Hi,
I just recently had to have my charging port resoldered into my Motorola because it finally failed and ended up coming out of the phone housing on the charger connector. Prior to that, the phone was connecting to the charger, and I had two I was using. One in my car and one in the house. After I the port fell out, and until I could take it to a phone fixer, the workaround was I was charging and swapping out batteries with a Motorola Blur. What was weird is that both phone housings look identical; however, the older phone would pick up both chargers, and my Defy would not.
After they soldered in a new charging port a couple of days ago I left with clear assurance that everything was working great, and charging was a-go. Mmmhmm. On my way back home, which was an hour from the repair place, and tried to hook it up to the charger in my car. Still not charging. When I called the repair place they suggested checking it with my home charger too, once I got back home and then let them know if there was still a problem. They reassured me they had hooked up to several chargers while it was there, and all were good.
I got home, tried the home charger, and still no connection. This time when I called them back I got another person who started asking about my charger and the little lines on the underside of the metal piece that inserts into my phone. She asked if the metal tracks met the plastic on the back end of the charger itself or whether they stopped with a gap between the tracks and the plastic housing. On both my chargers I saw the tracks did NOT meet the plastic, and she said they only use Samsung chargers in their shop because it creates a better connection, and some phones need that.
Pretty sure the chargers I have were not OEM chargers for this Motorola so I am going to try to get to a place with Samsung charger so I can puzzle this out, but I am confused in that one Motorola charges and the other doesn't.
Any experience or ideas or suggestions????
Kristie
Related
I bought a Cradle for my TyTn II from Brando Web site. they are located in Hong Kong. I have been dealing with them since 2000.
they usually provide good service.
However this charger did not work, AC or USB part. I emailed them and they were kind to send me a replacement in 1 week.
Again still not charging or connecting to my computer. I skipped the cradle and tried the USB cable only still not working.
I emailed them back and they want me to ship both units back to them. I understand that there is a problem with certain connections charging or connecting with Kaiser an I tried to tell them that; I don't think they believe me.
Do Not Order this Cradle since it will not work !!
http://mobile.brando.com.hk/prod_detail.php?prod_id=03012&dept_id=039&cat_id=0996
Uh thanks for the warning, I almost bought the same thing.
mdshahed said:
However this charger did not work, AC or USB part. I emailed them and they were kind to send me a replacement in 1 week.
Again still not charging or connecting to my computer. I skipped the cradle and tried the USB cable only still not working.
Click to expand...
Click to collapse
Stupid question, but does your Kaiser connect to your computer with ANY USB cable? I'm using a cradle (from Talkietech.com) which looks identical to that one with no problems at all. Works with both a USB connection (though I re-used an existing cable) and just with the wall power plug.
If the provided USB cable isn't working, try one which you know works....
Richard
It's not only the USB cable but also the charger included.
any other USB cable works on my computer though.
Brando contacted me again yesterday they will send me a third unit. I will post once I get the third unit.
cheers.
Also returned one of these for same reason
I returned one for replacement because the led lamp was blinking like crazy. The replacement connects to my usb alright but I have not done any extensive testing of the charging performance.
Inserting the phone is also fibbly because the slot is so wide, you need to take aim and align phone before inserting. This is a real bother. Do not buy it
I bought a Boxwave cradle for a 8525 and it's light blinked and failed within hours, I returned it.
mdshahed said:
I bought a Cradle for my TyTn II from Brando Web site. they are located in Hong Kong. I have been dealing with them since 2000.
they usually provide good service.
However this charger did not work, AC or USB part. I emailed them and they were kind to send me a replacement in 1 week.
Again still not charging or connecting to my computer. I skipped the cradle and tried the USB cable only still not working.
I emailed them back and they want me to ship both units back to them. I understand that there is a problem with certain connections charging or connecting with Kaiser an I tried to tell them that; I don't think they believe me.
Do Not Order this Cradle since it will not work !!
http://mobile.brando.com.hk/prod_detail.php?prod_id=03012&dept_id=039&cat_id=0996
Click to expand...
Click to collapse
I think all these cradles (Kigidi, mobile planet, Brando) are all from the original manufacturer. They do work, but not out of the box. You have to shift the battery around left to right while inserting them to have the contacts line up properly. Cheap quality.
I bought a cradle that looks exactly like that one off eBay. But it came with a second battery for Brando's price for just the cradle alone. I've been using mine for a little over a month, and am very happy with it. The USB cable only serves for charging and connecting to a pc. To charge the second battery in the charger 'tray', the AC power adapter must be plugged in as well.
