Database Users

[Info] Unlock Bootloader, Recovery, ROOT [Noob friendly]

Hi guys I get this phone from not much time so i decide open this thread for explain the basic and necessary
1. How to unlock bootloader?
As all know Huawei web page for get unlock code not is working an also email assistance so how you can get the code,
well follow this:
- You must stay in a firmware less of 4.4.2 or 5.1.1 not 6.0 in my case I use this firmware "MT7-TL10C900B326" *If you're in 6.0, so must downgrade.
- Then to install or stay in a 4.4.2 or 5.1.1 base, download and install Kingroot (Phone will said u that could damage your phone but install it, no problem with it)
- Now open Kingroot and follow the instructions for root your device
- When all has sucessfull now install HonorTurner that can get in this thread --> http://forum.xda-developers.com/mate-7/general/unlock-code-via-honortuner-t3217651
- After to install grant the root access permission and go to this tab " Hardware Info" and look this line "WVLOCK" (This is our unlock code, so copy the code in a secure place)
- Now go to "Developer Options" If dont have enabled go to about phone info and press sometimes "Build Number", and enable "USB debugging and allow all and be sure that have installed huawei suite in your pc for get the drivers installed
- Now download the "SRK Tool" from this thread --> http://forum.xda-developers.com/mate-7/development/tool-srk-tool-huawei-beta-02-20160501-t3369990
- After to download connect your phone to your PC, dont press nothing in the usb options, only connect
- Now run the SRK Tool and press 1. Unlock bootloader, will ask if you have your unlock code (that we get it with HonorTurner) so press Y, and will start the adb service and will ask for our code, after to add the code, the phone will reboot automatically and u can go to fastmode and look that your device know is unlocked
2. How to install recovery?
* If want install MM before of all u can do it, only be sure that have your bootloader unlocked
* For enter to bootloader mode press Vol + then Vol - and Power at the same time with the phone turn off
- Donwload latest recovery for your variant, in my case M7-TL10 (You can found it here --> http://forum.xda-developers.com/mate-7/general/huawei-mt7-l09-l10-stock-firmware-ota-t3275784)
- For M7-TL10 download this --> https://mega.nz/#!9kBWnY7T!ybhARn5UNXAyxrdQZ1ytKks24eCyzxkgdVhEza6zwFQ
- Connect your phone and be sure that have enabled USB Debugging option and have unlocked the bootloader
- Run the tool and select the recovery that want install
- Wait that the tool finish to install and will reboot automatically, and enjoy!
NOTE--> For enter to recovery mode press Vol + and Power at the same time with the phone turn off
3. How to root your phone?
For 4.4.2 and 5.1.1
- Download and install KingRoot from this link: http://king.myapp.com/myapp/kdown/img/RushRoot-CafeUser-release-nolog-sdk-lc64E08B246F910AF4-b220-svn372160-201609012210b_protected_signed.apk *(Phone will said u that could damage your phone but install it, no problem with it)
- Now open Kingroot and follow the instructions for root your device and wait
- And your phone will be rooted!!
For 6.0
- Download and install a custom recovery *Is necessary unlock your bootloader for it
- Download SuperSU with/without apk from here --> https://www.androidfilehost.com/?fid=313042859668276376 or https://www.androidfilehost.com/?fid=313042859668276377 and copy to your phone, if both zip dont work so use this one https://www.androidfilehost.com/?fid=601296195406528565
- Go to recovery mode (Turn off the phone and press Vol + and Power at the same time of 5-7 seconds)
- Now search and install zip "SuperSU-vX.XX.zip" and wait that the installation finish
- Reboot and enjoy of your rooted phone in MM
I do this thread and guides in 1 place because I see that some info in the others threads are wrong or one in place and other in other place, so for this I decide do it, If any want another guide let me know and I'll add it in this thread, so enjoy of your Mate 7!

Reserved
Updating guide

Hello friend. Sorry I write you here but it seems that you are good in rooting and I need some help as I am really desperate since I can't backup, and use the apps I need without root access. I always have been rooted in any phone but since I received an OTA update, around 1 giga , giving me the Version Android 6.0 on my phone MT7-TL10C00B561 (Chinese) I lost root.
I tried some guides for uncloking the bootloader but I get the msg like it has not been used for 14days or smth like this.
Can you(or someone) please help me as this phone is out since 1 and half year and I still can't get the root.
Thank you in advance.
Sent from my HUAWEI MT7-TL10 using XDA-Developers mobile app

Do you try downgrade to first mm and then to lp??? Try do it and use kinguser to root and honor apk to read unlocked bootloader code
send from ? if I help you you can buy me ?

Thanks but I had it with KitKat than lollipop rooted (without locking the bootloader) after I updated to mm (by ota) I lost the root... :/
Any idea?
Wish I could have solved and with great pleasure I could have given u the beer!

The-Cronos said:
Thanks but I had it with KitKat than lollipop rooted (without locking the bootloader) after I updated to mm (by ota) I lost the root... :/
Any idea?
Wish I could have solved and with great pleasure I could have given u the beer!
Click to expand...
Click to collapse
As I know the unique way to root MM in huawei is with unlocked bootloader and custom recovery installed
Enviado desde mi GT-I9500 mediante Tapatalk

thank you but how can i unlock it ? and how to instal the recovery because i cant unlock bootloader from the site... :/
may we trie together please to unlock it ?

The-Cronos said:
thank you but how can i unlock it ? and how to instal the recovery because i cant unlock bootloader from the site... :/
may we trie together please to unlock it ?
Click to expand...
Click to collapse
Follow my guide for unlock bootloader, already is in OP
Enviado desde mi GT-I9500 mediante Tapatalk

Ale95 said:
Follow my guide for unlock bootloader, already is in OP
Enviado desde mi GT-I9500 mediante Tapatalk
Click to expand...
Click to collapse
just downgraded to B358 and i just lost ALL my important Data, photos, screenshoots (very important) , app datas , configurations ,,,,ALL !! I did not expected to loose the data...as i did not lost any data when i upgraded... but also i could not do any backup as i was not rooted so i could not save the app data etc... I am really sad !
Just hate this phone! Will try unlock bootloader and see if i can get root and update to MM.

So, by your guide i rooted with KingOroot the Lolipop.
Than the Phone got some updates by OTA and now i have the version B561 (all the log is in chinese)
So now i dont have the Root anymore.
I tried the recovery you have uploaded over, twrp 3.0 but when i enter recovery it does not askes me to update but only : reboot, wipe/reset , cache . (with emui logo)
so i guess i still dont have a costum recovery ?
How can i Root it with supersu if i cant choose the zip file with the supersu ?
doubt, and sorry for the silly questions :
- what is the better firmware? the asian version or the european ?
wich one should i use?
and, what about the ota updaes. how can i get them ? do i have to put the huawei recovery again after the root so i can get them ? right ?
and do the same procedure : update- installing costum recovery - root again and install again the huawei recovery ?
thank you !
waiting to root the MM as i have now unlocked bootloader.

