Database Users

Phone is working fine, but Odin says "There is no PIT partition" when I try to flash.

Phone is working fine, but Odin says "There is no PIT partition" when I try to flash.
I have a GT-I9505 with the MDA version firmware, region EVR.
I've flashed it previously, successfully, to the latest ME2 firmware, but then I installed Chainfire3D which soft-bricked it.
I recovered using Kies firmware recovery, did a factory reset/cache wipe, have rooted the phone again... but now Odin won't flash the phone!
It says "There is no PIT partition", and when I try to re-partition using the PIT file from this thread, it just says "complete(write) operation failed".
I've tried Odin 1.8, 3.04, 3.07... all the same.
The phone is currently working fine and is rooted! I just want to flash to a newer firmware, is all.
Any thoughts?

Flash .pit file with the firmware, not alone make sure re-partition is ticked
Sent from my Galaxy using xda premium

samersh72 said:
Flash .pit file with the firmware, not alone make sure re-partition is ticked
Sent from my Galaxy using xda premium
Click to expand...
Click to collapse
I was doing both those things. Strangely, it worked when I used another computer! Thanks anyway.

I am having similar problems. Any other suggestions?
I'm trying to root my S4 for the first time. Just had the S4 factory reset itself before starting this attempt.
Seems like the USB connection keeps resetting. I don't have this problem on any other device and I've tried swapping USB cords as well as USB ports. Tried both USB 2.0 and 3.0 ports. I keep getting the same problems. I've even tried including the PIT file for re-partitioning. Even the Kies connection keeps resetting. Kies trouble shooting the USB connection resulting in reloading some drivers but that didn't have any effect.
ODIN output below:
<ID:0/010> Added!!
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Removed!!
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/010> Added!!
<ID:0/010> Removed!!
<ID:0/011> Added!!
<ID:0/011> Removed!!
<ID:0/011> Added!!
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Get PIT for mapping..
<ID:0/011> Removed!!
<ID:0/011> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/011> Added!!
Now, searching lead me to a thread for I think the S3 and they were saying these kinds of problems were defective motherboards on the phone. Do I need to take my phone back to Verizon for warranty replacement? It's not even a week old yet.

0reo said:
I am having similar problems. Any other suggestions?
I'm trying to root my S4 for the first time. Just had the S4 factory reset itself before starting this attempt.
Seems like the USB connection keeps resetting. I don't have this problem on any other device and I've tried swapping USB cords as well as USB ports. Tried both USB 2.0 and 3.0 ports. I keep getting the same problems. I've even tried including the PIT file for re-partitioning. Even the Kies connection keeps resetting. Kies trouble shooting the USB connection resulting in reloading some drivers but that didn't have any effect.
ODIN output below:
<ID:0/010> Added!!
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Removed!!
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/010> Added!!
<ID:0/010> Removed!!
<ID:0/011> Added!!
<ID:0/011> Removed!!
<ID:0/011> Added!!
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Get PIT for mapping..
<ID:0/011> Removed!!
<ID:0/011> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/011> Added!!
Now, searching lead me to a thread for I think the S3 and they were saying these kinds of problems were defective motherboards on the phone. Do I need to take my phone back to Verizon for warranty replacement? It's not even a week old yet.
Click to expand...
Click to collapse
uninstall driver then re-install it. make sure kies is not running. flash pit file with the firmware in odin

samersh72 said:
uninstall driver then re-install it. make sure kies is not running. flash pit file with the firmware in odin
Click to expand...
Click to collapse
For the record, I just convinced the local VZW store to swap me a NIB S4 as a warranty replacement. The new S4 is giving me the exact same problem so in all likelihood the phone is not my problem.
Going to try removing and reinstalling the drivers on the PC again.
Does USB debugging need to be checked / unchecked for ODIN to work?

