Recently my Nexus 6P got some water damage from a canoe trip (even though it was in a water "resistant" pelican case), and was not booting up. Took it to get repaired and the shop cleaned up the corrosion on the bottom of the phone where they said the water damage was. Phone booted up perfectly and everything was working great - wifi, gps, speakers, vibration motor, etc.
A few moments later my wife called me and I answered only to realize that she could not hear anything from my end. The microphone was not working. Took the phone back and they replaced the bottom PCB (daughterboard) of the phone which holds one of the main microphones.
No luck. Now I'm able to use my Nexus 6P for EVERYTHING except making phone calls, which kinda blows. I know I could use bluetooth etc. but that's not really a solution for me.
Does XDA community have any thoughts / ideas about what the problem could be and any possible solutions for me?
Thanks a ton guys!
Nathan
I think your only option is to take it back to the repair shop again.
Shop said that is all they could do for me. The daughterboard is brand new, so if the microphone is still not working, could it be something wrong with the connection to the main board? Would replacing the ribbon cable prove useful?
Thoughts appreciated!
Nathan
Without seeing the device it's very hard to say, but yeah, possibly.
I'm having the similar issue where I went to a foam paarty and got the phone wet. Fortunately everything is working fine except the proximity sensor. Sent phone to Ubreakifix for repair but tjeu couldn't find the part anywhere. Huawei/Google don't provide the replacement part & Huawei don't repair water damaged phone.
If someone could tell me where can I find the Proximity Sensor replacement will be very much appreciated.
Thanks
Related
Hi, I come on here quite a lot for information as it's an amazing resource! This time however, I'm attempting to give something back!
I experienced the "black screen on slide out" on Monday. Phone completely screwed. I've also had a few droppages and had it apart once before so there's no way warranty is gonna help!
I stripped it down and soon discovered what it is that actually fails on the ribbon. The coating had worn through due to rubbing on something during the slide out / in process. it had been playing up for a while, probably due to shorting out on the metal case, but now the tracks (aluminium?) had worn right down.....
In pic 1 i've circled the worn area. The shiny section is where i'd tried taping over it to prevent shorting, before i realised the tracks were gone.
Got an almost new one off ebay for 15 quid and, realising it was going to happen again, came up with a solution that, so far, looks like it will work....
A while back I bought some "anti rattle felt" for my car's dashboard - really thin and strong self adhesive felt to prevent squeaking joins between dash sections. I cut a piece of this and stuck it to the new ribbon. Once this stuff is on it's well stuck, by the way!
See pic 2 for the modded ribbon cable.
On reassembly everything is working just fine so far! Here's hoping that it lasts longer than 6 months this time!
Just need a new casing now as mine is decidedly second hand!
Hope this turns out to be of use to someone!
cool story bro
when i took apart my xperia to replace the housing this seemed like a really weak point in the device. glad to see someone who has had the problem has been able to fix it
Why does the screen go black?
Hi,
When the coating wears off the ribbon cable it exposes the tracks in it. when you slide the keyboard out the exposed tracks short out on the metal casing and the screen loses it's input signal.
thats whats happened on mine at least and i presume quite a few others?
HTH!
Update:
That's interesting: My phone was also losing signal with the keyboard out, and occasionally while closed up as well. It would just randomly drop to "no signal" for a few seconds.
It hasn't done it since replacing the ribbon cable.....could be coincidental of course.
I'm having the same problem
It just started a week ago and I got the phone in January off of ebay. I'm new to opening up the phone so could anyone help me find the correct tools or have a link to a site with pictured instructions?
I noticed that the sliding mechanism started to go loose about 4-5 months ago but didn't expect the screen not respond in landscape mode. I have yet to see the other symptoms you all are referring to. I would like to fix this before it get worse.
In mine case it went totaly black after one week of this problem... You have all the instruction on youtube, there is where i looked. For tools you can be inovative, but the exactly right ones come with housings from ebay, it is only 15EUR, and i bet you have some cracks so it wouldn't hurt replacing. That is what i did, along with ordering new sliding mechanizm, and new ribbon cable.