The-Cronos said:
So, by your guide i rooted with KingOroot the Lolipop.
Than the Phone got some updates by OTA and now i have the version B561 (all the log is in chinese)
So now i dont have the Root anymore.
I tried the recovery you have uploaded over, twrp 3.0 but when i enter recovery it does not askes me to update but only : reboot, wipe/reset , cache . (with emui logo)
so i guess i still dont have a costum recovery ?
How can i Root it with supersu if i cant choose the zip file with the supersu ?
doubt, and sorry for the silly questions :
- what is the better firmware? the asian version or the european ?
wich one should i use?
and, what about the ota updaes. how can i get them ? do i have to put the huawei recovery again after the root so i can get them ? right ?
and do the same procedure : update- installing costum recovery - root again and install again the huawei recovery ?
thank you !
waiting to root the MM as i have now unlocked bootloader.
Click to expand...
Click to collapse
Hi,
It seems it didnt install. Perhaps try again? Did you run the tool mentioned in the OP?
I'm not sure what the difference is between asian and european firmwares. I've jumped between middle-east and european roms, and didnt notice much difference.
If you are rooted, and you want OTA updates, you need to first un-root (can be done in the SuperSU app) and install huawei recovery, then you will receive updates.
Then you can just re-flash TWRP and SuperSU, and you are rooted again.

The-Cronos said:
just downgraded to B358 and i just lost ALL my important Data, photos, screenshoots (very important) , app datas , configurations ,,,,ALL !! I did not expected to loose the data...as i did not lost any data when i upgraded... but also i could not do any backup as i was not rooted so i could not save the app data etc... I am really sad !
Just hate this phone! Will try unlock bootloader and see if i can get root and update to MM.
Click to expand...
Click to collapse
What app data did you say you could not backup without root access if I may ask?
Sent using Tapatalk

i dont know why it does not install the twrp. everything seems to go good but when i enter recovery is not twrp

Unlock bootloader again and flash twrp
send from ? if I help you you can buy me ?

chudy_85 said:
Unlock bootloader again and flash twrp
send from if I help you you can buy me
Click to expand...
Click to collapse
IT SAYS that the phone is unlocked so why do i have to unlock bootloader again ?
i tried to unlock it with srkt tool but after i write the boot code it says ''waiting for device''
any suggestion ?
---------- Post added at 02:31 PM ---------- Previous post was at 02:24 PM ----------
The-Cronos said:
IT SAYS that the phone is unlocked so why do i have to unlock bootloader again ?
i tried to unlock it with srkt tool but after i write the boot code it says ''waiting for device''
any suggestion ?
Click to expand...
Click to collapse
i also tried to instal theTWRP with the srk tool but still error ? how come , i have the bootloader unlocked.

sometime bootloader can lock. Do you unlock again

chudy_85 said:
sometime bootloader can lock. Do you unlock again
Click to expand...
Click to collapse
this is what i get when i try to unlock the bootloader

The-Cronos said:
this is what i get when i try to unlock the bootloader
Click to expand...
Click to collapse
Bootloader unlock code does not contain any letter, it should be numbers only, check your unlock code
Sent from my HUAWEI MT7-TL10 using Tapatalk

Blue.Ember said:
Bootloader unlock code does not contain any letter, it should be numbers only, check your unlock code
Sent from my HUAWEI MT7-TL10 using Tapatalk
Click to expand...
Click to collapse
you are right - thank you so much. i took the code i got from the honor tuner like the first page and i sucessfully installed the twrp recovery. the problem is that the phone get stucked at the huawei logo :/
cant turn it off becaose it reboots and get stack at the logo again; any suggestions ?

The-Cronos said:
you are right - thank you so much. i took the code i got from the honor tuner like the first page and i sucessfully installed the twrp recovery. the problem is that the phone get stucked at the huawei logo :/
cant turn it off becaose it reboots and get stack at the logo again; any suggestions ?
Click to expand...
Click to collapse
Install a custom recovery and wipe caché or data if still in bootloop
Enviado desde mi HUAWEI MT7-TL10 mediante Tapatalk

[HOWTO] Flash TWRP and Flash CM+GApps [Meizu M2 Note]

