So a while ago I rooted my phone but messed it up because I uninstalled a few too many system apps. I just dealt with it for a few months since I could still make calls (but not much else). I finally bit the bullet to look into flashing the stock rom again, but to do so it looked like I had to install a custom recovery, but to do that, unlock the bootloader. So I first unlocked the bootloader using motopocalypse (batch file didn't work but apk did), and got the expected BOOTLOADER UNLOCKED message at bootup, with fastboot saying unlocked, code 3. I then tried flashing CWM recovery via Rom Manager, and it seemed successful, but I was unable to boot to it either from the UI of ROM manager or from holding the buttons during bootup, it would just hang for a few more minutes than normal at the BOOTLOADER UNLOCKED screen, then boot up like normal. So I kept reading, found RSDlite, and was able to flash the stock rom, which I downloaded from the internet and the phone boots up fine, but now fastboot says locked, status code 2, and motopocalypse does not unlock it again (either the batch file or the apk), but I still get the BOOTLOADER UNLOCKED message at bootup. So I'm not sure if my bootloader is unlocked or not and if I can proceed with installing CWM recovery again, so i can make a full backup in case I mess something up again.
So how do I reunlock the bootloader, or verify if it's locked or not?
First, CWM and TWRP aren't official for this phone, so you can't use their apps to flash. You'll need to use fastboot, Flashify, or Rashr. Second, you're still unlocked, we've seen this error come from bad flashes. What is the complete text on your FB screen. You should be able to clear this by re-flashing with RSD. What firmware did you attempt to flash?
Sent from my HTC6525LVW using Tapatalk
RikRong said:
First, CWM and TWRP aren't official for this phone, so you can't use their apps to flash. You'll need to use fastboot, Flashify, or Rashr. Second, you're still unlocked, we've seen this error come from bad flashes. What is the complete text on your FB screen. You should be able to clear this by re-flashing with RSD. What firmware did you attempt to flash?
Sent from my HTC6525LVW using Tapatalk
Click to expand...
Click to collapse
FB screen:
Code:
AP Fastboot Flash Mode (S)
10.9B(*) (sha-61146a2, 2014-05-02 00:54:39)
eMMC Info: Size 8GB
Device is LOCKED. Status code: 2
Battery OK
Transfer Mode:
USB connected
Fastboot reason: Reboot to bootloader
usb connected
I've tried reflashing with RSD previously but no change. I could try it once more if you want.
Not entirely sure what you're asking for with the firmware version, but the image I used was for android 4.4.2, version 183.46.10.XT907Verizon.en.US.
modemman11 said:
Device is LOCKED. Status code: 2
Click to expand...
Click to collapse
I think your boot loader is still LOCKED. Mine is showing UNLOCKED. Status code: 3. You cannot flash a custom recovery on a phone with a locked BL. You need to motocalypse again!
To trace the issue from the ground up, if you're just trying to reinstall stock ROM, you should be relying on RSD instead of trying to mess with custom recoveries and BL unlocking. Just flash .10 (not .15) via RSD, root via Towelroot and you can start fresh.
Unlocking your BL is still highly recommended, though, 'cuz it's now or never.
Sent from Google Nexus 4 @ CM11
[WARNING: XDA Premium 4.0.13 lacks Signature function - do not update]
Code 3 as well.
Sent from my XT907 using XDA Free mobile app
rahimali said:
I think your boot loader is still LOCKED. Mine is showing UNLOCKED. Status code: 3. You cannot flash a custom recovery on a phone with a locked BL. You need to motocalypse again!
Click to expand...
Click to collapse
Yes, that's why I'm asking. So I've got one vote for unlocked, one for locked. As I said though, motopocalypse isn't working a 2nd time.
AndyYan said:
To trace the issue from the ground up, if you're just trying to reinstall stock ROM, you should be relying on RSD instead of trying to mess with custom recoveries and BL unlocking. Just flash .10 (not .15) via RSD, root via Towelroot and you can start fresh.
Unlocking your BL is still highly recommended, though, 'cuz it's now or never.
Click to expand...
Click to collapse
I would like to flash custom ROMs later down the road, but for now I just want to get the stock stuff going.
