Hi,
I bought a water damaged P8 Lite for repair/parts that I was able to bring back to life.
However, volume up key is not working, and phone has a password on it.
I tried a different set of buttons but the problem is in the board.
Consequently I can't boot recovery mode and hard reset the phone.. Is there any other solution to solve this and use this board?
Thanks.
Use fastboot to flash a new firmware....this should work
madz78 said:
Hi,
I bought a water damaged P8 Lite for repair/parts that I was able to bring back to life.
However, volume up key is not working, and phone has a password on it.
I tried a different set of buttons but the problem is in the board.
Consequently I can't boot recovery mode and hard reset the phone.. Is there any other solution to solve this and use this board?
Thanks.
Click to expand...
Click to collapse
Well, since you bought water defective P8 Lite, i guess you're having problem on the board (or at least with hardware), and if that's the case then it is better to change the hardware.
But, you can also once try flashing new firmware via fastboot method. Remember flashing requires your bootloader to be unlocked, so make sure it is..
The Process??
Enable Developers Option and USB debugging (assuming that you can switch it on)
Connect your mobile to laptop/computer.
Make sure you have Minimal ADB and Fastboot Installed. Download link: http://forum.xda-developers.com/showthread.php?t=2317790
Commands:
adb devices ---- will show your serial number if its enabled
adb reboot bootloader --- will show your bootloader status (if it's green then you can flash files)
amageek said:
Well, since you bought water defective P8 Lite, i guess you're having problem on the board (or at least with hardware), and if that's the case then it is better to change the hardware.
But, you can also once try flashing new firmware via fastboot method. Remember flashing requires your bootloader to be unlocked, so make sure it is..
The Process??
Enable Developers Option and USB debugging (assuming that you can switch it on)
Connect your mobile to laptop/computer.
Make sure you have Minimal ADB and Fastboot Installed. Download link: http://forum.xda-developers.com/showthread.php?t=2317790
Commands:
adb devices ---- will show your serial number if its enabled
adb reboot bootloader --- will show your bootloader status (if it's green then you can flash files)
Click to expand...
Click to collapse
Hi,
Unfortunately I'm unable enable usb debugging and can't read the device...
Will huawei SW do any good?
madz78 said:
Hi,
Unfortunately I'm unable enable usb debugging and can't read the device...
Will huawei SW do any good?
Click to expand...
Click to collapse
huawei SW?? i didn't get that.. can you explain please
amageek said:
huawei SW?? i didn't get that.. can you explain please
Click to expand...
Click to collapse
I mean Hisuite or any other..
madz78 said:
I mean Hisuite or any other..
Click to expand...
Click to collapse
hisuite is pretty much useless.
yeah.. I was able to enter fastboot&rescue mode with hisuite but from there i can't recover anything..
Is there any flasher that allows me to flash phone via rescue mode?
Thanks.
Hey, I might have something here, in rescue mode adb doesn't see any devices but using "fastboot devices" i get "QLF7N15615001024"
Can I work with this?
Thanks.
Just read before posting. Since you can enter fastboot just go ahead and download a fastboot flashable firmware from the various threads in this subforum or extract the images from the update.app you want to flash using huawei image extractor.
deleted
keikari said:
deleted
Click to expand...
Click to collapse
keikari are you from finland too?
gabrielkor00 said:
keikari are you from finland too?
Click to expand...
Click to collapse
Yeah
Related
Hello. Please help me. I have a Japanese version of G2 (L-01F - DoCoMo) and i tried to flash an european version of kitkat because i couldn't update in OTA. Now the phone is bricked, it is bootlooping, the Download Mode doesn't work, it shows a few of blue dots and it stays there (the phone can't be recognized on PC using the USB cable). I can enter the Recovery Mode (the grey screen with LG logo) where the phone can be read by PC and using ADB tool is shown as "recovery". I can't use fastboot.exe because the device is not being recognized. What can i do? Thank you very much.
unkn0wn68 said:
Hello. Please help me. I have a Japanese version of G2 (L-01F - DoCoMo) and i tried to flash an european version of kitkat because i couldn't update in OTA. Now the phone is bricked, it is bootlooping, the Download Mode doesn't work, it shows a few of blue dots and it stays there (the phone can't be recognized on PC using the USB cable). I can enter the Recovery Mode (the grey screen with LG logo) where the phone can be read by PC and using ADB tool is shown as "recovery". I can't use fastboot.exe because the device is not being recognized. What can i do? Thank you very much.