I am open for ideas to prevent my ribbon cable from being cut at it weakest point again.
I'm assuming my flex ribbon went bad yesterday, since sliding the keypad out causes my screen to shut off.
Already ordered a cable off ebay and will attempt to replace it myself :O
Replaced my flex ribbon cable with one I bought on eBay. The screen doesn't turn on at all now, which leads me to believe the cable I was sent is defective. Put the old one back in and it works okay, less landscape mode. ughhh what a pain.
great tips! my input is I bought a case off of ebay that was ~60$ and everything actually fit fine for me...so I wouldn't discount every seller but you do get what you pay for, the 15$ cases are probablly the ones that will give you problems
I working in a mobilephone repair center if anyone need help drop me a priv... i able to get 2nd hand or even brand new components
Replaced the flex ribbon cable -
I got my flex ribbon cable a few weeks ago and took it to my local repair shop. They replaced it but the LCD screen/optical joystick receives no power. The touchscreen and everything else on the phone works just fine now. I thought it was a defective item so it was exchanged with a new one.
Got the repair shop to replace it again and the outcome still remains the same as the first.
Theres no light coming from the screen nor the side illumination.
I just told the repair shop to just place the original back in for the mean time.
Before the repairs, there would be a flicker of white light and random illuminations. Now there's no lights at all except the power botton.
Could it be defective a batch that the seller was sending out? or the repair shop's mistake and is playing dumb so they do not have to admint fault?
Hopefully there's an easy fix to this problem.
-Also I did inspect the ribbon before and after the repair. looks new as the OEm
Can anybody help me out with this new problem after replacing the cable -
perhaps you should try a hard reset. Ive had problems in the past where the optical joystick and the illuminators did not work, and that worked for me.
On the other hand, the top illuminators are on the same piece of hardware as the flex cable that was replaced, so a faulty flex cable is possible. The bottom illuminators are on the circuit board that the optical joystick attaches to, separate but connected to the flex cable.
Ive recently replaced my flex cable and touchscreen. The experience i had with the faulty touch screen was that it appeared to receive no power, but was in fact displaying a dark backlit illumination that could only be seen in the dark. At the same time however, the screen did not display anything. I'm not sure if this is similar to your experience, but if so then your touchscreen would need to be replaced.
ive done all repairs on the xperia myself, and one thing ive discovered is if something doesnt work right after a repair, simply disassembling it and reassembling it to make sure all the connections are properly done has worked for me in the past.
"Before the repairs, there would be a flicker of white light and random illuminations. Now there's no lights at all except the power button."
Now when you say the power button, do you mean that a red light appears under it?
I dont know if i can come to a conclusion or that i can help (or have helped) you come to a conclusion, but i can only assure you that the xperia acts out in strange and weird ways.
Good Luck!
Tags
Dismantle / Disassemble Sony Ericson Xperia X1
http://www.ifixit.com/Teardown/Sony-Ericsson-XPERIA-X1/788/1
http://www.formymobile.co.uk/xperiadisassembly.php
http://www.youtube.com/watch?v=AWDurQrRt-Y (REAR)
http://www.youtube.com/watch?v=iyGUbxFqvyc&feature=related (FRONT)
http://www.youtube.com/watch?v=elgC8hwHfYQ&feature=related
For info.
Mike
Thanks for the links. I've tried the hardreset and restoring the original rom but the issue is still there. It's really bugging me that everything works but the LCD screen. I'm currently using MyMobiler to use my phone. The touch screen works fine and so does the soft keys. Just no power for the lights. I might just give up and wait for another phone that catches my eye and then tinker with the xperia myself. but if anyone got a solution or want me to test something then I'll give it a try.
My warranty is no longer affective so I'll use my phone as a tester to help others with any problems.
TRIONDAVE, how's your Xperia running now with the cable mod that you did? Its been 6 months since you created the thread. I hope you're still around.
