Sprint LS980 in an odd state after trying to flash CyanogenMod 12.1
Ok... so I got two of these Sprint LG G2's. I was able to successfully flash the first one with a minimum amount of problems considering I was just learning how to do it.
This second one is a problem though. Here's what I did:
I tried to root but it could not due to the version of the Sprint firmware on the phone. I did the TOT stock flash to get it back to stock. That worked fine.
Then I was able to root it via ioroot. Once rooted, I installed FreeGee and tried to install TWRP, that didn't seem to work, so I installed CWM Recovery. I did option two on this thread to try to get the loki stuff installed using openrecovery-twrp-2.6.3.4-ls980. That "installed" and I was able to boot into it. I installed cm-12.1-20151125-NIGHTLY-ls980 (same one I used on the other phone). That would not install via CWM and gave an error about not being able to lokify (or something like that).
So I said, OK, I must have done something wrong, so I tried to redo stock flash again. That acts like everything works fine LGFlash does it's thing (using LS980ZVA_01.TOT), but the phone boots up and does not seem to finish the install process. The LG logo comes up and not the Sprint screen that I would expect. I can do this over and over again and the results are the same whether I let it sit for an hour or 10 minutes after flashing. So now, the phone boots, but I can't do anything with the touch screen, and will then go into a reboot loop (getting into the OS but rebooting shortly after). I CAN get into CWM where I can wipe data/factory reset and wipe cache partition. After I do that, the phone will boot and will let me interact with it, but after a short time (a few minutes I think), it will reboot again and be in the same state it was before I went into CWM. I tried to do a factory reset in settings. It would say that two reboots would occur, but then nothing happens.
I'm at a bit of a loss as to where to go from here. I don't think that it's an unrecoverable brick, but heck if I know how to fix it.
In between reboots, ADB does see the device in ADB Devices, but shows that it's offline, so I can push an APK to it.
Here are the options that I get in recovery mode:
Reboot System Now
Apply Update From External SD Card
Apply Update From Cache
Apply Update from ADB
Wipe data/factory reset
Wipe cache partition
Any assistance is greatly appreciated!
Ok.. well.. I downloaded and flashed ZVE and it seems to have greatly stabilized the phone. However, it seems that I have lost the ability to do download mode and recovery mode. I can still get into the device through ADB, but ioroot no longer is able to root the device, so I can't install any recovery. There is a system update available to install, but didn't want to do that unless I'm good an stuck in this mode.
I also don't seem to be able to enable the cellular service. I don't know if the update it wants to install would fix that or not.
Edit: I can still do ADB reboot recovery and get into recovery mode with these options:
Apply Update From External SD Card
Apply Update From Cache
Apply Update from ADB
Wipe data/factory reset
Wipe cache partition
Edit2: I was able to root with Stump. FreeGee won't run on ZVE, so not sure what to do from here. The phone does not work at all. None of the phone info is listed in About Phone. No IMEI or anything.
Edit3: I have been able to get TWRP installed and can boot into it. I have also verified that I can get into download mode now. I'm very concerned about my EFS info though. I did back it up, but not to the PC, so effectively I have no EFS backup and no way to recover the IMEI information. Not cool...
Related
I'm trying to install CM via TWRP.
First I had to unlock the bootloader, so I did, and since then I could not boot to my stock Android (although, correct me if I'm wrong, unlocking the bootloader should NOT delete the OS), it just sent me to recovery.
So I went along, flashed TWRP and got cm 10.2.1 for jfltexx. At first it didn't install well, because my data partition was not formatted correctly. So I formatted it, now TWRP sees it correctly and is able to mount it, enable MTP and everything. When I try to install now, everything seems fine and TWRP's log shows "Updating partition details..." and gives me the "Successful" message, offering to wipe cache/reboot system. (I did wipe cache and dalvik cache before, of course).
If I choose "Reboot System", it just boots back to recovery. The same happens if I power it off and boot normally, even if I pull out the battery and retry that way.