Hi to everybody
I'm doing this thread because I've seen that there's a lot of confussion about how to install all this things properly, and I think that concentrating the wide-spread information could help you to get rid of this. First of all I have to thanks @aaawqw and @Moyster for their great efforts.
This is going to be a recopilatory of several sources and personal tips to help you to do this the easiest way. I'm not responsible of bricked phones nor your personal problems.
Please, read the full tutorial before doing anything, to avoid bricks and those things.
PREPARE THE RECIPE
Download these files:
- Unlocking bootloader tool: HERE
- TWRP image from Moyster (creator of LOS14 for our device): here
- If you want to install a modified version of FlymeOS, use this one from Romul35 from 4PDA: here. Original post
- Last LineageOS 14 build: from this thread. PLEASE DON'T FORGET TO THANK THE DEVELOPERS
- GApps: here I recommend the nano option. Choose ARM64 and Android version 6.0.
Put those three last files into your internal memory. If you've got an microSD card, I recommend you to put them into it (it's safer and easier).
UNLOCKING THE BOOTLOADER
To unlock the bootloader go to:
- Kevin.MX @aaawqw) post: here
Finally we have a guide to unlock the bootloader of Meizu m2 note. We need Mediatek SP Flash Tool, MTK phone drivers and the images/bin files for unlocking. No modaco superboot, no fake tutorials any more
Now here's the guide:
1. Download the files I provide
Then unzip it. You'll get a folder with FlashTool, Phone drivers and unlock images.
2.Install drivers for Mediatek platform.
3.Flash the temp-unlock-secro.img via Flashtool. (secro row)
4.Flash secro.img, lk.bin, preloader_meizu6753_65c_l1.bin via Flashtool. (secro, lk and preloader rows respectively)
5.Disconnect USB data cable and power on the phone. If you see the "=>Normal boot" sign(it's quite small.......) in the left bottom cornor of the screen, then the unlock is done. You can now flash things in whatever way you like. The guide is over~~~
The full tutorial is here
The unlock tool is here
Thank you for testing&trying!
If you've seen this spoiler and didn't thank Kevin, please go to here and thank him. This motivates him and gives him the recognisement he deserves.
- Robot Hijau 97 Youtube video: here It isn't in English, but may help if you find any problem or get lost during the unlocking. Leave him a like if it helped you.
This unlocking guide only works for M571 model. If you try this with a M571C (China Telecom) model, you'll get a bricked phone (very useful if you like paperweights )
THIS METHOD DOES WORK FOR M571H MODEL. DON'T WORRY, THE ONLY ONE THAT GIVES SOME ISSUES IS THE M571C.
The great user @aaawqw states "And Meizu M571C should use the same method of meizu m2 (mini), a shell script for frp unlock. But no recovery images yet…Different hardware and partitions"
Tips to unlock the bootloader easily:
- If you're going to do it from a Windows 10 or 8 pc, have in mind that to install unsigned drivers you'll have to unlock the feature in your pc. A guide to do this: here
- Select the images to flash and hit the Download button before connecting your Meizu (pressing Vol Down button). This will help you if it turns on and off and makes the flashing impossible.
- Download the guide or see the video to correctly follow all the steps. You don't want to lose your phone, don't you? Don't try to mix guides, because you may skip a step and brick your phone. The video and Kevin.MX guide are the same procedure, they both are safe.
INSTALLING TWRP
Once done this part, we'll proceed with the installation of TWRP recovery image. There are two ways, choose the easier to you:
- Flash TWRP from SP Flashtool (original idea from @widagdag. The post: here)
+Turn off your device
+ By using your pc or laptop, extract the TWRP zip for meizu m2 note, there's a file "recovery.img"
+ You can flash it via SP flash tool (clicking the recovery, then select the file)... then click Download, wait until finished!! (Check symbol)
+ You can reboot ur device now, unlocked bootloader and installed twrp!
*The profit is u didn't need to root first and install any flash tool such as Rash, FlashFire, Flashify, etc. saving you some time
Click to expand...
Click to collapse
- Flash the recovery image from Flyme:
+ Get root access (if you do, skip this step). You can get it downloading Kingroot: here. Just install this apk and follow the steps
+ Unzip TWRP zip into a known folder
+ Download Flashify from the Playstore
+ Grant superuser access
+ (Optional) make a backup of your current recovery going to backup tab
+ Tap Recovery Image
+ Choose a file
+ Find TWRP img that you unzipped before and flash it
Click to expand...
Click to collapse
INSTALLING CM AND GAPPS
We're close to the end of this post. The final step: installing your desired ROM and GApps. I will flash CM from the thread whose link is at the download section.
I hope you've put it into your memory (internal/external) as we said
Ok so:
- Turn off your phone
- Go into the TWRP recovery (Vol up+power)
- (Optional but recommended) Make a backup of Flyme, just in case you don't like the new ROM and would like to go back to Flyme. If it takes up too much memory, move it to your pc after making the backup.
- Go to Wipe menu
- Go to advanced wipe
- Select these:
+ System
+ Cache
+ Dalvik Cache
+ Data
- Swipe to do the wipe
- Go to install.
- Select your zip image (in my case the cm13 I downloaded).
- Install also the GApps zip file you downloaded
- Restart to System, and check what you've done.
Some final tips:
- Make the backup, seriously, it takes 10 min and you'll have a Flyme backup if you don't like CM.
- If you want to transfer all your apps and their data from Flyme to your new ROM, use Titanium Backup.
- If you want to install Xposed Framework, it's the same procedure: enter into TWRP, tap install, select the zip and swipe.
- This won't delete your images or videos, but I would recommend to transfer them to a microSD card or your PC.
- Yes, you need to do all this to install a custom ROM. Yes, even unlocking the bootloader. Don't try to skip a step if you aren't sure about what you're doing.
I think that's all, I'll update this post if I lost anything.
I hope this helped you to move into CM world. If you have any doubt don't hesitate to ask.
I know this seems exhausting, but trust me, it worths it. Welcome to the custom ROMs world in your Meizu M2 Note. Let the magic begin.
ADDITIONAL GUIDES
RELOCKING THE BOOTLOADER
If you want to relock the bootloader just follow this simple steps:
Flash the original recovery image from Flashtool of from Flashify (the steps are the same as installing TWRP). You can find this image here
From there, install an update.zip (download them from the official flyme web: here and put it into the storage )
Now you have flyme again with a locked bootloader.
INSTALLING FLYME WITH TWRP
It's very important that you don't install an update.zip from the original Flyme page, because you will cause a bootloop. To get the flyme updates, you can follow one of these two methods:
METHOD 1: 4PDA
-Download the modified zips from 4PDA: here]. Translate it to English. It's on custom firmware>Flyme
-Flash them from TWRP
METHOD 2: DO IT YOURSELF
-Download the update.zip file from the Flyme page
-Open it and remove the preloader- files
-Flash it from TWRP. It will give you an error: IGNORE IT.
Reboot and done, you've got Flyme and TWRP.
UNBRICK A PAPERWEIGHT
BIG THANKS TO @numpea FOR THIS:
This just a firmware that has all the partitions and can be used to unbrick to device using SPFlashtool
Here is the link:
FIRMWARE
- Flash temp_unlock_secro.img with sp flashtool like you do when unlocking the bootloader.
- When done, disconnect the device and add the firmware to sp flashtool. You need to select "format all+download", click on "Download" and connect the device. The flashing process will start. After it finishes, the device will start again.
You wil notice that you lost your imei number you can add it back by:
Using MTK Engineering Mode (does not requires root)
Open engineering mode » Click on Engineer Mode (MTK) » Swipe left to Connectivity » click on CDS Information » Radio Information
Click on phone 1 if you want to change your sim 1 or choose Phone 2 to change sim 2 IMEI, follow this guide:
For Phone 1: “AT+ EGMR=1,7,”YOUR NEW IMEI NO” (make sure you add a space in between AT+ & EGMR)
For Phone 2: “AT+ EGMR=1,10,”YOUR NEW IMEI NO” (make sure you add a space in between AT+ & EGMR)
Using Chamelephon (requires root, but much more easier)
Just copy the IMEIS from the phone's box and put them into the app.
hope this is helpful
Click to expand...
Click to collapse
I'll keep updating the info!

Really complete, I could unlock my M2 Note and install CM-12.1 ! Thanks !

Moyster said:
Really complete, I could unlock my M2 Note and install CM-12.1 ! Thanks !
Click to expand...
Click to collapse
Moyster xDD :laugh::laugh: Thanks to you, without you this wouldn't have been possible

Pretty much covered all, just state the Armv7 Android level API 21 64bit, 5.1 Micro or Nano for gapps. They might get confused on what to choose.

Xtian Rey said:
Pretty much covered all, just state the Armv7 Android level API 21 64bit, 5.1 Micro or Nano for gapps. They might get confused on what to choose.
Click to expand...
Click to collapse
Very true, thanks a lot. I introduced the platform and the Android version of GApps

Thanks nice guide... Very useful for everyone who want play and modified the M2 note.

