Unlocking the bootloader on HTC Desire 626 LTE (a32ul_emea)1. First of all make sure that debugging is enabled by USB (USB Debugging). --- Settings> Developer ---> Debugging via USB, and put the phone away, yet he will not be needed.
2. Download of attachments to this message archive platrom-tools.zip (at the bottom of posts)
3. Next, you will need to register on the site htcdev.(com) without () (unless of course you are not registered there). Click Register and enter your information, and then check your email to confirm your registration.
4. Once you have registered and logged into your account, log in to Developer Center and select Unlock Bootloader, clicking Get Started on the main page.
5. On the next page, in the drop-down list Select Your Device to the right of the page, scroll to the bottom and select the All Other Supported Models and click Begin Unlock Bootloader button, after which you will see a window in which you have to agree to the terms. Click Yes in the first box, and put the two checkboxes next clicking at the end Proceed to Unlock Instructions. Do not close the page after that, it is very important !.
9. Now your device is in fastboot mode (screenshot below). Leave your phone in this mode and connect it to your computer via USB.
10. Go back to the htcdev.com site (which tab you closed) and click Proceed to Step 5.
11. We have already taken care of everything that is required of us in Step 5 (copied the necessary files in the fastboot folder on the C drive), so skip to Step 6, where we will have to run the command line (Command Prompt) On poyavivshesya page. To do this, click Start on the computer and in the search field, type cmd, select cmd.exe in the search results and the run in administrator mode (right click on the icon cmd.exe ---> in Administrator mode).
12. Now we need to specify the path to the fastboot folder we created on drive C. To do this, type the following command cd C: / fastboot and press Enter. All of us in the folder C: / fastboot.
13. Now click Proceed to Step 8 htcdev.com and enter the command line fastboot oem get_identifier_token, press Enter.
14. You will see this same identifier token, which you will need to copy. Why move your mouse cursor to the command prompt window, right-click and select from the popup menu Mark.
15. Now select the copy token, as shown in the picture below. Make sure that you have captured the allocation <<<< Identifier Token Start >>> first and <<<<< Identifier Token End >>>>> at the end. Do not close the command prompt then just turn it!
16. Now htcdev.com, scroll down the page and locate the box My Device Identifier Token, in which the copy that was just copied your token number. Click Submit.
17. After that, you should see a message about the successful sending of the token, and the fact that Your email (provided at registration) sent unblocking key (unlock key) in the form of a file attached to the letter.
18. Open your email and find just received a letter, to him shall be attached Unlock_code.bin file. Download the file to your computer. Then click on the link Click here to continue the bootloader unlocking process, which will redirect you back to the page htcdev.com with the next step in unlocking, namely Step 11.
19. Copy the newly downloaded Unlock_code.bin created earlier in the folder C: / fastboot and then open a command prompt and type the following command there fastboot flash unlocktoken Unlock_code.bin (the last line in the screenshot below). Press Enter.
20. After clicking the command execution in the preceding paragraph, the unlock code will be sent to your HTC One, and at this moment on the screen of your device, you should see a message which we must accept. Select with the sound buttons (up, down) Yes, and press the power button to select.
platrom-tools.zip
where is the platrom-tools.zip file?
bbbvbvnbvnbbnvbb
Related
Hey all, finally got my N1 today and I've been trying to unlock the bootloader for a bit following the instructions at redmondpie
You can follow the step by step guide posted below (on your own risk) to unlock the bootloader on the Google Nexus One phone. We are not to be held responsible if you ended up bricking your phone. The steps are as follows.
Step 1: Download and extract fastboot from here (Windows, Linux and Mac included).
Step 2: Run a command prompt / terminal at the directory you just extracted.
Step 3: Type ‘fastboot-windows oem unlock’ or ‘./fastboot-mac oem unlock’ or ‘./fastboot-linux oem unlock’ (as appropriate).
Step 4: Proceed on your merry bootloader unlocked way.