On a side note, the version of the image I downloaded was 183.x.x, but my mother, who has the same phone, purchased at the same time, and has never rooted it or anything, has version 182.something, and that is also the version I had before I started messing with the bootloader/recovery stuff. The two versions were released at the same time, but I don't know what determines which version you got if you just did OTA updates, or if it even matters. Speaking of OTA updates, the version I downloaded is prompting me to do an OTA update now to another 183.x.x version. I wonder if I'd be able to grab the 182.x.x ROM from my mom's phone without rooting it via fastboot or something.
The 182/183 does not matter regarding root/boot loader unlock its the .10/.15 that matters do not take the .15 without unlocking your boot loader....
We cannot teach people anything; we can only help them discover it within themselves.
So no other thoughts? What would happen if I flashed a custom rom/recovery with a locked bootloader? I tried flashing the ROM again and fb still says locked, code 2, and motopocalypse still doesn't do anything like it did the first time.
modemman11 said:
What would happen if I flashed a custom rom/recovery with a locked bootloader?
Click to expand...
Click to collapse
It won't let you flash a custom recovery. This is the difference between locked and unlocked.
modemman11 said:
So how do I reunlock the bootloader, or verify if it's locked or not?
Click to expand...
Click to collapse
If your bootloader is relocked for some reasons, try unlocking it again with
Code:
fastboot oem unlock
lem22 said:
It won't let you flash a custom recovery. This is the difference between locked and unlocked.
Click to expand...
Click to collapse
I guess what I'm asking is, will it let me flash it but then the phone won't work or will give an error on boot, or perhaps brick my phone? Or will it just not flash in the first place? Because if it's the latter, then I can just try to flash a custom ROM/recovery and if it works then I know it's unlocked.
If your bootloader is relocked for some reasons, try unlocking it again with
Code:
fastboot oem unlock
Click to expand...
Click to collapse
Code:
D:\adt-bundle-windows-x86-20140702\sdk\platform-tools>fastboot oem unlock
...
(bootloader) fastboot oem unlock [ unlock code ]
OKAY [ 0.031s]
finished. total time: 0.031s
Still locked code 2 though. Looks like it wants an unlock code from Motorola's website, I tried following the steps to get the code but it says I'm not eligible for bootloader unlock. So unless there's another way to get the unlock code...
modemman11 said:
I guess what I'm asking is, will it let me flash it but then the phone won't work or will give an error on boot, or perhaps brick my phone? Or will it just not flash in the first place? Because if it's the latter, then I can just try to flash a custom ROM/recovery and if it works then I know it's unlocked.
Click to expand...
Click to collapse
A "Code 0" locked device would refuse flashing an unofficial or older recovery. I have no idea about Code 2 though.
From what I was able to locate status code 2 indicates that the bootloader has been unlocked and relocked like by doing the whole "fastboot oem unlock unlock code" then the "fastboot oem lock" ... I'll look more into it but from what little I read it looks like it can not be unlocked again with out the Motorola unlock code...
We cannot teach people anything; we can only help them discover it within themselves.
ezknives said:
From what I was able to locate status code 2 indicates that the bootloader has been unlocked and relocked like by doing the whole "fastboot oem unlock unlock code" then the "fastboot oem lock" ... I'll look more into it but from what little I read it looks like it can not be unlocked again with out the Motorola unlock code...
We cannot teach people anything; we can only help them discover it within themselves.
Click to expand...
Click to collapse
Same here, I can see what it means but cannot find any way to get back to code 3 other than using the unlock code from Motorola, which I am unable to obtain because it says I am not eligible. Surprising that someone hasn't cracked the unlock code yet or made a keygen, people are so eager to do it with pirated computer software before the software is even released.
I've read of someone getting locked status code 2 b4 from flashing an older gpt with rsd (if I remember correctly) I think all that was required to fix it and get unlocked again was to flash the latest gpt. Very important..... Are you sure when you were unlocked you didn't ota update to .15? Because flashing .10 gpt while on .15 may be what caused your false relock
Nope, no OTA update to .15. The ZIP I have of the rom does include the gpt.bin file with the same timestamp as all the other files. I suppose I could try reflashing the whole rom once again later...
Hmm strange, I went to find the old thread I read about the gpt relock issue but it's not exactly the same as your situation.
http://forum.xda-developers.com/showthread.php?p=51436123
Until now I didn't think relock was possible due to the way unlocking works. It's a physical change, a qfuse was blown when the motopocalypse apk was run the first time. It can't be unblown lol. Wish I knew what went wrong here.