"This unlocking guide only works for M571 model. If you try this with a M571C (China Telecom) model, you'll get a bricked phone (very useful if you like paperweights*)"
I Am Using M571C, But Everything Fine.
Sent from my M2 Note using XDA Forums Pro.

Mr0oHo0 said:
"This unlocking guide only works for M571 model. If you try this with a M571C (China Telecom) model, you'll get a bricked phone (very useful if you like paperweights*)"
I Am Using M571C, But Everything Fine.
Sent from my M2 Note using XDA Forums Pro.
Click to expand...
Click to collapse
I include this on the guide. I read it bricked the phone in several cases, but I'm glad yours didn't.

Thanks for your guideline , it helps a lot !

Great work lol
Another thing is…ShevT's recovery has no problem in cache partition.Only my broken recovery did… So remove the cache fixing partAny problem just send me a private message. I'll check when i have time.
---------- Post added at 04:00 PM ---------- Previous post was at 03:58 PM ----------
And Meizu M571C should use the same method of meizu m2 (mini), a shell script for frp unlock. But no recovery images yet…Different hardware and partitions…
Another thing is, Kingroot is not suggested. It cannot be detected by Flashfire and some other tools. And cannot be replaced by SuperSU. So Kingo Root+SuperSU might be better.

aaawqw said:
Great work lol
Another thing is…ShevT's recovery has no problem in cache partition.Only my broken recovery did… So remove the cache fixing partAny problem just send me a private message. I'll check when i have time.
---------- Post added at 04:00 PM ---------- Previous post was at 03:58 PM ----------
And Meizu M571C shoukd use the same method of meizu m2 (mini), a shell script for frp unlock. But no recovery images yet…Different hardware and partitions…
Click to expand...
Click to collapse
https://github.com/Moyster/android_device_meizu_m2note/blob/cm-12.1/BoardConfig.mk#L10
Line 10 to 15 you have the partitions size
Code:
$ cat /proc/partinfo
example :
Name------------Start-------------Size
recovery 0x0000000004840000 0x0000000001400000
Take the Size value : "0x0000000001400000" => hexadecimal to decimal => 20971520 = recovery partition size
PS: I don't think the hardware is "that" different, at least, the kernel meizu released should contain both phone models/drivers

This unlocking guide only works for M571 model.
Click to expand...
Click to collapse
Mine is M571H, can I proceed?

Qeemi said:
This unlocking guide only works for M571 model.
Mine is M571H, can I proceed?
Click to expand...
Click to collapse
Mine too and it worked. I can't assure you anything, but I think that the problem are m571C which are different. Good luck if you're going to give it a try!

Moyster said:
https://github.com/Moyster/android_device_meizu_m2note/blob/cm-12.1/BoardConfig.mk#L10
Line 10 to 15 you have the partitions size
Code:
$ cat /proc/partinfo
example :
Name------------Start-------------Size
recovery 0x0000000004840000 0x0000000001400000
Take the Size value : "0x0000000001400000" => hexadecimal to decimal => 20971520 = recovery partition size
PS: I don't think the hardware is "that" different, at least, the kernel meizu released should contain both phone models/drivers
Click to expand...
Click to collapse
See it. I'll give a try on m2 note(M571C, China Telecom). At least try to build twrp But seems my pc's hdd is not enough No space for source code

little problems.
bootloader unlocking and twrp and roms works very well..
1. OTG is working for me.. :good:
2. unfortunately my phone is not detected by PC..
(show USB is not connected, USB debugging is not accessible..)
3. little bit lag here and there..
4. wifi works well :good:
Need more optimization.. Expecting lot more from you
thankyou very much for this :good:
DOUBT : so bootloader is unlocked, now it is possible to make good MM and N based CM roms ?

dinkan01 said:
bootloader unlocking and twrp and roms works very well..
1. OTG is working for me.. :good:
2. unfortunately my phone is not detected by PC..
(show USB is not connected, USB debugging is not accessible..)
3. little bit lag here and there..
4. wifi works well :good:
Need more optimization.. Expecting lot more from you
thankyou very much for this :good:
DOUBT : so bootloader is unlocked, now it is possible to make good MM and N based CM roms ?
Click to expand...
Click to collapse
hi,which build of cm 12 you put in phone?

M571U
I have the Meizu M571U Model. Can I do this or will it be bricked?
Thank you very much

venturaj said:
I have the Meizu M571U Model. Can I do this or will it be bricked?
Thank you very much
Click to expand...
Click to collapse
It won't, the only problematic model is the M571C, have fun

LBA97 said:
It won't, the only problematic model is the M571C, have fun
Click to expand...
Click to collapse
How can I check which model my m2 note is..?

[email protected] said:
How can I check which model my m2 note is..?
Click to expand...
Click to collapse
Check the store page you bought it from. If you bought it from China, then probably it's a M571C. Good luck

