I've been trying to fix this sheet for 4 hours now.
Galaxy S4 sgh-i337
5.0.1
Odin stopped working in the middle of the firmware upgrade and when I turn the phone on says ""Firmware upgrade encountered an issue..."" and tell to use Kies.
F***** Kies doesnt support Galaxy S4 sgh-i337.
I tried to fix with Odin again, with AP, I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5 but it fails.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
about to give up, any ideas?
Is that the same firmware you tried before?
Pwnycorn said:
Is that the same firmware you tried before?
Click to expand...
Click to collapse
I think it is a different one.
First one I tried also didn't work : ALL_ATT_I337UCUFNB1_I337ATTFNB1_505595_REV06_user_low_ship_MULTI_CERT.tar.md5
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> sbl1.mbn
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> boot.img
Use the BL/Bootloader slot in Odin and try again.
Related
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_VZW_G900VVRU1ANCG_G900VVZW1ANCG_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
All flashes fail. Full Tar,Firmware,Kernel, etc...
Just want phone to work again rooted or not, kitkat, lollipop, whatever...
Plz Help =)
beagler89 said:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_VZW_G900VVRU1ANCG_G900VVZW1ANCG_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
All flashes fail. Full Tar,Firmware,Kernel, etc...
Just want phone to work again rooted or not, kitkat, lollipop, whatever...
Plz Help =)
Click to expand...
Click to collapse
What happened to cause you the need to odin to NCG?
Are you using the original data cable? Try a different USB port. Try a different version of odin.
Tulsadiver said:
What happened to cause you the need to odin to NCG?
Are you using the original data cable? Try a different USB port. Try a different version of odin.
Click to expand...
Click to collapse
Yes original cable
Tried to revert back to kitkat, it passed. Now it goes to Samsung Splash Screen then reboots to recovery.
All flashes end the same way, from any version. Have factory reset and everything else.
Nothing will pass.
What is/was the FW you were on before using Odin?
Dudash said:
What is/was the FW you were on before using Odin?
Click to expand...
Click to collapse
OC4
beagler89 said:
OC4
Click to expand...
Click to collapse
Download and flash the OC4 .tar from sammobile.
anyone can help me I'm having this problem
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910HXXU2COJ4_N910HOLB2COJ2_N910HXXU1COJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> modem.bin
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
recovery mode E: Data cannot moount.
help ....
my galaxy note 4 n910h
andre.borba007 said:
anyone can help me I'm having this problem
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910HXXU2COJ4_N910HOLB2COJ2_N910HXXU1COJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> modem.bin
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
recovery mode E: Data cannot moount.
help ....
my galaxy note 4 n910h
Click to expand...
Click to collapse
Make sure that you've checked these:
1) Tried with a different cable.
2) Tried with a different USB port.
3) Make sure ODIN is running as admin in order to minimize software conflicts.
4) Reinstalled Samsung USB drivers.
LTE-X said:
Make sure that you've checked these:
1) Tried with a different cable.
2) Tried with a different USB port.
3) Make sure ODIN is running as admin in order to minimize software conflicts.
4) Reinstalled Samsung USB drivers.
Click to expand...
Click to collapse
Thanks
Hello, my phone stocked on bootloop and i try to flash it to stock firmware and odin fails
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I also try to factory reset it and it is still in bootloop
Please someone help me. Thanks a lot
louellgat said:
Hello, my phone stocked on bootloop and i try to flash it to stock firmware and odin fails
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I also try to factory reset it and it is still in bootloop
Please someone help me. Thanks a lot
Click to expand...
Click to collapse
Hi,
I have reported this thread to be moved to the right Q & A section where you might be able to get help quickly.
Good luck.
I have a Tab S2 SM-T813 that Im trying to reset it keeps giving me an error.
I tried the original cable and many different cables still gives an error
please help!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1101)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> __XmitData_Write
<ID:0/004> Complete (Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
wickedblue2007 said:
I have a Tab S2 SM-T813 that Im trying to reset it keeps giving me an error.
I tried the original cable and many different cables still gives an error
please help!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1101)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> __XmitData_Write
<ID:0/004> Complete (Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Click to expand...
Click to collapse
That error is almost always a bad cable or one that is too long or a bad port.
It might also be worth redownloading the firmware.
If you still have issues then I suggest rooting and using Flashfire to install the firmware.
Hi to all i have the samsung j3 (J320M J3xlte) whit los 14.1 and tried to revert into stok rom but i flash te firmware ARO (J320MUBU0ARD1_J320MUUB0ARE1_J320MUBU0ARB1) and get this error
Odin log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> J320MUBU0ARD1_J320MUUB0ARE1_J320MUBU0ARB1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> nvitem.bin
<ID:0/004> param.lfs
<ID:0/004> PM_sharkl_arm7.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and see this message in the phone: ´´Firmware upgrade encountered an issue. please select recovery mode in kies and try again´´ but also kies and smartswitch dont detect my phone y tried whit anoter firmware and get te same error in odin
i need help and sorry for my bad english