Keyboard cleaning
Anybody tried to clean the keyboard thoroughly?
More and more keys starting to react badly on presses (e.g. no reaction first time.. but my pressing the key again a bit harder it does work).
Looks like there has gotten some dirt underneath.
Advice is appreciated!
Arnie
I take the hose of the shop vac to my keyboard, and around the outer edges of the screen and keys every now and then, making sure not to scuff the device, then hit it all with canned air, no problems as of yet.
Im on this thing 24/7, so it see's some major useage, infact half of my keys are missing paint, and one has a chipped edge, from my thumbnails, but no dirt buildup, which I had been expecting, this house is big time dusty around here.
If anyone does use either of these methods for cleaning, I advise to be cautious around the mic and speakers, I imagine direct strong pressures either way arent too good for them, I do blow them out a bit, but I dont hold the canned air straw right up against them.
This is pretty tame and i am probably just a retard for not figuring this out early, but i thought id share it with you.
You know the annoying edges of the screen that seem to gather so much crap and are hard to clean? I just started using the little cotton buds you clean your ears with to get to the corners and it works really well. No risk of damaging screen and gets right in under the plastic if you push down softly and twist it. cheap and easy to find too.
Also to clean the keyboard i use a little can of compressed air i got from local electronics shop, works a treat to fix any buttons that are not activating properly.
Just thought id share...
Try using a compressed air canister (gently!). I found my wife hidden under my PC's keyboard like that.
V
I cracked my aria screen pretty much right after I got it, Managed to get my hands on a new digitizer and replaced it. I found a quick walkthrough on Android forums. It helped but had a few points that could have been more succinct.
Posting here in case anyone needs.
Took me about an 1hr 30min the first time trying to figure it out on my own.
My additional comments are indicated by **.
I put some addendums to @Jcawesome's steps...
( http://androidforums.com/1211507-post42.html )
1. Remove backcover
2. Remove Battery, sim chip, and memory card
3. Unscrew the top two screws (meaning the end farthest from the memory card.)
4. Using a flat plastic wedge, (I used the one that came from my ebay order, it looks like the blue tool in this pic )
5. Carefully pull off the parts at the top being very cautious not to break anything. (Do not pull the circuit board out, only lift the end closest to the edge of the phone)
** there are two pieces to pull off....with the phone laying flat (screen down and the top facing away from you) a larger yellow piece with an attached back speaker comes out towards you. a second piece pulls up (north as if on a map)... but becareful because there is a bunch of tape and tackiness all throughout this thing (literally I felt it was held together by tape). I actually pulled off the grill on front as well.
** the circuit board is kept attached near the top right. the element that is the power button snaps off. (there are two little dots just to the right of the speaker with what looks like blackish tape that connects to the circuit board... you can pop this off.
With that off, I could lift the circuit board about 30 degrees or so... I wasn't comfortable pulling it back any farther than that.
I did step 5 AFTER I got the screen off.
6. Using the flat plastic wedge again, push the wedge tool between the phone and the broken screen. (It will feel like you are breaking it but it is fine, it is held on by a sticky paste that will slowly give way)
** careful on this part... especially difficult depending on how your screen is cracked. but it is just a bunch of sticky tape that is keeping it attached.... I had to peel away the goo and connection near the top sensitive areas as my ear piece speaker came off with the goo.
7. Disconnect the connecter from the old digitizer to the new one and remove the old digitizer.
**I used a small little tweezer and sneaked it in underneath the circuit board to pull the digitizer connection out.... a little difficult to push back in, but just took some patience.
8. Being careful not to put fingerprints on any exposed surface of either the phone lcd or the replace screen, place the new digitizer in the exact spot of the old one.
** have some lint free microfiber cloth handy and perhaps some screen cleaner.... I spent about 15 minutes cleaning the lcd screen before laying the replacement digitizer back on.
I actually did step 9 before step 8.
9. Connect the connecter from the new digitizer to the board, be careful not to pull the circuit board out and do not scratch the board.
10. You may want to use some glue to hold the new screen on, hopefully this will not happen again. My phone still had enough of the sticky paste left to hold the new screen fine.
** I agree... the first time you replace it will be fine.... afterwards tho, I can see it running out of tackiness.....
11. Put the phone back together in reverse order.
12. Turn it one and everything should be working again.
** in a nut shell
1) take out two screws
2) detach two yellow shell pieces
3) unhook a latch that is the power button
4) pry off the screen
5) lift the circuit board approx 30 degrees.
