When I restore by Odin my N910H 5.1.1
my Note 4 is hanging SW REV CHECK FAIL DEVICE 2 BINARY 1
Please help!
khongchinhxac said:
When I restore by Odin my N910H 5.1.1
my Note 4 is hanging SW REV CHECK FAIL DEVICE 2 BINARY 1
Please help!
Click to expand...
Click to collapse
pharhaps you have tried to restore downgrade version. plz try to the latest software version.
khongchinhxac said:
When I restore by Odin my N910H 5.1.1
my Note 4 is hanging SW REV CHECK FAIL DEVICE 2 BINARY 1
Please help!
Click to expand...
Click to collapse
i have the same problem...please!!! help me!!!
Probably you've had an OTA (over the air, wifi) update. You should flash latest firmware for your device. Samsung locked the bootloader, it's not possible to install an older firm anymore (until someone finds how).
any solution to fix this problem ?
Any solution to this?
Looking for a solution!!!!
Nixdax said:
Looking for a solution!!!!
Click to expand...
Click to collapse
I fixed my phone by downloading stock 5.1.1, unpacked with 7zip, deleted modem.bin and sboot.bin from the extracted contents, packed the contents again as tar using 7zip and flashed via ODIN.
Looking for an answer as well. Same situation after I wiped cache. Phone is on the fritz. Ive been up for the past 6 hours trying to fix it. Im trying to save my files on my phone in the case I need to wipe everything.
theplagueisback said:
I fixed my phone by downloading stock 5.1.1, unpacked with 7zip, deleted modem.bin and sboot.bin from the extracted contents, packed the contents again as tar using 7zip and flashed via ODIN.
Click to expand...
Click to collapse
do you mean aboot.bin? and when you packed the contents, did you just zip them? then just the extension to .tar? or did you change it to .tar, THEN zip it?
Figured it out on my own. Flashed CF autoroot. Then flashed 5.1.1 which is the most up to date firmware. Im not sure if the issue was because I was doing 5.1.0 and didnt realize that was the most UTD version, or if CF to 5.1.1 was the trigger. Either way, it worked.
I tried this but also failed, then I read somewhere else that I need to remove cm.bin and sboot.bin.
I did and it flashed OK, but phone is stuck in bootloop and wont go to recovery mote form e to reset.
I am presently searching for a way to get it out of bootloop
dannyogolo said:
I tried this but also failed, then I read somewhere else that I need to remove cm.bin and sboot.bin.
I did and it flashed OK, but phone is stuck in bootloop and wont go to recovery mote form e to reset.
I am presently searching for a way to get it out of bootloop
Click to expand...
Click to collapse
try rename firmware file from .md5 to .tar and extract it using 7-Zip, delete or move sboot.bin and modem.bin then make a new 7-Zip archive with .tar extension and install it regulary by Odin
Thanks.
But like I wrote, I have been able to flash, but phone is in bootloop now
use the sboot and modem files from the LATEST update..just swap em out
Related
Guys,
I really need the pit file to flash the lollipop firmware.... I get error in odin.
Someone plssss
liobeir said:
Guys,
I really need the pit file to flash the lollipop firmware.... I get error in odin.
Someone plssss
Click to expand...
Click to collapse
Pit files are really "last resort" situation. What error are you getting?
What version of odin are you using?
What model of the note4 do you have?
What happened in the first place that got you here?
Have you tried to search for a fix?
What have you tried?
More info is needed mate.
Im also on the hunt for a PIT file. I had to use one on my 9505 a few times after a brutal softbrick/almost hardbrick to recover it.
N910F
andrewwright said:
Pit files are really "last resort" situation. What error are you getting?
What version of odin are you using?
What model of the note4 do you have?
What happened in the first place that got you here?
Have you tried to search for a fix?
What have you tried?
More info is needed mate.
Click to expand...
