The Wi-Fi signal on my I9505 is terribly weak. Sitting at the same desk the router is on - full signal; Walk 3-4 meters away - signal drops to 1 line; Go to a different room - disconnects due to no signal. I can only see 3 networks at 1 signal line while on another phone I get 11 networks - all with signal at 2+ lines.
My router is perfectly fine (works as expected and has great coverage on other phones/laptops - it still gives off great signal if I go next door/above/below me).
Phone software side I'd say is fine too, but I'm not 100% sure:
Issue happens both on latest WizCyan (TW based) and on latest RR (CM14 based), both using different kernels.
Currently on XXUHPG1 bootloader and baseband. PDA version is XXUPPI1 (according to the "Phone INFO" app).
Hardware side, I've tried a few things - bent all of the golden springs I could find just a tiny bit upwards, tried to clean the gray contacts on the mid bezel as best as I could (dry microfiber) - they weren't dirty or anything, but they seem scratched/shiny where the spring would have come into contact, is that bad? (I can take pictures if necessary)
I even flipped the blue antenna wire around (though I think that one only affects cell signal).
I also have to note that there's something wrong with my Wi-Fi IC / mobo because sometimes it stops working altogether (won't turn back on), needing a reboot or physical intervention. I doubt that would affect signal strength, as long as it's actually turning on, I guess?
Edit:
SOLVED!
Well, this is probably a very unique/fringe case - I found out there was a crack in my motherboard, just below one of the antenna connectors. I also found out that pushing down on where the crack is relinks the motherboard connections and gives back the full Wi-Fi signal. So I "ghetto-rigged" a piece of plastic to push down on the crack when I put the mid-bezel back in, and it seems to be working for now. Hope it holds up and doesn't cause other issues.
Actually, it could affect signal strength. You might want to check your antenna wire running down the right side of the battery compartment and make sure it isn't broken or partly disconnected.
You should also note that some phones have better antennas, thus having better reception.
So comparing it to a different phone isn't really a good way to measure the effectiveness.
Took some pics, I've no idea if they're of any help. Maybe somebody can tell if there's something wrong.
Strephon Alkhalikoi said:
Actually, it could affect signal strength. You might want to check your antenna wire running down the right side of the battery compartment and make sure it isn't broken or partly disconnected.
Click to expand...
Click to collapse
That's the wire I had flipped around. I even disconnected it to see if there's a difference, and it only weakened the cell signal. Full cell signal when I put it back. No change regarding Wi-Fi. If I run the phone with the mid bezel off, I only get 2 lines even next to the router, and it doesn't even connect - so I suppose the mid bezel antennas connect?
Pwnycorn said:
You should also note that some phones have better antennas, thus having better reception.
So comparing it to a different phone isn't really a good way to measure the effectiveness.
Click to expand...
Click to collapse
True, still, from full signal to 1/0 lines as soon as I go from my desk (and router) to my bed 5m away isn't right. Wi-Fi reception used to be as good on my S4 as on the other phones. (I can't remember exactly when this started.)
I believe you have a radio chip issue. Something that software cannot fix.
Solved. Thank you for trying to help.
@cLick1338: Telling people you solved the issue without revealing the solution doesn't help anyone who may come across this thread in the future. So how did you solve it?
Strephon Alkhalikoi said:
@cLick1338: Telling people you solved the issue without revealing the solution doesn't help anyone who may come across this thread in the future. So how did you solve it?
Click to expand...
Click to collapse
I had edited the first post. Figured it would be most visible for such people.
cLick1338 said:
I had edited the first post. Figured it would be most visible for such people.
Click to expand...
Click to collapse
If you edited it yesterday I wouldn't have noticed it. The XDA app automatically drills down to the first unread post and I don't always think to scroll back up.
Sorry.
Related
I have problems with my signal at work, it's at the minimum in 1X. I can barely make/receive calls, and they cut out often. While at work I came across this video metacafe.com 963126 boost your cellular signal
It claims that by doing this simple project you can increase your signal. So I decided to try it. Sure enough, it works!
