EDIT: I FINALLY HAVE FIXED IT, THANKS!
Hi, I just have recibed a Yotaphone 2 from CooliCool today. I started it and i have been "playing" with it for 10-15 minutes, I have only downloaded Whatsapp and signed up in the google services. Then, I have tried to actualise it to android 5.0. with the official yota flasher but my PC doesn't recognise the yotaphone, so I looked for the drivers on the internet. I have disconnected it and when I looked up to the phone, the e-ink display were locked but it dosn't respond to the gestures, and the phone do not respond. I have tried to start it with up vol button+power button and nothing happens. Do anybody know what can it happens to the phone?
Thanks.
Maybe a stupid question but is your phone charged? If it is try holding volume down and power for around a minute, most of the time this will get the phone in download mode.
Related
Hello everyone,
I have an S3 neo, it's 6 months old. About 2 months ago i started checking in this forums, and then i flashed cm12, and started adding custom roms to my phone. Everything was well, phone was working fine, and so on.
One morning i woke up and my phone went off, and when i turn it on, it's black screen. I restarted few times, took out memory card, and poof it worked. Was all good.
I left it like that and next morning it happened again. And since then i tried all the ways, like take out battery, hold power button 1 min then try to turn it on after few minutes, and so on. Nothing worked. Pulling out memmory card or sim card didn't work either. It's like this for almost 2 weeks i can't use the phone.
I cant get in download mode or custom recovery i i don't know why it won't react on that. It turns on each time like normally, led notifiaction works, the lights on home and back button works, only screen is black. I can unlock it, and such things but cant see anything.
I even succesfully did a factory reset over play store from pc, but that didn't help either..
Biggest problem is that its under warranty but since custom rom i can't take it to service unless i have money to pay... which i dont
I have NEVER DROPPED it, it was never in water, and so on. Doesn't have a scratch at all.
It even has sound, and everything. Just freaking black screen ....
So what i am asking is if anyone here knows how to remove custom rom and custom recovery over pc,is it possible, without the screen? Any way to do it so i can get warranty back ? All i need is a freaking stock rom and stock recovery and a binary reset i guess. Just freaking would need screen to work for 5 mins eh....
If anyone has any ideas please post them, thanks..
Crazeh said:
Hello everyone,
I have an S3 neo, it's 6 months old. About 2 months ago i started checking in this forums, and then i flashed cm12, and started adding custom roms to my phone. Everything was well, phone was working fine, and so on.
One morning i woke up and my phone went off, and when i turn it on, it's black screen. I restarted few times, took out memory card, and poof it worked. Was all good.
I left it like that and next morning it happened again. And since then i tried all the ways, like take out battery, hold power button 1 min then try to turn it on after few minutes, and so on. Nothing worked. Pulling out memmory card or sim card didn't work either. It's like this for almost 2 weeks i can't use the phone.
I cant get in download mode or custom recovery i i don't know why it won't react on that. It turns on each time like normally, led notifiaction works, the lights on home and back button works, only screen is black. I can unlock it, and such things but cant see anything.
I even succesfully did a factory reset over play store from pc, but that didn't help either..
Biggest problem is that its under warranty but since custom rom i can't take it to service unless i have money to pay... which i dont
I have NEVER DROPPED it, it was never in water, and so on. Doesn't have a scratch at all.
It even has sound, and everything. Just freaking black screen ....
So what i am asking is if anyone here knows how to remove custom rom and custom recovery over pc,is it possible, without the screen? Any way to do it so i can get warranty back ? All i need is a freaking stock rom and stock recovery and a binary reset i guess. Just freaking would need screen to work for 5 mins eh....
If anyone has any ideas please post them, thanks..
Click to expand...
Click to collapse
I think you can boot to download mode or revovery. The LED notifi and backlight buttons won't turn on if you boot to download mode or recovery.
Just try to boot to...
1. download mode. Just press and hold for 2-3 seconds power + home + volume down
2. then wait 3 seconds. After that press volume up.
3. Connect your phone to pc, open odin and check if a device is connected.
4. If a device was found by odin - flash a ROM (stock or something else) and hope that this will fix the black screen problem.
Good luck!!
Hi, thanks for ur reply but... My phone turns on when i click home + volume down + power button. I hear sound, blue led notification and so on.......
But when turned on, when i connect to usb odin recognizes it, says connected, and when i try to install the rom i it takes really long and on the end i get fail..*attached the screenshot of fail) I guess because its not in download mode. Any other suggestions how i could get in download mode more?
More suggestions please?thanks
Anyone has any ideas ?
So what all i tried is
Remove battery, hold power button for 1-2 mins, let phone for few mins and turn it on. didn't work
I tried with adb,but usb debugging not on so cmd cant find my device
Only thing left i guess if someone has idea how to get in download mode in some other way or some program that doesnt reguire download mode but can flash rom and etc.
@Crazeh
Take it back to the nearest service center and act the dumb ("I don't know what is wrong with it")
I have done that many times
They are prob gonna call me and tell me to pay for fix
No one has any idea what else should i try ?
try link2sd app form play store. it has the option to boot to download mode. I think titanium backup has the feature also.
