After i hang up on a call (when the phone is in sleep mode and the screen is locked) the screen unlocks. this is quite contrary to what is mentioned in the phone manual chapter 1 page 45. this becomes an issue since i use a bluetooth headset and the phone remains in its sleeve/case and after every call, a whole bunch of applications will launch since the case is in contact with the screen. have i overlooked some settings or are there other owners who have faced this issue?
ideas and suggestions welcomed
did you check it out if any of the hardware buttons being pressed against the case hence wakening up the phone.?
i had it to only closed al my apps in taskm and it stoped flickering
My HD2 is also behaving in the same way even in controlled test conditions - the phone unlocks when a call comes in (I'm presented with slide to accept or reject call) The phone unlocks during the call, but fails to lock again on disconnect (either by pressing "end call" or hang up via bluetooth).
Can anyone verify this? Is it interacting with something I installed?
I believe I found a (complicated) workaround.
What I want: leave HD2 inside pocket, answer calls with bluetooth headset, hang up and phone will go back to lock.
Problem: After I hang up using bluetooth or press the big red "End Call" button or the other party hangs up, the phone stays unlocked! It stays powered on and all kinds of buttons gets clicked.
Practically all lock sw uses their own lock screen (which I don't want to install). CSDevCtrl does not trigger by phone. TouchLockPro uses its own transparent lock screen but can respond to phone events. Using the !SUSPEND for TAPI\Ended under settings does not seem to work when the screen dims about 50 secs into the call.
Solution: Use TouchLockPro together with LockAndOff. Get TAPI\Ended to run LockAndOff will turn phone off, whether by bluetooth, big red "End Call" button, or the other party hangs up.
BTW: I think there is some confusion on whether the phone locks when you
1. press the big red "End Call" button, or
2. the hard "End call" button
in the forums.
I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.
linivan said:
I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.
Click to expand...
Click to collapse
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)
johncmolyneux said:
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)
Click to expand...
Click to collapse
My proximity sensor does not work, when I am getting a call my screen turn off and when I am taking the phone out from my face it turn on only when I am out side at the sun!! the screen stay off when I am inside room. I tested it with flsh light and it is working also.
I have a T-Mobile US version of the HD2. I am having the same problem when using the bluetooth system in my car. After answering or making a call the phone stay unlocked. And then starts making random calls while I am driving!!!!
There has got to be an easy fix for this!!!
Buy pocketshield, problem solved.
i have this unlock problem with 1.48 rom and i solve it by pressing start button and lock. after that everything works fine unless i change theme in settings. then just repeat first step.
Solved
Same trouble with me until I use the following software. I tried it and it's almost perfect. unzip it and just copy to your HD2, run CallerLoc.exe and click Yes, you'll find:when you hang up, or he/she hang up a call, or a call is established, the screen will turn off.
Why say 'almost perfect', the software is in chinese, but the filename is in english. and it's a call location software but with the function we need.
To stop or before you delete the software, run Callerloc.exe and click Yes again.
Hope this will help you. Sorry I don't find a English version of this software. I esure and I'm using this software perfectlly with my Leo.
theciscokid said:
Buy pocketshield, problem solved.
Click to expand...
Click to collapse
Same for me
Greetings.
I understand this is quite an old thread I'm digging up but I need a little help as well and I didn't want to start a new topic just for that.
I've this silly problem, appeared right out of the blue:
You all know the standard manila behavior, when the phone is idle, the screen first dims and after some more time, depending on your preferences, the screen locks. It also locks if you press the power off button. This all was happening to me till this morning.
I added an event in the calendar (the only change I made today) and after that, my phone dims and then goes in sleep mode after the designated period of time, but DOESN'T lock!!! It doesn't even lock when I press the power off button. I can still lock it by pressing Start and then lock or by press and hold the power button and choose the lock phone option. So one would say that it's still operational, so why bother about it, but I kinda liked the standard function and I have to freaking idea why it changed!!!
I'd be most appreciative if you could offer some help with that.
Oh, I forgot to mention. Soft reset didn't solve the problem. Erasing the calendar event didn't either.
My phone runs the factory ROM (1.66.482.1 ELL), I haven't changed anything other than user settings (yeah, I'm a noob... )
Thanks in advance!
Nasos
Pocketshield could be the end of your problems. You can try it for 10 days and see how it goes...
But why do I need to buy third party software in order to revert my phone to it's original operation?
No, this is not the answer I am looking for. I was wondering if you know of any kind of settings that might have changed by accident and caused this undesired behavior.
Thanks.
The best to return to normal operation would be a hard reset. Or you can spend a while trying.
You can try
HKLM\Software\Microsoft\Shell\Lockscreen\Enable=1
HKLM\Software\Microsoft\Shell\Lockscreen\Active=1
Thank you very much. I opted for the hard reset option... I hope it stays ok this time!
My HD2 also had some strange unlocking and unwanted calling.
I noticed it appeared when using the android style lockscreen.
When I changed back to the original one, problem solved
i had this too. the andriod lockscreen seems to be a bit buggy last time i used it, i accidentially called 7 random numbers
Any tips or tricks on how to lock the phone while using the phone, since it has no top lock button
thanx in advance
godman_8 said:
Any tips or tricks on how to lock the phone while using the phone, since it has no top lock button
thanx in advance
Click to expand...