[GUIDE] Error 7 Solution While flashing 7.1.2 ROMs

A brief Intro.
Starting from the 7.1.2 ROMs most of the developers decided to follow the process of checking modem version at the time of flashing the rom. Many peoples ended up in
"Error 7- assert(xiaomi.verify_modem("MSM8976.LA.1.0.c3-30041-STD.PROD-1.77504.1.83742.1") == "1")"
The main reason for this is the outdated firmware or it is happened to those who had unofficially unlocked the bootloader.
Some more info..
1. You must be on MM build bootloader. If you are unofficially unlocked bootloader it will give you ERROR7.
@TheStrix have alreday given a short information about it in his Official LineageOS thread. If you are unaware of it read it here
2.Outdated Firmware.
Your firmware must be from from MIUI Global DEV v7.5.4 or above.
Get MIUI Global DEV v7.5.4 from here
or the latest firmware from here
NB:-
- Iam using the MIUI Global DEV v7.5.4 firmware. All working fine including Volte. I dont know about the second one,you can give it a try.
-If you are unofficially unlocked ,MIUI Global DEV v7.5.4 will re lock your bootloader you will end up in bootloop.
- I will not be reponsible for any damages.
Solution 1 [Permanent Solution] ..
1. So if you are unofficially unlocked, i will suggest to clean flash the latest MIUI Fatboot Rom. Kenzo users get it from here.
2.Flash it using MIFlashTool ,and officially unlock it.
HOW TO UNLOCK THE BOOTLOADER OF REDMI NOTE 3?
PART 1 : REQUESTING FOR UNLOCK PERMISSION
Step 1 – Open up your favorite web browser in your computer (Chrome is recommended) then go to this link
Step 2 – You’ll see the official page of “Unlock Your Mi Device”. Now simply click on the blue “Unlock Now” Button in the middle of the page.
Step 3 – You’ll see a login page in the next page which is in Chinese. If you use Google Chrome to open the page, then you can simply use its built-in Google Translate feature.
Step 4 – Once logged in, you’ll see the Unlock Application Permissions page.Now simply fill in all required fields then click on that green Apply Immediately button.
Step 5 – In the next page, you’ll need to enter a verification code sent to you via SMS. Check your phone for any SMS verification sent by Xiaomi server. The code is usually valid for only 5 minutes so you need to enter it immediately.
Step 6– Once you have submitted the 6 digits code, you’ll then be redirected to another page saying that from the point toward all you need to do is just waiting for Xiaomi Developers to review and approve your application. Once approved, you’ll get another SMS which normally arrives in 15 min(Atleast for me. For some it may take time). The approval process is manual so just be patient on this.
PART 2 : BOOTLOADER UNLOCKING PROCESS
Requirements for Bootloader Unlocking :
-An active Mi account linked to your device, your phone number and it has permission to proceed with bootloader unlock (follow previous steps above)
-Please backup your data for just in case scenario.
-Again, if you are not fully aware of flashing custom ROM, then you better stay away of unlocking your phone’s bootloader.
Download Mi Flash Unlock tool for Windows here, and install it on your computer / PC.
Step 1 – On your device, please login to your Mi account.
Step 2 – Put / reboot your device into bootloader mode. To do that, simply turn off your device, press the Power button and Volume down ( – ) button at the same time.
Step 3 – On your computer, open MiFlash Unlock tool you’ve just installed. Click on the Agree button when asked.
Step 4 – Login to MiFlash Unlock tool with the same Mi Account.
Step 5 – Now connect your phone to computer using its USB cable.
Step 6 – Once your phone is connected, the Unlock button will become active. Next, simply click on the Unlock button to start the process. The unlock process will take about 10 – 15 seconds to complete. That’s all.
After unlocking your phone’s bootloader, you’ll be able to flash TWRP and other custom ROM. Enjoy..
Please take these as your concern upon unlocking bootloader :
One Mi account could only unlock one device within 30 days.
If you see a notice saying that “current user is not logged in connected device” then please reboot your device normally then login with your account in the device (see Step 1).
Unlocking bootloader will wipe all user data especially if your device is encrypted. That’s why you’ll need to create backup before going to proceed.
Neither Xiaomi or I will guaranteed if anything goes wrong during and as the result of unlocking. Proceed with your own risks.
Also, unlocked Xiaomi devices will be marked in the official service end.
PART 3 : Installing TWRP and Custom Rom.
Step 1 –. Get latest TWRP from here. Flash it via fastboot { I will not be explaining that in details}
Step 2 –. Take back up of EFS using Twrp. Wipe Everything including internal storage.
Step 3 –. Install Firmware-Rom-Gapps in order. Error 7 will be solved
Solution 2[Temporary Solution] ..
Only try this method if you are not able to officially unlock your device . Dont use the Firmware by Strix.It will relock your bootloader.
Step1 - Downalod the rom to your pc.
Step2 - Use any notepad. Suggestd one Notepad++. Get it from here
Step3 - Open the Rom.zip{dont extarct}. Navigate to META-INF/com/google/android/updater-script.
Double click on updater-script and open it with notepad++. Edit and remove this line from the file
Code:
assert(xiaomi.verify_modem("MSM8976.LA.1.0.c3-30041-STD.PROD-1.77504.1.83742.1") == "1")
Allow the file to save and close the zip.{Rom will recompress by itself}.
Step4 - Flash in order. Firmware -Rom-Gapps.
Some FAQ's ..
1. Iam not getting volte
Ans:- Restore the EFS. Try rebooting your phone 2 or 3 times. After Clean flash ,I had to reboot 3 times to get volte working. :fingers-crossed:
2.Iam not able to see FingerPrint Option?
Ans:- Your are defenitely on an old Firmware.Update to Latest Firmware It will work.
3.Iam getting Some other Errors. :crying:
Ans:- Post your Screen Shot Below.Will Check.
4.Iam getting some other problems in ROM.
Ans:- Report it with proper logs to the developer.Iam helpless.
5.I bricked my device
Ans:- I will Laugh at you. Always do everything at your own risk. :silly:
Some Advices ..
* At least use search once in your life time. From my observation its clear that no one ever uses search in the Rom Section. Even is there is a solution in every page you keep on asking same questions.
*Dont flood the thread.
*Dont qoute the whole op.
*Respect other members
If this was of help to anyone hit the like :fingers-crossed:

First

There's a problem with not updating the bootloader (aboot) and staying with a LP bootloader, you will most likely encounter bootloops. Say you edit that code line for the modem check, it will flash but it won't boot/work properly. You must update the bootloader in order to boot newer ROMs. And you need to update the modem and other stuff so you won't face issues. You need to offcially unlock no matter what you do, it's very easy.

Asphyxiate666 said:
There's a problem with not updating the bootloader (aboot) and stay with a LP bootloader, you will most likely encounter bootloops. Say you edit that code line for the modem check, it will flash but it won't boot. You must update the bootloader in order to boot newer ROMs. And you need to update the modem and other stuff so you won't face issues. You need to offcially unlock no matter what you do, it's very easy.
Click to expand...
Click to collapse
that's why I wrote temporary method..only for those who are lazy and not willing to start from root by flashing fastboot rom

adithyan25 said:
that's why I wrote temporary method..only for those who are lazy and not willing to start from root by flashing fastboot rom
Click to expand...
Click to collapse
I understand but with their laziness they will ruin their devices then come here and say "omg sir it doesn't boot wtf is this useless rom crap developers".

Asphyxiate666 said:
I understand but with their laziness they will ruin their devices then come here and say "omg sir it doesn't boot wtf is this useless rom crap developers".
Click to expand...
Click to collapse
I know that...most people don't even bother to use search..even if there is a solution just above their question they won't give a damn to look it..

guys help..i had officially unlocked the bootloader..and i don't remember the firmware i had installed...n i am still getting the error code 7..do i need to flash the kenzo global or dev firmware from the link..??