My screen is black so i can't do anything on it.....
try to disable ambient screen. report if problem persist
How should i disable ambient screen ? While i can't see anything on phone cause of black screen ?thanks for reply Rox
Anyone?
Crazeh said:
Anyone?
Click to expand...
Click to collapse
ok so i think your problem isn't due to any rom but hardware problem
power off your phone remove the back , look on the left you see a little trap , open it , now you see connector it is the one of the screen try to see if you can disconnect and reconnect it
power on your phone and see if it work :fingers-crossed:
Where is that little trap?
btw if i do this will i loose my warranty completely ?
Crazeh said:
Hi, thanks for ur reply but... My phone turns on when i click home + volume down + power button. I hear sound, blue led notification and so on.......
But when turned on, when i connect to usb odin recognizes it, says connected, and when i try to install the rom i it takes really long and on the end i get fail..*attached the screenshot of fail) I guess because its not in download mode. Any other suggestions how i could get in download mode more?
More suggestions please?thanks
Click to expand...
Click to collapse
If Odin recognizes it, it means it's in Download mode. The device has different interaction with the host over USB when it's not in Download mode.
I don't see the screenshot of the failure. It may be that something got broken in your hardware, so the flashing fails. There's a known issue with the S3 called "Sudden death syndrome", I don't know if it applies also to the S3 Neo, where some of the memory of the ROM fails suddenly. If that is the case (I'm not saying it is, but it might be), there's no fix other than replacing the hardware.
Odin doesnt go over setup connection. cant post screenshot bc im new to the site. btw im sure the phone is on but recognized in odin...
Hello. I was using windows 10 on my phone since it was released as insider preview. Today I decided to go back to 8.1 via the microsoft official tool and then update again to 10, because of the new updates that I wasn't able to get by the normal way. I have done this before, totally works. I connected the phone into the PC via the USB and the software started to download the package, then started installing. In the middle of the installation, the connection between the PC and the phone broke.(Later on I discovered that the USB didn't work properly....) and yeah, after that the only thing that was on the phone was a RED screen(I see this for the first time and yet I have done this before) with Nokia text on it and a progress bar. I tried to turn off the phone, but it didn't work. Couple of minutes ago the phone turned down itself and that was it. Since then, I can't turn it on. I tried holding the volume down button + power button - nothing, I tried with holding the volume down button + power button + camera button - still nothing. When I try to connect it to my PC(with working USB lol) it only says that the device is not recognized....
So, is there any way I can fix this without returning it to the store? I still can't figure out why the screen was RED and why an installation failure didn't just sent me back to the version I was on, instead of doing this... Any suggestions?
Hi guys,
I have a problem with my LG. Yesterday i was casually lurkin some internet or whatever. Havent done anything suspicious or something. Then i switched phone off and put it for a while on the side. When I tried to unlock it after that it was impossible. Phone just doesnt respond. I havent rooted it or done anything connected with roms etc, not into this stuff really. When i plug it into charger red LED starts blinking, then LG logo appears, then battery icon and after that its just charging like normally and still red LED lights. Right now its fully charged so instead of red, the LED is green. The buttons combinations dont work neither (hold power,hold power and vol-) besides holding vol+ and power. I have to hold it for a while, then plug into charger and then some kinda download menu appears, but it does nothing too. Still cant start the phone. However few hours ago i just tried holding power for a bit and everything worked perfectly. Then i locked the screen and *bam* bricked again. I know there are many topics like that but i havent found the exact same problem with solution yet. Every help would be highly appreciated. :good::good:
BUMP please any advice. It actually Turner on one more time, but when i tried using power button, at first it didnt respond, then after few seconds it went bricked back. I managed to take off the backcover so maybe there is sth i can do?
I could be wrong but sounds more software related then hardware to me, maybe try to use one of that flash tools or pc suite to do a clean flash and sadly lose all your data.
If that doesn't help idk....
You don't have a backup do you?
No, unfortunately i dont. I didnt expect that to happen.
Yo so I actually managed to turn it on (i ve no idea how) and its working fine. Im scared to press the power button so it will be unlocked all the time. Ive already done the general backup of photos, music etc, but if there is some good app to make solid backup or something please let me know.
Soo is there any other option to find out if it is finally repaired than pressing power button? I can access data on PC so maybe theres the way to fix it now? If i press the button probably it will brick again, and then after couple of days it will suddenly start working, so id rather dont do this..
Ok, here's as much info as I can give as my phone is locked up:
Stock Mi A1 with 1st Oreo update: December patch level
I have not tried to load anything custom on it, nor have I even loaded the apps to do so.
I took my phone out of my pocket and it is locked on on a screen that says Fastboot.
Power button does not work. Long press power button does not work. Power+UP volume button does not work. Power+UP+DOWN volume buttons do not work.
Plugging the phone into the computer via USB port does nothing.
The battery is non-removable, so I can't pull it to reset.