6) detach digitizer connection from underneath using tweezer
7) replace digitizer connection, return circuit board flat
8)position digitizer and press down to adhere
9)replace two plastic yellow shell pieces
10) screw it back together
done.
let me know if you have any questions.=)
enjoy your "brand" new aria.
dude,, this is a PITA,, I did,, was about 1hour, the hardest part,, is to not put the fingers on the LCD and cleaning the new screen..... dust particles everywhere... and at the end still got one...
Sorry eortizr, If I made it seem easier than it was. I spent quite a while cleaning the lcd screen when I replaced the digitizer... I don't think it's possible to change the digitizer without getting fingerprints on it though. But with some diligence and working in a clean area, I was able to keep all dust and finger prints out of the final product.
My wife dropped hers. Cracked up pretty good but still functional. Think I might just go ahead and pay the $100 and have someone who does it for a living do it.
I can totally see me trying DIY concentrating real hard dripping sweat all over it and ruining the MB. LOL
Replaced the screen today. Half way in I thought I definitely bit off more than I could chew. I got it done though. A couple of things I learned:
The digitizer unplugs away from you or toward the screen with the phone laying flat (screen down and the top facing away from you). I kept thinking i had to unplug it by pulling it north, toward the top of the phone.
I dropped and threw away both the front speaker and the very small rubber piece that covers the proximity sensor so... when I turned the phone on everything looked good, until I answered my phone. The screen went blank and I couldn't hear anything. I found the speaker and the proximity sensor cover and replaced them.
I would do it again, its worth saving $50 or so.
Thanks for the tutorial dreamflux.
I found the whole kit including the adhesive here: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=180643624141
This is the seller in case the sale ends and the link breaks: http://myworld.ebay.com/chinaphoneaccessories/?_trksid=p4340.l2559
I found a replacement digitizer from tmart dot com for $55, free shipping. Just search Aria on their site, you'll find it. Sorry, I can't seem to post links yet.
What was peculiar, was that it has only the HTC logo in the center, and no ATT logo. Looks nice and clean. They included plastic separator tools and torx drivers, though nothing in this phone uses torx. The site is a little shady, and while their headquartered in Hong Kong, it shipped from Brooklyn NY about 5 days after purchase, priority mail. The swap wasn't bad, but my only complaint is that the lights from the softkeys seem to shine up onto the screen, but you get used to it. It's probably because I didn't transfer the stickers over on the bottom of the digitizer.
Thanks for the directions ... I just replaced my digitizer. I had 2 major problems: 1) my power button doesn't work any longer (I'm going to take it apart and try to put it back together and see if that fixes it), and 2) you HAVE to use BLACK sticky stuff to seat the bottom of the digitizer - I used the clear stuff that came with the digitizer, and now I have tons of light bleeding into the LCD from the button backlights. I'm not sure what to do about the bleed ... I guess I'll have to tear it down again and put black stuff in ... damn.
That's the deal with that excess backlighting! I thought it was just a matter of the screen being misaligned. Terrible that I have to replace that black foam, it got shredded while I was dismantling the thing to replace the digitizer.
eortizr said:
dude,, this is a PITA,, I did,, was about 1hour, the hardest part,, is to not put the fingers on the LCD and cleaning the new screen..... dust particles everywhere... and at the end still got one...
Click to expand...
Click to collapse
its always suggested to work in a dust-free space but we all know that's virtually impossible.
I had a bit of fun with dust & fingerprints when replacing my LCD after getting my Aria, After a time or two of taking apart and being unsuccessful, I left it as is with one visible flake.
If you take a hot shower the steam in the air sticks to dust particles leaving no dust
Sent from my Liberty using XDA App
aria
use electrical tape to cover up the lighting that comes through the digitizer
use 3m double sided tape to hold digitizer to lcd
use rubber gloves to change screen to not get finger prints on it
dust906 said:
use electrical tape to cover up the lighting that comes through the digitizer
use 3m double sided tape to hold digitizer to lcd
use rubber gloves to change screen to not get finger prints on it
Click to expand...
Click to collapse
*Just to make sure I'm putting the electrical tape on correctly*
put the double sided tape on and then put the electrical tap (sticky side facing up) on top of the ds tape then apply the screen to the lcd
Thanks for the explanation dreamflux.. This, along with some youtube videos helped me out to change the digitizer, but patience is THE key...