Click to expand...
Click to collapse
Can someone help me please ?
unkn0wn68 said:
Can someone help me please ?
Click to expand...
Click to collapse
I have the same problem. Please tell me if you can fix it.
http://forum.xda-developers.com/lg-g2/help/device-conecting-to-pc-download-mode-t2996249
ronen1n said:
I have the same problem. Please tell me if you can fix it.
http://forum.xda-developers.com/lg-g2/help/device-conecting-to-pc-download-mode-t2996249
Click to expand...
Click to collapse
Actually i'm trying to repair it since October 2014. No-one knows the solution. I went to 3 different GSM Services and they don't know what to do...
So...when i'm trying to put it in download mode it stays like this and the PC doesn't recognize it.
The only way to connect the phone to the computer is to put it in recovery mode (Backup & Restore) by holding Volume Up and Power Button at the same time with the phone turned off. It should appear something like this. The PC recognizes the phone but only in ADB. Look.
The third possible screen, which also is useless is this by typing in the CMD the following: "adb reboot recovery" (click). Here, the PC doesn't recognize the phone too.
Fastboot doesn't work.
And that's my problem. I don't know what to do.
unkn0wn68 said:
The PC recognizes the phone but only in ADB. Look.
Click to expand...
Click to collapse
If there are any custom roms that will run on your phone, adb push it to the sdcard and flash in TWRP.
iowabowtech said:
If there are any custom roms that will run on your phone, adb push it to the sdcard and flash in TWRP.
Click to expand...
Click to collapse
I have permission problems...
unkn0wn68 said:
I have permission problems...
Click to expand...
Click to collapse
?
Your screenshot above shows the device being recognized via adb in recovery. What permission problems?
Hi!
First of all, I'm sorry for my English...
I have unlocked and rooted my device (Huawei P9 lite).
I have install the TWRP bootloader and I tried to install a new costum ROM, but my device was turned off and never opened again. (Maybe: Low battery).
I try to charge my device but it didn't recognize the charger. So, I removed the battery from device (with the help of a technician) and charging it.
After all, I tried again to root and install TWRP but the device doesn't open or recognized of my PC...the only thing to do is to be recognized by the PC in fastboot mode but not allowing me to do something in the command window.
What am I doing?
First of all....
What exactly did you try to flash? Which "custom ROM" are you talking about?
Schlengge said:
First of all....
What exactly did you try to flash? Which "custom ROM" are you talking about?
Click to expand...
Click to collapse
I download the costum ROM from here: http://forum.xda-developers.com/huawei-p9lite/development/dev-cyanogenmod-13-huawei-p9-lite-t3465612
Use <[DEV] VNS-L21-L22-L31 [EUROPE] Toolkit [0.0.0.8] Bootloader/Recovery/Root/Dual-Sim> and try again to da all from begining...
- check bootloader - lock/unlock
- flash stock recovery/twrp
- root it if is necessary
- copy update.app to SDcard into dload folder and try to reflash device.
I tired... but it didn't recognized my device!
Vangeliskar1 said:
I download the costum ROM from here: http://forum.xda-developers.com/huawei-p9lite/development/dev-cyanogenmod-13-huawei-p9-lite-t3465612
Click to expand...
Click to collapse
Okay so that is interesting.
Have you followed the exact instruction on the Website of Meticulus?
The CM Rom is HIGHLY alpha and cannot be flashed without a strict preparation.
Are you able to boot your phone into fastboot mode?
Schlengge said:
Okay so that is interesting.
Have you followed the exact instruction on the Website of Meticulus?
The CM Rom is HIGHLY alpha and cannot be flashed without a strict preparation.
Are you able to boot your phone into fastboot mode?
Click to expand...
Click to collapse
No...
I can't!
It doesn't work (Volume down + power key)
Vangeliskar1 said:
No...
I can't!
It doesn't work (Volume down + power key)
Click to expand...
Click to collapse
So the device does not respond in any way?
Hmm...
Maybe refer to the CM thread and hope that someone there can help you.