PrathaM X said:
guys help..i had officially unlocked the bootloader..and i don't remember the firmware i had installed...n i am still getting the error code 7..do i need to flash the kenzo global or dev firmware from the link..??
Click to expand...
Click to collapse
you must format your phone (not wipe) using twrp then install fw-rom-gapps...use fw by strix from above method(permanent)

I flashed v8.5.1.0 using MiFlash and it said flash completed successfully. However now it is stuck on the Mi splash screen with "powered by android" logo at the bottom. The dots are moving so I assume it is loading but it's been on that same screen for the past 10 minutes now.
Previously, the bootloader was officially unlocked but some stuff broke as I tried to upgrade to a new ROM and that's why I decided to flash v8.5.1.0 in order to go back to stock and start from scratch.
Edit: It works!

adithyan25 said:
you must format your phone (not wipe) using twrp then install fw-rom-gapps...use fw by strix from above method(permanent)
Click to expand...
Click to collapse
I'm on Marshmallow boot loader (flashed faatboot ROM) and officially unlocked & formated data.
Yesterday I did a update RR ROM (9th july) then I got error 7.
at the time of flashing I was on latest firmware 7.7.6.
So reflashed 7.5.4 firmware and it's worked.
So we should always stick to 7.5.4 firmware ? For avoiding error 7?

baku2313 said:
I'm on Marshmallow boot loader (flashed faatboot ROM) and officially unlocked & formated data.
Yesterday I did a update RR ROM (10th july) then I got error 7.
at the time of flashing I was on latest firmware 7.7.6.
So reflashed 7.5.4 firmware and it's worked.
So we should always stick to 7.5.4 firmware ? For avoiding error 7?
Click to expand...
Click to collapse
yep..in my knowledge the latest firmware has a change in modem version(updated version) so it wont match with one in updater script... so i will say to stick with some older firmware unless the developers chabge it in the roms update-script file...
iam using strix fw 7.6.15

adithyan25 said:
yep..in my knowledge the latest firmware has a change in modem version(updated version) so it wont match with one in updater script... so i will say to stick with some older firmware unless the developers chabge it in the roms update-script file...
iam using strix fw 7.6.15
Click to expand...
Click to collapse
Can you provide me the link please.

baku2313 said:
Can you provide me the link please.
Click to expand...
Click to collapse
its in the aosp extended 4.4 update op...
im quite busy now...i will share it later if you havent found it .... you will find the link in aosp extended thread

adithyan25 said:
its in the aosp extended 4.4 update op...
im quite busy now...i will share it later if you havent found it .... you will find the link in aosp extended thread
Click to expand...
Click to collapse
Strix updated his thread with 7.7.6 firmware (Kenzo).

I am on MM on Redmi note 3 Snapdragon version! I tried firmware (7.7.0 I guess) and then ROM Zip but still got the Problem ! Any thing else I can do?

What if i have locked bootloader and flashed twrp through miflash?

coolguy22 said:
What if i have locked bootloader and flashed twrp through miflash?
Click to expand...
Click to collapse
In theory it should work I guess? Assuming you used the guide from @khajiit here you should have a MarshMellow bootloader, as the MIUI version linked there is based on MM (kate_global_images_6.11.3_20161103.0000.00_6.0_global_16db0fc5fa), so it shouldn't relock. Can't try myself since I unlocked mine recently.

Amon_Re said:
In theory it should work I guess? Assuming you used the guide from @khajiithere you should have a MarshMellow bootloader, as the MIUI version linked there is based on MM (kate_global_images_6.11.3_20161103.0000.00_6.0_global_16db0fc5fa), so it shouldn't relock. Can't try myself since I unlocked mine recently.
Click to expand...
Click to collapse
Ok so if i get the latest firmware and install some 7.1.2 rom it shouldn't bootloop?

coolguy22 said:
Ok so if i get the latest firmware and install some 7.1.2 rom it shouldn't bootloop?
Click to expand...
Click to collapse
In theory, it should work.

..

p8 lite unlock bootloader

Hi Dears
i have p8 lite ALE-L21
i cant unlock bootloader
i searched a lot but i found old way from huawie site that not working now
so how i do this now after site closed ?
the reason for i want to unlock bootloader that i want to install twrp and root my device or use any other ROM
so please help me
thanks and waiting your answer

the reason for i want to unlock bootloader that i want to install twrp and root my device or use any other ROM
so please help me

zamlkawy said:
the reason for i want to unlock bootloader that i want to install twrp and root my device or use any other ROM
so please help me
Click to expand...
Click to collapse
Hi
If you want to unlock bootloader, you have to:
- downgrade to the first version of Android provided by Huawei
- root it with one of the dozens of one-click-root tools (personally I use Kingroot)
- do what mentioned here https://forum.xda-developers.com/p8lite/general/alternative-method-unlocking-bootloader-t3799294
- done :highfive:
Worked well with me, without problems

thanks for your reply
where i can get first version of Android provided by Huawei to this device

zamlkawy said:
thanks for your reply
where i can get first version of Android provided by Huawei to this device
Click to expand...
Click to collapse
Do you have single SIM or dual?

faby GT said:
Do you have single SIM or dual?
Click to expand...
Click to collapse
I have the same question, do you have the rom for dual-sim?

xperia81 said:
I have the same question, do you have the rom for dual-sim?
Click to expand...
Click to collapse
Do you mean stock ROM first version? Sure!
Only for dual SIM:
- download these two packages http://download-c.huawei.com/download/downloadCenter?downloadId=79348&version=317012&siteCode=it and https://docs.google.com/uc?id=0B7aKdgGvGVwrRHBaNVo4VHdDVk0&export=download
- put JUST THE FIRST LINK's unpacked "update.app" file inside your phone's folder "dload" (if you don't have one, create it)
- shut down the phone
- boot up the phone by keeping pressed all the buttons (Power + volume up + volume down)
- wait until the process ends
- then delete the "update.app" from your phone and replace it in the same "dload" folder with the "update.app" file from the SECOND link unpacked folder
- shut down and then boot up the phone with all buttons pressed
- done :highfive:

faby GT said:
Do you mean stock ROM first version? Sure!
Only for dual SIM:
- download these two packages
- put JUST THE FIRST LINK's unpacked "update.app" file inside your phone's folder "dload" (if you don't have one, create it)
- shut down the phone
- boot up the phone by keeping pressed all the buttons (Power + volume up + volume down)
- wait until the process ends
- then delete the "update.app" from your phone and replace it in the same "dload" folder with the "update.app" file from the SECOND link unpacked folder
- shut down and then boot up the phone with all buttons pressed
- done :highfive:
Click to expand...
Click to collapse
Yes I meant stock rom.
Is bootloader unlock necessary in this way?
Thanks for this explanation, I will try it out soon.

xperia81 said:
Yes I meant stock rom.
Is bootloader unlock necessary in this way?
Thanks for this explanation, I will try it out soon.
Click to expand...
Click to collapse
No, they're official update packages.
Most important thing: you don't have to have TWRP installed (just stock recovery)
PS: if it was helpful, hit "thanks" button :highfive:

Hi. During recent days I had same problem. I've got ALE-L21 dual sim comp. number ALE-L21C09B180 and while i'm trying to flash from dload folder with first link i'm getting stuck at around 8% with an flashing error ;/ Any ideas?

koperkowy said:
Hi. During recent days I had same problem. I've got ALE-L21 dual sim comp. number ALE-L21C09B180 and while i'm trying to flash from dload folder with first link i'm getting stuck at around 8% with an flashing error ;/ Any ideas?
Click to expand...
Click to collapse
Hi
first of all, is your bootloader LOCKED? Do you have stock recovery (=no TWRP)? (I know you are trying to get unlock code, but maybe you had brick problems and lost code)
If yes, try firstly the easiest things:
Delete update.app
Delete dload folder
Reboot
Connect phone to PC
Download again with your PC the first zip and extract it (in your PC), and then copy the dload folder in your phone
Try again
If it still doesn't work, let me know

