I would like to raise the question about the ability of defy to support the above function.
Is it possible for defy to support them?
If not, why they can't be supported?
Due to hardware problem or software problem?
Thx to all of you first
cuz of a locked bootloader if im not wrong.. we cant change kernel
Adding things to kernel is easy: with kernel-modules.
Changing is possible but very hard. (some modules like mmcfix are doing that)
I just saw, that USB-OTG is enabled in our standard kernel-config. EDIT: http://forum.xda-developers.com/showthread.php?t=960633&page=11
And there is a driver for the HDMI-Chip "TDA19989". Does defy have this chip?
I don't know if anyone tried USB or MHL-adapters (i read something about usb-adapters in the past but don't remember where and can't find it again).
Q&A for [USB OTG] [11DEC13] [PATCH] Externally Powered USB OTG
Some developers prefer that questions remain separate from their main development thread to help keep things organized. Placing your question within this thread will increase its chances of being answered by a member of the community or by the developer.
Before posting, please use the forum search and read through the discussion thread for [USB OTG] [11DEC13] [PATCH] Externally Powered USB OTG. If you can't find an answer, post it here, being sure to give as much information as possible (firmware version, steps to reproduce, logcat if available) so that you can get help.
Thanks for understanding and for helping to keep XDA neat and tidy!
Paranoid Android 4.4
Hello!
first of all, thanks for your work. :good:
I would like to try the patch but I don't know which version to choose: I have a Paranoid Android 4.4
Could you help me?
Wifi Crash, Media Crash, Settings "Storage" Crash
Hey guys, I'm on PA 4.6 BETA5, when I flash the aosp or franko kernel (after going back to stock kernel before flashing the new one) my Wifi won't enable, android.something.media crashes and in the settings app, when I tap storage the app crashes...any way to solve this problem or an alternative? Thanks!
PS: I'm really sorry if this was asked before, I read the hole last 10 sites of the forum and didnt found anythings related to my problem, "just" 10 sites because I think its related to 4.4.4 and maybe PA.
Which OTG mod to download for stock 4.4.4?
Which OTG mod to download for stock 4.4.4? There are so many I can not figure out what is the correct one to use.
OTG Android Lollipop
Anything to Android 5.0? I have looking and I think that it isn't incorporate in the stock kernel
thanks
piedra96 said:
Anything to Android 5.0? I have looking and I think that it isn't incorporate in the stock kernel
thanks
---------- Post added at 11:38 AM ---------- Previous post was at 11:34 AM ----------
I have looking and I think that it isn't incorporate in the stock kernel. So, anything to Android 5.0?
thanks
Click to expand...
Click to collapse
There are custom kernels (unleased kernel series, Hells Doctor, Hellscore, ...) which supports OTG and also supports Lolipop.
Stock Lollipop
A zip file where i can make a modification to my stock kernel on the N4! I want to use the stock for a few days to test it!
pm_dsp_ra said:
There are custom kernels (unleased kernel series, Hells Doctor, Hellscore, ...) which supports OTG and also supports Lolipop.
Click to expand...
Click to collapse
mm okey! so, have you test Hells Doctor on Lollipop? I will try out it this afternoon. I'm running a 4.3 stock perfectly with the otg, but Lollipop look like so excited.
Lollipop
Is there a patch for android lollipop for OTG support? I have franco.Kernel installed.
Lollipop
Is there a patch for Lollipop? Or does the kitkat patch work on lollipop?
dangerelvis said:
Is there a patch for Lollipop? Or does the kitkat patch work on lollipop?
Click to expand...
Click to collapse
I have no idea! I have tested Hells Doctor and Hell Core kernels on my Nexus 4 running Stock Lollipop and anyone work. :crying: :crying:
Anyone tried this patch on stock Lollipop kernel? Does it work?
How does one "Simply install the zip in recovery"?
My screen is broken (just the touch; everything is still visible). I was hoping I could install this mod without being able to touch the lower half of my screen so that I could plug in a mouse so that I could copy some files off my device.
I can reboot into recovery mode, but USB debugging is *not* enabled. I've never used "adb" on this device before (I just says "offline" when I try to run it from my PC).
I have no idea how to "install a zip".
Phone is an Nexus 4, running android 4.something.
OTG on Paranoid 4.6 beta 6
Hello,
When I flash the kernel (R199) and the system load I can't turn on the wifi and every time I enter the storege settings they crash.
also tried the other versions of the kernel, no help.
please help.
Thanks,
Is the OP willing to develop the patch for lollipop too? Or is there any nice kernel with USB host support?
nexus 4 lolipop 5.0.1 and xbox wireless gamepad
Hello. I want use xbox360 wireless gamepad on my nexus 4 lolipop 5.0.1. I think first I need kernel with OTG support. What kernel I can download on 5.0.1 android? I need y-cable for receiver of xbox360. what about mouses and keyboards they also need y-cable?