What can I do about it?
Jon-G said:
I'm trying to install CM via TWRP.
First I had to unlock the bootloader, so I did, and since then I could not boot to my stock Android (although, correct me if I'm wrong, unlocking the bootloader should NOT delete the OS), it just sent me to recovery.
So I went along, flashed TWRP and got cm 10.2.1 for jfltexx. At first it didn't install well, because my data partition was not formatted correctly. So I formatted it, now TWRP sees it correctly and is able to mount it, enable MTP and everything. When I try to install now, everything seems fine and TWRP's log shows "Updating partition details..." and gives me the "Successful" message, offering to wipe cache/reboot system. (I did wipe cache and dalvik cache before, of course).
If I choose "Reboot System", it just boots back to recovery. The same happens if I power it off and boot normally, even if I pull out the battery and retry that way.
What can I do about it?
Click to expand...
Click to collapse
First I'd try a newer version of CM. That's an old one. It might not work and play well with a newer version of TWRP. Plus the newer version is a little more polished.
Second, if you must use that CM version, redownload it. You wouldn't be the first person who got a corrupted install file that causes screwball issues like this.
Third, if all else fails use Odin to reset back to stock and start over. Something might have gotten all borked up when you first modified the device that isn't letting the install work. A full restore to stock should correct that.
Skipjacks said:
First I'd try a newer version of CM. That's an old one. It might not work and play well with a newer version of TWRP. Plus the newer version is a little more polished.
Second, if you must use that CM version, redownload it. You wouldn't be the first person who got a corrupted install file that causes screwball issues like this.
Third, if all else fails use Odin to reset back to stock and start over. Something might have gotten all borked up when you first modified the device that isn't letting the install work. A full restore to stock should correct that.
Click to expand...
Click to collapse
Thanks for the reply.
Regarding the versions of CM and TWRP, I deliberately picked these versions due to their high download count (A sign I can trust these builds, being not too buggy). I'll try a newer CM version and another TWRP version if that didn't help.
I will also verify the MD5 for the downloaded file this time.
If I restore to stock via Odin, wouldn't that override the recovery? I've looked on some tutorial on how it's done, and it seems like the stock recovery is flashed, then used to restore the stock. Is there any way to use Odin to flash other ROMs?
EDIT: Nope cm-11-20140210 also failed, and I did verify the MD5 now. My TWRP is the newest available for jgedlte in the download page (2.8.0.1).
I did manage getting into some sort of a boot loop (The initial "Reboot System" brought back the recovery, but after a full power off and a reboot, the screen remains black and the phone vibrates every 4 seconds or so.)
EDIT 2: I tried to flash the stock back, following this tutorial. I downloaded the Open European version, flashed the AP but it failed during the write of system.img.ext4, saying that the image is invalid. I tried again with the PIT file, but it failed too (secure check fail while repartitioning...).
Hi folks,
I recently rooted by N4. It was running Android 5.0.
I also have MultiROM installed, with CyanogenMod installed as a secondary ROM.
I didn't realise I couldn't apply the OTA updates to the stock Android system (my oversight), and I allowed the device to download and (attempt an) the recent 5.0.1 update from Google.
When the update attempted to reboot the device, I could see in the terminal data that popped up, that it failed.
After that device now gets stuck in the booting stage with the little coloured balls drifting around.
I continued to use my phone with the secondary ROM (Cyanogen) for some days until I had time to sort this out.
MY ATTEMPTED RECOVERY
I read that ordinarily on a rooted device one would manually apply the various image files from the full 5.0.1 package.
So, following instructions found here: http://forum.xda-developers.com/nexus-6/general/guide-flash-factory-images-nexus-6shamu-t2954008
Using method two (long method).
... In fastboot mode I flashed the system, boot, recovery, cache (after clearing cache), radio images from the 5.0.1 stock image.
At first I didn't flash the bootloader (as I wanted to maintain the multiboot loader I had installed) nor the user.img (I don't want to lose my user data). I read this should work. But it didn't.
