Screen brightness settings? - Nexus 6P Q&A, Help & Troubleshooting

I came from a Nexus 5 and had to always leave my screen brightness on about 1/3 in order to preserve battery. After playing with my 6P for over a month, I feel like the battery can handle a brighter setting (with my usage). But, I have concerns about burn-in if I put the setting too high since this is an AMOLED panel.
What brightness settings are you using and have you had any issues with burn-in?

I will get this started. I first started by activating the Adaptive Brightness under the display settings.
It makes the screen dimmer - to my eyes even though it sets the overall brightness to exactly half way.
I thought my whites looked somewhat grey at that setting so I turned it off and put my screen back down to 1/3 (LOL) and I am pleased with the results - especially at night as the whites look whiter.
anything past half at night burns in my retinas much less the screen.
I have not noticed any less Screen on time. I still get about 4.5 - 5 hours until it hits 15%. This is with location turned on and email push. I don't use twitter, facebook or any of those social apps the young people are using these days.

Is there an easy way to dim the screen to the point where you can't see the picture? I stream the phone in my car, which means it will get hot with charging, screen on, and high usage simultaneously. Since it is an AMOLED screen, it would not allow for screen off like other devices. Seems like without this, burn in would be a big problem for me.

I would think that you could just do the 2 finger swipe to bring it to the default menu. Then set the slider down as low as possible until you can barely see anything. I took a 5 hour drive today with my Nexus 6P with the girlfriend and had it plugged in for at least 2 hours at a time. My phone did not get really warm while either plugged or when running on battery.
Also I have enabled the System UI Tuner and now my phone screen only stays on when plugged into the power source if I select "stay on when plugged in"

mhughes1966 said:
I would think that you could just do the 2 finger swipe to bring it to the default menu. Then set the slider down as low as possible until you can barely see anything. I took a 5 hour drive today with my Nexus 6P with the girlfriend and had it plugged in for at least 2 hours at a time. My phone did not get really warm while either plugged or when running on battery.
Also I have enabled the System UI Tuner and now my phone screen only stays on when plugged into the power source if I select "stay on when plugged in"
Click to expand...
Click to collapse
No burn in issues? I would think there is a way to reduce brightness beyond stock but I don't know enough to do that at this point. Perhaps through Xposed it something.

Travillion said:
I came from a Nexus 5 and had to always leave my screen brightness on about 1/3 in order to preserve battery. After playing with my 6P for over a month, I feel like the battery can handle a brighter setting (with my usage). But, I have concerns about burn-in if I put the setting too high since this is an AMOLED panel.
What brightness settings are you using and have you had any issues with burn-in?
Click to expand...
Click to collapse
I had a gnex that I kept on low brightness and refused to get another nexus until battery was straightened out. On my dmaxx, I kept the brightness high and no burn in on the amoled. The 6p isn't as good at battery, despite being huge, but it's good enough. I keep it on 60-100 brightness, using lux to adjust it as needed. No burn in so far

Related

Auto brightness only brightens, never dims

I noticed that the brightness only brightens but never dims back in automatic brightness display setting. I can reproduce this easy with turning the lamp on my desk on and off. It only goes back to the lower brightness if turning the screen off and on again.
Noticed this too but seems to only occur when I use a widget to toggle between Auto and 100%.
If I leave the setting in Auto from within settings then it seems to work. Brightness widgets seem to break the auto functionality.
Hmm, I don't use a brightness widget. The light of the softbuttons go on if I cover the light sensor, but the screens stays in high brightness.
Strahlenkanone said:
Hmm, I don't use a brightness widget. The light of the softbuttons go on if I cover the light sensor, but the screens stays in high brightness.
Click to expand...
Click to collapse
Must be an all around bug then. If you turn the Atrix off and back on then the auto brightness functionality is restored.
Strahlenkanone said:
I noticed that the brightness only brightens but never dims back in automatic brightness display setting. I can reproduce this easy with turning the lamp on my desk on and off. It only goes back to the lower brightness if turning the screen off and on again.
Click to expand...
Click to collapse
This must be an Android thing. My Atrix does the same thing, as did the Nexus One I had before. I've had several (high end) Nokia's that dimmed/brightened perfectly. After 5 seconds, they would brighten (or dim) accordingly. I was hoping Motorola was better at making phones than HTC (the KING of bad battery life). We ALL lose here. Our precious battery life is being drained by the poor execution of a simple function.
This is a stock android thing (problem). Custom ROMs can allow it to dim and change brightness smoothly rather than in discrete steps (Cyanogen).
That's what I thought. I found this free app called "esdimmer". It supposed to be for Galaxy phones, but it's somewhat working on my Atrix. Does this function work any better in Gingerbread?
Sent from my MB860 using XDA App
Well it's good to hear that it's a stock android problem and not the actual phone. I did find a way to get around this problem but it's very limited. You can get the screen to dim by first putting the phone into standby and then press the standby button once again (which gets you into the lock screen). You'll notice that the screen then dims (if coming from a well lit area/room to a darker one).