0reo said:
For the record, I just convinced the local VZW store to swap me a NIB S4 as a warranty replacement. The new S4 is giving me the exact same problem so in all likelihood the phone is not my problem.
Going to try removing and reinstalling the drivers on the PC again.
Does USB debugging need to be checked / unchecked for ODIN to work?
Click to expand...
Click to collapse
NO NEED to check it. a lot of users brick their phones and can not boot to check usb debugging. so they went directly to odin flash and it was good to go :good:

0reo said:
For the record, I just convinced the local VZW store to swap me a NIB S4 as a warranty replacement. The new S4 is giving me the exact same problem so in all likelihood the phone is not my problem.
Going to try removing and reinstalling the drivers on the PC again.
Does USB debugging need to be checked / unchecked for ODIN to work?
Click to expand...
Click to collapse
Hi,
USB debugging needs to be ticked.

OK, I uninstalled and reinstalled the drivers and still get the same problems. Any other ideas?

0reo said:
OK, I uninstalled and reinstalled the drivers and still get the same problems. Any other ideas?
Click to expand...
Click to collapse
Hi,
Did you reboot your PC?

malybru said:
Hi,
Did you reboot your PC?
Click to expand...
Click to collapse
Yes, a number of times at every stage one would think it would make any difference. It didn't make any difference.
I did finally get my phone rooted. While I can't say for certain, it seems like the S4 needed to be booted normally, then connected via USB, then let Win7 auto install several drivers, then I initiated bhp090808's all-in-one root tool which rebooted the phone into ODIN mode. ODIN was then successful.
Contrast that with having the S4 disconnected from USB and manually booting into ODIN mode, then connect USB, then let Win7 install drivers, then initiate ODIN to start. That sequence gave me all the problems.
Thanks for the replies though. I do appreciate your willingness to help.

Solved same problem this way:
1) Connected phone by original cable directly to rear USB port
2) Turn off Kies (no need to uninstall)
3) Stopped 2 kies processes which still run even if kies is off.
4) There must be item "Samsung Android Phone" and cascaded item "Samsung android ADB interface" in device manager.
5) Enable USB Debugging in phone.
6) I had unchecked item "Check installed apps from ADB by USB" - Not sure if it is necessary.
7) When you connect phone there has to be popup with question: "Allow USB debugging from this computer?" followed by computer signature.
Check always, answer yes.
8) Use old Odin 3 V. 1.85
i9505+stock firmware+win7sp1

On pit partition found
samersh72 said:
I flashed cm 10.1 on my SAMSUNG Galaxy Ace Plus.Now I want to come back to my stock rom . I downloaded the stock rom and I am trying to flash it using ODIN.But I get the message that ON PIT PARTITION FOUND.
Click to expand...
Click to collapse
aa
---------- Post added at 08:53 AM ---------- Previous post was at 08:48 AM ----------
samersh72 said:
Flash .pit file with the firmware, not alone make sure re-partition is ticked
Sent from my Galaxy using xda premium
Click to expand...
Click to collapse
mpalka said:
Solved same problem this way:
1) Connected phone by original cable directly to rear USB port
2) Turn off Kies (no need to uninstall)
3) Stopped 2 kies processes which still run even if kies is off.
4) There must be item "Samsung Android Phone" and cascaded item "Samsung android ADB interface" in device manager.
5) Enable USB Debugging in phone.
6) I had unchecked item "Check installed apps from ADB by USB" - Not sure if it is necessary.
7) When you connect phone there has to be popup with question: "Allow USB debugging from this computer?" followed by computer signature.
Check always, answer yes.
8) Use old Odin 3 V. 1.85
i9505+stock firmware+win7sp1
Click to expand...
Click to collapse
]I flashed cm 10.1 on my SAMSUNG Galaxy Ace Plus.Now I want to come back to my stock rom . I downloaded the stock rom and I am trying to flash it using ODIN.But I get the message that ON PIT PARTITION FOUND

Sagar6699 said:
I flashed cm 10.1 on my SAMSUNG Galaxy Ace Plus.Now I want to come back to my stock rom . I downloaded the stock rom and I am trying to flash it using ODIN.But I get the message that ON PIT PARTITION FOUND
Click to expand...
Click to collapse
flash pit with the firmware http://forum.xda-developers.com/showthread.php?t=2065046