When it came to booting into recovery mode to finish the process, an android icon with a ! warning on it would appear, and I could not do the recovery.
So, I have since flashed the bootloader also. That didn't change much, except that my dual-boot boot loader is now gone, and the device is still not recoverable.
Is there something I am not doing correctly? How can I recover this device so that it has 5.0.1, my existing user data, and my existing dual boot bootloader?
Cheers,...
May have solved it...
I'll post another update in a moment. Posting this just in case someone starts responding to my question in the interim.
After further fiddling around, I may have resolved this issue. I've managed to get it into recovery menu, rebooted from there, and device is now in "Android is updating" mode. Looking good.
Will post new message soon as to whether this was successful or not.
Issues continue
So, after the device booted a screen appeared for a fraction of a second, that appeared to be the screen for selecting system language (as per what happens when a device is first run after a clean install). But the screen almost instantly goes black except for the little network icon and battery icon and time in the top right of the screen.
If I use the power button to lock the screen and again to activate it, the screen very briefly flashed up the language selector, then goes blank again.
So... it seems something odd is happening after applying the 5.0.1 file.
Any suggestions?
Flash the 5.0.1 factory image with fastboot
Sent from my Nexus 5 using XDA Free mobile app
jd1639 said:
Flash the 5.0.1 factory image with fastboot
Sent from my Nexus 5 using XDA Free mobile app
Click to expand...
Click to collapse
Well, this is what I resorted to doing. And it worked. Phone started and was as new. Of course, I lost my user data which is a ****. I did pull the SDCARD content over ADB, but am not sure how I'd go about pushing it all back on, into right locations, etc.
BUT—and it's a BIG BUT—when I re-rooted it and applied SuperSu, it couldn't be put into recovery mode any more. It would keep running through the SuperSu install process each time I'd attempt to go into Recovery.
I ended up ignoring this, and installing Busybox (with Play) and SuperSu.apk (via Play). But the SuperSU apk would keep saying its files needed to be installed/updated.
I forget the exact mess that unfolded, but eventually (after installing MultiROM) I could boot the phone as it would ALWAYS go into (custom) recovery.
So I starter the whole process again, with another clean install of 5.0.1, and yet now it is stuck at the bootloader (the little swirling balls screen).
AndroidWelcome said:
Well, this is what I resorted to doing. And it worked. Phone started and was as new. Of course, I lost my user data which is a ****. I did pull the SDCARD content over ADB, but am not sure how I'd go about pushing it all back on, into right locations, etc.
BUT—and it's a BIG BUT—when I re-rooted it and applied SuperSu, it couldn't be put into recovery mode any more. It would keep running through the SuperSu install process each time I'd attempt to go into Recovery.
I ended up ignoring this, and installing Busybox (with Play) and SuperSu.apk (via Play). But the SuperSU apk would keep saying its files needed to be installed/updated.
I forget the exact mess that unfolded, but eventually (after installing MultiROM) I could boot the phone as it would ALWAYS go into (custom) recovery.
So I starter the whole process again, with another clean install of 5.0.1, and yet now it is stuck at the bootloader (the little swirling balls screen).
Click to expand...
Click to collapse
Try a full wipe from Factory Recovery, and see if it will fix the bootloop.
Bootloop no more...
ariesgodofwar said:
Try a full wipe from Factory Recovery, and see if it will fix the bootloop.
Click to expand...
Click to collapse
(wiping the sweat from his brow...)
After many tedious hours of messing around with this beast... there is life beyond the bootloop.
Back to a stock install.
So, now I am wondering why the SuperSu/Root process didn't work on my last round on this.
The SuperSu installer would kick in EVERY time I went into Recovery mode, and would then reboot the phone. This made it impossible to do things with ADP because I essentially couldn't get into recovery mode. I wanted to push through some of the stuff I pulled using ADP before I wiped the phone previously.