Screen too bright, fix + save battery

Evo screen is brighter than most phones with AUTO light sensor on = more battery drain.
Just found app "screen adjuster". It works along with LIGHT SENSOR. I'm setting it to 50%. So it's half the brightness and you keep the auto sensor on.
https://market.android.com/details?...t=W251bGwsMSwxLDEsImNvbS5uZXRtYW5zbGFiLnNhIl0.
Going to try it out. I've thought the same thing for a long time. Thanks for the suggestion!
Tried this app out not sure how much battery it would save replacing the brightness with an app constantly running in the background considering it has to run 24/7 to maintain the brightness level I doubt it would save any battery if not kill it faster than the brightness level since 1. Brightness is off when screen is off but this is still running while screen is off and 2. The brightness only goes all the way up when you are in bright light so you can see the screen setting the app at 50% is really pointless since on auto the screen is at 50 - 70% when you are indoors
We are legion, for we are many
@Evil
I think your points are valid, but just wanna throw out that I think the OP is saying the baseline screen brightness is too high. At all levels.
sent from AOKP heaven
scottspa74 said:
@Evil
I think your points are valid, but just wanna throw out that I think the OP is saying the baseline screen brightness is too high. At all levels.
sent from AOKP heaven
Click to expand...
Click to collapse
It only sets Max at whatever level u set it to then autos from there, and it runs ~5mb ram constantly so it really doesn't do a whole lot it just sets, as an example, u set it to 80% with the app then on auto ur brightness goes from min to 80% and back to min or in between the two it doesn't dim all levels, and runs constantly so I would say its more trouble than its worth it would be nice if u could just set a lower Max and not need the app running 24/7
We are legion, for we are many
-EViL-KoNCEPTz- said:
Tried this app out not sure how much battery it would save replacing the brightness with an app constantly running in the background considering it has to run 24/7 to maintain the brightness level I doubt it would save any battery if not kill it faster than the brightness level since 1. Brightness is off when screen is off but this is still running while screen is off and 2. The brightness only goes all the way up when you are in bright light so you can see the screen setting the app at 50% is really pointless since on auto the screen is at 50 - 70% when you are indoors
We are legion, for we are many
Click to expand...
Click to collapse
There MANY processes constantly running in the background, the OS is smart enough to pause most of these processes when in sleep mode (display off). For example, if you use the light sensor and your phone is off the sensor is not being polled anymore.
Setting 50% means if the brightness is normally at 100 it would be 50, if it was normally 50-70 indoors it would be really be 25-35 with the app.
Or a lower baseline, which I believe is the OPs point. But yes, running an extra ap is an inefficient way to do that.
sent from AOKP heaven
mxl180 said:
There MANY processes constantly running in the background, the OS is smart enough to pause most of these processes when in sleep mode (display off). For example, if you use the light sensor and your phone is off the sensor is not being polled anymore.
Setting 50% means if the brightness is normally at 100 it would be 50, if it was normally 50-70 indoors it would be really be 25-35 with the app.
Click to expand...
Click to collapse
The app doesn't pause it runs as a notification task killers don't touch it, and it doesn't work the way u think in lower light it will stay at 50% it just prevents the screen from going past where u set it it doesn't change the values of anything in the sensor just stops the screen from going above x% so if ur in a bright room where ur screen would be at 50% and u have it set to 50% it would still be at 50% not 25%, what I'm trying to say is the app doesn't work the way its advertised
We are legion, for we are many
This was on my list of things to be fixed nearly from the start but nobody, especially devs, seemed to care.
http://forum.xda-developers.com/showthread.php?t=716547
Display brightness
Based on experience what are the optimal display settings for the best battery life?
lol 0% is the optimum setting. really, the more its off, the more you save. the less its off, the more you save. its really up to your eyes and what you can tolerate. i just have a widget, at night i flip it to 0, and during the day if i'm out doors and in doors i leave it on auto, and if i'm indoors like at work, i leave it at 25%. what sucks is i don't smoke in my apt, so when i wake up i go outside for a cig and my screen's at 0, and i'm trying to read it in the sunlight to turn it back on lol... buuuuuut, i'm sure my way saves more battery than using an app that is constantly running