Re-Partition
samersh72 said:
flash pit with the firmware http://forum.xda-developers.com/showthread.php?t=2065046
Click to expand...
Click to collapse
Thanks!!
But now there is another problem........
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S7500DDLD1_S7500ODDLD2_S7500DDLD1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009>
<ID:0/009> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
PLZ HELP!!!!!!!!

probably solve with this
Well I did thgis ... searched another firmware mewer same carrier .. and I rebooted the Pc ..Nothing
But on a forum external some dude sayd ok .. If you use front USB ports theese are coted as external USB and they don't are recognized as internal USB hubs so change to a back side usb and will work I did and now after waiting like 5 minutes the process started my phone is under process restarting now ... And Voloa .. the new firmware,

Thanks for that suggestion. Switching to the back USB ports worked for me.
pisicutumic said:
Well I did thgis ... searched another firmware mewer same carrier .. and I rebooted the Pc ..Nothing
But on a forum external some dude sayd ok .. If you use front USB ports theese are coted as external USB and they don't are recognized as internal USB hubs so change to a back side usb and will work I did and now after waiting like 5 minutes the process started my phone is under process restarting now ... And Voloa .. the new firmware,
Click to expand...
Click to collapse

Moritzio said:
Thanks for that suggestion. Switching to the back USB ports worked for me.
Click to expand...
Click to collapse
and me as well!
thanks alot! :laugh::laugh:

yanivnn said:
and me as well!
thanks alot! :laugh::laugh:
Click to expand...
Click to collapse
And me too!

Moritzio said:
Thanks for that suggestion. Switching to the back USB ports worked for me.
Click to expand...
Click to collapse
For me too, you are genious!

[Q] Note 3 SM-900 Stuck on Splash Logo (Download Mode Works)

Hi Everyone,
Having a problem here with a SM-900 Note 3 sent back to the US here by a relative. A relative asked me to purchase it off Amazon with their credit card (prime shipping), so it comes from a trustworthy source. AFAIK the phone was unrooted (Knox counter 0) and apps were installed through the play store. The phone is stuck at the initial "Samsung Galaxy Note 3 SM-900" screen. The logo is not steady, instead it keeps flashing every 3 seconds. Recovery mode does not work, or at least the phone keeps flashing the logo. Download Mode, however, works and the phone stays turned on steady. Kies keeps saying connecting and Jodin3 keeps saying my phone isn't connected. I have tried all 4 ports and 3 separate usb cables. I don't have access to a Windows machine only an iMac. I'm not sure what is wrong. I'm going to try downloading odin to my mac to see if it will work. If all else fails, I plan on contacting Samsung to see if they will fix it seeing as it was purchased only 4 months ago. Any help is greatly appreciated.

Hiya Buddy said:
Hi Everyone,
Having a problem here with a SM-900 Note 3 sent back to the US here by a relative. A relative asked me to purchase it off Amazon with their credit card (prime shipping), so it comes from a trustworthy source. AFAIK the phone was unrooted (Knox counter 0) and apps were installed through the play store. The phone is stuck at the initial "Samsung Galaxy Note 3 SM-900" screen. The logo is not steady, instead it keeps flashing every 3 seconds. Recovery mode does not work, or at least the phone keeps flashing the logo. Download Mode, however, works and the phone stays turned on steady. Kies keeps saying connecting and Jodin3 keeps saying my phone isn't connected. I have tried all 4 ports and 3 separate usb cables. I don't have access to a Windows machine only an iMac. I'm not sure what is wrong. I'm going to try downloading odin to my mac to see if it will work. If all else fails, I plan on contacting Samsung to see if they will fix it seeing as it was purchased only 4 months ago. Any help is greatly appreciated.
Click to expand...
Click to collapse
If you were using a Windows PC, install Kies 3 to get a correct driver to be installed, then download a stock firmware for your device and flash via Odin. That could help to fix the problem.
I'm not familiar with iMac so I don't know what software can be a replacement for the Odin.
You can try Heimdall.

vndnguyen said:
If you were using a Windows PC, install Kies 3 to get a correct driver to be installed, then download a stock firmware for your device and flash via Odin. That could help to fix the problem.
I'm not familiar with iMac so I don't know what software can be a replacement for the Odin.
You can try Heimdall.
Click to expand...
Click to collapse
I managed to go over a friend's house and use his windows machine. I got the correct file and used Odin and it said "PASS". Unfortunately, the Note 3 is still having the same problem with the splash logo flashing every three seconds. Not sure whats wrong. Could it be hardware related? The battery contacts on the phone are fine. I don't think there is anything wrong with the battery itself because download mode works just fine. It seems to start the phone up its having trouble getting past the initial splash screen. Safe mode is not working either. Looks like I might have to put in a call to Samsung for warranty repair.