Our complete coverage on the Google Nexus One phone can be found here.
Click to expand...
Click to collapse
Problem is I get a "fastboot-windows is not recognized as an external or internal command.
I've tried the command while in fastboot mode and while in the bootloader.
Any help is appreciated.
Carlos
Fastboot devices does recognize my N1
you need to start your phone in fastboot mode. turn off your phone, hold trackball button down, power on your phone while still holding trackball down.
also when you open a command prompt type cd followed by the path to the folder where your fastboot file is at (example: cd C:/myfolder/) and press enter. then type the command
I don't have my N1 yet so I haven't tried.
You're sure you are in the proper directory in the command prompt?
also maybe run the command prompt as admin? (right click on the icon run as administrator)
I'm an idiot.
I was supposed to download the zip attached in that thread and run the command prompt from the extracted folder. FYI: you can hold ctl+shift and left click on the folder to open a command prompt.
Well, might as well sticky this so other people don't have the same problem.
I9000 unlock instructions
1. Power on the phone and go to Applications->Settings->About Phone->USB
settings
2. Select Mass Storage
3. Connect the phone to USB cable
4. Swipe down the top notification bar then tap “USB Connected” then select
MOUNT
5. Copy update.zip file to phone mass storage root
6. Power off the phone
7. Press Volume Up+Home+Power on key to start the phone into recovery
mode
8. Go to “apply sdcard:update.zip” using volume keys then select it using
home key
9. Power on the phone then go to Andoid Market and install Terminal
Emulator
10. Run Terminal Emulator
11. Type cat /efs/nv_data.bin >> /sdcard/nv_data.bin into terminal then type
Enter
12. Connect the phone to PC in USB Storage Mode then copy nv_data.bin file
to your pc
13. Open nv_data.bin file with any hex editor (ex. Hex workshop) then go to
address 00181460
14. There are the codes
15. Power on the phone with any unaccepted sim card inside then type in the
first code to unlock the phone
http://www.mediafire.com/?3v6vsqh9qorrwn2
http://www.mediafire.com/?o8djyf4moc9ae44
use thanks button
http://forum.xda-developers.com/showthread.php?t=762384
This is a double post.
And there is no 'thanks' button
Tyxerakias said:
And there is no 'thanks' button
Click to expand...
Click to collapse
Maybe he copy-pasted from a forum that has one?
I am following 100% tutorial but I am unable to unlock my I9000. Look at the screenshot for the error that I encounter.
I have put the update.zip in root of phone memory, root of MicroSD etc but no chance. Do I need to root the phone or what's the problem?
Thanks
Hi,
I have a NSPRO box and read the unlock code, but as I insert it, it doesn't unlock the phone.
As this didn't work, I tried your method, and the code that showes up is the same as read by NSPRO box, and... it still doesn't work.
Attached is the printscreen of the HEX area where the code is. I've noticed it says "18146D" and not "181460" as your indicated. Could this be the reason why the code doesn't work?
Please help...
Hi to all I have a provlem I need help with.While trying to unlock my bootloader using rsd and fastboot.I get as far as the cmd line entries and have problems basically I cant seem to get my command line to use the fastboot command and or any other fastboot command I can find.What seems to happen all the time is that the command line responds with "this is not an internal or external command" or similar.
Any help appreciated Windows 7 64bit all latest drivers installed
scotty7910 said:
Hi to all I have a provlem I need help with.While trying to unlock my bootloader using rsd and fastboot.I get as far as the cmd line entries and have problems basically I cant seem to get my command line to use the fastboot command and or any other fastboot command I can find.What seems to happen all the time is that the command line responds with "this is not an internal or external command" or similar.
Any help appreciated Windows 7 64bit all latest drivers installed
Click to expand...
Click to collapse
are you in the same folder that the FASTBOOT.EXE is in when you run the command???