My Xperia X1 works nearly fine, except for the keyboard issues, so I'm thinking of opening it up. If your Ribbon mod helped I might just do it too once I've got it opened. Mine has a MOUNTain of cracks though, and the battery compartment itself is cracked on both side enough to make the compartment CURVED. Hence the Battery cover doesn't sit well.
I'm looking around for broken Xperias which I might be able to use to change the internal cracked casing. Lets see.
DatDereX1 said:
cool story bro
Click to expand...
Click to collapse
My thoughts exactly.
Hello guys, I am in need of real help over here!
Its just that Ive replaced my ribbon cable, the old one got screwd up.
However I got done for 10 minutes ago, tried to start up the phone.. without success :,(
The ribbon cable doesnt have anything to do with the start up, only the screen am I correct? Cause I cannot even start my phone..
Ive connected the charger, but when I remove the battery it shows a red light, meaning no battery, correct?
So what may the problem be exactly? Maybe the battery is all dead, or?
PLEASE HELP!
for the people with ribbon failures how long have you had the phone before it occurred ? im just interested on the cables lifespan.
mine is fine so far but i have noticed the slider is flimsy and rocks left and right.
Hey guys,
The earpiece speaker on my G1 has developed a fault, the fault being it doesn't appear to work, how easy is it to source a replacement for it and how easy is the repair itself? is there any guides as to how to do it around? (i looked but i couldn't find anything).
I've tried flashing the rom and doing a hard reset but its still faulty.
The loud speakers working fine though so atm all my calls have to be done on the handsfree kit or via loudspeaker which can get annoying.
any help is much appreciated
regards
Streather
Are you using a ROM where sound works?
What ROM are you using?
Tried it with cynagen and the stock tmob one, same results.
Same problem
I'm using CyanogenMod 4.2.5. I dropped the phone about a foot (it fell out of my shirt pocket as I was tying my shoe!), and the earpiece stopped working. Everything else (speaker phone, etc.) works fine.
I've seen a number of similar cases in other forums, so I'm thinking that this is a weak point. I'll attempt disassembly and see if the speaker contacts got moved or something simple. Fortunately, replacement receivers/earpiece/speakers are available over the net.
Meanwhile, I'd love to learn of others' experience with this. The tech manual makes it look like you have to just about completely disassemble the phone to get at the earpiece, even though you can easily access 3 screws on the back of the lcd. Is there a shorter route to the receiver than a complete disassembly?
[update] I found some good info (including a technical manual) by Googling "g1 phone disassembly". And searching for "g1 speaker" on eBay gave some decent looking results.
[update 2] I disassembled my phone, took out the receiver, cleaned its contacts, replaced it, and and reassembled everything. That was a pretty serious chore, and it demonstrated that a nearly complete disassembly is required to access the receiver (yes, including all the stuff at the opposite end of the phone). I don't know how to test the receiver without being in cell range, which my house is not. But at least nearly everything else still works, except the camera--I need to tear back into the phone and make sure I fully seated the FPC. I think finding a replacement receiver will be a challenge--most of what turned up on eBay is actually the main speaker on the back of the phone, and I have yet to find a vendor that sells receivers.
Sadly, you will almost have to tear down the whole unit to get to it. It's not extremly diffucult, but you will need to be steady and gentle. Good luck.
Success!
I haven't seen many report back after tearing apart their phones to address issues with a bad receiver, so here goes. My simple-minded approach of opening it up, cleaning the receiver contacts with a pencil eraser, and ensuring good alignment before reassembling WORKED. I did not have to buy a new receiver.
Now if I can just get my camera to work again (I think I didn't get the cable well seated).
[update]: camera works! Seating that FPC took some nimble fingers--I got it on the 3rd attempt. I hope this proves useful to others who, like me, do not have the warranty option for various reasons.
I dropped my phone once, by accident, same thing happened. The speaker you use to put your ear up to when making a phone call doesn't work, but the speaker phone speaker works as does a bluetooth headset. Called HTC lied said that it just stopped working out of no where, they said its covered under warranty. Luckily the phone is under warranty until March and will be replaced.