Hi XDA!
I recently unlocked my phone's bootloader to install an update for my p8lite and I want to lock it back. There is an option called relocking the bootloader and I want to know whether it is the same as locking the bootloader. Also will the ability to flash ROMs through fastboot lose after i relock it?
Thanks
Yes, it is the same, and yes, you will lose the fastboot flash ability. However, the fastboot screen won't show "Locked", it will show "Relocked"
several questions in no particular order:
Does the "OEM Unlocking" toggle do anything on the XT1572?
If I issue the fastboot OEM LOCK command after having sucessfully unlocked the device before, do I need to go through the full data wipe+send oem data+flash unlock code process again?
Lastly, I was able to flash the MM firmware for my Single SIM AISA model XT1572 despite having the bootloader locked (I think).
Is that normal that I can flash the official moto firmware using just fastboot without having to tweak with anything else?
I presume that since the digital signatures are correct the bootloader has no issue accepting the MM files.
Not quite the end of the world if I have to wipe everything and start over (it's only been a day) but I regret not knowing earlier. Nor did I expect to get this far with a relocked boot loader. Was trying to add SuperSU and found that while I can overwrite flash the stock recovery I cannot flash TWRP.
psyvenrix said:
several questions in no particular order:
Does the "OEM Unlocking" toggle do anything on the XT1572?
If I issue the fastboot OEM LOCK command after having sucessfully unlocked the device before, do I need to go through the full data wipe+send oem data+flash unlock code process again?
Lastly, I was able to flash the MM firmware for my Single SIM AISA model XT1572 despite having the bootloader locked (I think).
Is that normal that I can flash the official moto firmware using just fastboot without having to tweak with anything else?
I presume that since the digital signatures are correct the bootloader has no issue accepting the MM files.
Not quite the end of the world if I have to wipe everything and start over (it's only been a day) but I regret not knowing earlier. Nor did I expect to get this far with a relocked boot loader. Was trying to add SuperSU and found that while I can overwrite flash the stock recovery I cannot flash TWRP.
Click to expand...
Click to collapse
As far as I am concerned relocking the bootloader wont wipe your data and yes about the question regarding the stock firmware
PS: Dont relock your bootloader once you unlock it the warranty doesnt come back even if you lock it again
I just factory reset my Moto G4 and I don't intend to root or have a custom recovery. Can I lock my bootloader using fasboot oem lock? If I want to unlock my bootloader again, will I be able to use the unlock code Motorola sent to my email when I first unlocked the phone?
Thanks.
stkpxl said:
Yes to all of those. That code is unique to your phone so it will always work. In my experience though, it always asked to flash the stock firmware when you start the OEM lock procedure. Not sure if it does it no matter what, or only if you've made modifications. Either way, it's good to have a stock firmware file on hand when you do it.
Click to expand...
Click to collapse
Yeah well I'm having another problem, can't find the XT1622 reteu stock firmware...
So,
this is wierd, i had an unlocked phone with magisk.
Yesterday i decided to go back to stock, so i have flashed the stock rom and relocked my bootloader.
Now i cant get an ota update with again, a locked bootloader no root or system modification.
Anybody know why? Thanks.
That's most probably because the current inactive slot still has some modifications present. Simply unlock the bootloader again, then flash the fastboot image to both the slots (A and B) and you'll be good to go. An unlocked bootloader wouldn't prevent you from taking OTA updates. However, if you still wish, you can relock the bootloader again.
Just a tip: Keep "OEM unlocking" in developer options enabled, it could really come in handy if your device fails to boot on both the partitions somehow.
Same problem here! Do you have camera2api?
DJBhardwaj said:
That's most probably because the current inactive slot still has some modifications present. Simply unlock the bootloader again, then flash the fastboot image to both the slots (A and B) and you'll be good to go. An unlocked bootloader wouldn't prevent you from taking OTA updates. However, if you still wish, you can relock the bootloader again.
Just a tip: Keep "OEM unlocking" in developer options enabled, it could really come in handy if your device fails to boot on both the partitions somehow.
Click to expand...
Click to collapse
thanks i'll try!
Daniel91z said:
thanks i'll try!
Click to expand...
Click to collapse
Sure. Let me know how it goes. Good luck!