The problem now is that once I took the cable out for comparison of with Vs. without, i have no signal!
So, before I would have ~ 1-2 bars at home, enough to be in EV and get on the net without any problem. Now, I can't get on at all, and I can only get a line on roaming, which was completely disabled before. Also my extended battery which would only be at 50% after fri,sat and sunday's use is now at 27% sunday morning! (last charged friday afternoon).
So now I have modified it so i can keep this antenna inside under the battery cover and i'm getting 2 bars again, sometimes full bars (at home). I would still like to put it as it was before.
But my main question is, WHY did this happen? It's not like something got jammed up in the antenna plug. So, what are your thoughts?)
This thread, over at pdaphonehome, includes several posts warning that the connection to the external antenna connector is somewhat fragile, and if it is damaged it disconnects the internal antenna also.
http://pdaphonehome.com/forums/ppc-6800-xv6800/91095-antenna-port-what-can-used.html
Thanks for the info. I think you're dead on, the connection was damaged. I tried playing with it for a bit, but I just can't do anything. What i've done since then is left the external antenna I made inside the case. It works i'd say as good as before, and sometimes better. Oh well, what a bummer.
At least everyone else can know for sure now!
bakntyme said:
This thread, over at pdaphonehome, includes several posts warning that the connection to the external antenna connector is somewhat fragile, and if it is damaged it disconnects the internal antenna also.
http://pdaphonehome.com/forums/ppc-6800-xv6800/91095-antenna-port-what-can-used.html
Click to expand...
Click to collapse
Looking at the results of the xda-developers pool I decided to get an XPeria as it clearly out shined all other phones. I got X1i this Saturday and was shocked about the poor signal strength. I was so looking forward to using this phone and keeping it but was more inclined in sending it back. Now after a couple of days just browsing the developers site which I am used to as I had an artemis before this. I see this was not the last of the problems. There have been mentions of overheating and GPS lag as well as the WIFI being rubbish. I have found the following problems
1. Signals fluctuating and mostly no service when in hand even in some good reception areas. Normally on H when in the carry case but switches to G as soon as held in hand.
2. GPS is frustrating. My artemis used to lock within seconds while having an upto date ephermis file. But even with AGPS and recently downloaded ephermis file, I had to wait over a minute to move off. It locked and then it lost and then it locked again(This was when it was in my hand). Once locked it was stable. It was on Google maps by the way.
Right for these, I have found a temporary solution and we have to work on it to make it a standard solution for all X1. Apparently the signals definitely fluctuate when you touch the lower metallic part on the back which has SE logo on it . The opinion on the forums here is that it may block the signal. I think otherwise as I have covered that area without touching the panel with my hand and there has been no signal drop but as soon as you have the slightest bit of flesh on that area the signal drops at least two bars. This led me to believe that there is an electric conduction or possibly u earth the antennas as they seem to be touching that panel from inside as it has been pointed out before.
So simple test was to put a cling film on that part and then test so I did and walah!! There was no signal drop and it worked flawlessly. I think it’s the same problem with GPS as well.
Now I couldn’t carry on using my phone half mummified. I had to take the cling film off. This is possibly the solution to everyone’s problem but I need someone to suggest either a plastic cover for that area or some sort of coating which does not conduct electricity. I think that will definitely sort the problem.
I think you've got a faulty X1 there mate..
Can you take it back to a store and compare it against another one?
The signal is weak on this compared to some other devices, (it's not as bad as the vario though), however I've never noticed a drop in signal by holding it, so I suspect somethings awry with the one you've got..
GPS signal is very very good with the later radios, what version have you got?
I get a lock within 2 seconds (8 seconds from hard reset or flashed a new rom), and it's very very accurate when it does lock.
My GPS works very well (better than htc cruise) also with previous radio.
So I think you have a fault X1, like say by fards.
I'm with Fards on this, I don't get issues when holding the phone and GPS is snappy.
crabby
Thanks guys. I know it has been discussed a million times before but I have compared the phone with other XPerias and it is the same. There are atleast 4 threads pointing out the same. My X1 would have better signals than my artemis as long as i dont touch the back base. Have you all got silver X1is? If so then can you check if you touch the back panel which i mentioned, if there is any fluctuation in the signals(its not instant it takes about 10 seconds for the phone to show the loss of signals).