Click to collapse
if you are using the phone the proximity sensor will turn off the screen once it touches your face to prevent screen buttons from being pressed.
for some reason I turn turn off the Phone Connection (pretty much like airplane mode) while in the phone and it happens a lot, and it bothers, so I was wondering how to lock it to bypass this issue
You gotta make sure that you are on the dialer when you put it upto your face, anywhere else and the proximity sensor won't do anything. I have a terrible habit of hitting home, then opening a dozen programs while talking to someone cause my screens hittin my ear. Just make sure that you are on the call screen before moving it to your head and it should do the rest.
sounds good nuff, i'll try to keep that in habit, so used to android devices with a lock button lol, thanks guys
I just hit the notification bar an then hit lock at the bottom of the screen while talking on the phone, now I use Inesoft phone.
Every time I turn the screen off, the phone vibrates 2 times with about 5 seconds delay. I have tracked this vibration down to fingerprint scanner. Its seems to be an indication of it going to sleep. When you turn the screen off, you can place your finger on the scanner and it will wake the screen up. This function is active for few seconds, and then the scanner goes to sleep (signalized by the vibration).
Anyone know how to turn this notification off? Or even better, how to disable this whole function entirely so the scanner sleeps immediately after screen goes off?
Additional information
the Vibration occurs even if you turn the screen on after turning it off but before the vibration (seems irregular though)
the time of the vibration changes with the lock time setting
turning off notification vibrations entirely helps, but I dont want to do that
not using the fingerprint unlock helps too, but I would prefer to keep using it
KowboyBebop said:
Every time I turn the screen off, the phone vibrates 2 times with about 5 seconds delay. I have tracked this vibration down to fingerprint scanner. Its seems to be an indication of it going to sleep. When you turn the screen off, you can place your finger on the scanner and it will wake the screen up. This function is active for few seconds, and then the scanner goes to sleep (signalized by the vibration).
Anyone know how to turn this notification off? Or even better, how to disable this whole function entirely so the scanner sleeps immediately after screen goes off?
Additional information
the Vibration occurs even if you turn the screen on after turning it off but before the vibration (seems irregular though)
the time of the vibration changes with the lock time setting
turning off notification vibrations entirely helps, but I dont want to do that
not using the fingerprint unlock helps too, but I would prefer to keep using it
Click to expand...
Click to collapse
Hey. My g928c is runnin on custom rom/kernel. Not sure that could be the same or not but when I turn off the screen, it doesnt wake without pressing home or power button. Maybe you use easyHome app or kind of app which uses fingerprint sensor. My device doesnt wake up after turned the screen off and placing a finger on the scanner or etc. As I remember, easyHome app has got that wake up option but in one of older versions. I hope you solve it..
Oh, I was sure this behavior was caused by the sensor, but now that I actually switched back default locker, it doesnt do it. So the issue is entirely in the Hi Locker I am using. I should have checked that in the first place. So thank you. Now my question changes. Are there any more locker options that use fingerprint scanners other than the default and hi locker?
KowboyBebop said:
Oh, I was sure this behavior was caused by the sensor, but now that I actually switched back default locker, it doesnt do it. So the issue is entirely in the Hi Locker I am using. I should have checked that in the first place. So thank you. Now my question changes. Are there any more locker options that use fingerprint scanners other than the default and hi locker?
Click to expand...
Click to collapse
Glad to know you solved it. Im using default lockscreen and never wondered any others lol. Maybe you try{if didnt} Go launcher's go locker etc. Dont know anything more in this case sorry, good luck.
I tried few other alternatives and honestly they were way too cumbersome and bloated. For now I revoked Hi Locker's permission to make notifications, which got rid of the vibration. I hope nothing broke with this modification. Thanks for getting me on track.
When I go to unlock the phone with fingerprint i need to physically press down, I thought it may be ROM issue but I went back to stock and still a problem, has anyone else had this happen, it works so it's not dead.
I think the press down to turn on screen method is standard. I've always had to do press the fingerprint/home button to turn on the screen, and the fingerprint recognition/unlock happens simultaneously.
dmd3746 said:
When I go to unlock the phone with fingerprint i need to physically press down, I thought it may be ROM issue but I went back to stock and still a problem, has anyone else had this happen, it works so it's not dead.
Click to expand...
Click to collapse
this is standard as long as the screen is tuned off. If screen is on the fingerprint is read without the button being depressed
Yes, the FPS only works when the screen is on. Normal. Cuts down on battery drain by not keeping the FPS live all the time.
Hello folks,
I got my OP5 today, damn is this a sexy phone!
I've set up everything like I want it but there is something annoying I faced..
Every time I lock the screen (aka, turn screen OFF, push power button or via button gesture) the phone vibrates 4 times in a very short pattern.
What is this? Where can I disable it? I can handle a slight vibrate when unlocking, but I don't unterstand it when I lock the phone.
Thanks for your help!
Just googled and found this it's so annoying! It doesn't do it on silent mode only ring and do not disturb.
Oneplus please fix it, and while you are at it turn allow us to turn off the double tap to wake and fingerprint sensor vibration if we so wish. Sick of my phone vibrating when its in my hand because my palm touches the fingerprint sensor.
Are you running Light Flow? If so this is the source of your problems.