for the problem, but i need someone that understand about hardware to help us. The problem begins when you disassembly the phone, and the pins of the antenna dont plug correctly at the back of the phone. Here are the First solution (that didn't works for me, but maybe works for you):
The video is based in put on the pin a tinfoil to improve the connection with the back cover. I guess that the contact in back cover of my MM2 is very weak, so didnt work for me.
The solution number two is based in connect a copperwire on the pins or on Motherboard to make a homemade antenna. Maybe this way work for me and for who dont have success in the First guide. But as i said previously, i need someone to say If the connections in the pics are correctly. Those pics was found in a telegram group. Some guy made and send them.
Well, if anybody here help me, i'll probably make a video solving the problem. That may help a lot of people having the same problem (they think is a ROM issue, but isnt). I Just need to know where EXACTLY i have to plug the copperwires (fear of burn some peripheal) , and do the tests.
This is ridiculous. Just peel the old antenna out of the old screen, separate the new screen, and put the real antenna in.
You might ask, what is the antenna? Well, there's actually two in one piece of the phone. It's a sticker that the two gold contacts on the original screen were on. The main body is behind the glass, stuck to the plastic. Carefully peel those ends with the gold contact pads up, then from the other side, peel off the sticker they are a part of. The holes are there in all the screens, you just need to carefully push the ends back through with tweezers, then re-glue the glass to the plastic.
It's not easy, but it's not a copper wire hanging out of your phone either.

Categories

Resources