(Edit 1) Found a fix already! Read post 2!!!
Hello there,
I've been having a OnePlus Two since 4 months already, and had like 2 or 3 home button not working issues.
They used to fixed by themselves after a couple of days of not working, but not this last time.
I tried already the reinstalling system (after formatting system via TWRP), clean it several times, hard reset (hold power button for more than 20 seconds), complete drain battery and fully charge it again, force stop fingerprint service, take out the tempered glass screen protector, and none of those solutions worked.
I here attach (copy the link, can't upload a video directly to this post) a video in which you can see that whenever I power on the screen (still locked), the home button works for several times, but as soon as I unlock it (pattern lock) it stops working. This makes me think that the problem is software, not hardware, but as I said before, already tried reinstalling OOS 3.0, wiping system, cache, data, internal storage, etc.
I compressed the video so it wouldnt be too big, but quality is good enough, just rise the volume so you can listen to the "vibration" that the home button produce.
Any help would be appreciated.
Sincerely,
Daniel Castro
Fix for the issue!
Forum people, I found a fix!
Ok, the solution for making the home button work again (with fingerprint sensor) is the following.
-Factory reset while in OOS 3.0
-Set up everything up and then reboot into fastboot mode
-Install OOS 2.1 via fastboot (you will need to search the forums for it)
-Set up everything up and try to set up fingerprint (it wont work)
-Copy OOS 3.0 (Beta) in the root of the phone
-Reboot into stock recovery and flash OOS 3.0 (beta)
-Factory reset it and set up everything again
-Voila!
Feel free to try this method and reply to this threat or P.M. me for any help.
Sincerely,
Daniel Castro
I have the same problem
Tomorrow i'll try your method
I've posted a questione about this issue,
I think the One plus team should find a solution to this problem that afflict many users
Also, don't forget to rotate your phone 720 degrees, counter clock wise! ? hocus pocus....
DCastro555 said:
Forum people, I found a fix!
Ok, the solution for making the home button work again (with fingerprint sensor) is the following.
-Factory reset while in OOS 3.0
-Set up everything up and then reboot into fastboot mode
-Install OOS 2.1 via fastboot (you will need to search the forums for it)
-Set up everything up and try to set up fingerprint (it wont work)
-Copy OOS 3.0 (Beta) in the root of the phone
-Reboot into stock recovery and flash OOS 3.0 (beta)
-Factory reset it and set up everything again
-Voila!
Feel free to try this method and reply to this threat or P.M. me for any help.
Sincerely,
Daniel Castro
Click to expand...
Click to collapse
Will it erase my internal storage during that fast boot step? So I can backup all my data.
Sent from my ONE A2003 using Tapatalk
these fixes are all coincidences... we need to request a definitive fix from One plus team if is a software issue.
LOL9988 said:
Will it erase my internal storage during that fast boot step? So I can backup all my data.
Sent from my ONE A2003 using Tapatalk
Click to expand...
Click to collapse
It will erase everything, make a backup before starting the process.
faustin95 said:
these fixes are all coincidences... we need to request a definitive fix from One plus team if is a software issue.
Click to expand...
Click to collapse
Most probably hardware design fault, solution would be to redesign the phone and release a fixed design, will probably not happen unless oneplus3 is the solution.
And I second that it's just coincident behind these back and forth flashing of firmwares "solving" it, almost religious. But what are people to do when oneplus is not a company that takes responsibility for they're mistakes.
pitrus- said:
Most probably hardware design fault, solution would be to redesign the phone and release a fixed design, will probably not happen unless oneplus3 is the solution.
And I second that it's just coincident behind these back and forth flashing of firmwares "solving" it, almost religious. But what are people to do when oneplus is not a company that takes responsibility for they're mistakes.
Click to expand...