Brought my phone with me to Cedar Point the other day. Survived the entire day....until I stopped at the bars on the way home. Got out of the car, forgetting I had my phone on my lap---shattered right by the track pad.
Just got my digitizer today for $22 on ebay (not bad) After 2 hours and a migraine later, everything came out great.
The only 2 things wrong now are the light from the softkeys bleeding onto the screen and out the sides (I'm just going to shut those lights off), and the trackpad sits a little lower than the screen now. Either I didn't align it right, or the glue isn't holding well. It's weird, if you press on the glass anound the trackpad, it wakes the phone (cm7 trackpad wake).
I only plan on using the phone for a few more months, so I'm happy with the results.
Uhhggg, did the replacement on my son's Aria. It wasn't so bad, but now the LCD screen doesn't light.
I get the vibration when you first hit the power button. Is this correct? I'm not too familiar with the phone.
Rececked the connector for the LCD and it seems to be snapped in.
brivette007 said:
Brought my phone with me to Cedar Point the other day. Survived the entire day....until I stopped at the bars on the way home. Got out of the car, forgetting I had my phone on my lap---shattered right by the track pad.
Just got my digitizer today for $22 on ebay (not bad) After 2 hours and a migraine later, everything came out great.
The only 2 things wrong now are the light from the softkeys bleeding onto the screen and out the sides (I'm just going to shut those lights off), and the trackpad sits a little lower than the screen now. Either I didn't align it right, or the glue isn't holding well. It's weird, if you press on the glass anound the trackpad, it wakes the phone (cm7 trackpad wake).
I only plan on using the phone for a few more months, so I'm happy with the results.
Click to expand...
Click to collapse
did you have any problems with the digitizer responsivenes or something like that? I'm need one and curious about the quality of the cheap digitizers in ebay.
so I replaced my friends screen and now the phone turns on, has sound, vibrates, but just doesnt turn the screen on... the light sensor works and all, and if I call it, it rings and everything, just the screen won't turn on it stays black... I've checked the 2 ribbons and everything is fine, anyone have a suggestion..??
jdmsohc22 said:
so I replaced my friends screen and now the phone turns on, has sound, vibrates, but just doesnt turn the screen on... the light sensor works and all, and if I call it, it rings and everything, just the screen won't turn on it stays black... I've checked the 2 ribbons and everything is fine, anyone have a suggestion..??
Click to expand...
Click to collapse
so what I meant was the digitizer turns on, but it is just a dark lit screen, no visual anything going on.. If i call it from another phone it will ring, but when i swipe right to left to answer and press around where the answer button is it doesn't respond either, just rings and rings... anyways just wanted to elaborate a little more..
---------- Post added at 02:28 AM ---------- Previous post was at 02:08 AM ----------
msailer said:
Uhhggg, did the replacement on my son's Aria. It wasn't so bad, but now the LCD screen doesn't light.
I get the vibration when you first hit the power button. Is this correct? I'm not too familiar with the phone.
Rececked the connector for the LCD and it seems to be snapped in.
Click to expand...
Click to collapse
same thing is happening with me as well..
^^^^ Soooooo.....I got the same thing on my wife phone, the BLACK SCREEN. I did my homework and read and watched videos on how to replace the digitizer. I was in a steamy room with all my tools from work with pre-cut electrical and .005" double sticky tape. im a mechanical assembler. I did everything to the tee and was very carefull. i think i got a bunk one from china. I bought mine for $19 from china. It had at&t logo and everything. you get what you pay for? So I've got to pay now $50 for a replacement phone through ins. Not bad because before i made the claim i thought the replacement was $150. Anyways just a heads up. Now i got a phone of spare parts Whats cool is that i get to root her phone all over again. So if anyone here has had the black screen. let me know what happened next with your situation. Did you fix it? replaced it with another one? thanks
Hey anyone already opened up their HD2? I need to open mine since my back button got stuck while my baby girl tried to press too hard on it. Now the back button feels like it's not presing at all compared to the other buttons.
i also have a spare housing that I am thinking of putting in.
Anyone can point me to the right direction?