Make sure your running CMD as administrator. You can tell by the path that shows when cmd is launched. If its a regular user account it will path to something like: c:\users\"your username"\
If your running as admin it will path to something like: c:\windows\system32
Sent from my MB860 using XDA Premium App
Take your fastboot files and images and put them in a folder on the root of your C: drive... I use one named phone
Then you should be able to open your Command line and type
cd c:\phone
That will change you to the Phone directory you made in the root of C: earlier
If you want to make sure you can type DIR and it should list all the files you have in there.
At this time you can start using your fastboot commands and it will recognize them.
beatphreek said:
Take your fastboot files and images and put them in a folder on the root of your C: drive... I use one named phone
Then you should be able to open your Command line and type
cd c:\phone
That will change you to the Phone directory you made in the root of C: earlier
If you want to make sure you can type DIR and it should list all the files you have in there.
At this time you can start using your fastboot commands and it will recognize them.
Click to expand...
Click to collapse
Another handy thing is to open the folder then hold the shift key and then right click. You'll have an "Open command window here" option.
Yep I use that all the time...
used both the suggestions in here and still having trouble,can do the root of c folder,use the dir command see it is all there but the cd C:\fastbootpackage brings the same response again.Can anyone see where I am going wrong?Once the command line changes to fastboot what do I need to command?Phone is still attached (as per the guide I am following?)showing 100% phone needs manually rebooted.
I have all latest drivers on win 7 64bit and I am definetely running cmd as an administrator
Also as the third suggestion suggests if I open the cmd box from the folder what is the exact command to use from there?Is there an alternative to doing this as I am beginning to struggle?
Unlock your Bootloader
1. You need to download and install RDS lite on your PC:http://forum.xda-developers.com/attachment.php?attachmentid=634879&d=1308872277
2. Download and extract IHOP_Bell.rarhttp://api.viglink.com/api/click?format=go&drKey=1359&loc=http%3A%2F%2Fforum.xda-developers.com%2Fshowthread.php%3Ft%3D1136261&v=1&libid=1311795928774&out=http%3A%2F%2Fdiamantephoto.com%2FIHOP_Bell.rar&ref=http%3A%2F%2Fforum.xda-developers.com%2Fforumdisplay.php%3Ff%3D997&title=%5BPUDDING%5D%20International%20House%20of%20Pudding!%20(Unlock%2Froot%20thread)%20Updated%20July%2023%202011%20-%20xda-developers&txt=http%3A%2F%2Fdiamantephoto.com%2FIHOP_Bell.rar
3. Download and extract Fastboot tools http://gititbit.ch/FAST
4. Power down your Motorola Atrix
5. Take out your microSD card and SIM*card*for the flashing process
6. While turning the phone on, hold the Volume Up button until it acknowledges RSD
7. Your device will say “Starting RSD protocol support”
8. Run “RSD Lite” on your computer
9. Press the “. . .” button next to the box labeled “Filename”
10. Load up the SBF file – IHOP_Bell.sbf
11. Plug your device into your computer
12. RSD Lite should recognize your device and say “Model: NS Flash Olympus” and “Connected…”
13. Press the “Start” button
14. Be patient while the phone*reboots. It will take a long time.
15. Open and extract the Fastboot package from above
16. Open a command prompt window
a.On Windows, press Start and type “cmd” then press the enter button
17.Type the following command. Your directory will be the folder where you extracted the Fastboot package.
(Example:* cd C:\Users\Kenneth\Desktop\fastboot-package)
a.cd*your directory here
18. Power down your Atrix device
19. Hold the power button and the downward volume button until you see “Fastboot”
20. Let go of the buttons and press the upward volume button once
21. You will now see “Starting Fastboot protocol support”
22. Plug your device into a USB port in the back slot of your computer
a.Front slots sometimes do not have enough power to stay connected to the device.