My P8 lite has locked bootloader (technically it's my mother's phone, I want to flash it with custom rom coz it's really slow and unusable on it's stock rom). Do the bootloader was never unlocked, I do not have a code to unlock it.
What's steps should I undertake to flash it successfully?
1. Unlock bootloader
2. Root
3. Flash twrp
4. Flash rom
Is that correct? How do I unlock bootloader while Huawei stopped providing unlock codes?
I really appreciate your help in this post, thanks faby.

koperkowy said:
Is that correct? How do I unlock bootloader while Huawei stopped providing unlock codes?
I really appreciate your help in this post, thanks faby.
Click to expand...
Click to collapse
Get code from dc-unlocker site like me. Cost a few $.

zkoz said:
Get code from dc-unlocker site like me. Cost a few $.
Click to expand...
Click to collapse
Why pay if you can get it free?
koperkowy said:
My P8 lite has locked bootloader (technically it's my mother's phone, I want to flash it with custom rom coz it's really slow and unusable on it's stock rom). Do the bootloader was never unlocked, I do not have a code to unlock it.
What's steps should I undertake to flash it successfully?
1. Unlock bootloader
2. Root
3. Flash twrp
4. Flash rom
Is that correct? How do I unlock bootloader while Huawei stopped providing unlock codes?
I really appreciate your help in this post, thanks faby.
Click to expand...
Click to collapse
You have to downgrade it first to Android 5
Root it with Kingroot
In your PC, install this https://forum.xda-developers.com/showthread.php?t=2588979 if you don't have access to ADB commands
Do then what mentioned here (after connecting your phone to your PC and enabling "USB debug" inside developer options in your P8 lite) https://forum.xda-developers.com/p8...ve-method-unlocking-bootloader-t3799294/page1
Unlock bootloader with the code you got from the above step (just follow what written in the link)
Flash TWRP
(If you want, flash custom ROM or updated stock ROM)
(If you did it, boot the ROM and then reboot to TWRP)
Flash magisk (the safest way to get root)

simply F said:
You have to downgrade it first to Android 5
Root it with Kingroot
In your PC, install this https://forum.xda-developers.com/showthread.php?t=2588979 if you don't have access to ADB commands
Do then what mentioned here (after connecting your phone to your PC) https://forum.xda-developers.com/p8...ve-method-unlocking-bootloader-t3799294/page1
Unlock bootloader with the code you got from the above step (just follow what written in the link)
Flash TWRP
(If you want, flash custom ROM or updated stock ROM)
(If you did it, boot the ROM and then reboot to TWRP)
Flash magisk (the safest way to get root)
Click to expand...
Click to collapse
For some reason I cannot proceed with rollback flashing. Even after deleting dload folder, downloading fresh file, rebooting the phone. Still stuck on 8%.

koperkowy said:
For some reason I cannot proceed with rollback flashing. Even after deleting dload folder, downloading fresh file, rebooting the phone. Still stuck on 8%.
Click to expand...
Click to collapse
Hi
If you go to system information inside settings, what do you see as "Android version"?

simply F said:
Hi
If you go to system information inside settings, what do you see as "Android version"?
Click to expand...
Click to collapse
Android 5.0.1
Emui 3.1.1
Compilation number ALE-L21C09B180

koperkowy said:
Android 5.0.1
Emui 3.1.1
Compilation number ALE-L21C09B180
Click to expand...
Click to collapse
Hi
"Rollback" (or downgrade) is the contrary of update. So, when I said "rollback to Android 5" I meant "downgrade from Android 6 to Android 5"
You can't downgrade because you HAVE Android 5, so you have just to BACKUP EVERYTHING (because unlocking bootloader you erase all data) and follow the step-by-step guide I have written above, skipping the "rollback" step :highfive:
Less things to do :good:

simply F said:
Hi
"Rollback" (or downgrade) is the contrary of update. So, when I said "rollback to Android 5" I meant "downgrade from Android 6 to Android 5"
You can't downgrade because you HAVE Android 5, so you have just to BACKUP EVERYTHING (because unlocking bootloader you erase all data) and follow the step-by-step guide I have written above, skipping the "rollback" step :highfive:
Less things to do :good:
Click to expand...
Click to collapse
That's what I thought as well but I cannot get through the first step witch is rooting by kingroot. I'm just getting an information that kingroot wasn't able to root my device.

koperkowy said:
That's what I thought as well but I cannot get through the first step witch is rooting by kingroot. I'm just getting an information that kingroot wasn't able to root my device.
Click to expand...
Click to collapse
Hi
Enable usb debugging inside developer options, then try again until it works (cause it works).
If it still doesn't work, download Kingroot for pc and connect phone to it.
Else, try with other one-click-root tools (as Kingoroot, there is not much imagination for names :laugh: )
Done the root, the procedure is much easier.