Don't know if Meticulus checks out this forum section.
You said: the only thing to do is to be recognized by the PC in fastboot mode but not allowing me to do something in the command window.
So, the device is recognized by PC in fastboot mode or not?
gtdaniel said:
You said: the only thing to do is to be recognized by the PC in fastboot mode but not allowing me to do something in the command window.
So, the device is recognized by PC in fastboot mode or not?
Click to expand...
Click to collapse
Maybe...I don't know!
I have this message:
C:\adb>fastboot devices
9JT0216627000650 fastboot
C:\adb>
Ok. Try to use this tool [DEV] VNS-L21-L22-L31 [EUROPE] Toolkit [0.0.0.8] Bootloader/Recovery/Root/Dual-Sim>
And tell here what appears to work or not...
gtdaniel said:
Ok. Try to use this tool [DEV] VNS-L21-L22-L31 [EUROPE] Toolkit [0.0.0.8] Bootloader/Recovery/Root/Dual-Sim>
And tell here what appears to work or not...
Click to expand...
Click to collapse
I had tried bu it doesn't work...
I have this massage:
Drivers on PC are installed right? Just to make sure...
May be I'm wrong, there is two options to active in develloper menu ? USB debug and OEM I don't know why ?
Excuse me if I'm off topic.
Schlengge said:
Drivers on PC are installed right? Just to make sure...
Click to expand...
Click to collapse
Yes everything is allright!
I have install and Hi suite!
Phone have any control? Reboot? Power?
When you conected to PC at Devices on PC appear something?
No...it is dead....
On PC: yes! It is apeared to devices
Ok! If appear in Devices is a chance to get it back to life...
It should be recognized in fastboot mode to... (where appears with serial number).
In that stage try that tool to see if is any information visible in status (model, serial number, build number etc)
gtdaniel said:
Ok! If appear in Devices is a chance to get it back to life...
It should be recognized in fastboot mode to... (where appears with serial number).
In that stage try that tool to see if is any information visible in status (model, serial number, build number etc)
Click to expand...
Click to collapse
It is apeared at devices with that name: android Bootloader Interface
Tool?
Which tooL?
In comand window?
That tool: VNS-L21-L22-L31 [EUROPE] Toolkit [0.0.0.8] Bootloader/Recovery/Root/Dual-Sim
You attached a image with phone in fastboot mode. Can you replicate again that stage?
In that stage use that tool and see if phone appear there.
Hello, I'm new to xda, in fact I registered just to ask for help. My p9 lite got stuck on huawei logo, when i try to turn off the device it just reboots 2 times and then just stays on huawei logo. I can enter fastboot and rescue mode, but i have not enabled usb debugging and oem unlock on the device earlier. To be honest this is my first android device, in the past i used only windows phones, so you could say i'm completely new to this. Any suggestions on how to recover my phone or flash any rom into it? I'd be very glad if someone helped me find the solution to this problem. Not sure if i made a thread in the correct place, direct me if i'm mistaken
There are few different versions of P9 Lite, look at the back of the phone to the bottom to see the numbers beside VSN and let us know.
1) Also when the phone is turned off plug in the usb to a computer or charging adapter
2) Hold down volume up & power
3) Let go of the power button when you feel the buzz while still holding the volume up button
4) Download latest version & recovery.
5) Go to Settings>Developer Options>USB Debugging On
5B) If you don't see Developer Options in settings, then go to Settings>About Phone>Build Number & ( tap the Build Number untill it unlocks)
6) Update us on the status, hope it works out.
GloryNation said:
There are few different versions of P9 Lite, look at the back of the phone to the bottom to see the numbers beside VSN and let us know.
1) Also when the phone is turned off plug in the usb to a computer or charging adapter
2) Hold down volume up & power
3) Let go of the power button when you feel the buzz while still holding the volume up button
4) Download latest version & recovery.
5) Go to Settings>Developer Options>USB Debugging On
5B) If you don't see Developer Options in settings, then go to Settings>About Phone>Build Number & ( tap the Build Number untill it unlocks)
6) Update us on the status, hope it works out.
Click to expand...