23. Type the following command:
a.fastboot oem unlock
24. You will now receive a warning along with a unique device ID
25. Type the following commands using your unique device ID in place of the ####:
a.fastboot oem unlock ####
b.fastboot reboot
26. Wait for your device to reboot. Congratulations! You now have an unlocked bootloader!
This is the guide I have been using, thanks again
scotty7910 said:
"this is not an internal or external command"
Click to expand...
Click to collapse
This msg will only show if you are in different folder than your fastboot. You don't need to run cmd as administrator. The best thing to do is:
copy those 3 files (AdbWinApi.dll, AdbWinUsbApi.dll, fastboot.exe) to your main c:\ (do not put to the folder)
Run cmd and type "cd \" this will move you to c:\
Now type fastboot and press enter - you should see various commands that can be used. (your mobile doesn't need to be connect to your pc to see this)
Now you can continue with unlocking. If you applied ihop.sbf already then startt from step 18.
I'm 99% sure that you were in the wrong folder.
Thanks very much that last post got it.In fact I would say that is the simplest way I have read so far as far as fastbooting goes.Many thanks.I have been having problems installing tenfars cwm so I will be using the rom manager "official cwm,will using the fastboot-w command be a problem for me do you think?
scotty7910 said:
Thanks very much that last post got it.In fact I would say that is the simplest way I have read so far as far as fastbooting goes.Many thanks.I have been having problems installing tenfars cwm so I will be using the rom manager "official cwm,will using the fastboot-w command be a problem for me do you think?
Click to expand...
Click to collapse
Don't use the Rom Manager app. It sucks and doesn't work properly. Do things properly.
With XDA forum members there's no reason to do things half assed. Use your hole ass, dammit.
scotty7910 said:
Thanks very much that last post got it.In fact I would say that is the simplest way I have read so far as far as fastbooting goes.Many thanks.I have been having problems installing tenfars cwm so I will be using the rom manager "official cwm,will using the fastboot-w command be a problem for me do you think?
Click to expand...
Click to collapse
Well if you came that far then try to install tenfar's recovery, download this file :recovery-en-goapk-0630-1029.zip Unzip and move recovery-en-goapk-0630-1029.img to your c:\....Now reboot your phone and enter to fastboot mode. In cmd go to c:\ and type "fastboot flash recovery recovery-en-goapk-0630-1029.img" and then "fastboot reboot" DONE
If you have any problems try to download moto-fastboot (http://forum.xda-developers.com/attachment.php?attachmentid=635584&d=1308928440). It's kind of the same thing as fastboot and to be honest I don't know what's the different between both (I think moto-fastboot is designed for 2.3.4 firmware). Extract zip and move moto-fastboot to c:\ and type the same command but instead of fastboot type moto-fastboot. I hope this make sense.
Also it's recommended to delete "install_recovery.sh" which apparently is in /system/etc/ BUT I never managed to find this file and I just ignored this step.
thanks foka, but I have already tried and tried again unsuccessfully to use tenfars cwm.I can install the recovery and delete the sh file all as normal using fastboot and astro.However for some reason there seems to be no way I can get into cwm having flashed it.when I attempt it I dont see the same menu I could scroll through as before.Then I tried a cwm of tenfars that was supposed to flash through rom manager.Again the flash went fine but could not seem to enter recovery mode.I see you installed aura 1.1 didi you flash a radio afterwards?My signal is comnstantly 1 bar.Could you reccomend a uk radio?
Well Ive flashed at&t radio N_01.77.30p which solved battery draining and 1 bar issue. I'm not sure why you can't use cwm recovery...
Sent from Motorola Atrix
What do you mean you don't see the same menu as before? When you hold volume down, power up phone, fastboot, scroll through the list and none of them say Android Recovery?