Click to collapse
If it works, its worth a try . And yeah, but we are not in any OnePlus Forum, neither debating about if they are gonna do anything about their own issue, we are trying to fix what an irresponsable company wont.
can we make together an official request to one plus to give us an answer or explanation about this? a lot of users are facing this issue, it's not normal
This is my second opt I bought that this problem has happened
sorry for my english
I had also tried lot of things but home button is not responsive at all.. H2os,exodus,oxygen 2.1 ,3.0 same everywhere
---------- Post added at 04:01 AM ---------- Previous post was at 03:59 AM ----------
Error is: when i open fingerprint setting
Enrollment not working try differnt finger or try again ... Nd fingerprint autotest not starting also
i've turned to stock i've updated to oxygen 3.0 bet and the button worked again
i think rooting installing twrp and installing different roms may be the cause of this issue
faustin95 said:
i think rooting installing twrp and installing different roms may be the cause of this issue
Click to expand...
Click to collapse
Unfortunately that is not the case, it's a hardware design bug.
However you can f-k up your finger scanner by damage your persistant-partition if you flash up and down between different ROM/bootloader revisions. But it's easily fixed by flashing the image file for that partition again.
pitrus- said:
Unfortunately that is not the case, it's a hardware design bug.
Click to expand...
Click to collapse
it's a driver issue
faustin95 said:
it's a driver issue
Click to expand...
Click to collapse
50/50 moisture sensitivity and driver issue.
Home button has been working fine for a year, installed 3.0.1 today and suddenly home button only works in OOS 3.0.1. No longer works in CM 13, yet works fine in OOS 3.0.1. Definitely a driver issue.
Tried installing OOS 2.2.1, wiping, then installing Grarak's CM 13 and home button refuses to work. Wiped system, data, cache, installed OOS 3.0.1 and home button works again. Tried wiping again and installed CM 13, home button stopped working. Wiped and reinstalled OOS 3.0.1, home button works again.
Odd thing, my phone will only work with CM13 roms and OOS 2.2.0 or less for fps and home button. Nothing will fix or ever work.
For me, the home button stopped working for a short while on Graraks, then it just jumped back to life again and I haven't had any more home button blackouts after that. If it's a driver issue, it's an extremely intermittent one.
The fingerprint scanner has stopped working from time to time at lockscreen, but this is acceptable for an official hackjobb supported scanner until official sources are released ?
Need Help with this!
Hi everyone!
I have a OP 2 for more than one and a half years now and never had any issues with it(stayed stock...) until recently. I didnt update the phone to the latest version and was putting it off, and today in the afternoon when I tried to unlock my phone it said the 'Fingerprint hardware is not available' and after unlocking the phone with the pattern, it IMMEDIATELY LOCKS ITSELF BACK !!! after split second it just locks the screen while everything is working like connection, wifi, messages, notifications, etc. but due to this I cannot access anything on the phone, can't go to settings and switch to onscreen nav bar buttons, can't force stop/wipe cache the com.fingerprints.serviceext either, tried restarting it several times, downloaded the update but can't even install it because the phone just locks! I have no idea what would fix it and I am avoiding a full reset and wipe on the phone(also based on all i have read, dont think it would fix it anyways)
If anyone knows whats the problem or has dealt with it or knows someone who has, please help me out here on how to fix this and what to do. I did not root it or flash custom ROM's on it yet so literally dont know why it happened.
Thanks,
Max
Related
As a noob, I could not post this in the thread where it applied. I hope someone sees it and passes it along.
Problem: the tab does not automatically rotate the screen image when you rotate the orientation of the device. The lock switch is "unlocked". The problem arose after the ICS update was applied.
I found this link in another device forum that seems to be dealing with the same issue.
http://forum.xda-developers.com/showthread.php?t=1592170#
Basically, he replaced the accelerometor sensor driver files I think.
Hopefully one of the developers here will see this and can hookup with the other author to see what is really going on finally.
Until then, we need to keep a safety pin handy to hard reset the A500 when it goes insane.
the_cryptonym said:
As a noob, I could not post this in the thread where it applied. I hope someone sees it and passes it along.