Mine also has the tricky alignment issue when inserting the kaiser, but I'm used to it. Also because of the position of the kaiser's stylus, there's no access when cradled, so I rigged a mount on the side of the cradle for a spare stylus.
Hands down the best thing about my cradle is the charger tray and second battery. It's so nice to have a fully charged battery available at any time for a quick swap. The battery that was included is only 1300 mAh, opposed to the stock 1350 mAh battery, but it fits perfectly, and I I don't find the 50 mAh difference noticeable. And considering the $24 price tag fI paid for battery and dock, it seems a steal. At this point there's no way I'm going to shell out $50 for the 1650 mAh batteries now available, but If I din't have the dock and second battery I probably would have.
I see that the pricing is up $5, still a deal:
http://cgi.ebay.com/ws/eBayISAPI.dl...tToStoreCat&refwidgettype=cross_promot_widget
brando.com shipping
This is unrelated to the topic, but I was going to order from Brando.com and was wondering how long the shipping took. It says 7-20 business days, and I was hoping it would be on the shorter end of that. (shipping to PA)
Almost every charger didnt work with my TyTn II (after I burnt up mine original one on UPS). I just went to market, looked for highest wattage supplying adapter and it was LG's 5.2Volt 5W adapter. And it recharges my TyTn II like a charm. There is something bad with recharging TyTn II.
The old motorola charger and such going-around-boozo's worked with my Vox and Excalibur but not this beast.
Interesting
i have had one of these for over 2 years. its on my desk at work. the original mains adapter packed up a long time ago and i have an old tandy one attached now. does have the random blinking lights with phone and spare battery connected, but it works.
as said before, cheap design but very handy to charge phone and battery together.
just have to be a bit lucky when you buy i guess.
despite title, i would say buy.
@dark_prince: could be the charging socket in the phone is wearing and needs bit more power to kick it in. have you tried to clean inside socket with compressed air and contact cleaner, might help.
but maybe we just have to accept that our phones are really old now and dont work as well as they used to (i know the feeling)
Q: Suddenly my car charger (cigarette lighter plugged) is not working anymore. After 5 mins. my device stops charging..... is there anybody having the same problem and knows how to solve it?
If it's after a period of time maybe a battery contact issue?
vincentvdvelde said:
Q: Suddenly my car charger (cigarette lighter plugged) is not working anymore. After 5 mins. my device stops charging
Click to expand...
Click to collapse
If you've already read the sticky posts relating to car chargers and your (mystery brand) charger isn't one of those, then maybe your phones battery terminals and connectors need careful cleaning with a cotton bud moistened with contact cleaner or IPA. I had a problem with my mains charger ceasing to charge my TyTN II after a minute or two a long time ago and after cleaning as described, the problem went away. Be sure not to spray the contact cleaner or IPA onto the phone or battery, only the cotton bud/Q-tip and then gently rub that on the spring contacts and battery terminals. How does charging via mains adapter or PC USB port go?
Flying Kiwi said:
If you've already read the sticky posts relating to car chargers and your (mystery brand) charger isn't one of those, then maybe your phones battery terminals and connectors need careful cleaning with a cotton bud moistened with contact cleaner or IPA. I had a problem with my mains charger ceasing to charge my TyTN II after a minute or two a long time ago and after cleaning as described, the problem went away. Be sure not to spray the contact cleaner or IPA onto the phone or battery, only the cotton bud/Q-tip and then gently rub that on the spring contacts and battery terminals. How does charging via mains adapter or PC USB port go?
Click to expand...
Click to collapse
Thats the thing: adapter/ USB port works for recharging.... v strange
vincentvdvelde said:
Thats the thing: adapter/ USB port works for recharging.... v strange
Click to expand...
Click to collapse
It still could be a battery contact issue as voltages may differ slightly when using the car charger compared to the other forms of charging. As an example if the Kaiser is set to stop charging when the supply voltage drops below a certain value and the car chargers voltage is lower to start with (and fluctuates with normal driving/electrical usage) then that may explain things. It's well worth doing this cleaning every so often anyway as a matter of course so give it a try and see what happens.
Additionally, could heat be a factor eg if it's sitting on a hot dash or near heater vents (the device is designed to not recharge above certain temperatures)?