Click to collapse
tried to enter recovery, still not work. can't go to developer options because phone is stuck on logo, can't power off. couldn't find any solution that works anywhere, been searching for more than 6 hours, still no use. phone model is VNS-L21 forgot to mention earlier
What exactly were you doing before this happened and does your computer recognize your phone when plugged in at all.
Try holding volume up & down together & plug phone in when it reboots on you, & report back with what you see. If anything at all.
GloryNation said:
What exactly were you doing before this happened and does your computer recognize your phone when plugged in at all.
Try holding volume up & down together & plug phone in when it reboots on you, & report back with what you see. If anything at all.
Click to expand...
Click to collapse
I tried to install nougat update, computer recognizes it only in fastboot. holding volume buttons haven't changed anything still no progress. the thing is i had installed nougat a moth or so ago and it worked fine, then rolled back to marshmallow and now this. i'm pretty sure i tried to install correct package, because it was the same i had installed earlier
Did you download a adb tool on your computer that have the 'fastboot.exe' file? If so open that folder,
Have the mouse curser hover in that folder, hold down shift & right click the mouse
Open command prompt
Connect phone as is in fastboot mode
Type adb devices & press enter
Type adb continue & press enter
Hi,
I have the same issue as ellanyx.
my phone can only be stucked while booting or if I connect my phone to a computer, I'm able to boot it in fastboot.
as ellanyx, I didn't enable usb-debug nor OEM unlock option...
so when I'm in fastboot, I type the command "fastboot oem unlock xxxxxx" (hopefully the different data needed are the correct ones mentioned on the box of the phone) I get this error message:
C:\Users\Dieu\Downloads\SRKToolHuawei-STABLE-V1.3-20160619>fastboot oem unlock xxxxx
...
FAILED (remote: Command not allowed)
finished. total time: 0.016s
and off course the other options like "fastboot flash recovery recovery.img "... doesn't work.
I can't use the adb commands neither.
when I type the commande, as mentioned above, "adb devices" or "adb continue", nothing works.
So I'm a bit desesperate
do you have any solution for this kind of issue?
thanks
Dude, so the last firmware on your phone was MM or N? If it was MM you should put stock firmware appropriate for your model in dload folder on SD card and put volume+volume-power, and thats it. If you stack on N,....then I dont know because dload method doesnt work with N, or maybe works if you can find stock firmware with recovery for N.
Regards
Unfortunately I can't update with the 3 button update otherwise it would indeed solvemy problem.
pyromana said:
Unfortunately I can't update with the 3 button update otherwise it would indeed solvemy problem.
Click to expand...
Click to collapse
Probably you didnt have correct Oeminfo for MM if dload method didnt work....Try to conect phone with Toolkit and follow procedure for flashing oeminfo and custombin, after that flash stock recovrry and b161 via dload metod. You will find it on forum here.
Regards
the procedure from SRK toolkit?
would it be possible to provide it? because I can't unlock the OEM and I didn't tick the USB debug think.
Maybe problem with the ps not phone so u can not connect with adb
Try with different pc you must have flash oem with fast boot without enable adb from phone if u in fastboot
I can only boot my phone in fastboot (vol- + power) and not in recovery (vol+ + power).
also when using the SRK toolkit, the first screen tells me to be sure that the usb debugging is enable, which I haven't done...
if I'm not mistaken, fastboot is to use the fastboot command and recovery the adb commands
the connection with fastboot works on my computer, the link is made. however when I type the command to unlock the OEM, I get an error stating that the command is not allowed.
when I use the SRK toolkit, with the different questions, he tries to connect the phone with adb and waiting.... waiting...
is there a command to reboot in recovery but from fastboot? in the otherway around it exists but it doesn't seem that from fastboot to recovery it exists.
thanks.
Alexxxx1 said:
Dude, so the last firmware on your phone was MM or N? If it was MM you should put stock firmware appropriate for your model in dload folder on SD card and put volume+volume-power, and thats it. If you stack on N,....then I dont know because dload method doesnt work with N, or maybe works if you can find stock firmware with recovery for N.
Regards
Click to expand...
Click to collapse
dload method works on N. I downgraded my phone from unofficial N update back to official MM update using this method yesterday. You just have to enable OEM at developer options on settings.
It looks like people can't be bothered to read the 1st post properly before they reply.