Problem: the tab does not automatically rotate the screen image when you rotate the orientation of the device. The lock switch is "unlocked". The problem arose after the ICS update was applied.
I found this link in another device forum that seems to be dealing with the same issue.
http://forum.xda-developers.com/showthread.php?t=1592170#
Basically, he replaced the accelerometor sensor driver files I think.
Hopefully one of the developers here will see this and can hookup with the other author to see what is really going on finally.
Until then, we need to keep a safety pin handy to hard reset the A500 when it goes insane.
Click to expand...
Click to collapse
Clean boot your tab. This will force the OS to install itself again.
Note: Clean boot will erase all the data/information which is saved on your tablet. Recommend you to back up the data before performing a clean boot.
1. Shutdown the tablet
2. Press and hold volume up key (the key next to rotation lock) until you finish step 4.
3. Press power button for 3 seconds until you feel device vibrates then release power button.
4. Once you feel device vibrates, very quick to switch on/off "rotation key" many times (this activity has to be done very fast, otherwise it will not succeed). To ensure you succeed, switch on/off rotation key when Acer logo appears on screen.
5. Wait for a while (you will see Erase Userdata and Erase Cache on top-left corner on screen), device will reboot and start from OOBE screen.
See if that fixes it.
Didn't work for me had to factory reset tab to get accelometer working again. This is the second time.
Sent from my PC36100 using XDA
Erasing as suggested did not help. Only thing found to help so far has been the pinhole hard reset. And, even that did not work once I flashed to "Acer_AV041_A500_1.041.00_WW_CUS1" version. I reverted back to what Acer had pushed to me, and it is working as well as before, meaning, it works as long as you have a pin ready to stick in it.
I have something to add to this thread. The auto-rotation issue started for me after switching to the V3 ICS bootloader.
I kind of found a workaround for it. (If you can call it that)
If I start or reboot my tablet in portrait mode. Auto-rotate works
If I start or reboot my tablet in landscape mode. Auto-rotate does not work.
This happens each and every time. It happens on Civato's new FlexReaper ROM & with Smaury's Lightspeed ROM.
Moscow? Thoughts?
Apparently how I finally solved this problem is by flashing the custom ICS bootloader V4 (read: V4 ONLY). Had tried V3, V6 and it doesn't work.
Had tried both custom ROM and stock ROM the problem will still persists with the said bootloader. But once on V4, it just works like a charm.
I have the same issue with the ratation.
Did anyone try http://forum.xda-developers.com/showthread.php?t=1592170# ??
Let me know please
qpmzal said:
Apparently how I finally solved this problem is by flashing the custom ICS bootloader V4 (read: V4 ONLY). Had tried V3, V6 and it doesn't work.
Had tried both custom ROM and stock ROM the problem will still persists with the said bootloader. But once on V4, it just works like a charm.
Click to expand...
Click to collapse
How do I flash custom ICS bootloader V4? Where is it available? And can it be flashed on top of a stock Acer ICS ROM?
FWIW, although I LOVE having Android tablets, issues like this drive me away from Android phones as I can't deal with this sort of bugginess on my daily use phone.
Ahhh, my other half has just phoned me about this, seems it started doing it after she dropped the tablet, I put the ICS update on it the other week, be nice if its a simple fix instead of a me having to take it to bits and repairs it fix..
Although I could give her my Xoom and then use that as an excuse to get myself something new
auto rotat pro
dude plz helppp......................I have to keep auto rotate off.:crying:
It will rotate Landscape, but won't return to portrait.
It wil flip Landscape on one side and Landscapeon the other side, but won't do portrait, till auto rotate is turned off.
Anybody have any suggestions on how to fix this?
I guess I could whack it and start over, but that blows! That would at least tell me something I guess.