Flying Kiwi said:
It still could be a battery contact issue as voltages may differ slightly when using the car charger compared to the other forms of charging. As an example if the Kaiser is set to stop charging when the supply voltage drops below a certain value and the car chargers voltage is lower to start with (and fluctuates with normal driving/electrical usage) then that may explain things. It's well worth doing this cleaning every so often anyway as a matter of course so give it a try and see what happens.
Additionally, could heat be a factor eg if it's sitting on a hot dash or near heater vents (the device is designed to not recharge above certain temperatures)?
Click to expand...
Click to collapse
Thanks for the advice, i will give it a try
if you have any adapters that allow for another usb input, nice a headphone adapter, or the HTC Multifunction Audio Cable YC A300, a ycable or anything with a USB in, try that first.
if that doesn't work, take the unit into your retailer and they will give you a new (or refurbed) unit, as your USB port may have a pin or two out of whack.
This may be weird, but my tilt used to charge just fine from most USB chargers(car, AC, usb cords). One fine day it quit charging off most chargers except the official AC charger from AT&T. I tried to fiddle with the USB pins inside as one looked like it might be a bit bent/damaged. No luck.
However, yesterday I noticed that My Settings->System->Power->Advanced settings page had following option checked:
'When device is turned on, do not charge the battery when connected to the PC'.
Once I unchecked it, it started charging of PC USB cables (obviously), but strangely enough also charging from my car charger(s). Hope this works out for you or someone else...
jrd said:
This may be weird,
'When device is turned on, do not charge the battery when connected to the PC'.
Once I unchecked it, it started charging of PC USB cables (obviously), but strangely enough also charging from my car charger(s). Hope this works out for you or someone else...
Click to expand...
Click to collapse
It is probably because your normal USB pin 4 and 5 in the cable of your other chargers are not shorted to signal that there is no data connection. So your phone thinks it is connected to a PC (or a device which might send it data), hence not charging the battery according to that setting
I have a similar infuriating problem, i have had a MDA VArio III for over a year now, had an issue with my last one and had a replacement issued in October. Now i have used the Brodit active holder (ciggy lighter version) since day one over a year ago and wit the new MDA as well. now all of a sudden phone will not charge in the holder, borrowed a friends active cradle still no charge, used a no brand usb ciggy ligther charger and charges fine!!!!
When phoe n is placed in the holder orange charging light comes on but phone does not charge and the light goes out 5 mins later!!!
any ideas anyone???
thanks
Matt
Mattcity said:
I have a similar infuriating problem, i have had a MDA VArio III for over a year now, had an issue with my last one and had a replacement issued in October. Now i have used the Brodit active holder (ciggy lighter version) since day one over a year ago and wit the new MDA as well. now all of a sudden phone will not charge in the holder, borrowed a friends active cradle still no charge, used a no brand usb ciggy ligther charger and charges fine!!!!
When phoe n is placed in the holder orange charging light comes on but phone does not charge and the light goes out 5 mins later!!!
any ideas anyone???
thanks
Matt
Click to expand...
Click to collapse
Problem solved - Pin 5 on my phone was ever so slightly out of alignment, bent back into place and all is now well! strange it only affected the brodit holders, nothing else!
Car charger failure explained
I also experienced this same problem and actually broke my phones mini usb plug in frustration at lack of charging. Got it fixed again though
The reason for this problem has become apparent since my phone was repaired. In your car, like my car when the heater is switched on it will gradually heat up the cigarette lighter socket. My charger cable like yours has a thermal safety circuit built into it. So when the ciggy socket heats up the heat is transferred to the charger plug and breaks the elec charging circuit. You might see me driving around London with my charger plug hanging out of my window (to cool it down) on a Winter's day!!! Honk if you do.
The solution would be a cheaper charger without the thermal circuit built in. Go into Maplins or PC World and ask them for that..... They dont know what your talking about, because I have already tried.......! Good luck
You just need to make sure to enable your phone to charge when connected to PC.
Start->Setting->System->Power->
UN-CHECK the box that said "When device is turned on, DO NOT CHARGE the battery when connected to PC"
hey guys, need some help here
so my phone is not charging, i tried the USB to PC, does not work neither does the wall charger, I do not get a orange led notification either. The phone would boot up for a second then turn off.
any suggestions?
I have this issue with my aftermarket battery from china, the battery is so dead that the phone doesnt even really know its there. It just happend to me yesterday. ill put up a fix tomorrow because i have my kid this weekend.
slickerxcuh said:
hey guys, need some help here
so my phone is not charging, i tried the USB to PC, does not work neither does the wall charger, I do not get a orange led notification either. The phone would boot up for a second then turn off.
any suggestions?