Click to collapse
Well I was trying to flash twrp trough the twrp app. But it failed. And when I wanted to reboot in recovery.. All my phone could do was boot in download mode. So I looked for the latest lollipop firmware from Samfirmware and got an error in odin. Something about the size is too big. 85098<125876 and odin said something about exfat hidden (I'm not really sure anymore). I got my phone back to work by flashing a random pit file I found on my pc. Definitely not a note 4 pit and it failed but for some reason it rebooted back to my 4.4.4 rom as it was before I bricked it. Strange. Cause odin was almost at the end of its flash so I assume some things were flashed...
Odin version 1.83 I guess but I tried it also with 3.04 and same error
I have nite 4 sm-N910F
Searched for a pit file but as I said it was fixed by a failed flash of 4.4.4 original firmware trough odin with a totally different pit file. For some reason it booted up again. So now my phone is back... If I put it manually in download mode... Will I have the same error? Cause yeah it's not bricked... See?
Sent from my SM-N910F using XDA Free mobile app
What that app did was wipe you're recovery... All you would of had to do was flash a twrp/cmw/PHILZ recovery.
liobeir said:
Guys,
I really need the pit file to flash the lollipop firmware.... I get error in odin.
Someone plssss
Click to expand...
Click to collapse
No you really need to read the Forum Rules...moved out of the Development sections.............
hello xda community! that's my first question, plz help me solve this problem, when i intended to root my note 4 on lollipop 5.1.1 by cf auto-root with odin the phone suddenly stucked and was keeping restart by itself, i wiped cache and dalvik cache and deleted all its data and made a factory reset with no result i tried to install stock 5.1.1 again by odin and it always says failed! i'm installing Philz recovery but when i enter recovery mode it says recovery is not seandroid forcing , i'm sure i downloaded the correct firmware package so plz help me how can i fix this problem and bring my phone back to lyf??
For anyone who faces that error, just wanted to share what i made with you. The error happens due to bootloader and modem, just download the correct stock firmware for the device, rename it from .md5 to .tar and extract it using 7-Zip, delete or move sboot.bin and modem.bin then make a new 7-Zip archive with .tar extension and install it regulary by Odin :cool
I seen on other forums you can basically create a working PIT (Partition Information Table) From a Working Device, obviously based on the Same Firmware set you are running, now that root is up and running, the idea is which mmcblk to dd to get it done
Here is a link for reference I found on older Galaxy Models, id assume the process is the same but again not sure about whick block device i need to copy
Pit File Extraction
Nvr Mind Found the pit file in the CSC Section of the Stock FLash Files, doesnt exactly tell me how to generate my own but does provide a working solution if ever needed
Please CLOSE
Wildcat2083 said:
I seen on other forums you can basically create a working PIT (Partition Information Table) From a Working Device, obviously based on the Same Firmware set you are running, now that root is up and running, the idea is which mmcblk to dd to get it done
Here is a link for reference I found on older Galaxy Models, id assume the process is the same but again not sure about whick block device i need to copy
Pit File Extraction
Nvr Mind Found the pit file in the CSC Section of the Stock FLash Files, doesnt exactly tell me how to generate my own but does provide a working solution if ever needed
Please CLOSE
Click to expand...
Click to collapse
Did you ever extract the PIT file? I need one to fix my phone and I'm on the latest update that came out a few days ago. I don't have root and my S7 is stock.
CrossBones3129 said:
Did you ever extract the PIT file? I need one to fix my phone and I'm on the latest update that came out a few days ago. I don't have root and my S7 is stock.
Click to expand...
Click to collapse
I have one for the PE1 build but not for the latest fw update, however 8f you need the PE1 I can pm it to you, you might try odin and reflash the build im on it includes the pit file as well
Wildcat2083 said:
I have one for the PE1 build but not for the latest fw update, however 8f you need the PE1 I can pm it to you, you might try odin and reflash the build im on it includes the pit file as well
Click to expand...
Click to collapse
I'm on PF2. I've never used a pit file with ODIN so what does it do exactly? Could you maybe help me?