HE CAN NOT BOOT TO ANDROID SO HE CAN NOT ENABLE OEM OR ACTIVATE USB DEBUGGING!!!!
What he CAN do, is go into eRecovery and Fastboot.
With that in mind, I would suggest using the dload method through fastboot.
Also, make sure it is Huawei SRK Tools 2.0 that is used, as it actually asks if you are in debug mode or fastboot.
Note that there is a few bugs in SRK 2.0:
The TWRP recovery file has the wrong filename in the package, so it WILL fail unless you name it correctly.
Also, when trying to root, do NOT use the "P9 Lite" method as that WILL fail too. Use the "P9/P9 Plus" method.
I am trying to set up a complete guide that can restore the phone when it is stuck in fastboot, however I apparently went a step too far...
ellanyx said:
Hello, I'm new to xda, in fact I registered just to ask for help. My p9 lite got stuck on huawei logo, when i try to turn off the device it just reboots 2 times and then just stays on huawei logo. I can enter fastboot and rescue mode, but i have not enabled usb debugging and oem unlock on the device earlier. To be honest this is my first android device, in the past i used only windows phones, so you could say i'm completely new to this. Any suggestions on how to recover my phone or flash any rom into it? I'd be very glad if someone helped me find the solution to this problem. Not sure if i made a thread in the correct place, direct me if i'm mistaken[/QUOTE
Do you have TWRP recovery ?
---------- Post added at 09:55 AM ---------- Previous post was at 09:50 AM ----------
ellanyx said:
Hello, I'm new to xda, in fact I registered just to ask for help. My p9 lite got stuck on huawei logo, when i try to turn off the device it just reboots 2 times and then just stays on huawei logo. I can enter fastboot and rescue mode, but i have not enabled usb debugging and oem unlock on the device earlier. To be honest this is my first android device, in the past i used only windows phones, so you could say i'm completely new to this. Any suggestions on how to recover my phone or flash any rom into it? I'd be very glad if someone helped me find the solution to this problem. Not sure if i made a thread in the correct place, direct me if i'm mistaken
Click to expand...
Click to collapse
Boot into fastboot mode and flash a custom recovery by meticulus. Link : meticulus.co.vu
Then whenyou get stuck hold power and vol down button for 2 minutes the phone will reboot and then when it says that your device has been unlocked and cant be trusted then only press vol up key ( dont press power button then). The u get into huawei recovery. From that u should power off the phone. Now get a custom rom by meticulus into your device sd card ( Cyanogenmod 13 is recommended ). Then insert sd card in a powered off phone. Now press vol up and power key and flash gapps and custom rom and you are good to go.
Click to expand...
Click to collapse
So, MY question:
I have tried 4 times to get Nougat installed, but every time I got the SMALL package (1.25gb) which means it is not complete.
I decided to try ONE more time, but think I have made a serious mistake.
I was on B161 and tried to downgrade to B160 without upgrading to Nougat first.
This has caused my phone to be stuck at boot with the message "Your device is booting now..."
I can NOT get into eRecovery or fastboot no matter what I do.
If I just leave the phone, then it discharge very fast, but as soon as I plug it in, it starts up and gets stuck at the same screen again.
Does anyone have ANY idea about how I can get out of this problem?
UPDATE:
I have managed to boot to fastboot while connected to my pc.
The phone is unlocked but FRP is LOCKED, which means I can't flash anything.
I read about using Miracle Loader to remove the FRP lock, but it can't "see" my phone. Maybe I am doing it wrong?
SnowmanDK said:
So, MY question:
I have tried 4 times to get Nougat installed, but every time I got the SMALL package (1.25gb) which means it is not complete.
I decided to try ONE more time, but think I have made a serious mistake.
I was on B161 and tried to downgrade to B160 without upgrading to Nougat first.
This has caused my phone to be stuck at boot with the message "Your device is booting now..."
I can NOT get into eRecovery or fastboot no matter what I do.
If I just leave the phone, then it discharge very fast, but as soon as I plug it in, it starts up and gets stuck at the same screen again.
Does anyone have ANY idea about how I can get out of this problem?
UPDATE:
I have managed to boot to fastboot while connected to my pc.
The phone is unlocked but FRP is LOCKED, which means I can't flash anything.
