I have 2 samsung s4 sgh-i337 at&t phones and the both lock up when trying to enter stock recovery... i guess the custom recovery didn't load... i get this : odin mode(in red),product name : sgh-i337(in white), current binary : Samsung Official (in white), system status: custom (rooted, in white), knox kernal lock: 0x0 (in white), knox warranty: 0x0 (in white), csb-config-lsb: 0x30 (in white), secure download: enable (in blue), write protection: enable (in grey), emac burst mode : enabled (in grey) ..... there is a android pictured in the middle... it says:" downloding... do not turn off target!! Thats where it freezes up...
I can do the down vol, menu and power button to undo it... but i still have no way into recovery(odin)
Any help..?
If you have a locked bootloader, you can't load twrp, only safestrap.
It may not be frozen, the phone is in download mode and stays on that screen when flashing a file to the phone with Odin.
So....
audit13 said:
If you have a locked bootloader, you can't load twrp, only safestrap.
It may not be frozen, the phone is in download mode and stays on that screen when flashing a file to the phone with Odin.
Click to expand...
Click to collapse
So,... I just put the phone on that screen and use Odin to start a new rom to install..? I'm not really sure how to use Odin...
It depends on which rom was on the phone before you flashed th custom recovery.
I would start here: http://forum.xda-developers.com/galaxy-s4-att/general/guide-odin-to-stock-updating-rooting-t2926642
Related
hi there im new to these forums and have serched everwhere for a solutuion but i cant find one anywhere. I recently tried to put a custom rom on, but now when i try to turn my phone on it says: Firmware upgrade encountered an issue. Please select recovery ode in kies & try again. Kies wont reconise my device as it wont fully turn on and when i try flash the stock firmware to my device using odin, on the download screen on my phone it doesnt download it from odin it has this on the screen under download mode:
ODIN MODE
PRODUCT NAME: GT-I9505
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0X0
KNOX WARRANTY VOID: 0X1
CSB-CONFIG-LSB: 0X30
WRITE PROTECTION: ENABLED
eMMC BURST MODE enabled
Please help?!
- Download and install this drivers -> HERE
- Put ur phone in DOWNLOAD MODE (how u had it before)
- Install ODIN in ur pc -> How to
- Flash ur STOCK FIRMWARE (it comes with .zip file, u have to unzip it and use only the .tar file)
- Enjoy ur phone again
Dear XDA User,
I get bootloop after flashing stock firmware via ODIN, from Thread [GUIDE] Unroot/Unbrick, Flash stock Firmware i9505 I've try many way, but my i9505 still bootlop after Samsung Logo and vibrate.
I can't enter recovery mode, but when I enter Downloading Mode, here the status:
ODIN MODE
PRODUCT NAME: GT-I9505
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
KNOX KERNEL LOCK: 0x0
KNOX WARANTY VOID: 0x1
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enable
eMMC BURST MODE enabled
I've try ODIN with PIT File to, but still get bootloop, Please help me, this is my only cellular phone.
* Sorry for my bad English
Did you do a factory reset in recovery?
GDReaper said:
Did you do a factory reset in recovery?
Click to expand...
Click to collapse
I can't enter Recovery mode, it's always bootloop, after flash custom recovery like TWRP, it's still same, just Downloading mode that I can enter...
Open Odin, uncheck everything except f reset time, flash rom, when you see the reset in the status window, remove USB cable from the phone, remove battery, replace battery, use buttons to boot into recovery (power, home, volume up) wipe, and reboot.
Please Help me I don't Know the right FIRMWARE For this device. Here's an Information that I saw in my device. I'm really Confused what ROM to download. I used Safestrap App and Wipe My Device and It turns out Stuck at Samsung Logo with a picture of Padlock (that is Unlocked) and below the padlock it says "Custom". All I Can do is to go to DOWNLOAD MODE. I hope someone can Help or Give me Information. TIA
1.) When I try to update the software, my screen goes to AT&T Update screen, So I think it's an AT&T Device.
2.) When I go to DOWNLOAD MODE, Here's what I see:
Odin Mode.
