Related
hey guys is will need some help with this device im not kind of a noobie on this kind of things bcs i been working with several phones, like the veteran xperia10, galaxy ace, motoroi2, etc etc. but never with a tablet
here is what it happens a friend ask me if i can upgrade his sgt-p1010 to a newer version, honeycomb or maybe ics, i´ve read a lot of posts regarding this on how to upgrade it trough odin everything was fine until the reboot of the device, bcs by my mistake i flash a rom of the 7.7" tab and this one is a 7" only now the tab is not turning on, odin is not recognizing it, either samsung kies or the pc. buttons are not responding it wont charge and cant enter to download mode.
I REALLY NEED HELP FROM U GUYS, HOPE U CAN HELP ME
ps. srry for my english :laugh:
This kind of thing can result in the inability to boot which can only be repaired by the use of specific hardware, i.e. this could be a "hard brick". Then again, maybe it can be restored to working order by flashing it again (a "soft brick"). So the very first thing you need to know is, can it get to download mode?
Turn it off, if it's switched on, and charge it for a couple of hours,say four hours. Use the original charger connected to mains. It doesn't matter if it shows anything, or nothing on the screen, let it charge. This is to make sure flashing it won't fail because it doesn't hold a charge.
Now connect it to the PC with the original USB cable. Then after making sure it's switched off, switch it on by pressing the On/Off button, while simultaneously the Volume UP switch. Press them both at the same time, and keep them pressed! If you're lucky you'll get the yellow graphic with the download text. A phone symbol, an !, and a PC symbol is fine too. Even if it doesn't show anything, you may be in download mode, so install the right drivers, and hopefully Odin or Heimdall will recognise is, and will allow you to flash the right ROM.
well i already let it charge for all night long and nothing happens after i perfomed the flashing the screen was totally in black but it doesnt shoes anything i mean the tab was turned on, then apparently batterie dies and after that is not charging. already tried with the heimdall thing but it says that device is not connected.
I think that this is going to be a HARD BRICK
so do u thhink there is another way to solve it?????
or it will be necessary the JTAG stuff???? bcs i dont want to try that it seems that is very difficult to me bcs i dont know nothing about hardware jejejeje
You have installed the Heimdall driver? It's called zadig.exe. Then you have to go to download mode and connect the Tab to the PC with the USB cable. Then Heimdall hopefully will detect the Tab.
If there's no way software will revive the Tab, it's hard bricked and will need hardware to get it working again. There's this guy mobiletechvideos.com who will repair any kind of brick. Basically he uses the JTAG on the board of the Tab and a special box to flash the right ROM to the Tab, even when it's dead. Some here have tried the service, and they say he's quite reliable. Another way is to modify your Tab with Adam Outler's Unbrickable Mod. It's brilliant, you can't soft brick your Tab after that, but it involves soldering very small components on the board of the Tab. The mobiletechvideos guy can do it for you I believe.
Well, I guess you just got a hardbrick .
The only way to fix this problem is go to SAMSUNG SERVICE CENTER.
Sent from my GT-P1000 using xda app-developers app
Hi, i want to fix a phone of my friend by flashing it with odin, but things go wrong, the phone after failing wont start or respond to any button, i dont know what to do, please any help would be appreciated
Samsung Galaxy J1 SM-J100H
Edit:
Thanks xEmre66 for your reply, unfortunately no, i think i break the boot image, the phone wont boot on download mode even if i use 300k jig, i think the only solution is to use an sd card filled with the boot image, but i dont find in website a solution like that.
I tryed many solution but no one work, please if someone have the some problem tell me.
Can you get into the DownloadMode? (ODIN MODE)???
Sent from my SM-J100H using XDA-Developers mobile app
---------- Post added at 08:58 AM ---------- Previous post was at 08:57 AM ----------
I have this phone but it is not my main phone but maybe I can help you.
Sent from my SM-J100H using XDA-Developers mobile app
i'm working on this problem..
i resolved,
share there
OSKCHAST said:
i resolved,
share there
Click to expand...