I have updated radio to 55 and tried the two new stock roms which are R2A for O2 and 010 generic. The phone still looses signals but not completely when i touch the back panel.
About GPS, it does get a lock very quickly but looses it for a short while when i touch the back.
Anyway if someone else comes accross the same problem then please write here as I am sure there is a solution to be found. I was looking at the following
Clear coating
Antistatic spray coating
I must have missed those threads then.
I have a black x1, and definitely don't get any of those issues.
gps is steady and strong.. monitoring it now... as I type. 6 birds locked standing next to window in house hdop 0.6m which I think is very very good
gsm signal on 2 bars and steady
I had the same issue just once. And even when X1 was in the Brodit car holder.
In my case the soft reset was sufficient to solve the problem. But I guess that you already did that.
fards and pelriog? did you experience any fluctuation when touching the panel?
These are the links to threads
Thread1
Thread2
Thread3
Thread4
Same here, touch back panel, hold for 10 secs and signal drops 1 bar. Currently on 3G network, going from 2 bars to 1.
(And yes, my W810i gets a way better signal in low coverage areas. However, usually not a problem, since I hardly encounter Vodafone low coverage areas in The Netherlands).
Tested 5 times. Dutch Vodafone X1i, R2 stock ROM & stock radio.
Ok I did the touch the panel thing and my bars increased by one... hmmm perhaps there is another faulty batch out there as I get great signal (touch wood) and my gps is very responsive and accurate...
Silver X1 here.. Been touching it up for about 15 mins now
It does seem to drop by 1 bar when touched, but also drops if i just put my hand really close to the back without actually touching. hmm..
what concerns me more is how it just drops the whole line randomly and gives an x then has to search again. Lost a good few calls from that..
well here ive got no problem at all with signal.
But GPS does suck even though most people everywhere say X1 GPS is awesome.maybe it is just my zone/country.. could that be possible?
uhm.. of course not, their satellytes afetr all.
I have disassembled my X1 myself and found that under lower part of backside (piece that have SE logo) is an antenna of some kind.
The antenna is a thick circuit that ran on top of another piece of plastic that cover the loud speaker.
The circuit only have 2 contacts to the main PCB.
My guess is that the reception site of either GSM or GPS is on that part.(may be bluetooth or WiFi too, but I think that's not it)
I wonder what SE/HTC engineer is thinking, putting antenna on this part of the phone! (covered with my hand everytime I use it!)
The solution is "use bluetooth headset" and "hold your phone upside down" and you will be fine.
Yeah, mine loses a bar when touching the metal case at the back, I've not lost any calls (that I know of) because of this though.
I had a look under the speaker section myself last week, and can confirm the antenna circuit over the speaker section. Underneath there's also what looks like a tiny external antenna socket... we could mod our experias to have a rubber duck aerial? Who's up for walkie talkie lookalike xperia?
lol @ walkie talki and upside down. I think the designers have done a very poor job as far as the antenna location is concerned.
Tumpin does your phone loose all signals when in your hand?
Taking this seriously as suggested in my first post has anyone tried putting a cling film on or to that matter anything to cover that area and holding the phone. I did it with the cling film and there was no drop in the signal. So i think it is just a matter of us using some kind of invisible coating or cover on that area so there is no static conductivity. Look at post #5
I would appreciate if everyone gives there suggestions as well how to deal with it. For the people who took the phone apart you could have put something on the inner side to block the static discharge.
I returned my xperia for the second time for signal problems. The problems started after it was repaired for the crack in my case. After that the signal was very poor. GPS was not working in 90%. I wait for 15 minutes for signal, but the only thing that happend was heating the battery. Also HSDPA have a weak signal. In most times I only can use GPRS. The first time I returned the phone for this problem nothing changed. And this time I had a new crack in my case, so I hope they send me a new one!