Brightness all the way down = screen turning off

Anyone else seeing this?
I could have swore that on my first Nexus device (RMAed due to bad speaker), I could turn the brightness all the way down and use the tablet on the lowest setting.
On my new Nexus (no issues so far), if I turn the brightness dial all the way down, the backlight totally shuts off, causing the screen to be impossible to be seen.
I'm not RMAing this one because it's perfect otherwise, it's just very weird behavior
I got the brightness on mine all the way down & the screen isn't off.
MMcCraryNJ said:
Anyone else seeing this?
I could have swore that on my first Nexus device (RMAed due to bad speaker), I could turn the brightness all the way down and use the tablet on the lowest setting.
On my new Nexus (no issues so far), if I turn the brightness dial all the way down, the backlight totally shuts off, causing the screen to be impossible to be seen.
I'm not RMAing this one because it's perfect otherwise, it's just very weird behavior
Click to expand...
Click to collapse
Did you find a solution?
I have the same problem. If I turn down to minimum brightness (10% or less) my screen goes black. The only way I can see what's on the screen is if I shine a light, and then I can barely make out what the screen says. I assume this is an easy software fix. Also, if auto-brightness is on and I'm in a dark environment the screen will occasionally dip to the lowest setting and turn off.
I'm on my second device also. My first one had bad screen lift, flickering and occasionally screen glitches with black lines flickering through the screen. This one had no noticeable screen lift out of the box, but I'm reserving my judgement, as the device I just returned was fine for the first few hours and then got worse as I used it more.
I have both devices side by side, since Google mailed me the new one first. Comparing the two, I notice the old one's screen is slightly brighter, maybe about 10% or so, but definitely noticeable. Also my new one has a little bit of bleeding on the left side; not terrible as some pictures I've seen, but definitely there.
Update: The screen flickering returned, so I just requested a second replacement. This is actually ridiculous.

Should I Switch My S4 for Another One?