Click to collapse
Please can you share the solution ?, i cant fix the phone.
same problem here
I have same problem here, samsung j100h of my friend do not boot, i download odin and correct rom to flash i flashed device correctly, but device now is fully dead, display not start, black screen, my win10 not recognise device, now cant flash using odin and using sp_flashtool....
device respond at win10 when i push vol up + power but can't make anything
i try to install all drivers signed and unsigned from samsung and mkt.. nothing works any idea???
caseres84 said:
I have same problem here, samsung j100h of my friend do not boot, i download odin and correct rom to flash i flashed device correctly, but device now is fully dead, display not start, black screen, my win10 not recognise device, now cant flash using odin and using sp_flashtool....
device respond at win10 when i push vol up + power but can't make anything
i try to install all drivers signed and unsigned from samsung and mkt.. nothing works any idea???
Click to expand...
Click to collapse
You broke the boot image. I'm sorry but you hard bricked the device. I had this phone but it was terrible because of its touchscreen. Maybe I could help you. Send me a PM and describe how you really broke the device.
xEmre66 said:
You broke the boot image. I'm sorry but you hard bricked the device. I had this phone but it was terrible because of its touchscreen. Maybe I could help you. Send me a PM and describe how you really broke the device.
Click to expand...
Click to collapse
same in here. I flash original rom from sam mobile site and my samsung sm-j100h is bricked now. i flash using odin and everthing was ok and it was pass. but nothing happend later on, screen remains black and I don't know what to do.
or atleast tell me can I get somehow all data stored on phone, if yes how to do it
guys still nothing???
same problem guys i bricked the phone 2 days ago with the original firmware from sam mobile u.u i put my samusung j1 in download mode and with odin i done the reflash odin it was green and said me passed but then when i tried to turn on the phone nothing happened my phone is died hard bricked is there a guys something to do to repair him?
i got the same problem..
the phone was completely DEAD after i followed all the instructions here => https://www.youtube.com/watch?v=1T9fxno2s68
Please somebody help us..
Here's my thread => http://forum.xda-developers.com/android/help/help-sm-j100h-dead-power-flash-t3511894
Thank you very much..
im using sm j110h and i too flashed orginal stock rom via odin but unfortunately i forget to put the batteries on and i fonud that after that i got pass message only now the screen remaines black and not getting to download mode and not switching on. does anyone help me on this problem hope will get a solution thanks in advance
Gal J1 of sadness.... but still hoping
2 days ago a friend asked me to fix his J1 stuck in boot image. I gladly said yes for I've done it 4x already different units same model with satisfying results. This one is the exact opposite because after flashing with Odin and getting the Passed result, the phone didn't reboot. Actually it never booted right after that moment. System didn't recognize the phone not even a dim light or blink or any reaction from it even when plugged in a wall charger. tried all possible solutions even the galaxy tab procedure of total batt drain and so on. The firmware I got is from xda, J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware.zip, and I'm sure it's fine because I've used it already with good results...
Guys, any of you with a solution on this or any suggestions would be much appreciated... Thanks very much in advance!!! :fingers-crossed:
Chrisjopett said:
2 days ago a friend asked me to fix his J1 stuck in boot image. I gladly said yes for I've done it 4x already different units same model with satisfying results. This one is the exact opposite because after flashing with Odin and getting the Passed result, the phone didn't reboot. Actually it never booted right after that moment. System didn't recognize the phone not even a dim light or blink or any reaction from it even when plugged in a wall charger. tried all possible solutions even the galaxy tab procedure of total batt drain and so on. The firmware I got is from xda, J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware.zip, and I'm sure it's fine because I've used it already with good results...
Guys, any of you with a solution on this or any suggestions would be much appreciated... Thanks very much in advance!!! :fingers-crossed:
Click to expand...
Click to collapse
PM me pls and tell me how you flashed it etc.
Help
I have same problem,hard brick.Can anyone help?
somebody got solution? i did update by kies and now the phone is dead at all. i can use odin mode and also can using recovery anymore. hmm i think my problem come from the battery :crying:
kkq29 said:
somebody got solution? i did update by kies and now the phone is dead at all. i can use odin mode and also can using recovery anymore. hmm i think my problem come from the battery :crying:
Click to expand...
Click to collapse
Can you get into Odin Mode? If yes, flash the stock firmware of your region (here is a fast server which provides very fast downloads: fw.updato.com) If no, then you should change your battery as you're saying "it came from my battery" and try the first step again.
If it doesn't help as expected, then your phone is hard bricked and can't be repaired at all. The only solution would be changing the motherboard, but I would not waste my money on a low-end device motherboard and I would directly buy a new phone. :/
Regards,
xEmre66
If I am correct...