It's really irritating. And I dont wat to do......helpppppppppppp:crying::crying::crying:
Installation
https://github.com/LegacyHuawei/local_manifests/wiki/Installation
Bugs
https://github.com/LegacyHuawei/local_manifests/wiki/Status
Downloads
https://basketbuild.com/devs/LegacyHuawei
Changelog
https://github.com/LegacyHuawei/local_manifests/wiki/CM11.0-changelog
If you have any bugs to report, open new issue at https://github.com/LegacyHuawei/local_manifests/issues
Readme
Use the standard Torch app wherever possible, it only enables flashlight. Other apps from Play Store are designed to use the camera interface, which means camera will use additional power.
For more RAM: Settings->Performance->Memory management.
Do not enable KSM, as video encoder/decoder stops working.
HuaweiSettings
Charge current - allows you to set custom charging current. While this actually limits the current input, it effectively decreases or increases the available current transferred to the battery. This is useful in multiple ways:
Slower, but more effective charging. Your battery will last longer.
Faster charging when connected to USB. For example, USB charging is limited to 500mA, but newer PCs allow drawing up to 800mA or even more. This can be configured via the setting.
Manual override of non-standard charger allowing to draw more than 500mA.
Magnetic sensor calibration - lets you delete previous calibration information. This is useful to recalibrate the compass (when it's inaccurate). Just tap the item & then open any compass up to recalibrate your sensor.
If the phone reboots unexpectedly, crash log is found at /data/dontpanic .
To report bugs, use this app: https://play.google.com/store/apps/details?id=com.tortel.syslog
Thank you, i'll try
wow, downloaded...
Many thanks, good job!
after installing cm11 and gapps, the phone always reboot to recovery
ggunzio said:
after installing cm11 and gapps, the phone always reboot to recovery
Click to expand...
Click to collapse
Did you do a factory reset before?
And does it show the cm logo or just boot to recovery?
Sent from my IDEOS X5 using Tapatalk
Blefish said:
Did you do a factory reset before?
And does it show the cm logo or just boot to recovery?
Sent from my IDEOS X5 using Tapatalk
Click to expand...
Click to collapse
before installing the rom, i've wiped everything, data, cache, system and dalvkit cache, reboot recovery. After installed the rom, and right after, installed the gapps. Then, in recovery, reboot system and after it show the huawei logo, it enters recovery without showing the CM logo.
EDIT: i will install ble_part stock, and them install again the B518, repartition again and try to install CM again.
Booted and installed just fine after doing Blepart and using your recovery. It's slow as molasses, probably in great part due to the fact that the display glitches are still there, but it certainly works, and it's as much KitKat as my Moto G. Something worth mentioning, your recovery has some sort (the same?) of display glitch as well in which the screen only seems to update after a couple of presses of the volume button, not immediately.
ROM and GAPPS, everything works fine.
No glitches for me.
Great job, thanks!
faekplastik3s said:
Booted and installed just fine after doing Blepart and using your recovery. It's slow as molasses, probably in great part due to the fact that the display glitches are still there, but it certainly works, and it's as much KitKat as my Moto G. Something worth mentioning, your recovery has some sort (the same?) of display glitch as well in which the screen only seems to update after a couple of presses of the volume button, not immediately.
Click to expand...
Click to collapse
Thanks.
I don't have any devices to compare it with so it feels "fast" to me. Its great to know the recovery suffers same display bugs, it confirms that its in fact kernel side problem. Though, kernel side does not have BLT enabled, which I thought would be the problem. I'll debug the registers, and see if I can find something odd. It could also be a clock hz issue, it was changed in 3.4.
Sent from my IDEOS X5 using Tapatalk
Blefish said:
Thanks.
I don't have any devices to compare it with so it feels "fast" to me. Its great to know the recovery suffers same display bugs, it confirms that its in fact kernel side problem. Though, kernel side does not have BLT enabled, which I thought would be the problem. I'll debug the registers, and see if I can find something odd. It could also be a clock hz issue, it was changed in 3.4.
Sent from my IDEOS X5 using Tapatalk
Click to expand...