I'm getting an error when rebooting in recovery saying "failed to mount /data (Invalid arguement)". I can't notice it affecting anything though. It only pops up after I select power off, reboot, or wipe cache. If I do a wipe data/cache and thrn reboot it doesnt pop up. My phone still seems to perform right but this error worries me.
Like I said, I've never tried to root or flash my phone but this is happening.
Wildcat2083 said:
I have one for the PE1 build but not for the latest fw update, however 8f you need the PE1 I can pm it to you, you might try odin and reflash the build im on it includes the pit file as well
Click to expand...
Click to collapse
I've downgraded to PE1 seeing if that what fix my issue, but it didn't so if you do have the PE1 version that would be fine for now while I'm on this version.
CrossBones3129 said:
I've downgraded to PE1 seeing if that what fix my issue, but it didn't so if you do have the PE1 version that would be fine for now while I'm on this version.
Click to expand...
Click to collapse
if the stock files don't work i can extract a master PIT file from the phone but i need to make sure it covers all of the relevant partitions first, basically preventing you from getting an erroneous file, as they lay out how the phone should partition the emmc chip basically acting as a flash memory version of a hard drive
Wildcat2083 said:
if the stock files don't work i can extract a master PIT file from the phone but i need to make sure it covers all of the relevant partitions first, basically preventing you from getting an erroneous file, as they lay out how the phone should partition the emmc chip basically acting as a flash memory version of a hard drive
Click to expand...
Click to collapse
Sent you a PM. Your stock files had the same error as the other stock files.
Sent from my SM-T377V using Tapatalk
did you ever get the pit file for your verizon galaxy s7?
Hi, did you ever get the pit file for your galaxy s7, I need it if you did.
CrossBones3129 said:
Sent you a PM. Your stock files had the same error as the other stock files.
Sent from my SM-T377V using Tapatalk
Click to expand...
Click to collapse
Hello everyone I'm having a problem, I'm trying to put the stock firmware back on my Samsung but Odin keeps failing.
Saying '' Complete write failure'' What do I need to ?
Thanks for the help everyone!
I have the same problem. I've downloaded and tried many firmware, i even tried to use Heimdall to flash firmware, but aboot.mbn fails to flash. Please help what to do...
john.reyes.jmr said:
I have the same problem. I've downloaded and tried many firmware, i even tried to use Heimdall to flash firmware, but aboot.mbn fails to flash. Please help what to do...
Click to expand...
Click to collapse
extract the tar package and make another tar package with only system, boot and recovery related content from that original tar . It worked for me. I too was failing on aboot.mbn .IT will most likely work unless you are trying to upgrade/downgrade your phone. Downgrading is not going to work for sure. About upgrading I am not sure.
adarshadhungel1 said:
extract the tar package and make another tar package with only system, boot and recovery related content from that original tar . It worked for me. I too was failing on aboot.mbn .IT will most likely work unless you are trying to upgrade/downgrade your phone. Downgrading is not going to work for sure. About upgrading I am not sure.
Click to expand...
Click to collapse
Same problem occurs the system fails to download
don't know if you have already fixed the device or not but maybe flashing 4 files firmware can help you. I was able to flash all without any problem.
use samfirm with "binary nature" enabled.
adarshadhungel1 said:
don't know if you have already fixed the device or not but maybe flashing 4 files firmware can help you. I was able to flash all without any problem.
use samfirm with "binary nature" enabled.
Click to expand...
Click to collapse
I just tried this but still failed in aboot.mbn
john.reyes.jmr said:
I just tried this but still failed in aboot.mbn
Click to expand...
Click to collapse
Aboot.mbn is the bootloader. If Odin fails when flashing this file, you need to try a different USB cable, different USB port, the boot loader is not made for your phone, or you are trying to flash an older bootloader over a newer bootloader.
Samsung Bootloader does not allow to downgrade the ROM, Therefore I found a way to Downgrade Specially from Nougat to Marshmallow and Solution to SW REV. Check Fail.
Required:
1. Marshmallow or which you need Odin Firmware (Can be downloaded from Sammobile) for your Mobile.
2. 7zip installed.