Thanks
i've had the back off mine.
first search youtube for leo disassembly and you'll find an htc disassembly video: "leo Ds" (and another "leo As" for reassembly). they are somewhat daunting, but do not despair!
mine came back from a htc warranty service with a fingerprint on the inside of the lens glass and i couldn't be bothered sending it back again for cleaning so i did it myself. cracking the case isn't all that easy, or wasn't for me.
after you remove the 4 screws (get the void sticker and moisture indicator out with a pin), you still have to unclip the back from the chassis. WHY do electronics manufacturers design them like that??! in the video the tech uses a plastic hooked tool which i do not possess so i had to rely on my fingernails -- which i nearly pulled out! i tried for a good 15 minutes before it finally separated (with me sweating all the way that i was going to damage the LCD with the force i was having to apply). but it all finished happily in the end.
good luck with yours!
Not sure if it's worth it.
1st things 1st, watch the video on youtube..
.
Assuming u broke the keypad (just like me, but mine is right in the middle) at about the 6th minute of the disassembly video, they'll show u where u'd be replacing the keypad.
Removing the 'lcm and follow the indicator' isnt as simple as it look. you'd find the glue to be really tough. Putting it in an oven, sure, it'd be hot to the touch, and let it cool down a bit it'd be hard again. Hairdryer? Still too hot. Gloves?u'll lose touch sesitivity. So what i did was use a small blade/box cutter and cut which ever visible glue... and assembling, i had to replace all the double sided tape with some cheap ones...weak ones. Could be a good thing.. or a bad thing. Good, cos i know i dont have to wrestle with some really tough glue..in case i ruined my lcd again.... bad.. cos its..not that secure, i rmember that i nearly ripped it open unintentionally!
Neway replacing my digitizer+lcd took about 3 hours...had a couple of breaks, and spent 15 mins looking for the proximity sensor or was it the ambient light sense 'lense'..very tiny things those things are. So be careful...cos i eventually lost it..grrr
Anyway, Best of luck.. .now to find a replacement keypad that cost less than 5usd..hehe
dsx2b said:
1st things 1st, watch the video on youtube..
spent 15 mins looking for the proximity sensor or was it the ambient light sense 'lense'..very tiny things those things are. So be careful...cos i eventually lost it..grrr5usd..hehe
Click to expand...
Click to collapse
a good tip here is to work with the phone in a large tupperware box so that if something drops out it can't go anywhere.
note to the OP: i've read several posts where people damaged the ribbon cable connecting the bottom buttons to the mainboard so be careful. it looks very delicate.
Having just opened mine up several times recently I can offer a couple of tips.
1. Unscrew the four screws - they are T5 torx size.
2. Use thin stiff plastic pieces (I found the plastic case that nails are sold in to be the right stiffness and thickness). Cut some up and push them between the case and the phone works so that they hold each of the locking tabs out in turn. I used five or six bits to do this. Three on the vol control side, two at the top and one on the top area of the other side.
3. Then pushing out at the top where the battery would sit while prying with finger nails outward on the long vol control side you can work each of the locking tabs out so the plastic bits hold them unlocked. Do this along that side, across the top and down the other side working each one a little bit as you go and repeat.
4. This should allow the top edge to come out allowing you to lift is out and "up" so that the button end slides out.
This worked very well for me..several times.
The display is held to the electronics portion by double sided tape and yes it is very strong. But you can soften the adhesion significantly using a heat gun. But you must be careful to heat the whole area to avoid thermal differences cracking the screen. The heat will loosen the tapes grip allowing you to pry the screen away from the electronics side.
Note that the screen is made up of the LCD covered by the glued on digitizer and they are connected with a single ribbon cable on the lower right hand side (I think from memory). This means the screen has to lift off with a hinge action. Lifting along the opposite long edge to the ribbon cable, rather than lift from the top or bottom.
Hope this helps.
Hi, I tried to open mine and followeed the video, be careful as the video makes it look much easier than what it really is, I ended up ruining my device, just take your time and do it slowly.
Thanks guys! Gonna try it over the weekend. Worst case is that I break my case or put some cosmetic damage. I have a spare case though hehe.
The problem about the key is the back button feels stuck.... the other buttons are snappy and have a tactile sort of feel, where as the back button doesn't have the same feel. looks like it was pressed to hard and never popped back up...
just annoying when i've been very careful with the phone.
ok looks like i wouldn't have to open my phone.... i tried to but then there's a warranty void sticker, so I just called tmobile and explained about the back key being stuck.... and they're sending me a replacement.
i'm gonna lose my invisible shield full body though... but better than risking breaking my phone....