Then SM-J110H have Spreadtrum SC7727S
Here is Pinout for Direct eMMC...
https://postimg.cc/image/ul680l5jv/
This Pinout seems also to work with:
Code:
SM-G318HZ
SM-Z130H
I have leaked SM-Z130H PDF... where Instruction is inside to repair with tweezer... USB cable + Spreadtrum Tool:
Code:
[B]ResearchDownload[/B]
In theory something similar should be possible with SM-J110H...
I have at the moment only 1 problem... to create PAC file...
No idea from where I can get:
Code:
FDL1
FDL2
Best Regards
Edit 1.
Sorry, seems I was drunken...
It is sooo hard to find Posts or Threads about SM-J110H...
But it seems SM-J100H also Spreadtrum device...
xEmre66 said:
PM me pls and tell me how you flashed it etc.
Click to expand...
Click to collapse
PM me too please
My teacher phone has a same problem, hehehe.
same problem here. my phone got stuck up with samsung logo then i just dowloaded a firmware on sammobile and i flash it via odin at first it passed then my phone did'nt turn on anymore.
J100H / DD Finding Deadboot solution
Hi ... guys me too having this sort of problem and i found bad about samsung using 32bit - Spreadtrum SC8830A EMMC chipset here
Fix solution Not Found still! if i done i will tell you!
on = SM-J100H/DD --- corp =samsung yateley, uk
ok friend iam searching for Solution for 3days bt i found none= with a clue
It is J100H on serial port= SPRD U2S Daig (ComXX) usb says= SPRD COM Emumerator
this means - all sprd flashing been done on this 2 port only - in Miracle Box it says -
Scanning USB Serial port...
SU2Serial Port: COM64
Connecting to Phone,Wait..
Done.
Infor: SPRD3
Initialize boot19...
>>BootLoad Error. ID: 1
so my option is if we build a sprdp.bin and flash in AP(PDA) it will boot to Download mode
and dont ask me where is that file i dont no - if any one can provide a real backup pit.pit file
via phone to me i can find something and let u know it. Only from a alive phone J100H/DD
plz friends i need help any dumps or pit. and if any one has a alive J100H/DD please tell me.!
so i can get some help from u --If you wish to help
somedays ago, i rooted my samsung galaxy grand prime (sm-g531f). which is processed by flash twrp via odin, & then flash supersu via twrp recovery.
after root, i erroneously add google account, so that frp lock was on. and top of that when i go to recovery mode its shown "custom binary blocked by frp".
so, solve this problem (bcoz i already solve this many time on many phone), i go to download mode, and i try to connect my phone via usb cable in pc, but everytime it say "usb device not recognized", but when my phone was switched on (before locked by frp), it also not recognized by usb but it was charging..
so, now:
*i cant switch on my phone
*cant go to recovery mode
*cant connect by usb cable
*i tried on many usb cables
*two laptops
*install/unistall samsung mobile drivers many times
but, nothing wasnt solved my problem..
if anyone also faced this problem, and solved this, please share your valuable process in this thread.. and help me...
Update-1: now i even change my phone's usb connector if anything could happen, but again my bad luck.. nothing happen, means usb not recognized..
Update-2: sorry i was offline or forgot to update my condition. I was tried to fix it via many mobile hardware technichian. And at last, i fixed my problem by change my whole motherboard. Bcoz, the all technichian told me that, it was my phone's cpu which have problem. For that, it couldn't recognize by any pc.
Do u have another samsung phone? If yes then try this connect that phone to your laptop or pc let it be recognised anf when thatd done removed the port from that phone and immediately connect your phone in download mode. This worked for me. If that doesnt work tell me ill look for another solution
waleeds1 said:
Do u have another samsung phone? If yes then try this connect that phone to your laptop or pc let it be recognised anf when thatd done removed the port from that phone and immediately connect your phone in download mode. This worked for me. If that doesnt work tell me ill look for another solution
Click to expand...
Click to collapse
bad luck, its not worked for me...
aamnahid said:
bad luck, its not worked for me...
Click to expand...
Click to collapse
This might be stupid but try it worked for many people. Boot your phone in download mode connect it to your pc open odin and without removing the cable remove the battery of your phone. Your screen wont go off , and if odin recognizes your phone put the battery back. It might not work but still give it a try
waleeds1 said:
This might be stupid but try it worked for many people. Boot your phone in download mode connect it to your pc open odin and without removing the cable remove the battery of your phone. Your screen wont go off , and if odin recognizes your phone put the battery back. It might not work but still give it a try
Click to expand...