Downgrade From Android 10 to Android 9 is working now

Android 10 downgrade.
now the tools are available in realme website to unlock the bootloader...
install deep testing apk and unlocking the boot loader with the android 10 ( procuder will be found in realme website)
After the bootloader is unlocked......follow the procedure below..
second reboot to bootloader and flash the twrp recovery
and reboot using fastboot command itself
it will go straight to twrp recovery mode.
just give wipe data function which is default...
then flash the android 9 ozip , after that dont reboot to system
go back and flash the stock recovery from android 9 which is attached with this post and then reboot..
now you are back to android 9.
this method is working for me ..
after sitting many hours with stucked twrp recovery i just flashed the stock recovery and it get in to the device
Please read whats the state of my realme x2 pro so that you can understand what I have done.
I purchased the realme x2 pro 12gb/256 in the uk , it is shipped with the android 9, there was some OTA update and I had done that and the phone was still in Android 9 with some bugs fixed. Again I recheked the software update for Realme ui update but nothing was found.
So I headed to realme uk website and downloaded the Android 10 realme ui ozip , copied to the phone and updated. Now the phone was in android 10 with realme ui.
The software update is good but I don’t like the finger print animation and also I noticed a sight battery drain,but I am not sure if it was same like in android 9 , I mean the batter life. So decided to go back android 9 . so after so many tries and all finally downgraded to android 9 with the bootloader locked and widevine to L1 and google pay working. Now all stock and all finger print this and that working !!!
Downgrade procudure :-
Backup All the things that are required, All will be wiped.
1.First thing is to unlock the bootloader in Android 10 because of I updated to android 10.
Follow this link below , download the deep testing apk and unlock the bootloader.
https://c.realme.com/in/post-details/1253651898825703424
2.Make sure you all had the proper working adb drivers in pc and android bootloader drivers,
After completing the 1st step , Download the twrp from the link below:
I downloaded the one in this name TWRP 3.3.1-13 Unofficial by mauronofrio
https://forum.xda-developers.com/re...covery-unofficial-twrp-realme-x2-pro-t3997879.
How to flash twrp in realme x2 pro follow this guide below:
https://forum.xda-developers.com/realme-x2-pro/how-to/guide-unlocking-bootloader-to-getting-t4010189
follow the procedure above and until flashing recovery and don’t flash vbmeta and all
3. Download the Android 9 firmware with stock recovery , this was the lastest one I dowloaded from xda
(https://forum.xda-developers.com/realme-x2-pro/how-to/rmx1931ex11a-10-available-t4059607)
4.Downloading stock recovery :
https://sourceforge.net/projects/rmx1931ex-stock-files/files/RMX1931EX_11_A06_GLOBAL.zip/download
download this zip file and use only the recovery.img after unzip , this is the only file we need from this folder
Second part:
I Assume the bootloader is unlocked , the device wiped and rebooted to os , copy the ozip in the and stock recovery in internal memory, we might need to use this for later.
now flash the twrp using the guide above and reboot to twrp recovery.
In twrp install the android 9 ozip that we downloaded in the phone memory , after it flashed don’t reboot.just go back and flash the (recovery.img) from twrp itself and choose the path recovery and flash , after that the phone will reboot and it will go to stock recovery. Then give a wipe in the stock recovery and reboot. Now you are back to stock android 9.
Now we are in android 9 with the unlocked bootloader. That’s all.
For those who needs to lock the bootloader read the information below
Check the stock recovery version number ( if it shows rooted near the version number) if it says rooted don’t relock the bootloader. From the phone just run stock ozip again and let it boot in to os, after that again check the stock recovery if rooted string is gone. If it is gone now you are good to lock the bootloader.
Because with unlocked bootloader the google pay is not working so for me locking the bootloder is important for me , also I checked in the device info that widevine is change back to L1.
dont lock bootloader with twrp recovery

where can i get in depth test for global version ?
and did i lose the fingerprint after unlocking bootloader?

Where is the stock recovery that you attached? Can u show step by step with more detail explaination?

rhazes305 said:
Where is the stock recovery that you attached? Can u show step by step with more detail explaination?
Click to expand...
Click to collapse
Hi,
from this link i had downloaded the stock recovery of android 9, it is 54 mb zip file , after you unzip use only recovery.img
i will post properly the procedure..
https://forum.xda-developers.com/realme-x2-pro/how-to/boot-stock-recovery-boot-t4003971
download link :
https://sourceforge.net/projects/rmx1931ex-stock-files/files/RMX1931EX_11_A06_GLOBAL.zip/download

arthajudeenuk said:
Android 10 downgrade.
now the tools are available in realme website to unlock the bootloader...
install deep testing apk and unlocking the boot loader with the android 10 ( procuder will be found in realme website)
After the bootloader is unlocked......follow the procedure below..
second reboot to bootloader and flash the twrp recovery
and reboot using fastboot command itself
it will go straight to twrp recovery mode.
just give wipe data function which is default...
then flash the android 9 ozip , after that dont reboot to system
go back and flash the stock recovery from android 9 which is attached with this post and then reboot..
now you are back to android 9.
this method is working for me ..
after sitting many hours with stucked twrp recovery i just flashed the stock recovery and it get in to the device
Click to expand...
Click to collapse
Thanks, but I would also like a more detail explanation of the steps. Where to download the deep testing apk? And will fingerprint also work after unlocking bootloader?

rhazes305 said:
Where is the stock recovery that you attached? Can u show step by step with more detail explaination?
Click to expand...
Click to collapse
nightzun said:
Thanks, but I would also like a more detail explanation of the steps. Where to download the deep testing apk? And will fingerprint also work after unlocking bootloader?
Click to expand...
Click to collapse
Hi mate,
i typing the procedure in word document now and upload soon, afte unlocking the bootloader in android 10 the fingerprint is working good , it didnt affect the fingerprint because the realme didnt block it in this update.

you are the best! thanx
** sadly i cannot unlock bl coz i got error " This is carrier-customized phone" on deep testing apk.
I would appreciate it if anyone would help me to solve this problem

Is there something wrong with Android 10?
Or why downgrade to 9?

Yerry said:
Is there something wrong with Android 10?
Or why downgrade to 9?
Click to expand...
Click to collapse
- More battery long lasting on A9, perhaps more services are running in A10 rising power consumption or not well updated.
- In early versions of A10 call recording was capped due privacy rights. With the last update C.26 I can record calls but not tag the records accesing to the contacts list.
- Also in the last C.26 update of A10, you can take RAW photos in 'expert mode'.

pr0orz1337 said:
- More battery long lasting on A9, perhaps more services are running in A10 rising power consumption or not well updated.
- In early versions of A10 call recording was capped due privacy rights. With the last update C.26 I can record calls but not tag the records accesing to the contacts list.
- Also in the last C.26 update of A10, you can take RAW photos in 'expert mode'.
Click to expand...
Click to collapse
Thank you for the info.
Just upgraded, first there was an odd connectivity issue, every GPS fix loss, deactivated mobile and WiIfi for 5 seconds
After turning Smart power savings mode off and on, the issue disappeared.
About raw mode: Odd raw mode that does not save in 64 MPix

arthajudeenuk said:
Android 10 downgrade.
Check the stock recovery version number ( if it shows rooted near the version number) if it says rooted don’t relock the bootloader. From the phone just run stock ozip again and let it boot in to os, after that again check the stock recovery if rooted string is gone. If it is gone now you are good to lock the bootloader.
Because with unlocked bootloader the google pay is not working so for me locking the bootloder is important for me , also I checked in the device info that widevine is change back to L1.
dont lock bootloader with twrp recovery
Click to expand...
Click to collapse
It is possible after lock bootloader,unlock one more time?

The links on step 3 are not correct.
Can you update the post?

Yerry said:
The links on step 3 are not correct.
Can you update the post?
Click to expand...
Click to collapse
Updated ...please download from the XDA page link , downoad the firmware with stock recovery.

Thanks bro...i downgraded to color os and now it ia running smoothly..

This method works with RMX1931 (CN version)? Because i see that the recovery used in the op is for RMX1931EX

Thanks for ur help But is there a way to get a stock recovery for Chinese version ?

Are you sure that we don't have to flash vbmeta.img.because somewhere i have read that if i don't flash vbmeta my phone will be dead

will still working on CN Rom based devices?

Even after installing the ozip from phone my recovery says rooted! Anyway to change that or remove the root?