Im using a X1a and I find its GSM/3G reception is really poor, I already upgraded the radio to the latest but its still the same poor poor reception. Specially when Im using the metal case I frequently get drop calls on my device
kanthai said:
I have disassembled my X1 myself and found that under lower part of backside (piece that have SE logo) is an antenna of some kind.
The antenna is a thick circuit that ran on top of another piece of plastic that cover the loud speaker.
The circuit only have 2 contacts to the main PCB.....
Click to expand...
Click to collapse
Just curious! Any chance that you see what for are the two metal plates contacts from the metal cover of the phone? Those near the SE logo. These two and the other two towards the camera are there for... what? The metal cover is used for something as when you rig in the phone and all four contacts are "online" but what for? Thanks!
I have a black X1i and noticed that reception increased when using it with the keyboard opened in horizontal position.
Same here, I tought it was because I open my metal case that is why reception goes up.
stevencyc said:
I have a black X1i and noticed that reception increased when using it with the keyboard opened in horizontal position.
Click to expand...
Click to collapse
I'm being driven nuts by constant data connection. loss on my Leo.
I have a suspicion it's a hardware problem related to the internal antenna, if there is one. So I've been experimenting holding my phone different ways to see if it helps. And I think I've found a position that improves reliability of connection. Unfortunately it's really uncomfortable, and also maybe coincidence.
Phone in landscape orientation, with the USB port on the right. Tilt the phone till it's approx 15 degrees with USB side highest. Hold phone on the lowest side without touching the metal removable back.
This in 2 hours of testing seems to improve things for me. Though I'm happy go be told I'm being stupid.
Sorry, typed from my phone hence hold became bold.
Isn't the antenna in the base of the handset....? This would mean that most people cover this during a phone call.
I get that in weak signal areas. When im in the loo in work i have to avoid covering the antenna as i lose reception. This was the case with my Diamond also. Dont think its a fault just in weak signal areas your hand blocks what little of the signal there is.
I had very weak reception at some areas of my home (where previously my Diamond had been OK) and it kept loosing the signal. I have installed the new fix for SIM contacts which also updates the radio and I have much better reception at home now. Seems to make a considerable improvement to weak signal areas
Hey there guys, i currently have an issue with my recently purchased G2. Whenever i have the keyboard out holding vertically, i noticed my wifi signal started to decrease when i held at a certain position with my left hand. I usually have my left index finger resting on the side of the keyboard (top part of the phone), whenever i am holding it horizontally and i have noticed that the wifi drops considerable when doing so from 3 to 1, indicated by the wifi signal on the phone.
Any of you guys have the same problem? Try covering the top part of the phone or the left side of the phone if its held landscape (the area where t-mobile logo is) and tell me if your wifi strength decreases. Thanks guys!
youtube.com/watch?v=qdj2y9Fx_5o
(sorry won't allow me to post a link since I don't have at least 8 posts!)
Yes I have had issues with wifi whenever I cover the top part of the phone. Either when in landscape mode or hplding it to my head
Sent from my HTC Vision using XDA App
I definitely see this. I don't even bother trying to play Pocket Legends on wifi.
I tried to google where the wifi antenna was, but gave up pretty quick - normally I have good "4g" coverage so I don't keep wifi turned on, even at home.
i dont think this phone even uses antenna's i opened up my phone before and there was nothing that looked like an antenna unless its inside the screen
My signal drops 1 bar by doing that as well. I assume its where the receiver is located
Sent from my SilverBullet "RootedHTCDesireZ"
Easy on the death grip! also get a stronger wifi router, pref an N router. it'll help you.
it's not even that i have my whole hand plastered on the side of the phone, it is just my index finger that is giving me only 1 bar of wifi, even if it is lightly rested..
I kind of noticed this too last night. I was laying on my bed, and replying to a post in a local forum. I typed in my reply using the HW keyboard, then submitted. Then it failed. I noticed that I was not connected via WiFi anymore. I closed the keyboard and changed switched to a different position, then poof, WiFi came back on.