Click to collapse
Well, it stutters a lot, and it's not nearly as smooth as something like Aurora or even stock Huawei ROMs, but I'm sure it's related to the display issues or another issue like that because even scrolling through the Settings app or the little animation in the notification drawer that flips into the shortcuts stutters like hell and drags around, which shouldn't be an issue for this device and wasn't a problem with other ROMs, and overclocking and other user-level optimizations do nothing to alleviate it.
I did also notice black screens when waking the device from lockscreen (digitizer still works) almost every time, requiring multiple attempts until the display finally wakes. I know you squashed this one multiple times, but here it is again.
It's a miracle for this to happen to begin with, so I can't help to be amazed seeing KitKat on this device. Thank YOU so much, Blefish.
do i need to have my phone rooted?
faekplastik3s said:
It's a miracle for this to happen to begin with, so I can't help to be amazed seeing KitKat on this device. Thank YOU so much, Blefish.
Click to expand...
Click to collapse
This. If some months ago anyone told me I'd be installing 4.4 on this device I'd tell them they were crazy.
Thanks for your amazing work, Blefish
Here its works as it should be, you are awesome blefish
Sent from my SM-T210 with rocketTab 2.1 + MK1 kernel using tapatalk v4
Finally i could get it to boot.
probably i broke something, i've installed the oficial rom and then, with 5.5.0.4 recovery wiped everything. Next installed the blepart, new recovery and its working
Good job sir
Thank you!
faekplastik3s said:
I did also notice black screens when waking the device from lockscreen (digitizer still works) almost every time, requiring multiple attempts until the display finally wakes. I know you squashed this one multiple times, but here it is again.
Click to expand...
Click to collapse
Yes, I have waking problems too.
Install everything (partition, 6 recovery, cm11 rom and gapps) and works pretty well so far.
Fantastico. :good::highfive:
lemene said:
Install everything (partition, 6 recovery, cm11 rom and gapps) and works pretty well so far.
Fantastico. :good::highfive:
Click to expand...
Click to collapse
is anyone having problems to connect to wifi networks? i cant connect
EDIT: i guess that is a problem with the wireless definition of the rom, im thinking this, because i can connect to open networks, but when i change the segurity of the wlan to wpa or wpa2, i can't connect to it.
Could you look at this @Blefish?
Im not sure if its a bug or not, maybe something is broken in wpa.supplicant
[]
I have flashed BlePart recovery, i have rebooted the recovery and i have flashed blepart 2.2 then i have flashed CVM Version 6.0.4.6. The phone rebooted and now i cant open the phone or recovery. I tried to install offical 2.3 from sd card but i coudn't. How can i recover my phone?
So I've been searching all the internet regarding my problem and found none to have my problem.
I was using popwiz rom and after a while my fingerprint sensor stopped working with the error "An error has occureed with the fingerprint sensor. If this message appears repeatedly, restart your device."
Because I needed my G900FQ, I ignored the issue for a while. Found S7 insanity which has a fingerprint bug and forgot about the problem.
Yesterday wanted to check out official MM for my S5, and had to reflash stock lollipop. Then I remembered my fingerprint problem so I tried to set it up. I kept getting that nasty error, tried deleting cache, tried deleting data with Titanium. Reflashed stock 2 times again, nothing worked. Until I was ready to give up and go to bed. Then it suddenly started working. Managed to set it up and activate fingerprint unlock.
Now is the bummer!
I CAN UNLOCK with fingerprint if waiting about 3 seconds after turning screen on.
I CANNOT ADD FINGER through settings, I get the nasty error message.
Tried to enter factory tests and under NormalScan button says Version 0.0.0.0 and in SensorInfo says Ready and stays that way.
I tried to enter factory tests very fast after unlocking with fingerprint and I got, only once and for a brief moment, the right Version and SensorInfo, and Normal Scan showed data and graph.
Now I will try to install official MM firmware with Odin.
Anyone has any ideas to what the cause may be ? And maybe a solution ?
Thanks in advance
L.E. I installed official MM firmware and now fingerprint sensor works when unlocking and adding fingers, but when I try to unlock my phone while it is connected to a power source I get the nasty error message again and prompts me for my backup password. Any advice would be deeply appreciated.