I installed MultiROM (which includes TWRP [is that what it's called] recovery system. BUT then go stuck in a Recovery loop.
Not wishing to repeat that fiasco... does anyone more knowledgeable than I (not a difficult status to achieve) have any suggestions to what might have caused those issues?
So, yesterday i tried to install Euphoria OS on my phone, but in all of a sudden, the /cache partition corrupted, i was dumb enough and deleted it via TWRP, making my phone fall into the QPST status.
After fixing it, i proceeded and reflashed KitKat, but the phone only shows 8GB instead of 16GB, so i tried to fix this by flashing TWRP, everything went well, until i upgraded to Lollipop again.
It always bootloops no matter what i do, i really need my phone with my 16GB of storage back, it isn't a Hardware failure since the QPST diagnosis didn't say anything about mobo failures.
I can mount all the partitions, i can wipe it all, i can boot into bootloader and recovery, i can do basically everything but booting the system.
Any light on this? it either happens after i flash TWRP or after i try to root it.
Im running Android 5.1.1 stock.
List of tutorials i have tried (In order): http://forum.xda-developers.com/nexus-4/general/wip-unbricking-nexus-4-using-qpst-t2208289
http://forum.xda-developers.com/nex...unbrick-n4-t2347060/post43164157#post43164157
http://forum.xda-developers.com/google-nexus-5/help/nexus-5-stuck-boot-loop-lollipop-t3098632
Don't you dare tell me to reflash the ROM again, this is the first thing i have done, i did this 20 times already and it never worked. It isn't a ROM problem. It is a partition problem somewhere.
Fixed, had to use LGNPST to reflash JB 4.4.2, then upgraded to a ZIP version of the Lollipop ROM, then flashed the stock one.
I'm having the same problem with my Nexus 4. I read also about LGNPST, but I remember something about flashing the Optimus G cache partition I believe, then manipulating one of the prop files afterwards in order to get your 16gigs back. The problem is that all of the files needed to do this flash are attached to a stupid downloader site and so its full of pop up windows and adware from what I've seen. I can't get mine to boot into system, or bootloader, or recovery, etc. The device will not finish looping for debugging to be enabled, and even trying to boot into download mode is not happening. I've tried all I know to do, especially considering fastboot and adb both utilizeusb debugging. I really am baffled. Any root kits I've tried also don't work so far. Help please.
So I would have asked this question directly in the DirtySanta thread, but apparently I don't have enough posts to actually do anything there yet.
So my device is now in a rather bizzare zombie state. I did manage to get my device fully rooted with TWRP installed. Followed the instructions on how to get everything working with no problems. I ended up wanting to try to flash some audio mods (V4A and such), however they did not install properly, so I went and did what anyone else would do - restored to a full backup I made of the device before I started mucking about.
The restore did complete successfully, and I still have a device that has a working recovery, and an OS with root permission...but I can't flash anything anymore from TWRP. TWRP is unable to mount the /system partition after the restore, and seems convinced that I have no OS installed, even though there is one and the phone boots into it just fine. The restore I'm on now is post-flashing the Konverged Kernel. Attempting to restore to an even earlier backup (one I made just before flashing Konverged) produces similar results - the restore succeeds and produces a bootable phone, but TWRP still can't flash anything.
Just to cover bases I also tried running "fastboot flash recovery twrp-3.0.2-1-us996.img" again in case TWRP got messed up (trying to get the "Swipe to allow system changes" prompt to reappear - it didn't), with no changes - TWRP still works fine, but cant mount and edit /system and still claims I have no OS installed when requesting a reboot.
Any advice on how to get things working again would be greatly appreciated! Thanks!
This may be an issue with TWRP. When I had my Galaxy S3 rooted back in the day I would have this issue, also with a Nexus tablet I rooted as well. It turns out I needed to flash a specific "fixed" version of TWRP to fix the mount/flash issue. That was a long time ago though, so this might not be the problem, but I thought I would at least tell you my experience.