I got my S4 last week and it's great. This one doesn't have any lag, or at least not anything that concerns me. However, it does have screen issues, especially with the light adjustment. Sometimes the screen will randomly go full brightness for a second and then go back to normal, I notice this when accessing messaging sometimes. I know it also does this for Instagram, but it is suppose to do that.
Now, sometimes it seems like it does a colorshift. the screen will appear less blue and more yellow. It did this when I was accessing the facebook messenger app once and maybe another one. I might be making this up, but it just seems like the color changes ever so slightly. Also, once in a blue moon when it is adjusting screen brightness, all these vertical black lines appear for a microsecond on certain parts of the screen, it seems like an even distribution of lines. Reminds me of something old game boys might do.
I am very happy with the phone though, and I don't want to switch it if I don't have too. However, if another version might not have these issues, I want to switch ASAP, I only have a week left to swap for a new one. After that, my 14 days are up and they said they would only give me refurbs. :[
Do it.
I'm stuck with a defective screen 16GB because the 32GB did not come in on launch day which was my last day to return.
My only option at this point is to get another 16GB that's refurbished from warranty.
The irony in all this is that I manage the kiosk where I purchased the phone on my personal account.
My employees' phones and demo don't have the same screen issues I have.
Sent from my SAMSUNG-SGH-I337 using xda premium
There is a setting in accessibility that called color adjusment mess with that and see if that helps it
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
I will check out the settings. The events that this glitches happen are rare, but it has only been a week and they have happened numerous times. The auto lighting adjustment sucks, times when it should be bright it's not. Plus the black line stuff that happens sometimes. If all of them experience this I dont want to trade in for another one. I don't want to risk trading my working phone for one that won't work so well.
DuffmasterFresh said:
I will check out the settings. The events that this glitches happen are rare, but it has only been a week and they have happened numerous times. The auto lighting adjustment sucks, times when it should be bright it's not. Plus the black line stuff that happens sometimes. If all of them experience this I dont want to trade in for another one. I don't want to risk trading my working phone for one that won't work so well.
Click to expand...
Click to collapse
I would swap it if I were you.. I came from the HTC one because of repeated problems and switched to the s4... I've only had it a few days now but have only experienced some lag (fixed by tweaking settings) and the auto brightness is a little slow to adjust sometimes (I've always though this about all my Samsung devices).. But no color changing or bars appearing.. Just my 2 cents..
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
that is partially due to the type of color meter and ambient light sensor type (should be a 40-something segment black and white unless my info on the sensor specs are off. i believe apple has designed a proprietary multisegment rgb meter for theirs). b/w meters get lumens correct, but not perceived brightness (human eye is not the same as a sensor).
the color changing issue you are having may be due to the display mode being set on auto (start, settings, display mode) and under lighting that the sensor cannot correctly meter for (fluorescent lights flicker at the same hertz as your AC current, and are actually pretty dim and WAY off for color balance, so that SHOULD throw the sensors off continuously, which would lead to auto brightness hunting and inaccurate selection of the 'correct' color mode).
try turning auto brightness off and color mode to professional photo or movie (i use move as its very flat and closer to real colors). there ought to be a way to trick the ambient brightness sensor to sample and average at a faster rate, and ramp up/down more smoothly, but i cant code for android otherwise i would have been working on one.
i work in tv/film industry on the sensor/lighting side btw. if the issue goes away, turn on auto brightness and check it out under NON FLUORESCENT lighting. if its gone, it was probably the display mode changing along with auto brightness.
Please read forum rules before posting
Questions and help issues go in Q&A
Thread moved
Thank you for your cooperation
Friendly Neighborhood Moderator
Slade8525 said:
that is partially due to the type of color meter and ambient light sensor type (should be a 40-something segment black and white unless my info on the sensor specs are off. i believe apple has designed a proprietary multisegment rgb meter for theirs). b/w meters get lumens correct, but not perceived brightness (human eye is not the same as a sensor).
the color changing issue you are having may be due to the display mode being set on auto (start, settings, display mode) and under lighting that the sensor cannot correctly meter for (fluorescent lights flicker at the same hertz as your AC current, and are actually pretty dim and WAY off for color balance, so that SHOULD throw the sensors off continuously, which would lead to auto brightness hunting and inaccurate selection of the 'correct' color mode).
try turning auto brightness off and color mode to professional photo or movie (i use move as its very flat and closer to real colors). there ought to be a way to trick the ambient brightness sensor to sample and average at a faster rate, and ramp up/down more smoothly, but i cant code for android otherwise i would have been working on one.