THANKS TO JORDAN011 FOR SOME OF THIS INFO. i tried the origional post but got confused with some of the bits esspeciaolly as i didnt find mention of installing Java which was a big stumbling block so i did more tial and error and research and Rooted my Kindle - heres what i did with links: hope it helps (sorry pics didnt come out and niether did the highlighted instructions but short of time and have to popout -- follow it word for word and it will definately work
1. Turn your Kindle Fire on and swipe down the top bar and tap on More+
2. Goto device and turn on the “allow installation of applications” button (ontop of the reset factory defaults)
3. Go back and then goto Security and turn on the “enable ADB” button
4. On your PC Figure out if you have 32 bit or 64 bit windows running and download the correct versions of java and android sdk below:
5. Download and install Java se7u11 the JDK file. From http://www.oracle.com/technetwork/java/javase/downloads/jdk7-downloads-1880260.html. This is needed for the android SDK to work (otherwise ADB wont work). You may have to register and reboot
6. Download android SDK then extract the folder to your desktop and install the (green icon). download from https://developer.android.com/sdk/index.html
7. If you have installed java and the android sdk – you should get the following screen:
8. If SDK manager asks you to install any missing packages (button on bottom right corner) then install them/accept and install
9. Download then extract to desktop and install the Kindle fire ADB Drivers (don’t worry if there’s an error message – Just install Anyway as its an unsigned file. Download from http://forum.xda-developers.com/showthread.php?t=1893838
10. Open up device manager ie start/control panel/hardware and sound/devices and printers/device manager
11. Turn on your kindle and plug it into the PC
12. Your kindle should be recognised in device manager as Andriod composite adb interface.
13. Download Bin4rysroot from here http://uploaded.net/file/0fpyh5c5
14. download Quemu root from here http://forum.xda-developers.com/showthread.php?t=1893838
15. Extract both the above files to your C Drive into two new folders and rename the folders Qemu (for quemuroot contents) and Root (forbin4ryroot contents)
16. THE ROOTING PART NOW!!
17. On the Pc goto Start and type in CMD then right click on the CMD icon at the top of the window and select “Run as Administrator” and hit yes if the User Account Control window pops up and a dos window will appear
18. Copy and past (or type this into the window) cd ..\..\Root then hit enter
19. Copy and past (or type this into the window) runme.bat then hit enter
20. When the screen shows an interface, type 1 then hit enter, A lot of errors will show up but that's fine
21. When your kindle shows a "Restore" screen hit restore my data your kindle will restore and reboot (may take some time be patient!)
22. After it finishes out you should get a command line on the pc saying “press any key to continue” when you do that you will see C:|\Root>
23. Copy and past (or type this into the window) cd ..\Qemu then hit enter
24. Copy and past (or type this into the window) rootqemu.bat then hit enter
25. When you get another interface type 1, then hit enter, press enter twice until it starts the steps.
26. It'll restart your kindle a couple times make sure you don't press enter until it has booted up again whenever it prompts you to (ie wait 3 mins before pressing enter) your Now rooted – you don’t have to press any key on the pc now.
27. If you want proof, you can download Es File explorer and in the apps settings goto root settings grant it Root permissions in the settings by ticking root explorer boxe and clicking yes and grant for both
:good: thank for sharing..wil try root my kindle fire...cheerzz
Thought this was great, could finally get my mum's Kindle rooted and put Play Store on it....... Then found that it says I've reached my download limit and that I need to register and pay...
Back to the drawing board.