Sent from my LG-LS997 using Tapatalk
biglightbt said:
So I would have asked this question directly in the DirtySanta thread, but apparently I don't have enough posts to actually do anything there yet.
So my device is now in a rather bizzare zombie state. I did manage to get my device fully rooted with TWRP installed. Followed the instructions on how to get everything working with no problems. I ended up wanting to try to flash some audio mods (V4A and such), however they did not install properly, so I went and did what anyone else would do - restored to a full backup I made of the device before I started mucking about.
The restore did complete successfully, and I still have a device that has a working recovery, and an OS with root permission...but I can't flash anything anymore from TWRP. TWRP is unable to mount the /system partition after the restore, and seems convinced that I have no OS installed, even though there is one and the phone boots into it just fine. The restore I'm on now is post-flashing the Konverged Kernel. Attempting to restore to an even earlier backup (one I made just before flashing Konverged) produces similar results - the restore succeeds and produces a bootable phone, but TWRP still can't flash anything.
Just to cover bases I also tried running "fastboot flash recovery twrp-3.0.2-1-us996.img" again in case TWRP got messed up (trying to get the "Swipe to allow system changes" prompt to reappear - it didn't), with no changes - TWRP still works fine, but cant mount and edit /system and still claims I have no OS installed when requesting a reboot.
Any advice on how to get things working again would be greatly appreciated! Thanks!
Click to expand...
Click to collapse
I beleive you have to do Dirty Santa over again....The steps that is.
biglightbt said:
So I would have asked this question directly in the DirtySanta thread, but apparently I don't have enough posts to actually do anything there yet.
So my device is now in a rather bizzare zombie state. I did manage to get my device fully rooted with TWRP installed. Followed the instructions on how to get everything working with no problems. I ended up wanting to try to flash some audio mods (V4A and such), however they did not install properly, so I went and did what anyone else would do - restored to a full backup I made of the device before I started mucking about.
The restore did complete successfully, and I still have a device that has a working recovery, and an OS with root permission...but I can't flash anything anymore from TWRP. TWRP is unable to mount the /system partition after the restore, and seems convinced that I have no OS installed, even though there is one and the phone boots into it just fine. The restore I'm on now is post-flashing the Konverged Kernel. Attempting to restore to an even earlier backup (one I made just before flashing Konverged) produces similar results - the restore succeeds and produces a bootable phone, but TWRP still can't flash anything.
Just to cover bases I also tried running "fastboot flash recovery twrp-3.0.2-1-us996.img" again in case TWRP got messed up (trying to get the "Swipe to allow system changes" prompt to reappear - it didn't), with no changes - TWRP still works fine, but cant mount and edit /system and still claims I have no OS installed when requesting a reboot.
Any advice on how to get things working again would be greatly appreciated! Thanks!
Click to expand...
Click to collapse
So your phone isn't booting beyond TWRP? I'm assuming that's what you are saying. I only want clarification because you mentioned how it won't flash anything.
Try this. Go to "mount" and make sure system is checked. Then power off the device. Then use the button combo to boot back into recovery. It's power + volume down, as soon you see the LG logo let go of the power button and then press it again and hold it (never let go of the volume down button though). If done correctly you'll get a white screen asking you if you want to factory reset. Choose yes for both questions. This will boot you back into recovery. Once in recovery again go back to mount and check system again. Now reboot system. This method got me out of being stuck in TWRP after I had tried every other method I could think of.
PS. Make sure you are on a fully stock version of the ROM that came on your phone. This may work for any backup you have but just incase use the most stock version backup you have.
imucarmen said:
So your phone isn't booting beyond TWRP? I'm assuming that's what you are saying. I only want clarification because you mentioned how it won't flash anything.
Try this. Go to "mount" and make sure system is checked. Then power off the device. Then use the button combo to boot back into recovery. It's power + volume down, as soon you see the LG logo let go of the power button and then press it again and hold it (never let go of the volume down button though). If done correctly you'll get a white screen asking you if you want to factory reset. Choose yes for both questions. This will boot you back into recovery. Once in recovery again go back to mount and check system again. Now reboot system. This method got me out of being stuck in TWRP after I had tried every other method I could think of.