Flash a stock ROM and factory reset?
It seems you did not read the whole thread before suggesting me this...
I did that many times. Lollipop and MM official stock... Its like the sensor is not responding in some situations , but in other situations it does. And this seems to be pretty random..
*Detection* said:
Flash a stock ROM and factory reset?
Click to expand...
Click to collapse
laurent.siku said:
It seems you did not read the whole thread before suggesting me this...
I did that many times. Lollipop and MM official stock... Its like the sensor is not responding in some situations , but in other situations it does. And this seems to be pretty random..
Click to expand...
Click to collapse
It seems you don't even know what you typed, nowhere in your OP did you mention factory resetting and then flashing a stock ROM
Only that you flashed stock ROMs, flashing stock ROMs does nothing to reset anything and will leave behind bugs from the previous ROM if the issue is with an app / data etc
Before getting clever, read what you type
It's obvious that by flashing a stock rom over a custom one will leave bugs. Did full wipe (system, data, cache&dalvik, even phone internal sd) before flashing stock, every time. Thanks anyway..
*Detection* said:
It seems you don't even know what you typed, nowhere in your OP did you mention factory resetting and then flashing a stock ROM
Only that you flashed stock ROMs, flashing stock ROMs does nothing to reset anything and will leave behind bugs from the previous ROM if the issue is with an app / data etc
Before getting clever, read what you type
Click to expand...
Click to collapse
Well maybe next time add that fairly important info to your main post, instead of hoping everyone is psychic, and then throwing a hissy fit when they suggest something you have not stated you already tried.
So, it just popped up while my phone was idle, without anyone calling it in here first, YotaPhone finally decided to give us EU users the RU124 firmware! It looks from the changelog to be the exact EU equivalent to its RU counterpart, including YotaTravel, the return of the YotaStore and other stuff. It's been so long that I don't even remember, but I should be fine flashing this and then reflashing SuperSU and Xposed without losing anything, correct?
If you have stock recovery it will install fine. If not you should be able to grab the update zip from /cache and side load. Then reflash what you want.
Sent from my iPhone using Tapatalk
Yep I'm still on the stock recovery (I just boot TWRP every time I need it). Gotcha, then I'm just dumping my Titanium Backup folder onto my PC as a precaution, and then I'll update and report back on SU\Xposed.
Looks like whatever Yota pushed at 117MB was the wrong thing - a failed update attempt and a reboot later, it's now 0.94 GB. Seems like it's the correct size in ftp://fw.ydevices.com/YotaPhone2/Firmwares/EU/ so now it should work.
Update from RU1.1.112 to RU1.1.124 issue
https://r.tapatalk.com/shareLink?ur...share_tid=3436224&share_fid=3793&share_type=t
Sent from my iPhone using Tapatalk
Just as expected the 0.94 GB update file worked, I reflashed SuperSU and Xposed and the phone is working great on 1.124b.
What version were you coming from?
Sent from my iPhone using Tapatalk
EU1.87. I wanted to go to the RU version but never could get a KitKat RU firmware to boot on my device, so I just gave up and went back to the latest EU firmware.
Ah OK that makes sense. Glad you got it working.
Sent from my iPhone using Tapatalk
Go mine today (1.1.44HK)
Updated to EU 1.1.124b with official yotaflasher.
No Su nor any hack.
So far no bug, it's a great device.
Hi there!
I'm waiting for my yotaphone 2 from this new wave from chinese shops. I ordered the International version. Is it safe to flash the EU version firmware over the "international" version?
And please, can anyone provide an alternative downolad link for the yota flasher?
The one from offcial website:
https://yotaphone.com/us-en/ypflasher/
is a corrupted zip file.
Thanks!
Edit:
I could get it from here:
ftp://fw.ydevices.com/YotaPhone2/YotaPhoneFlasher/
Seems there's a bug.