Click to collapse
this was also not worked...
I have the same problem and my battery is built in unfortunately any suggestions please
Abdul.82 said:
I have the same problem and my battery is built in unfortunately any suggestions please
Click to expand...
Click to collapse
I'm having this exact problem also. I've downloaded usb drivers for Samsung, i've downloaded kies, ive tried 5 different computers and 4 different cords. No computer even recognizes it (but it does charge) and only one computer says couldn't recognize usb device.
Currently i'm stuck in the google loop of trying to login with an ID that you've previously used on this device and when i enter in the correct info it just keeps looping back to that screen, so i cant even get into the phone to debug or choose MTP connection etc.
The only reason i pulled out the grand prime and started working on it, was i rooted my s6 and s5 and i wanted to keep learning so i pulled out the grand prime and realized its powerful enough to run updated software so it doesn't have to be a paperweight anymore.
Me too I have same problem bro plz help me
FIX for FRP LOCK USB Not Working
The only way to fix that I have gotten to work is to download the stock firmware and Flash using ODIN. I had to try a few different cords but it will eventually work!! Keep trying!! I did the BL the AP the CSC and the CP, went into download mode and ONLY STOCK FIRMWARE works ok!
---------- Post added at 09:51 PM ---------- Previous post was at 09:49 PM ----------
DionWhite33 said:
The only way to fix that I have gotten to work is to download the stock firmware and Flash using ODIN. I had to try a few different cords but it will eventually work!! Keep trying!! I did the BL the AP the CSC and the CP, went into download mode and ONLY STOCK FIRMWARE works ok!
Click to expand...
Click to collapse
it took me a few minutes to figure this out after flashing Root with CF auto didnt work nor did TWRP. So I tried the Samsung Smartswitch and no luck..
hi ,did you find a solution to the frp lock and usb not recognising?
Soo i accidentally disabled the dev options on my samsung galaxy s7 edge and then decided to restart my phoe because i didnt notice and now im stuck with an error that says "custom binary blocked by FAP lock" now i looked around the internet on ways to fix this but the thing is that i cant really connect my phone to my computer, yes i did the volume down+power+home button thing and i connected it to my pc but nothing happened, odin didnt recognize my phone and my computer reads it as "gadget serial" i tried installing the usb drivers and all but i keep getting errors, its like my phone doesnt realy wants to cooperate.
Anyways i was wondering if any of you could help me with this please, i beg of you if anyone has an answer im willing to try, also if you need more info just ask, ill be glad to provide, thanks!
Anyone?...
Well i managed to fixed it so heres the solution for all of you that may come across this,
Soo basically make sure youre pc is fully updated, it must have all window drivers installed (i used windows 10) all window updates, make sure all the pieces of your pc are updated and then connect your phone and for the love of god be patient
I take it this is you're first time encountering something like this... at any rate, welcome to the forums.
Hello everyone, so here i am trying to flash a friend's a1000, but unfortunately, i'm unable to do so because when i try to enter the bootloader by holding the volume up key before plugging in the usb cable to start the process, it only connects to the computer for about 9 seconds, and then automatically disconnects, i get a coloured screen afterwards, and i would be forced to restart the device, i first suspected that it was the cable, but i was wrong, since i've already tried a bunch of cables, all with the same exact result, i also used 3 different computers, and i still got the same result, please respond if you have any idea.
Sisine said:
Hello everyone, so here i am trying to flash a friend's a1000, but unfortunately, i'm unable to do so because when i try to enter the bootloader by holding the volume up key before plugging in the usb cable to start the process, it only connects to the computer for about 9 seconds, and then automatically disconnects, i get a coloured screen afterwards, and i would be forced to restart the device, i first suspected that it was the cable, but i was wrong, since i've already tried a bunch of cables, all with the same exact result, i also used 3 different computers, and i still got the same result, please respond if you have any idea.
Click to expand...
Click to collapse
you need drivers to flash it. i flashed mine in september 2021 and most drivers didnt work. i ended up getting drivers with the same name for a diffrent phone and the flash worked. so try doing that it might end up working. i dont how i did it but it was really hard
Vuk1152 said:
you need drivers to flash it. i flashed mine in september 2021 and most drivers didnt work. i ended up getting drivers with the same name for a diffrent phone and the flash worked. so try doing that it might end up working. i dont how i did it but it was really hard
Click to expand...