i work in tv/film industry on the sensor/lighting side btw. if the issue goes away, turn on auto brightness and check it out under NON FLUORESCENT lighting. if its gone, it was probably the display mode changing along with auto brightness.
Click to expand...
Click to collapse
I had no idea the S4 had these options. I guess I am used to my Atrix which didnt do much. I went in and adjusted the settings. The auto screen brightness never really did a good job, I feel that it is way too dim in situations where it should be brighter. I will text your advice the next week and see what happens. If I still get issues, I will return it as I have one week left of my 14 days. Thank you very much for the excellent advice!
DuffmasterFresh said:
I had no idea the S4 had these options. I guess I am used to my Atrix which didnt do much. I went in and adjusted the settings. The auto screen brightness never really did a good job, I feel that it is way too dim in situations where it should be brighter. I will text your advice the next week and see what happens. If I still get issues, I will return it as I have one week left of my 14 days. Thank you very much for the excellent advice!
Click to expand...
Click to collapse
no problem; the auto brightness on the GS4 is only slightly better than the Atrix 4G (had one too), and same as the GS3. The color mode thing (which is awesome; closer to real life colors versus waaaay oversaturated screens on most phones. also check power saving settings.
also see this thread
http://forum.xda-developers.com/showthread.php?p=41616076#post41616076
Well, I have not seen those black lines since I turned off auto brightness and turned off the screen automatically doing it's own color adjustments. I will turn these back on to see if I can duplicate the issue. I do feel that I have more lag now, but I could just be paranoid.
OK, when I am using my Facebook Messenger App, sometimes these black lines appear horizontally across the screen on low brightness. However, sometimes they dont. I dont want to call them black lines, but maybe I should say they are ghostly tv lines that are barely noticeable. Ideas?
Could someone explain the defective screen issue?, mine looks great...
The phone works great most of the time and is totally useable, the only issue is that sometimes it does these weird things as I have explained. Tomorrow is the 14 day mark, so I am having a hard time deciding if I should switch for another one just in case, or assume all of this is normal and hope the phone lasts me 2 years.
DuffmasterFresh said:
The phone works great most of the time and is totally useable, the only issue is that sometimes it does these weird things as I have explained. Tomorrow is the 14 day mark, so I am having a hard time deciding if I should switch for another one just in case, or assume all of this is normal and hope the phone lasts me 2 years.
Click to expand...
Click to collapse
Could possibly be a GPU issue. Have you had any problems playing heavy duty 3d games?
Sent from my GT-N7100
No problems playing the Iron Man 3 game, everything seems fine.
It seems like any time the keyboard is pulled up, the screen shifts color to something more yellow. all of the keys go from a nice grey to a off grey yellow tint color. During this transition, I can literally see the screen transition as weird lines appear for a fraction of a second, like switching channels on an old TV. I tried recording this on my DSLR 1080P camera but it could not pick up the color change visibly. I might try again. It does this on Google Chrome, Facebook Messenger, Snap Chat even. sometimes it color shifts even when the keyboard is not involved. I have the auto adjustments on the screen off and the color set to Standard Mode.
The ATT store said I am a day out of my 14 day limit and there is nothing they can do. They said I have to talk to warranty and see if they will be nice enough to send me a new one. I dont want a refurb, last time that happened, I went through 4 of them. I talked to ATT support and they said they would extend my 14 days another 3 days but the ATT store said I was out of luck for an exchange for a new phone.
So no one elses screen color shifts to yellow when the keyboard pops up? Mine does this now all the time, mainly in low light. It might do it in all light situations but in sunlight I prolly just can't see it. It's incredibly annoying because the screen itself wacks out every time it does it.

Screen brightness when wirelessly charging?

I have a wireless charging cradle that I put my G6 on overnight. It's allowed me to get rid of my old school alarm clock. The problem is that the time display is a little too dark for my tastes. I don't want it bright and blaring but a little bump would be nice.
For comparison, my wife has a Galaxay S8 with the same charger on her side of the bed and hers is brighter and easier to read without being obnoxious.
I do not use the always-on display during the day but have it set to come on between 10pm and 6am which is typically when I'm in bed and the phone would be charging.
I looked but do not see a way to adjust the brightness of the always on display nor do I see a setting to bump up the brightness while on charge. Am I missing it?
No specific option to increase brightness while charging. You can enable "brighter" AOD in the AOD options menu, but it basically prevents the AOD from dimming too much. You can use an app like Lux to adjust things like this.
Sent from my LG-H872 using Tapatalk

Categories

Resources