Hiya Buddy said:
Hi Everyone,
Having a problem here with a SM-900 Note 3 sent back to the US here by a relative. A relative asked me to purchase it off Amazon with their credit card (prime shipping), so it comes from a trustworthy source. AFAIK the phone was unrooted (Knox counter 0) and apps were installed through the play store. The phone is stuck at the initial "Samsung Galaxy Note 3 SM-900" screen. The logo is not steady, instead it keeps flashing every 3 seconds. Recovery mode does not work, or at least the phone keeps flashing the logo. Download Mode, however, works and the phone stays turned on steady. Kies keeps saying connecting and Jodin3 keeps saying my phone isn't connected. I have tried all 4 ports and 3 separate usb cables. I don't have access to a Windows machine only an iMac. I'm not sure what is wrong. I'm going to try downloading odin to my mac to see if it will work. If all else fails, I plan on contacting Samsung to see if they will fix it seeing as it was purchased only 4 months ago. Any help is greatly appreciated.
Click to expand...
Click to collapse
1. You will have to download one of the latest firmware of: HERE. I supose you don't know the CSC (country CODE) of your device. We don't know what firmware had your device either. Try to flash one of the newest for avoid active KNOX to 0x1 in future if you have to come back to one older firmware. Flash the firmware of the correct country if you know it ofc.
2. ODIN don't works in Mac.... use HEIMDALL. Lil guide: HERE

Hiya Buddy said:
I managed to go over a friend's house and use his windows machine. I got the correct file and used Odin and it said "PASS". Unfortunately, the Note 3 is still having the same problem with the splash logo flashing every three seconds. Not sure whats wrong. Could it be hardware related? The battery contacts on the phone are fine. I don't think there is anything wrong with the battery itself because download mode works just fine. It seems to start the phone up its having trouble getting past the initial splash screen. Safe mode is not working either. Looks like I might have to put in a call to Samsung for warranty repair.
Click to expand...
Click to collapse
Can you show the Odin screenshot? And also the full Odin log file?

UPDATE:
Vndnguyen; Sorry for the long wait as the past couple of weeks have been hectic with a family member in the hospital. Samsung Customer Support was obviously unhelpful but someone managed to find the true country of origin of my phone. They said (Samsung CS) based on IMEI it is from Taiwan. Now that I know the proper firmware I have downloaded the corresponding country version from Sam Mobile. Currently leaving Odin running to see if that does anything to fix it. Regardless, I will still post a screen shot and the log file.
P.S. It was confirmed the battery was not the problem, a Samsung Rep at a Best Buy store pulled out a battery from a working display Note 3 and used it in mine, but still no dice.

I tried the Taiwan firmware from Sam Mobile (N900ZSUENI3_N900OZSENI3_N900XXUENG1_HOME.tar.md5) but Odin reported fail. Even after 3 attempts it still reported fail. After contacting the third party seller via Amazon, they replied that the Note 3 was meant for Latin America. I picked one of the countries (Panama: N900UBUENJ2_N900UWAENJ2_N900UBUENG1_HOME.tar.md5) and Odin reported Pass! But it still keeps flashing at the boot screen.
This is the log for the Panama Firmware:
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900UBUENJ2_N900UWAENJ2_N900UBUENG1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> modem.bin
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Removed!!
I'm not sure about "removed" because I left the Note 3 plugged in.
Here is the log for the Taiwan Firmware:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900ZSUENI3_N900OZSENI3_N900XXUENG1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> system.img
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> modem.bin
<ID:0/004> param.bin
<ID:0/004> sboot.bin
<ID:0/004> cache.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Here is a screenshot of Odin. With the phone still plugged in to the computer.