I am at a complete loss as to what happened, why it happened, and how to resolve it. The phone was working fine this morning. I took it out of my pocket to use it and then discovered the issue. I live in Thailand, and there are no local service centers for Xiaomi, so hopefully someone will have an idea of how to fix the issue.
Any help, ideas or suggestions would be MOST appreciated!
Regards,
KB
UPDATE: I tried to restart the phone via the power button while it was plugged into the computer via USB. Holding the power button down for 10 seconds (guesstimate) did force a restart. This was NOT the case when not plugged in. In any event, if anyone has an idea of what happened and why, I would really like to know! I am wondering if there was some sort of long press key combo or something that happened while it was in my pocket.
Sorry for replying to my own post, but I am totally confused by this issue. I did a lot of searching and reading on Fastboot, and they ALL said that to get there, you had to enable Developer Tools on your phone, download a program for your computer, and then connect the phone via USB.
Here's the thing: I have a photo of the screen, so this is not some hallucination!
1) I DID NOT have Developer Tools enabled on the device. (I do now as I enabled it to see if it was already enabled...it wasn't)
2) I DID NOT download and install an ADB program for the computer.
3) I DID NOT (before the issue) connect the phone to the computer via USB.
So my question is how the h*ll did I get into Fastboot?????
This is really concerning as maybe Xiaomi has an issue similar to the root issue One Plus had and I happened to pocket dial the right combo???? In any event, it does not give me a warm fuzzy about what is going on behind the scenes here!
Any thoughts or info appreciated.
--KB
To get phone into fastboot mode you have to hold power off + volume down button. Might have happened in tight pocket.
_mysiak_ said:
To get phone into fastboot mode you have to hold power off + volume down button. Might have happened in tight pocket.
Click to expand...
Click to collapse
Thanks mysiak...in all my reading, nowhere was that mentioned! And yeah, it was in a pocket pressed up against a seat, so could easily have pocket dialed that combo.
Also, it is not easy to find the solution when it is locked there. I THOUGHT I had held the power off button long enough when trying to get out of Fastboot, but maybe missed it by a second or two. My solution was just to hold down the power button until the phone turned off. Whether that is the correct solution, I don't know as I still have not found anything about getting into and out of Fastboot without a computer.
Regards,
--KB
KB_Thailand said:
Thanks mysiak...in all my reading, nowhere was that mentioned! And yeah, it was in a pocket pressed up against a seat, so could easily have pocket dialed that combo.
Also, it is not easy to find the solution when it is locked there. I THOUGHT I had held the power off button long enough when trying to get out of Fastboot, but maybe missed it by a second or two. My solution was just to hold down the power button until the phone turned off. Whether that is the correct solution, I don't know as I still have not found anything about getting into and out of Fastboot without a computer.
Regards,
--KB
Click to expand...
Click to collapse
Power+volume down button is the usual way how to get into fastboot mode. From a PC you can type "adb reboot bootloader", but many prefer just using phone buttons combo (myself including). If you want to get out of fastboot, you either hold power off button until phone vibrates shortly - this works in whatever mode, even if powered on, basically it's "emergency shutdown" as we don't have removable battery. Or if you are connected to a PC, type "fastboot reboot".
Long story short, you did it right
Btw. if you will hold power+volume up combo long enough, you'll end in stock recovery mode with "no command" on the screen. Don't panic, just hold power off button and then start phone normally
I had the same problem and plugged into the computer via USB and holding the power button down for 10 seconds did force a restart. and the phone is OK since then!!! Thank you you saved my time!!!
Thank you.
Picked up my Mi A1 this morning and it had the beautiful FASTBOOT icon on the screen. The phone has been lying on my desk for several weeks without a SIM. When I could not clear the FASTBOOT message I Googled for a solution and this thread was the result. I just wanted to record my grateful thanks. I plugged the phone into a computer USB socket and held the power button until the error message disappeared, as recommended by KB_Thailand..
XDA doing what it aims to do.:good:
It is always nice to find solutions instead of even more questions. Glad that it helped!
After the initial glitches, the A1 has been pretty dang dependable.
I still am using my A1. The A2 and A3 (someone needs to be fired over that monstrosity) left me flat. I am hoping against hope that the A4 will be 'the one', otherwise I am going to have to look for something other than Xiaomi.
Hello,
at the morning i used my phone as usual, some searching on google, whatsapp messages. After that i drive to work and want to check my messages but nothing happened (30 Min Later), phone still didnt woke up, all Combinations for Flashing a ROM or Recovery doesnt work. Computer didnt ring when i try to connect with the PC....
Smartphone was Full Loaded (95%)
What can i do ?
No informations in ODIN, no USB Connection to the Phone
The Phone didnt fall
Stock ROM, No Root
i had this error years ago with my S8, but idk what i had to do that it work again
sorry for my bad english, i hope its understandable, I hope for help ..
Hmm maybe you already tried but let me ask
Did you try pressing power + volume down for 8 seconds?
Or connect it to the pc while pressing the volume down and Bixby button? Also, try different cables.
the last thing would be to check the warranty if your phone still has a warranty.
Also, you may try to keep the phone connected to charge for a few hours and see if anything happens.