PS. Make sure you are on a fully stock version of the ROM that came on your phone. This may work for any backup you have but just incase use the most stock version backup you have.
Click to expand...
Click to collapse
Sorry if I wasn't clear, its a bit confusing to me also. Normally TWRP saying you have No OS installed is pretty bad news, but it seems to be a bit confused itself, since there IS and OS installed, and the phone boots into it.
The phone basically works exactly as you'd expect after the DirtySanta exploit. It can boot into whatever backup I restore it back to, and works just fine, root included. I can also boot into TWRP just fine also..... Its just that within TWRP, if I try to flash anything at all (apps, zip files, kernels) it comes back with an error just after "Updating Partition Details". The specific error is "failed to mount /system (invalid argument)". If I had to guess I'd think that /system was somehow marked as Read Only after I did the restore. I haven't needed to use the button combos for anything since ADB and Fastboot commands all work just fine too.
If I go into the "Mount" section in TWRP "System" is unchecked, if I tap it to try to check it the phone vibrates as if it accepted the input, but the check never appears. If I select "Mount System as Read Only" I can mount it though. I followed the instructions in the DirtySanta thread to a T, and am using all the recommended software versions.
I also tried restoring back to the backup I made just before flashing Konverged Kernel, with similar results. The restore works, and the phone boots into Android, but if I try to pick up where I left off and flash Konverged again from within TWRP, it fails with the "failed to mount /system (invalid argument)" again.
biglightbt said:
Sorry if I wasn't clear, its a bit confusing to me also. Normally TWRP saying you have No OS installed is pretty bad news, but it seems to be a bit confused itself, since there IS and OS installed, and the phone boots into it.
The phone basically works exactly as you'd expect after the DirtySanta exploit. It can boot into whatever backup I restore it back to, and works just fine, root included. I can also boot into TWRP just fine also..... Its just that within TWRP, if I try to flash anything at all (apps, zip files, kernels) it comes back with an error just after "Updating Partition Details". The specific error is "failed to mount /system (invalid argument)". If I had to guess I'd think that /system was somehow marked as Read Only after I did the restore. I haven't needed to use the button combos for anything since ADB and Fastboot commands all work just fine too.
If I go into the "Mount" section in TWRP "System" is unchecked, if I tap it to try to check it the phone vibrates as if it accepted the input, but the check never appears. If I select "Mount System as Read Only" I can mount it though. I followed the instructions in the DirtySanta thread to a T, and am using all the recommended software versions.
I also tried restoring back to the backup I made just before flashing Konverged Kernel, with similar results. The restore works, and the phone boots into Android, but if I try to pick up where I left off and flash Konverged again from within TWRP, it fails with the "failed to mount /system (invalid argument)" again.
Click to expand...
Click to collapse
I would run the dirtysanta exploit again from the beginning. Your assumption about being stuck in read only seems correct. I'm guessing you might have chosen read only on accident one time when you booted into TWRP and now it's stuck there.
Or you could try using flashfire to flash the TWRP.img
I am having the same issue. I tried doing the DAC mod that enables high impedance as always on. Audio quit working along with the stock music app. Did a restore from after I flashed the konverged kernel. And now no r/w ability and twrp will not mount system unless I check mount as read only. I was able to reinstall supersu from the recovery. But still have the issues.
Only thing I can think of is waiting for a return to stock unrooted method to Come out and re-root.
biglightbt said:
So I would have asked this question directly in the DirtySanta thread, but apparently I don't have enough posts to actually do anything there yet.
So my device is now in a rather bizzare zombie state. I did manage to get my device fully rooted with TWRP installed. Followed the instructions on how to get everything working with no problems. I ended up wanting to try to flash some audio mods (V4A and such), however they did not install properly, so I went and did what anyone else would do - restored to a full backup I made of the device before I started mucking about.