patel989 said:
THANKS TO JORDAN011 FOR SOME OF THIS INFO. i tried the origional post but got confused with some of the bits esspeciaolly as i didnt find mention of installing Java which was a big stumbling block so i did more tial and error and research and Rooted my Kindle - heres what i did with links: hope it helps (sorry pics didnt come out and niether did the highlighted instructions but short of time and have to popout -- follow it word for word and it will definately work
1. Turn your Kindle Fire on and swipe down the top bar and tap on More+
2. Goto device and turn on the “allow installation of applications” button (ontop of the reset factory defaults)
3. Go back and then goto Security and turn on the “enable ADB” button
4. On your PC Figure out if you have 32 bit or 64 bit windows running and download the correct versions of java and android sdk below:
5. Download and install Java se7u11 the JDK file. From http://www.oracle.com/technetwork/java/javase/downloads/jdk7-downloads-1880260.html. This is needed for the android SDK to work (otherwise ADB wont work). You may have to register and reboot
6. Download android SDK then extract the folder to your desktop and install the (green icon). download from https://developer.android.com/sdk/index.html
7. If you have installed java and the android sdk – you should get the following screen:
8. If SDK manager asks you to install any missing packages (button on bottom right corner) then install them/accept and install
9. Download then extract to desktop and install the Kindle fire ADB Drivers (don’t worry if there’s an error message – Just install Anyway as its an unsigned file. Download from http://forum.xda-developers.com/showthread.php?t=1893838
10. Open up device manager ie start/control panel/hardware and sound/devices and printers/device manager
11. Turn on your kindle and plug it into the PC
12. Your kindle should be recognised in device manager as Andriod composite adb interface.
13. Download Bin4rysroot from here http://uploaded.net/file/0fpyh5c5
14. download Quemu root from here http://forum.xda-developers.com/showthread.php?t=1893838
15. Extract both the above files to your C Drive into two new folders and rename the folders Qemu (for quemuroot contents) and Root (forbin4ryroot contents)
16. THE ROOTING PART NOW!!
17. On the Pc goto Start and type in CMD then right click on the CMD icon at the top of the window and select “Run as Administrator” and hit yes if the User Account Control window pops up and a dos window will appear
18. Copy and past (or type this into the window) cd ..\..\Root then hit enter
19. Copy and past (or type this into the window) runme.bat then hit enter
20. When the screen shows an interface, type 1 then hit enter, A lot of errors will show up but that's fine
21. When your kindle shows a "Restore" screen hit restore my data your kindle will restore and reboot (may take some time be patient!)
22. After it finishes out you should get a command line on the pc saying “press any key to continue” when you do that you will see C:|\Root>
23. Copy and past (or type this into the window) cd ..\Qemu then hit enter
24. Copy and past (or type this into the window) rootqemu.bat then hit enter
25. When you get another interface type 1, then hit enter, press enter twice until it starts the steps.
26. It'll restart your kindle a couple times make sure you don't press enter until it has booted up again whenever it prompts you to (ie wait 3 mins before pressing enter) your Now rooted – you don’t have to press any key on the pc now.
27. If you want proof, you can download Es File explorer and in the apps settings goto root settings grant it Root permissions in the settings by ticking root explorer boxe and clicking yes and grant for both
Click to expand...
Click to collapse
I get to step #2 in the script
Step 2 - Exploiting...
/system/bin/sh: cannot create /data/local.prop: Permission denied
My kindle is 10.2.6_user_2630020
What else can be done?
Thank you.
snoopdujour said:
I get to step #2 in the script
Step 2 - Exploiting...
/system/bin/sh: cannot create /data/local.prop: Permission denied
My kindle is 10.2.6_user_2630020
What else can be done?
Thank you.
Click to expand...
Click to collapse
This happened to me. And I googled extensively about the problem. Honestly.. the only thing to do is keep running the script.. worked for me after about 20 tries. Sorry I couldn't be of more help.
snoopdujour said:
I get to step #2 in the script
Step 2 - Exploiting...
/system/bin/sh: cannot create /data/local.prop: Permission denied
My kindle is 10.2.6_user_2630020
What else can be done?
Thank you.
Click to expand...
Click to collapse
Nothing. It's normal and doesn't mean anything. Root still works even with the error
--
Sent from my Kindle Fire 2, CM 10.1
Rooting Kindle Fire 10.2.6
I was able to get my Kindle Fire .v2 rooted. I ran through the process again. This time going back to the beginning.