SGH-I337
Binary: Samsung Official
System Status: Custom
Knox Kernel Lock: 0x0
Knox Warranty Void: 0x0
CSB-Config-LSB: 0x30
Write protection: enable
eMMC burst mode enabled
3.) Please See these Attachment Pictures (I use Sammobile App to Identify my device Info.)
Your device is what download mode says.
The pad lock screen is only on the AT&T s4 which is the sgh-i337. The phone has a locked bootloader and can only run custom ROMs that can be flashed using safestrap. You will need to re-flash the stock firmware.
This may help: https://forum.xda-developers.com/ga...-to-update-to-i337oc3-5-0-1-keeproot-t3075814
Hi all,
Please bear with me, I'm in way over my head here and don't understand most of what I've done. I was experimenting when I probably shouldn't have been.
So, I installed DarkLord's Note 7 kernel and rom. I found it to be quite buggy and am now wanting to wipe my phone and install Phronesis-N9005-N7-v6.0.
Problem is, when trying to boot into TWRP, I'm met with the the following:
ODIN MODE
Product name: SM-N9005
Current binary: Custom
System status: Official
Reactivation lock(kk): Off
Knox Kernel lock: 0x0
Knox warranty void: 0x1
Qualcomm secureboot: Enable (csb)
Rp swrev: S2, T2, R2, A3, P3
Write protection: Enable
UDC start
Downloading...
Do not turn off target
I've had it on for hours and it didn't do anything.
I managed to reboot it and it ran as it did before, in Darklords rom.
I read I have to install the official firmware and install it via Odin but I can't find anything about my device. On the back of it, it says:
SM N9005
FCC ID - A3LSMN9005
SNN - N9005GSMH
When I enter it into sammobile, nothing comes up.
Have I got this wrong? Should I be looking for something else?
You are booting to download mode not recovery .
Boot to recovery TWRP
#N9005 model firmware are on sammobile etc.
https://forum.xda-developers.com/galaxy-note-3/general/samsung-galaxy-note-3-sticky-roll-t3237249
Booting into recovery via TWRP manager just results in the same Odin screen for me
As for the firmware - I'm not really sure which region I should pick out of those. I just thought this was an international model, but then I downloaded an app called Phone INFO and it tells me it's Vietnam. Could this be because of the rom already on there? It does also say it's a Note 7, so I'm assuming it's incorrect.
TWRP manager
DO NOT USE just boot to recovery via the vol up home and power buttons as normal .
Copy Phronesis to ext sd card and flash as per instructions .
You have N9005 Pick your area /network where you are .
Phone Info can only go by what's on your phone and you flashed DarkLord's Note 7 firmware .
Booting via manager was a last resort. I was trying the usual way and it also resulting in the same thing.
Boot to download/ Odin mode flash stock rom .
Thanks JJEgan, I figured out how to use Odin3 and Odin mode, then install Phronesis. All is good now
Hello,
I have a SAMSUNG GALAXY S6 EDGE+ which is not able to boot anymore and contains precious data which I desperately want to recover (images and text messages).
If I let the phone boot normally I got a blank screen (white)
If I press Volume Low + Home + Power the phone directly enter DOWNLOAD MODE,
with de following information on the upper left corner:
ODIN MODE
DOWNLOAD SPEED: FAST
PRODUCT NAME: SM-G928F
CA_ TYPE: CA_3
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
FAP LOCK: OFF
Secure Download : Enabled
KNOX WARRANTY VOID: 0 (0x0000)
AP SWREV: B:5 K:0 S:1
On the middle of the screen I can read
Downloading...
Do not turn off target
I never unlocked the boot-loader and/or installed custom recovery on this phone
I tried to :
Unlock boot-loader with Heimdall (or odin), in order to install TWRP
Problem: the phone is not in developer mode, so Heimdall failed to unlock the boot-loader
Recover data using Fone Paw for Android (trial 30 days version)
My phone model (SM-G928F) is not listed in the phone model list
It doesn't look like Fone Paw is able to access the device if I choose another phone model
I didn't try to :
Re-install stock Samsung-OS using ODIN
I'm afraid this will erase the data on the phone
I would appreciate if someone with some experiences on the subject could give me some advices here, what are my options to recover the data ?
Thanks for your help,
Regards,