I read about using Miracle Loader to remove the FRP lock, but it can't "see" my phone. Maybe I am doing it wrong?
Click to expand...
Click to collapse
Try to relock and then unlock the bootloader again. And make sure oem unlocking is enabled in dev options
Arsaam said:
Try to relock and then unlock the bootloader again. And make sure oem unlocking is enabled in dev options
Click to expand...
Click to collapse
Please read my previous post again
I can NOT boot normally. And as FRP is locked, then I can't relock or unlock the bootloader.
SnowmanDK said:
Please read my previous post again
I can NOT boot normally. And as FRP is locked, then I can't relock or unlock the bootloader.
Click to expand...
Click to collapse
Go to fast boot mode and from their try to flash meticulus recovery.
You can also try the adb method as well.
Visit meticulus.co.vu
Hello, I've bought the HTC U Ultra for my birthday at a very good price (250€) and I'm very satisfied about this phone!
Only, it's been 3 months since I try to root without any success. I can not find the "fastboot" mode in the bootloader and I do not know how.
Yet I followed all the tutorials to the letter (French expression I do not know if you go to understand ... x)) but I have never reached that point. I have the ADBs and all the other files needed.
Also, I made all the updates at the first launch of the phone. Is that why it's blocked?
Thank you in advance.
PS: I also unlocked the bootloader in the development options.
PS n°2: I post here because the French forums are desperate desert for this phone.
Hold both volume down + power together for around 10 seconds. Your phone will vibrate after that. You will then enter download mode, which is actually fastboot.
bc Yume said:
Hold both volume down + power together for around 10 seconds. Your phone will vibrate after that. You will then enter download mode, which is actually fastboot.
Click to expand...
Click to collapse
Ok, but when I want to unlock the bootloader using htcdev, I have < waiting for device > when i enter fastboot oem get_identifier_token.
SofianeLasri said:
Ok, but when I want to unlock the bootloader using htcdev, I have < waiting for device > when i enter fastboot oem get_identifier_token.
Click to expand...
Click to collapse
The computer is unable to recognise your phone. Maybe another port.
bc Yume said:
The computer is unable to recognise your phone. Maybe another port.
Click to expand...
Click to collapse
my device is recognize when it's start, but when it reboot to bootloader, abd / fastboot lost the connection. :/
I've tried with all of my ports.
SofianeLasri said:
my device is recognize when it's start, but when it reboot to bootloader, abd / fastboot lost the connection. :/
I've tried with all of my ports.
Click to expand...
Click to collapse
Are you sure you have USB Debugging on and you are using ADB driver from Google, not the one comes from HTC Sync?
bc Yume said:
Are you sure you have USB Debugging on and you are using ADB driver from Google, not the one comes from HTC Sync?
Click to expand...
Click to collapse
I use minimal adb 1.4.2 and i don't installed htc sync.
I use adb command line directly from Android Developers and have absolutely no problem. Maybe uninstall minimal adb and try that one. I can't help you with something I am not familiar with.
bc Yume said:
I use adb command line directly from Android Developers and have absolutely no problem. Maybe uninstall minimal adb and try that one. I can't help you with something I am not familiar with.
Click to expand...
Click to collapse
Yes but I must to download a lot of GB to user these abd. :/
I've just install htc sync, I tell you more if it work.
UPDATE : Oh it work! x) I never thought it would work! I thought htc sync was a software like those samsull that block the phone.
cool but i've now s-on and a i can"t install twrp with this. x)
SofianeLasri said:
cool but i've now s-on and a i can"t install twrp with this. x)
Click to expand...
Click to collapse
You can install TWRP as long as your bootloader is unlocked, regardless of the status of S-ON or S-OFF
SofianeLasri said:
cool but i've now s-on and a i can"t install twrp with this. x)
Click to expand...
Click to collapse
double check "Allow USB debugging" for the computer. From Developers "Revoke USB debugging Auth" . Unplug & plug back USB cable should come up with dialog box for auth. You may (not sure) this from cmd: adb reboot fastboot which could come up with error msg: "error: device unauthorized. This adbd's $ADB_VENDOR_KEYS is not set; try 'adb kill-server' if that seems wrong. Otherwise check for a confirmation dialog on your device."
You cant find fastboot mode because it is now called download mode...