I wasn't able to get it to run, so I refreshed the files, and ran it again. It took 2 attempts to get the first script to run. I thought it didn't run, so I was searching for a reason why. Then I looked up, and the script had finished. Then it took 3 times for the second part of the script to complete.
After getting the the launcher I wanted installed (APEX failed, so did Novo and a few others) AWD worked, but I was unable to get it to be the default launcher. (the kindle launchers 'default' settings were grayed out.
I then went into /system/app and renamed Launcher.apk to Launcher Default.apk and the com.awd.launcher-1.apk to Launcher.apk.
the system didn't respond when I pressed the home key, so I took a chance and rebooted my kindle.
When it rebooted, I was asked which launcher I wanted to use, so I clicked set as default, and clicked on AWD.
All is good now. Thanks
help
i keep getting a runme.bat is not recognized as a internal or external command , operable program or batch file
when i select 1 and hit enter i'm not getting the restore screen on the kindle it just says that it couldnt' push busybox and superuser and then it asks me wich superuser i want too install 1 or 2 and when i select one it just goes back too prompt. any ideas drivers are all good adb good cant figure it out
hey did u ever get help with that
blythefam5 said:
i keep getting a runme.bat is not recognized as a internal or external command , operable program or batch file
Click to expand...
Click to collapse
hey did u ever get help with that
Work for 10.4.6?!?
Does this work on 10.4.6 at all? My kindle is running this software atm
Thanks
Lewiswatson99 said:
Does this work on 10.4.6 at all? My kindle is running this software atm
Thanks
Click to expand...
Click to collapse
Use step 1 http://forum.xda-developers.com/showthread.php?t=2075959
Hello everyone, need help
I've got Amazon Kindle Fire HD, the version is 10.2.6. Want to unlock it. I follow this instructions step by step, then i stumbled on the 18 step.
It says "Copy and past (or type this into the window) cd ..\..\Root then hit enter" I type everything as written and system says that it is not able to find the reqested path..( What should I do? Maybe I should type same exact address instead of ..\.. ? Thank you for your response in advance.:angel:
Vitaliy7 said:
I've got Amazon Kindle Fire HD, the version is 10.2.6. Want to unlock it. I follow this instructions step by step, then i stumbled on the 18 step.
It says "Copy and past (or type this into the window) cd ..\..\Root then hit enter" I type everything as written and system says that it is not able to find the reqested path..( What should I do? Maybe I should type same exact address instead of ..\.. ? Thank you for your response in advance.:angel:
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2075959
Disable the Driver signature enforcement on your PC by following these steps:
Open the Command Promt window by clicking the Start button, clicking All Programs, clicking Accesories, an the right clicking Command Prompt and select "Run as Administrator".
On the Command Prompt type enter the following command:
Code:
bcedit.exe /set nointegritychecks ON
This will disable the Digital Signature
Download Drivers for related tools
Install All Drivers provided and please click any prompt that mentions to Skip obtaining driver software from windows update
UnZip driver package(QUD.WIN.1.1 Installer-10030.1)
Run setup.exe as administrator setup.exe and Click next button step by step to finish.
Make sure device is powered off and battery is inserted
Press and hold the volumen up button. While the volumen up is being held coonect the device to your PC and continue holding the volumen up button until it shows a lightning bolt “flash”
If drivers are installed correctly, you should see a port called WinUsbDevice in the Device Manager (Start > My PC or Computer > Right Click > Manage > Device Manager)
Download and unZip FFUTools folder to the root of your Local Disk (C drive.
UnZip of software that you attemting to flash and inside the zipped software software file should be a file called Flash.FFU
The Flash.FFU file needs to be copied to C:\ffutool
Once the Flash.FFU file is copied to C:\ffutool double click the Flash FFU.bat file to start flashing the device.
A command prompt should be open and begin to flash your device.
Once the device is flashed, the device will power on by itself and you may closet he command prompt.
End.
Links dead please share elsewherr
Enviado desde mi SM-G930F mediante Tapatalk