I ran into the same problem. I was having intermittent problems with the earpiece. Yesterday I was able to take out the battery and put it in and it started working again. Today that didn't help either. I saw this thread and I thought that I'd try blowing really hard on the earpiece to see if that helps. It seems to be working again! I hope it continues to work.
dirtprof said:
Now if I can just get my camera to work again (I think I didn't get the cable well seated).
[update]: camera works! Seating that FPC took some nimble fingers--I got it on the 3rd attempt. I hope this proves useful to others who, like me, do not have the warranty option for various reasons.
Click to expand...
Click to collapse
Can you post details on how to do this?
My camera stopped working too.
I personally found it easier when disassembling the phone to carefully lift the entire camera and IMEI sticker as a whole unit and remove it as part of the motherboard. That way you dont need to mess with that hard to reach connector. So from where you are at, lift the board back out, reattach the camera assembly, and reassemble as a unit. I think you will find it is MUCH easier
Seat the camera FPC fully
RueTheDay said:
Can you post details on how to do this?
My camera stopped working too.
Click to expand...
Click to collapse
I had to lift the motherboard up and away from the hook that held it down in order for the FPC clip to open fully. Then I inserted the FPC *fully* before closing the FPC clip (my failures resulted from not being able to fully seat the FPC because the FPC clip could not fully open as long as the motherboard was in place). Then the trick was to get the motherboard back under its hook without accidentally pulling the FPC back out again. What I did was to press it gently straight down, using my fingernail to ease it past the hook.
Good luck!
bump...
Yeah looks like all there is on Ebay for speakers is the back one, the one for the receiver earpiece looks like it has two wire connections at each end while the one for the back speaker has them right next to eachother.
So if anybody had this problem, it is very odd and might have to do with the spring connection maybe.
Still I had this problem before and it fixed itself randomly, but this problem came out of nowhere because 12 hours earlier I had dropped my phone on its back and it continued to work fine. Than on my way driving randomly it would not work and I barely set it down in my car.
Once again hopefully somebody has found a part for this because ebay only has back speaker parts.
Best bet is to blow on it and massage it or tap it until it works, damn this sucks because it is basically the very last step to get to after dissambling your phone. So much work to get to such a common problem for many people.
I almost wanted to try to shortcut it and undo the two screws on the screen section to move it around to make connection. Now I am the deusche bag with the bluetooth in his ear all the time.
I almost wanted to try to shortcut it and undo the two screws on the screen section to move it around to make connection.
Click to expand...
Click to collapse
That was what I tried at first. It didn't gain me access to the speaker.
Taking the phone apart is a pain. You really need nimble fingers and faith that you're not breaking the phone when you're levering apart the *very* tightly held together plastic parts. HTC did not make this thing with servicing it in mind. Just be sure to have the right tools (including light and a good magnifying glass if you're over 40) and patience.
Removing the 3 screws that are accessible without disassembling the entire phone will get you in there if you are VERY careful. Unfortunately the one I tried this on did not work differently with a known-good speaker in it. You can delicately dig out the old speaker with a knife (Xacto) and drop the new one in. Takes patients, but not nearly as hard as disassembling the entire phone (been there, done that x10)
I have at least one spare speaker. Maybe more, gotta check my stockpile!
Hey,
My phone got dropped in a rum & coke on Saturday, so i soaked it in 90% rubbing alcohol and let it dry in a rice bath. after 4 days in the rice, it looked dry, so i turned it on. IT WORKS! The screen looks a little trippy (the pattern is even changing throughout the day) but the touch and accelerometer work great. The only real problem is the speakers sound like crap. the receiver is so quiet that it sound like they're wispering, and the back speaker is all crackely.
I found a replacement receiver speaker, but as i haven't taken it apart yet, i was hoping one of you could tell me if this looks correct.
http://www.tvc-mall.com/details/Replacement-Speaker-Earpiece-Receiver-for-HTC-G1-HTCO-G1/photos.htm
If so, i guess i'll order both speakers and attempt to replace them.