However, I don't completely blame HTC for this, since my Router's signal (WiFi-N too) is not that strong up in up in my bedroom. So I guess the antenna is located somewhere near there, and when signal is not that good, it drops. Not that big of an issue for me though.
Uh... keyboard out and holding it vertically.... why would you ever hold it like this?
I'm guessing he means horizontally. I get the wifi signal to drop when I hold it like this. There is a hole on same cases near the bottom left (when held normally keyboard out) that gets covered by my hand. This seems to be the location of the wifi antenna.
Sorry i mean horizontally haha. I guess this is a common problem not a unit problem. Is there any fix for this? I use wifi whenever im home or work since it is faster but i find myself clicking links and going to web pages without my left hand placed on the phone (held horizontally) in order for the page to load up fast.
I'd understand if i was covering it fully or if my fingers were firmly pressed against it but this thing is just too damn sensitive!!
Finland_2_Cupertino said:
Easy on the death grip! also get a stronger wifi router, pref an N router. it'll help you.
Click to expand...
Click to collapse
Easy? The man can't hold his phone the way it was intended?
While this is an amazing phone, I'm regretting to learn that the radio equipment is pretty ****ty. It's such a disappointment. I have a top of the line router and live near a cell tower and still get poor reception. All my electronics are RF shielded and I live in a new home with little wireless noise. I know a thing or two about troubleshooting wireless challenges and I am absolutely positive that it's the radio hardware.
I've had friends bring over their devices, one being a DZ and it also performed poorly. Hoping that there's something software related that can be updated by HTC to fix this. Chances are slim though... thankfully I switch out phones every 4-6 months. Love my DZ other than this major flaw.
When I hold my DZ horizontally with keyboard open I either have all wifi bars or 1 less sometimes but it still works very well.
I had indeed to have a look at the icon when I read this thread to notice that I could lose 1 bar sometmes as I have never noticed any problem with wifi.
I have tried different ways of holding the phone and even when I try to cover wifi antenna location I don't always succeed in getting less bars.
Could it have to do with the fact that I'm a girl and have smaller hands so cover a smaller surface of the device?
I've posted a video on the problem.
I'm quite surprised that there is no other thread on this after realizing the number of people that have the same problem. I want to know if this is a problem for all users or only for certain defective G2s, so I know if should send it in.
missparker76 said:
When I hold my DZ horizontally with keyboard open I either have all wifi bars or 1 less sometimes but it still works very well.
I had indeed to have a look at the icon when I read this thread to notice that I could lose 1 bar sometmes as I have never noticed any problem with wifi.
I have tried different ways of holding the phone and even when I try to cover wifi antenna location I don't always succeed in getting less bars.
Could it have to do with the fact that I'm a girl and have smaller hands so cover a smaller surface of the device?
Click to expand...
Click to collapse
That could probably be the cause.
I was able to replicate the issue again, but now with better WiFi coverage. So yeah, I noticed that my signal bars drop 1 to 2 bars when using the HW keyboard, and it immediately pops back up to full strength when held in a portrait position. However, the AP that I was connected to was a G one, I think.
As for me, this isn't quite of a major issue for me yet. I only use the HW keyboard when doing SMS and typing in long info while browsing. Though it can be a pain when doing instant messaging on the phone.
I don't think the type of router is the cause, i think its just poorly placed and sensitivity of the wifi antenna. I tested it out on my university wifi and same result. The engineers failed on this one!
I noticed a drop of radio signal when using the hardware keyboard of my G1 (HTC Dream). IMHO there is nothing like a perfect place for a radio or an antenna in a smartphone. See the discussion going on regarding the signal drop of the iPhone 4, same thing. Every human being has different hands and holds a phone in another way, maybe similar but still different. There is no standardized hand, you know?
Just my opinion. :]
I purchased a Netgear WNDR3700 and set it up using both stock firmware and DDWRT customer firmware and did extensive testing, not just for G2/Desire Z testing but for my other wireless devices as well. I can assure you that the radio hardware and antenna placement/design are really lacking.