3. WinRar installed (if 7Zip Shows error while Extracting the .tar file of firmware). I recommend this for extracting the tar file.
Steps:
1. Rename the Firmware from .tar.md5 to .tar so that WinRar can open it.
2. Extract the Firmware files except sboot.bin, cm.bin and modem.bin .
3. Now compress the extracted files to tar archive using 7Zip.
4. Done, Firmware is ready to flash through Odin.
cm.bin and sboot.bin causes to SW Rev check fail so If you face this error remove them from firmware.
If you like please hit Thanks button.
Hello, So basically we need to remove all .bin files? ok
I also need to downgrade my modem.bin because I'm facing Wi-Fi and Bluetooth issues (they don't turn on). So is it possible to flash those files separately after? Will it work?
x.shayan.x said:
Hello, So basically we need to remove all .bin files? ok
I also need to downgrade my modem.bin because I'm facing Wi-Fi and Bluetooth issues (they don't turn on). So is it possible to flash those files separately after? Will it work?
Click to expand...
Click to collapse
Yes you can flash
Afzal922 said:
Yes you can flash
Click to expand...
Click to collapse
I removed the files you mentioned and I flashed marshmallow on Nougat successfully but i have constantly getting error message ""Unfortunately, Touchwiz has stopped"" and "Unfortunately, The process. Android.process has stopped" and I can't boot in my mobile. Please help..!
alipezu said:
I removed the files you mentioned and I flashed marshmallow on Nougat successfully but i have constantly getting error message ""Unfortunately, Touchwiz has stopped"" and "Unfortunately, The process. Android.process has stopped" and I can't boot in my mobile. Please help..!
Click to expand...
Click to collapse
Try another firmware.
Afzal922 said:
Samsung Bootloader does not allow to downgrade the ROM, Therefore I found a way to Downgrade Specially from Nougat to Marshmallow and Solution to SW REV. Check Fail.
Required:
1. Marshmallow or which you need Odin Firmware (Can be downloaded from Sammobile) for your Mobile.
2. 7zip installed.
3. WinRar installed (if 7Zip Shows error while Extracting the .tar file of firmware). I recommend this for extracting the tar file.
Steps:
1. Rename the Firmware from .tar.md5 to .tar so that WinRar can open it.
2. Extract the Firmware files except sboot.bin, cm.bin and modem.bin .
3. Now compress the extracted files to tar archive using 7Zip.
4. Done, Firmware is ready to flash through Odin.
cm.bin and sboot.bin causes to SW Rev check fail so If you face this error remove them from firmware.
If you like please hit Thanks button.
Click to expand...
Click to collapse
mind telling us how to flash the .bin files to get back signals and wifi and other stuff?
if we not going to flash the CM and modem, i dont think the Wifi and the mobile signal is going to work....
Regards
i try this wat downgrade samsung 51 and its not work
Afzal922 said:
Samsung Bootloader does not allow to downgrade the ROM, Therefore I found a way to Downgrade Specially from Nougat to Marshmallow and Solution to SW REV. Check Fail.
Required:
1. Marshmallow or which you need Odin Firmware (Can be downloaded from Sammobile) for your Mobile.
2. 7zip installed.
3. WinRar installed (if 7Zip Shows error while Extracting the .tar file of firmware). I recommend this for extracting the tar file.
Steps:
1. Rename the Firmware from .tar.md5 to .tar so that WinRar can open it.
2. Extract the Firmware files except sboot.bin, cm.bin and modem.bin .
3. Now compress the extracted files to tar archive using 7Zip.
4. Done, Firmware is ready to flash through Odin.
cm.bin and sboot.bin causes to SW Rev check fail so If you face this error remove them from firmware.
If you like please hit Thanks button.
Click to expand...
Click to collapse
Hello, this is a well old post. Would this work with the Note 20 Ultra Snapdragon version?
N1NJATH3ORY said:
Hello, this is a well old post. Would this work with the Note 20 Ultra Snapdragon version?
Click to expand...
Click to collapse
Yes