Okay, I read that someone lifted part off the front by removing a screen saver! Now with me, I recognized that on the left side bottom, left to where the slideview and call buttons are under, the ENTIRE part seems to come up.
It is lifting itself and I bet in a few days/weeks this will get off.
So my question is if anybody had this happen and knows what is under there? Is there a possibility to GLUE it back on?
Now since I am watching this, I think the ENTIRE front can come off eventually and if it is just glued on at the bottom where one has to press the buttons all the time, it is only a matter of (short!) time until this gets out of hand.
Anybody found anything about taking this phone apart yet?
That happens to my phone, I do not bring it back because I buy it in a duty free shop here it japan and also that is the only issues on my phone and only some bugs. I just press it always there to bring it down but it keeps popping up. I think i can glue it, so I do it to fix the problem. Just be carefull if you do it, I notice that under the plastic screen there are buttons (as I think it is) the hard part that you feel when pressing the slideview or call. When you use a liquid glue and put to much, it can go to that button and worst may stuck that part or go inside the phone and also the part where the mic is. I put glue just on the sides just make sure to put small amount at a time. I cannot give the brand of the glue that I use because its in japanese.Now only the small part in the call buttons is up a little because I cannot put enough glue on that part, but in the slide view button its now okay and working well.
This is my firts post on xda hope it helps a little.
So I've browsed around and there are plenty of screen issues, but I haven't seen the one I'm experiencing nor have I seen a solution. When I press the power button my screen comes on and turns off right away. Sometimes a few seconds after I hit the power button sometimes even longer. Most times I won't even be able to put in my security pin to unlock the phone. I see people saying Verizon will do an update soon but that isn't good enough considering I can't use the phone. I did find a loop hole to this problem. Quick start the camera with the volume down button then press the home button after the camera loads and it won't shut off by itself. I thought I'd post this method up for others having this frustration.
If this particular problem has been discussed and beaten to death then the mods can close the thread.
I've got a YouTube link but I don't have 10 posts to show you. Search for user name "vfreeza" and it is the only video I've uploaded. You'll see my first time turning the screen on was using the quick camera method and the times after is with just the power button. The screen turns off without even my hand touching the phone.
don't cover the sensor on the upper left hand side
Yup I read that too. My fingers rest at the corners of the phone and I've tried the not cover sensor thing as well, makes no difference.
Wish I could disable the sensor. I hate this problem
Sent from my LG-D802
Just a quick update. I bought a Diztronic tpu case and the moment I put it on all the problems went away. Screen acted nornal and knock works. My guess is without the case my hand is making some kind of connection it shouldn't be when I'm holding it without a case.
wholemilk said:
Just a quick update. I bought a Diztronic tpu case and the moment I put it on all the problems went away. Screen acted nornal and knock works. My guess is without the case my hand is making some kind of connection it shouldn't be when I'm holding it without a case.
Click to expand...
Click to collapse
Did your old case hug the bezels tight? because it tends to mess with the digitizer perhaps the incipio feather case? or a plastic case of some sort? just curious im pretty sure that was your problem cause if you barely press on the screen youll notice waves in the lcd screen and since the bezels are so small on this device some cases can do that.
Cyko.Tech67 said:
Did your old case hug the bezels tight? because it tends to mess with the digitizer perhaps the incipio feather case? or a plastic case of some sort? just curious im pretty sure that was your problem cause if you barely press on the screen youll notice waves in the lcd screen and since the bezels are so small on this device some cases can do that.
Click to expand...
Click to collapse
The phone was naked, no case at all.
wholemilk said:
The phone was naked, no case at all.
Click to expand...
Click to collapse
thats extremely odd but im glad you got it fixed!
Thanks! This case is never coming off! haha
My phone has that very problem and it's driving me insane.. i love this phone, but it truly is a hassel to use it after its been idle for awhile.. or at night... hands no where near the sensor or anything, it could be laying straight up or down n itll still have that problem.. thanks for reading.
I normally just wipe the sensor area, n it magically starts working again.. n i don't touch it, n the problem comes back after awhile....
Also naked phone besides screen protector, but it's not covering up the sensor.
My phone does the same thing. It's so ****ing annoying.