I've found that with my new wireless connection there is far more stability as I've never optimized my old router (Linksys WRT610 with DDWRT FW), but a definite loss in signal from the way the device is held. It really sucks, but it's not at bad as the mobile connection. I always have just a couple bars and then 0 bars, then it begins bandswitching and sucking some hardcore ****.
I really love the Desire Z otherwise but it looks like I need to hold out for the Motorola Atrix or the dual core LG Optimus coming out soon.
Me too
I see this drop in reception too, and sometimes a drop in 3G reception when I hold it certain ways. A bummer, but pretty much par for the course. I've never met a phone that doesn't suffer this same problem one way or another.
I just live with it. It's still a great device.
has anyone opened a bug ticket on HTC's site?
A couple of weeks ago, I noticed that where I usually get full or almost full wifi reception, it is at one bar, or it can't even find my network. I have tried rebooting my router and my modem, and even completely restoring my tablet to a different rom. I did drop it awhile ago, but it wasn't that bad of a drop. Can anyone help with my problem?
Thanks
did you search at all before posting?
http://forum.xda-developers.com/showthread.php?t=2096552&highlight=wifi+antenna+fix
PS there was another post recently where OP reported that the bad contact between the antenna contacts and the external antenna was simply caused by the back case being slightly lifted on one corner.
If you tweak the antenna contacts, be careful! If you break one of them accidentally you'll be screwed.
I guess there is no way if I am not comfortable soldering?
Bilge656 said:
I guess there is no way if I am not comfortable soldering?
Click to expand...
Click to collapse
Not true - the fellow in that post was forced to solder only because he accidentally broke off one of the contact tabs. (Should I be inferring from what you wrote you discovered a broken contact?)
The basic issue is (sometimes**) that the antenna is mounted on the removable back cover, and makes contact through a pair of contacts with a slight spring-loading pressure. If the case is lifted/loose, or the contacts are misaligned, or the contact pressure is too low the N7 can behave as if the external antenna was not even connected. You just need to carefully pop off the back case and visually inspect to see if you have an alignment problem or bent/broken contact problem.
That would show up as acceptable signal strength right on top of the router, but then falling off too quickly - e.g. 10 feet away and the signal is less than -80 dBm.
Also, weak/too light contact pressure might introduce an intermittent signal strength - that can cause the software to drop & reconnect.
You should be able to tell which by observing with an app like farproc's "WiFi Analyzer"
good luck
** sometimes meaning that there are other failure modes possible, including a damaged radio front-end on the SoC. It is your responsibility to:
- imagine a failure hypothesis
- create a test scenario which evaluates that hypothesis.
bftb0 said:
Not true - the fellow in that post was forced to solder only because he accidentally broke off one of the contact tabs. (Should I be inferring from what you wrote you discovered a broken contact?)
The basic issue is (sometimes**) that the antenna is mounted on the removable back cover, and makes contact through a pair of contacts with a slight spring-loading pressure. If the case is lifted/loose, or the contacts are misaligned, or the contact pressure is too low the N7 can behave as if the external antenna was not even connected. You just need to carefully pop off the back case and visually inspect to see if you have an alignment problem or bent/broken contact problem.
That would show up as acceptable signal strength right on top of the router, but then falling off too quickly - e.g. 10 feet away and the signal is less than -80 dBm.
Also, weak/too light contact pressure might introduce an intermittent signal strength - that can cause the software to drop & reconnect.
You should be able to tell which by observing with an app like farproc's "WiFi Analyzer"
good luck
** sometimes meaning that there are other failure modes possible, including a damaged radio front-end on the SoC. It is your responsibility to:
- imagine a failure hypothesis
- create a test scenario which evaluates that hypothesis.
Click to expand...
Click to collapse
If there is a problem, what do I do?
Bilge656 said:
If there is a problem, what do I do?
Click to expand...
Click to collapse
I think you need to start having a look to try to identify what the problem is. If you are not comfortable doing any of these sorts of things, you are probably in the wrong place (XDA) and should just return your tablet under RMA for repair. But it is possible that it is something as simple as popping off the back cover and then popping it back in place.