Click to expand...
Click to collapse
lucky for you, its the ebay battery for me its my oem battery. going to try to swap out another oem battery/charger and see if its my battery.
had the same issue, i noticed on mine that the battery pins on the phone tend to bend easily to prevent a good connection from the battery. phone would power on but wouldn't charge either.
is it the pins? i need some pictures or a video tutorial on this fix lol i have no idea what everyone is talking about, the pins look fine to me. im pretty sure that its my cable now since it didnt charge a blackberry phone either...
Damn how can this phone be so hi tech but made with th most CHEAPEST materials!
i bought a new micro usb cable, and its charging now...
slickerxcuh said:
i bought a new micro usb cable, and its charging now...
Click to expand...
Click to collapse
I bought one off of amazon and it would totally freak my phone out....no joke...it was just a wall charger no usb...now I only use the usb like the one that came with the phone and that is i.t
When you get a new phone, you should always condition the battery by letting it run completely down a few times in the beginning. When I was doing this with my phone when I first got it, after a complete drain it wouldn't charge. All i had to do was pull the battery and put it back in. Then it started charging fine. Not sure if this helps...
Also I wouldn't say these phone use cheap materials because people are not careful and bend the pins. I've removed my battery several times and the pins are perfect... If the pins aren't flexible, you wouldn't be able to get the battery in. In order to be flexible, they have to be soft. Pay attention when you are removing and replacing your battery.
You ended up figuring it out but I figured it would be good to point out that sometimes the connections on the battery/phone get dirty or pretty much any battery where it connects to the electronic.
What I usually do first when I have problems with any of my electronics turning on/charging is I take a cotton swab and dip it in rubbing alcohol. Shake it off cuz there will be alot of alcohol on there just so its not dripping and rub the connections then flip the cotton swap around then rub them again with the dry side. This doesnt work all the time but works enough for me to mention it. Static electricity will attract dirt and grime. Used to happen semi often on my touch pro since I used to have it in my pocket when I worked on a golf course.
Anyways just my 2 cents.
It seems my power cord is not charging the unit or there is something wrong with the battery, this happens after I upgraded to 3.1, any help would be much appreciated.
By any chance, did you use an extension USB3 cable on the charger at some point? I tried one last week, and immediately had the charger completely fail.
I finally concluded that the card may have caused one or more of the 5 pins on the charger base to deform.
I was able to restore it by carefully reforming the pins, very slightly upward, using a very sharp needle and a jewelers loupe. Knock on wood, it's been working fine since then.
Sent from my DROIDX using Tapatalk
No, did not use any other USB cord, the package only comes with one USB cable.
Asus support will send a RMA to me, hope BestBuy carry the transformer so that I can try their cord.
take the country adapter off the charger and reinstall it. Sometimes the small pins get bent and do not make contact.
I see more people having the same issue - the charger does not charge, I got the RMA from Asus, but really want them to send me a new charger.
How long hasn't it charged? Sometimes the charger will just stop charging out of the blue, then work a few hours later.
To make it as short as possible, My original note 3's logic board died, so I purchased another Verizon note 3 from eBay that claimed to work, but had a bad charging port. Since my original N3s charging port worked perfectly fine, I figured I'd just swap the logic board over.
Well, the blasted thing still won't charge. It won't even recognize being plugged into USB. I've tried several different cords... Ranging from the stock USB 3.0 one, to the Galaxy Tab 3 cord... To cheap Gas station car plugs... nothing seems to work at all. I've tried wiggling the cable thinking maybe it may be loose, but that didn't work. I had NO issues with the charging / USB port when it had the original Logic board in it.
So, What are the chances the logic board has messed up USB / Charging circuit? Is it possible I didn't get something connected right? I figured if I did, Something wouldn't work... But everything does, Except usb. (Speakers work, Mic works for calls, home / soft button and lights work)
EDIT: I took it back apart and checked all my connections and refreshed them, Didn't change anything :/
I even tried this: http://www.youtube.com/watch?v=mwTrlMomZ6o with no luck.
So it seems like the Logic board has bad USB. What are the chances of that happening?
Anyone at all? Gonna have to resort to a wall battery charger to use this phone.
Mine will not charge either and just started doing this about a week ago. Luckily I had bought 2 extra batteries that came with a wall charger. By the time one battery is dead the other is charged. My N3 only last about 6hrs or so.