Hello, im new to the forums and i would like to get some help with this huawei on what to do. I recieved this phone already bricked from a friend, so i would like to see if i can make it work again. I dont know how the phone got bricked and i have no idea of what to do. The problem is that the phone starts in the huawei logo and then goes to a black screen and turns itself off again. The phone doesnt make it past that point. I tried to make a reset from recovery, but it doesnt work. In download mode i tried to download the latest recovery, but it says failed to download. In fastboot mode the phone says "Phone unlocked" in red letters and "FRP locked" in green letters.
Any idea of what to do in order to recover the phone ?.
BrattPitlord said:
Hello, im new to the forums and i would like to get some help with this huawei on what to do. I recieved this phone already bricked from a friend, so i would like to see if i can make it work again. I dont know how the phone got bricked and i have no idea of what to do. The problem is that the phone starts in the huawei logo and then goes to a black screen and turns itself off again. The phone doesnt make it past that point. I tried to make a reset from recovery, but it doesnt work. In download mode i tried to download the latest recovery, but it says failed to download. In fastboot mode the phone says "Phone unlocked" in red letters and "FRP locked" in green letters.
Any idea of what to do in order to recover the phone ?.
Click to expand...
Click to collapse
Hello and welcome !
Just thinking you should try to start a fresh & clean install
rolling back to android 6 regardless of the current firmware.
Took a look inside the UNIFIED HELP THREAD but didn't find
any L23 rollback package...
However, I found another LINK that looks promising.
Good luck :fingers-crossed:
For further explanations try asking here.
Dadditz said:
Hello and welcome !
Just thinking you should try to start a fresh & clean install
rolling back to android 6 regardless of the current firmware.
Took a look inside the UNIFIED HELP THREAD but didn't find
any L23 rollback package...
However, I found another LINK that looks promising.
Good luck :fingers-crossed:
For further explanations try asking here.
Click to expand...
Click to collapse
Nice, i will try this and inform back later.
Dadditz said:
Hello and welcome !
Just thinking you should try to start a fresh & clean install
rolling back to android 6 regardless of the current firmware.
Took a look inside the UNIFIED HELP THREAD but didn't find
any L23 rollback package...
However, I found another LINK that looks promising.
Good luck :fingers-crossed:
For further explanations try asking here.
Click to expand...
Click to collapse
Well it didnt work. It says "incompatibility with this version"
BrattPitlord said:
Well it didnt work. It says "incompatibility with this version"
Click to expand...
Click to collapse
Hi,
you should use the follovinq commands in fastboot mode and then post the results please:
fastboot oem get-build-number
fastboot oem get-product-model
fastboot getvar version
fastboot getvar vendorcountry
Can you access Recovery ? (Power + Volume Up)
-Alf- said:
Hi,
you should use the follovinq commands in fastboot mode and then post the results please:
fastboot oem get-build-number
fastboot oem get-product-model
fastboot getvar version
fastboot getvar vendorcountry
Can you access Recovery ? (Power + Volume Up)
Click to expand...
Click to collapse
im new to this, so i put those commands in windows CMD with the phone connected or how ?
I can get to the stock recovery from huawei.
BrattPitlord said:
im new to this, so i put those commands in windows CMD with the phone connected or how ?
I can get to the stock recovery from huawei.
Click to expand...
Click to collapse
Use ADB commands.
Open developers option and turn on the USB debugging. Connect your device to PC in MTP/FILES mode. Run command
ADB reboot bootloader
(the device will reboot to fastboot mode)
Now you can type fastboot commands.
-Alf- said:
Use ADB commands.
Open developers option and turn on the USB debugging. Connect your device to PC in MTP/FILES mode. Run command
ADB reboot bootloader
(the device will reboot to fastboot mode)
Now you can type fastboot commands.
Click to expand...
Click to collapse
How do i turn debugging if the phone is bricked ? I cant get past the huawei logo. However, i do have access to fastboot mode.
BrattPitlord said:
How do i turn debugging if the phone is bricked ? I cant get past the huawei logo. However, i do have access to fastboot mode.
Click to expand...
Click to collapse
Oh, sorry, my mistake . Okay, install on your PC "Minimal ADB and fastboot" , open it , connect the device in fastboot mode, and run commands.