Is my S7 Edge Bricked?

Think my s7 edge is bricked. wont flash anything via odin. comes with the same log every time with a fail
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1101)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> RQT_CLOSE !!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
anything i can do?

How did you get to this point? Give us more details.

wweecw123 said:
Think my s7 edge is bricked. wont flash anything via odin. comes with the same log every time with a fail
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1101)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> RQT_CLOSE !!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
anything i can do?
Click to expand...
Click to collapse
First of all what are you trying to Do??? Second can you boot to download mode
Third what device and version do you have.
You're not giving enough information
"POWWWWER...SPEEEEED !"
Sent from my Echoe Powered Stig driven G935F

Please help
I need help, I have similar problem as the OP. I will give more background so hopefully someone can help me
I have a SM-G935W8 - TELUS - Canada
I rooted and successfully installed Custom Recovery TWRP using ODIN. I used it for a few days then changed my mind and tried to flash the STOCK ROM back to the S7 Edge using once again the ODIN 3.11.1.
While it downloading into the phone, every time it gets to the SYSTEM file it would failed. Since the first time it failed, I forced reboot my device by doing the (POWER + DOWN + HOME) it will bring me to the bring screen that says "An ERROR has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC Software" .
So I downloaded the Smart Switch and plugged my device into the PC and tried using the emergency recovery "initialization" but as soon as it finished with the download of the software, I think it doesn't recognize the device it would ask me to put the device into download mode even though it is already in download mode. It stuck at 0% update so once again I have to abandon it.
I tried ODIN again and again but it would just failed at the SYTEM. I have tried downloading and using multiple different version of the SM-G935W8 firmware from different carriers but still no luck. I tried various version of ODIN, nothing.
I am still able to get into the download mode by POWER + DOWN + HOME if I keep holding on until that screen pop up to ask me to press UP to continue.

2k11pro4x said:
I need help, I have similar problem as the OP. I will give more background so hopefully someone can help me
...
I am still able to get into the download mode by POWER + DOWN + HOME if I keep holding on until that screen pop up to ask me to press UP to continue.
Click to expand...
Click to collapse
Try plugging the cable directly into your computer, no hob or anything. Also try a different cable.

qwewqa said:
Try plugging the cable directly into your computer, no hob or anything. Also try a different cable.
Click to expand...
Click to collapse
You are right. I have tried many things but the simpliest thing like trying a different cable I haven't. The device is connecting directly into the PC. I also tried a new USB port now. I'll report back shortly. Thanks
---------- Post added at 01:55 AM ---------- Previous post was at 01:48 AM ----------
BIG BIG THANK YOU!!!
I can't believe it is THAT EASY. The whole time it turns out it's the friggin CABLE.
I bought an aftermarket cable that is 10 feet long so I can use while I lay watching TV but I guess it's cheap cable so it doesn't perform as well. I plugged in the original cable that it came with and it worked RIGHT AWAY and now i'm back with Stock ROM. Thanks again.

Yes, cables can be the problem. Glad you made it
Sent from my SM-N935F using Tapatalk

2k11pro4x said:
You are right. I have tried many things but the simpliest thing like trying a different cable I haven't. The device is connecting directly into the PC. I also tried a new USB port now. I'll report back shortly. Thanks
---------- Post added at 01:55 AM ---------- Previous post was at 01:48 AM ----------
BIG BIG THANK YOU!!!
I can't believe it is THAT EASY. The whole time it turns out it's the friggin CABLE.
I bought an aftermarket cable that is 10 feet long so I can use while I lay watching TV but I guess it's cheap cable so it doesn't perform as well. I plugged in the original cable that it came with and it worked RIGHT AWAY and now i'm back with Stock ROM. Thanks again.
Click to expand...
Click to collapse
Over a certain distance most USB cables data will break down. It may be OK for power and some light weight data transfer, but always use a legit cable for flashing etc.
Sent from my SM-G935F using XDA-Developers mobile app