What can be the problem, why OTG still doesn't work
Hey guys,
however I'm completely new to this stuff, I managed to get through every barriers, and I put Cyanogenmod 11 snapshot M12 on my Nexus 4 and after that flashed the suggested kernel and patch successfully to try out OTG. The phone works withput problem, the installations seem to be successful, therefore I tried to connect an external storage to the phone to check if OTG works on it.
For that, I used a SIMPLE OTG cable like this:
<<<LINK CANNOT BE SHOWN SINCE I AM NEW TO THE FORUM - picture is the second picture of the first post in this thread>>>
connected to an Y-cable SIMILAR to this:
<<<NO LINK AGAIN - the 3rd picture of the first post in this thread>>>
The difference from the one on the picture is that mine has a male mini USB end instead of a female normal USB end as in the picture. My cable is the cable of an external wichester otherwise.
So, I tried with this cable setup, the result was that both the phone and the connected storage received electricity from the external power source, but the storage was not detected by the phone. I had a feeling that it doesn't get enogh power, so I attached it to a USB phone charger just to be sure, but the situation remained the same: the light on the storage was green, which means it is charging, the light on the phone was also on, but the storage was not detected.
My question is if I should try with the exact same cable set that can be found in the first post of this thread on the first picture or mine also should do the job, and there should be still some software related problem?
Please also tell me if you need more information on this to answer it, however I tried to be specific.
Thank you for your help in advance.
Hello. What i can do on lolipop? There is no solution? I have a 32gb flash drive, y-otg cable, standart power adapter micro-usb-male. Rooted nexus4
Which zip I need to download?
Hi, i'm really beggining on Android stuffs, since I didnt had one until the last week, so I'm really in doubt about which one of the zip files i need to install in my system to make the OTG cable work properly.
Once I downloaded a random ziddley zip on the internet and when I installed it in recovery mode, i needed to reinstall the android system on my phone, since the phone wont boot anymore.
So, can anyone help me? I'm sharing in this post a screenshot of the Android Version screen on the settings. I've rooted my phone using the King Root app
Considering that my android version is 4.4.4, I consider that I may download one of the following:
4.4.x: 2013.12.11 1604ET: [fk r199] [fk r199-CM]
4.4.x: 2013.12.06 1445ET: [aosp r7]
But which one?
And just another noob question. Is this the right way to install the ziddley zip on my phone?
(www).addictivetips.com/mobile/how-to-install-a-rom-or-app-from-zip-file-to-android-device-from-recovery/
Sorry for the noob questions and thanks to anyone who helps, because I REALLY need the otg cable to work, so I can develop some things using the XBOX 360 cable!
Removed
Figured this would be the best place to ask, discus or what ever else takes the fancy but I was floating the internet the other day looking up about USB OTG for my T230NU and found this...
A bit of googling didnt seem to pull up the CPU that the Brazilian "NT" varient uses... but what I am thinking is if it uses the same Marvell SoC as the T230 / T230NU would that be something that could be ported?
I Did do a quick forum search before typing this and nothing came up and thought it of potential interest
Anybody looking into this? OTG would be nice. Hate not being able to mount usb storage properly as well.
mkhtfld76 said:
Anybody looking into this? OTG would be nice. Hate not being able to mount usb storage properly as well.
Click to expand...
Click to collapse
OTG support is not available on marvell variants. I don't know if the same holds tru for the sm-t237p which is a qualcomm/msm device
like the tab 4 10.1 and the tab 4 8.0
The same lack of OTG support occurs in the tab 3 line for the 7.0 models, again, marvell.
While the code is present in the kernel source, the actual required hardware components are not present on the board.
So the answer is no.
m
Edit- i do have a question about mounting the tab as usb-storage in recovery, either philz or twrp, does that work ?
Hey everyone!
I'm running the Nexus Player with the 3.10.20-g43ab991 kernel and Android 7.1.1. I've bought a Micro USB to LAN adapter and it has the RD9700 chipset which is sadly not supported by default. However, I've found this post and they made a driver - unfortunately, for a very old kernel version.
Has someone this driver for newer kernels or could compile it for new kernels (unfortunately, I'm a total noob at this)?
Thanks!
I have no experience with that particular product but I can tell you that the TP-Link UE330 works with an OTG adapter cable.
Some times ago,developers find a way to activate otg feature on marshmallow but that way doesn't work on nougat.dears please help to solve this problem and active otg on nougat.
I was about to post this. I also want to know if there is any progress on OTG for Nougat?
Even I corrected the target of plugusb file in «otg on» file,but it doesn't work.
Where is all devolpers ?
Hi.
I've just tested my Chord Mojo with MM OTG and the sound is full of pops and ticks. I then tested it on my 2013 Moto X and the sound was fine, so even with the kernel mod OTG is not as it should be on our P9 Lite.
I think I will flash Nougat and then look for a new phone that can do OTG natively.
Shame as I think the P9 Lite is a great phone and I got it for a steal as well.
So its back to the drawing board.