That looks about right. Bear in mind, of course, that those pictures are greatly magnified. If you haven't taken apart a G1 yet, you're in for a bit of nerve-wracking prying. Just go slowly and be patient. Getting all the way to the receiver speaker means taking the phone most of the way apart.
Thanks!
I have taken apart a phone before, the Dash (excalibur). I had to replace the screen, it involved removing almost every component.
I think i'll go ahead and order it, and cross my fingers. right now the phone isn't much more then a tiny computer, since i can't hear anyone and i don't have a Bluetooth.
I recently opened up my HD2 - t-mobile to fix the plastic cover on the flashlight. I followed the official HTC video on how to open it and successfully installed the piece. Then I turned it on and found out that the touchscreen didn't function. I had a look inside but that didn't help. I can't send it back to t-mobile because i already opened it which voids the warranty. SOMEBODY PLEASE HELP ME!
Wow...thats...pretty terrible. Make sure that the connector to the touchscreen is firmly seated in it's port and that it's not damaged..and if it is...then consider yourself the lucky new owner of a cracked digitizer! But seriously, if everything LOOKS okay, its probably got a hairline crack, or static has got to it.
Will removing the screen require me to heat my phone and stuff?
I woke up this morning and found that my phone was functioning for a minute then it failed on me.
No, it won't require you to "heat the device" or whatever, and what do you mean it failed on you? It won't do anything now?
Only the touchscreen is malfunctioning so the phone is basically useless.
Hello guys, so my phone fell of my hands yesterday and landed on it's screen. It's cracked but still working, so im waiting for the ebay replacement to arrive. I've already disassembled it, and put it back together, just to see if it was hard. After all that the vibration motor is too loud, i mean, really loud, it was much quieter before.. And the LED Flashlight doesent work, says torch is on but no light.. Could something get damaged or disconnected when i disassembled it? Thank you.
This has many possibilities, and one cannot judge without seeing the actual device. The falling could have damaged it, the dis-assembling maybe .. maybe you stretched, ticked or disconnected something. And I have no knowledge in the device's hardware so I couldn't tell where the issue(s) could be from, and I'm quite sure neither could you. My suggestion is take it a repair shop, let them see what's wrong.
Just my 2 Halalas.
Edit: This thread is now cursed.
Hey guys I'm new here. A few weeks ago i happened to not notice that some liquid spilt on my phone while driving and i left it there like that for a while . then When i got a call and answered couldn't hear the other person. Then i noticed water on the fingerprint scanner as i had a spigen case and it had managed to get into my phone. I turned off my phone immediately and disconnected everything. Next morning i happened to removed the board and dry it out as i have done this many times before when i changed the thermal paste. The water damage indicator was red. After ensuring everything had dried out i put it back together and my phone powered back on and it charges well. But when i go to play an audio file. I get an error Sorry, the player does not support this type of audio file. The audio recorder hangs and i camera app also works but when i switch to video it hangs. Phone has been reset to factory. Same issue. Sorry for the long story. Need some Help on what part to replace. Is it the mic and speaker that's busted or some component like the DAC. If so where is the Dac located and how can i go about fixing this. Any part websites you recommend I'm from India.
Any help is nice guys. Please
My first V20 was one I bought on ebay that had sound not working. Also the camera was not working. I though it would be an easy fix, well, hoped actually, but it was not. I didn't pay much for it so I though it was worth the risk. The problem you have sounds exactly the same. Software reset won't fix it.
I did get it to work though temporarily. I put the motherboard in the oven for 10 minutes. It worked for a few days only.
The problem is that the DAC chip is now faulty due to water damage I'd say. You need a new motherboard. I would suggest buying a new v20 and keep the old one for charging your spare battery on quick charge! Or you can buy a new motherboard only on alliexpress for about 50/60 euros.
Thank you. I did consider an industrial oven. Could you please help me with temps you used? Was it the same error you got while trying to play a track?