Click to collapse
You're right, it is hard indeed, i've already tried so many drivers, i think i'm giving up lol, thanks a lot for the reply, i really didn't expect one since that specific phone is ages old by now !
Sisine said:
You're right, it is hard indeed, i've already tried so many drivers, i think i'm giving up lol, thanks a lot for the reply, i really didn't expect one since that specific phone is ages old by now !
Click to expand...
Click to collapse
thanks. i replied this cause i have the same phone which i want to custom rom but there arent any roms available.(if you have any roms, please let me know)i can try to find you the youtube video i used for the drivers if you tell me what they are called. (if you want to xd) i think its something like "mediatek drivers"
Vuk1152 said:
thanks. i replied this cause i have the same phone which i want to custom rom but there arent any roms available.(if you have any roms, please let me know)i can try to find you the youtube video i used for the drivers if you tell me what they are called. (if you want to xd) i think its something like "mediatek drivers"
Click to expand...
Click to collapse
I appreciate that, i'll let you know if i find a compatible rom for the device, i think the drivers are called CDC drivers if i remember correctly, i don't have the files, but i'm almost sure it's CDC, i'll be grateful if you can send me a link to that video.
Sisine said:
I appreciate that, i'll let you know if i find a compatible rom for the device, i think the drivers are called CDC drivers if i remember correctly, i don't have the files, but i'm almost sure it's CDC, i'll be grateful if you can send me a link to that video.
Click to expand...
Click to collapse
i dont think i ever used that cdc thing when flashing that phone. im pretty sure i used https://firmwarefile.com/lenovo-a1000 to get the stock firmware and just searched up "(driver name) download" on youtube and used some indian guys tutorial. you can try this video if you havent alredy (for the cdc driver)
Vuk1152 said:
i dont think i ever used that cdc thing when flashing that phone. im pretty sure i used https://firmwarefile.com/lenovo-a1000 to get the stock firmware and just searched up "(driver name) download" on youtube and used some indian guys tutorial. you can try this video if you havent alredy (for the cdc driver)
Click to expand...
Click to collapse
I'll try that one, thank you.
Sisine said:
I'll try that one, thank you.
Click to expand...
Click to collapse
np
Do you guys still have the files?
I managed to get the proper drivers and the phone is seen by the computer and I manage to flash it , but the phone is completly dead after the flash .
The power button wont do anything, plugging it into the charger doesnt do anything, I can only reflash it by connecting it to the pc while holding the volume up & down buttons.
Checking on old forums, aparently there are two versions of the phone , single sim and dual sim.
Also the revision number seems to be important for some reason, so mines is dual sim , revision 61 .
I believe this was the firmware that was on it previously, although the phone remained stuck at the boot logo : a1000_usr_s29798_1511241708_sprd7731_ro , but i cant find it anywhere , so I flashed the one you guys had , but now the phone is a dead brick after the flashing ends . Nothing on the screen, no response from any of the buttons, just dead.
CurlyBlonde said:
Do you guys still have the files?
I managed to get the proper drivers and the phone is seen by the computer and I manage to flash it , but the phone is completly dead after the flash .
The power button wont do anything, plugging it into the charger doesnt do anything, I can only reflash it by connecting it to the pc while holding the volume up & down buttons.
Checking on old forums, aparently there are two versions of the phone , single sim and dual sim.
Also the revision number seems to be important for some reason, so mines is dual sim , revision 61 .
I believe this was the firmware that was on it previously, although the phone remained stuck at the boot logo : a1000_usr_s29798_1511241708_sprd7731_ro , but i cant find it anywhere , so I flashed the one you guys had , but now the phone is a dead brick after the flashing ends . Nothing on the screen, no response from any of the buttons, just dead.
Click to expand...
Click to collapse
sorry, i deleted my lenovo a1000 files to focus on other phones. from what i have heard that issue is common with that phone. i know someone who flashed the firmware on their a1000 and got stuck in the same issue as you. i tried to help them unbrick it but it seems to be impossible. i think you need to do a board replacement if you want to use that phone again. also, i dont think that the phone revisions are that important cause i managed to get lenovo a1000m firmware on my lenovo a1000.