[Kernel is not Seandroid Enforcing] bootloop

I really messed up my phone :/
Hi, so about one month ago I decided to root my phone, but I did not know what I was doing since it was my first time and I was VERY confused. I ended up causing my phone to go into a bootloop, I'd first to even get it to work make it I'd make it go into download mode then restart from there. It'd just say in the top right corner "kernel is not seandroid enforcing" then afterwords it'd flicker the bottom buttons to just turn off completely. Any advice or help would be amazing , I won't mind spending time just to fix this so I'm all open

I recomend to flash the stock firmware on your phone.
Get the firmware file from fw.updato.com(fast but sometimes website is down)
Or
sammobile.com(slow but reliable)
Since you already sayd you tryed to root ur phone i suppose you know where to get odin3
Extract the firmware zip file y downloaded inside should be a .tar file put that in AP in odin and click start
Also i recomend a wipe but in theory it should* start working without.
Hope this helped you

Rainbow_Dash said:
I recomend to flash the stock firmware on your phone.
Get the firmware file from fw.updato.com(fast but sometimes website is down)
Or
sammobile.com(slow but reliable)
Since you already sayd you tryed to root ur phone i suppose you know where to get odin3
Extract the firmware zip file y downloaded inside should be a .tar file put that in AP in odin and click start
Also i recomend a wipe but in theory it should* start working without.
Hope this helped you
Click to expand...
Click to collapse
I've tried it before but I'll try it again, nothing really happens when I do it but mabey It'll work this time. I'll tell you whether it work or not

Nooooxa said:
I've tried it before but I'll try it again, nothing really happens when I do it but mabey It'll work this time. I'll tell you whether it work or not
Click to expand...
Click to collapse
Quick edit, my phone doesn't show up on the ID:COM area at all, I've tried other cables but it just won't work at all. I'm pretty sure it's from my phone itself and not the program

Nooooxa said:
Quick edit, my phone doesn't show up on the ID:COM area at all, I've tried other cables but it just won't work at all. I'm pretty sure it's from my phone itself and not the program
Click to expand...
Click to collapse
Oh no I forgot y need to have installed special drivers otherwise in some cases it won't show up. Get it from here în my experience first time it can take up to 1 hour for phone to be recognized. Also make sure ur phone is well enterd in download mode (volume down+home+volume up+power) a blueish screen appears and volume up again) there is no way it's bcuz of the phone. Also use the cable that came with the device and if it still doesn't work (for some reason) try in another pc (or mac)

Rainbow_Dash said:
Oh no I forgot y need to have installed special drivers otherwise in some cases it won't show up. Get it from here în my experience first time it can take up to 1 hour for phone to be recognized. Also make sure ur phone is well enterd in download mode (volume down+home+volume up+power) a blueish screen appears and volume up again) there is no way it's bcuz of the phone. Also use the cable that came with the device and if it still doesn't work (for some reason) try in another pc (or mac)
Click to expand...
Click to collapse
I got the driver installed and so far it's actually being able to connect ! but I have no luck at all, I put it in downloading mode, opened up oden then at a certain point my phone randomly went black then said "An error occurred while updating the device software. Use the Emergency recovery function in the smart switch PC software" Which I did end up doing but even while using that it will randomly shut off :/. Here's the oden log
"<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)"

Nooooxa said:
I got the driver installed and so far it's actually being able to connect ! but I have no luck at all, I put it in downloading mode, opened up oden then at a certain point my phone randomly went black then said "An error occurred while updating the device software. Use the Emergency recovery function in the smart switch PC software" Which I did end up doing but even while using that it will randomly shut off :/. Here's the oden log
"<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)"
Click to expand...
Click to collapse
Nevermind I found the issue! For some reason, my phone wasn't charged and my computer couldn't charge it enough. Dude, I can't thank you enough, I've been at this for a month now and never thought of going onto a forum. I was about to pay some guy $30 to fix it for me.

Nooooxa said:
I really messed up my phone :/
Hi, so about one month ago I decided to root my phone, but I did not know what I was doing since it was my first time and I was VERY confused. I ended up causing my phone to go into a bootloop, I'd first to even get it to work make it I'd make it go into download mode then restart from there. It'd just say in the top right corner "kernel is not seandroid enforcing" then afterwords it'd flicker the bottom buttons to just turn off completely. Any advice or help would be amazing , I won't mind spending time just to fix this so I'm all open
Click to expand...
Click to collapse
do you have flahed a custom rom?
or flash custom kernel? like audax kernel?