Almost each time i try to unlock phone (with power button) from EDP the pin keyboard isn't showing up, i must tap all over the EDP screen, way it's relocking then i can have the keyboard again.
Solved by using gesture instead of pincode
satsuki_yatoshi said:
Solved by using gesture instead of pincode
Click to expand...
Click to collapse
Gutted they removed the Instagram Cover instead of fixing it!
Rarelyamson said:
Gutted they removed the Instagram Cover instead of fixing it!
Click to expand...
Click to collapse
they removed the Instagram Cover instead of fixing it!
Click to expand...
Click to collapse
Instagram restricted access to its API, so none of 3rd party apps now work properly. Thats why Instagram Cover was removed.
Hello
I deployed this great update a few days ago, and it clearly brings numerous improvements and fixes.
One visibly new bug annoys me a lot anyway, and that's why I am posting :
When I type a SMS on the EPD, lots of freezes occur. And today, I found a simple pattern. I type a word, and then I back-delete one or a few letters of it. Then I add new letters, and that frequently freezes the EPD for a long moment.
It's not 100%, lots of times it freezes under these conditions, few other times it does not.
I setup 3 languages to choose from (thanks to the update !) and the auto correction is ON.
Does someone else experience the same issue ? Any workaround or fix ?
Thanks
Appens to me 2 times, each time i needed to look/unlook the edp screen to solve
My problem is that with the latest update I need to restart my phone until it starts charging. Otherwise it will not charge ... does this happen to anybody else? Probably I should try to reset ...
no charge bug here
No charge bug here neither. Quite the opposite in fact, I would even say that autonomy obviously improved since this update.
And I confirm I have the same bug with the PIN keyboard not showing up on the EPD when using the Powa button. It happens very often after using the other screen, but unlocking by tapping twice is an easy and efficient workaround.
Surprising obvious bugs anyway, I hope the Yotagods watch us and intend to fix them.
Hey guys!
In the last week my wifi&BT stopped working suddenly, without any software change or new app installed. e.g. (when I swipe wifi, it looks like it is working, but cannot find any network)
mobile data still functions.
After reading quite a lot of manuals, I understood it might be a hardware malfunction, However, I tried to do few things already to understand if there might be another reason, none of the below worked
-Play with aeroplane mode and wifi.
-wifi fix applications
-Factory data reset.
-Wipe the phone and flash oxygen 3.1.0 via TWRP.
Before giving up, Wanted to ask if you have any advice that might help:
Any customized room that might will work?
Any way to check the phone log to understand what happens when we do it?
Any general advice?
Thanks in advance!
E.
try this rom
follow the guide completely
http://forum.xda-developers.com/oneplus-2/general/rom-hydrogenos-v1-2-0-sensors-t3264711
araaraara123 said:
Hey guys!
In the last week my wifi&BT stopped working suddenly, without any software change or new app installed. e.g. (when I swipe wifi, it looks like it is working, but cannot find any network)
mobile data still functions.
After reading quite a lot of manuals, I understood it might be a hardware malfunction, However, I tried to do few things already to understand if there might be another reason, none of the below worked
-Play with aeroplane mode and wifi.
-wifi fix applications
-Factory data reset.
-Wipe the phone and flash oxygen 3.1.0 via TWRP.
Before giving up, Wanted to ask if you have any advice that might help:
Any customized room that might will work?
Any way to check the phone log to understand what happens when we do it?
Any general advice?
Thanks in advance!
E.
Click to expand...
Click to collapse
Earlier today, my fingerprint sensor/home button completely stopped working.
I tried restarting, wiping cache and dalvik cache, re-installing the ROM, and I even went back to OOS and H2OS (both stock ROMs) to see if it would work. Alas, nothing worked.
A friend of mine then called me. I told him my home button is dead. He told me it happened to him once, and all he had to do was force restart the phone and it worked again.
I'll suggest that you try the same.
Hold the power button for ten seconds while your phone is on and it'll force restart.
Hope this fixes your problems, mate!