Bricked Tablet With 1 Click Root App

So awhile back I bricked my Samsung Galaxy Tablet 4 by installing a 1 click root app and later restarting my tablet. I haven't been able to fix it since. I was using an app because of the locked bootloader. Is there a way to fix this? The tablet uses the T337AUCU2BOH4 firmware which I think I was able to find through google, although it said it only worked for nonrooted apps which I didn't understand.

You could search about Odin. With it you can install samsung stock firmware on your device, if you can still boot to download mode. Also it's best to avoid 1 click root apps(if possible) they seem to cause problems very often.

keikari said:
You could search about Odin. With it you can install samsung stock firmware on your device, if you can still boot to download mode. Also it's best to avoid 1 click root apps(if possible) they seem to cause problems very often.
Click to expand...
Click to collapse
I found the firmware files here
I set my device to download mode and chose the file for the BL, AP, CP, and CSC section of Odin3 and click start. The program than stalls at SetupConnection and fails. I run Odin3 a second time and it's now stalling at Initialization. Later attempts I get a log with "Can't open the serial(COM) port". I Googled something that suggested I download the USB driver for the tablet so I downloaded this, but it didn't help.
Here's my log:
Code:
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Here's my log after running Odin3 a second time
Code:
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
Later attempts it now does this:
Code:
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
Can any help me figure out what I'm doing wrong here? I don't really know much about android so this stuff is all new to me.

WeirdoSarah said:
I found the firmware files here
I set my device to download mode and chose the file for the BL, AP, CP, and CSC section of Odin3 and click start. The program than stalls at SetupConnection and fails. I run Odin3 a second time and it's now stalling at Initialization.
Can any help me figure out what I'm doing wrong here? I don't really know much about android so this stuff is all new to me.
Click to expand...
Click to collapse
This guide says that you should only choose file for the AP, but I have no idea is that fix for your problem.
https://forum.xda-developers.com/tab-4/general/guide-how-to-restore-stock-firmware-t2979006

keikari said:
This guide says that you should only chose the file for the AP, but I have no idea is that fix for your problem.
https://forum.xda-developers.com/tab-4/general/guide-how-to-restore-stock-firmware-t2979006
Click to expand...
Click to collapse
Thanks for finding that! I was actually originally following that guide although I had to find the firmware files elsewhere. I tried just selecting the AP, but it didn't work. I'm still getting the same set of errors.
Edit: I restarted Odin3 and unplugged and the cord and plugged it back in and I think it's working now. It started downloading and the tablet rebooted when it was done. At first, it looked promising, but it booted to some AT&T logo in the middle and white background which scared me a little. After a minute or so it booted up to the welcome menu to configure the tablet. Thanks so much for your help!

WeirdoSarah said:
Thanks for finding that! I was actually originally following that guide although I had to find the firmware files elsewhere. I tried just selecting the AP, but it didn't work. I'm still getting the same set of errors.
Edit: I restarted Odin3 and unplugged and the cord and plugged it back in and I think it's working now. It started downloading and the tablet rebooted when it was done. At first, it looked promising, but it booted to some AT&T logo in the middle and white background which scared me a little. After a minute or so it booted up to the welcome menu to configure the tablet. Thanks so much for your help!
Click to expand...
Click to collapse
No problem. About that AT&T logo, you can get rid of it by finding "non-branded firmware" (or something like that I don't know the right term for it) or you can check if SM-T335 has same specs as your tablet(all its firmwares seem to be "non-branded"). Like with sm-t230 you can use sm-t231 roms. But be careful if you do that.
This site might have more firmwares http://forum.youmobile.org/downloads/?cat=151 thought I'm not sure have I ever tried to download from there. Atleast you can find build numbers there.
Or maybe rooting your device and changing boot animation.
Also there is a button for thanking : D (next to reply button) ---------------------------------------------------------------V