The restore did complete successfully, and I still have a device that has a working recovery, and an OS with root permission...but I can't flash anything anymore from TWRP. TWRP is unable to mount the /system partition after the restore, and seems convinced that I have no OS installed, even though there is one and the phone boots into it just fine. The restore I'm on now is post-flashing the Konverged Kernel. Attempting to restore to an even earlier backup (one I made just before flashing Konverged) produces similar results - the restore succeeds and produces a bootable phone, but TWRP still can't flash anything.
Just to cover bases I also tried running "fastboot flash recovery twrp-3.0.2-1-us996.img" again in case TWRP got messed up (trying to get the "Swipe to allow system changes" prompt to reappear - it didn't), with no changes - TWRP still works fine, but cant mount and edit /system and still claims I have no OS installed when requesting a reboot.
Any advice on how to get things working again would be greatly appreciated! Thanks!
Click to expand...
Click to collapse
Hey I was having the same problem and I fixed it myself messing around with a few things I could think of.
Here it is pasted from another thread.
Dinked around with a few ideas and got my problem fixed! Heres what I did.
1. Made a backup of system in twrp just in case.
2. Formatted system in wipe > advanced > and only checked system.
Panicked because I thought I bricked my device, wouldnt boot farther than the lg logo,
(next steps might be unnecessary but I panicked and tried them lol)
3. still had fastboot access so I repeated step 3 in the root method.
4. Reflashed boot2.img
5. Rebooted to recovery with volume- power, release power while keeping volume- at lg for a second then repress and hold power. Yes twice to get to recovery.
6. Restored system backup. (was able to fully boot now but with lag)
7. Reflashed konverged kernel.
And everything is working perfect now and I have my r/w ability and can mount system in recovery without having to select mount as read only.
---------- Post added at 09:57 AM ---------- Previous post was at 09:10 AM ----------
You can probably just wipe your system like I said in the previous post then Just restore it. I panicked and did a bunch of extra stuff. I realized that when I did my initial backup of my system, or said that its size was about 126247251477482716MB. So I'm guessing when I did my restore (possibly what happened to yours) that it somehow messed up the system.
I was running xXx 4.5, and decided to "upgrade" to 5.0.
I did the usual, wiped data/system, then flashed.
I got stuck in a bootloop, and found I had to double back and wipe /data.
I did that, got stuck at the boot animation.
If I go back to recovery, all the data is jumbled, I assume encrypted? I flashed a different twrp for 8.0 compatibility, no change.
I can't push/sideload anything (roms, recovery zips sideload fine), it fails.
So I flashed the stock recovery in fastboot, rebooted there, and tried to sideload via adb the stock 8.0 flash files.
Now it works at it for a few minutes and just comes back as "Installation Failed".
Where do I go next? All i can get to is recovery, fastboot, bootloader.
I've already factory reset/wiped everything, so don't care if I lose anything anymore.
Help?
Thanks.
It appears I found a solution, just a few posts below my own! I hate it when that happens.
Anyways ,
https://forum.xda-developers.com/showpost.php?p=75364805&postcount=7
seems to have got the ball rolling, I was able to copy files to my phone while in twrp, which I couldn't do before, and currently have xXx installing. The first time it installed it didn't ask about encrypted/decrypted and didn't give me any warnings, this time it did.
xXx still won't boot after flashing, trying stock full flash file..
edit 2: Was able to flash full oneplus update file and boot. had to do a factory reset after rebooting as it was crashing a ton and wouldn't get through setup. It's been running fine since though. Now I'm a little skittish to try again, there are some root features I'd really like to still have.
I have a OnePlus 5 phone stuck in the Fastboot mode, been contacting them for days now but I still keep hearing the same excuses that the matter has been escalated to their tier 2 tech support team Nd would be contacted. Please is there a way to copy files off the phone in this state before it's flashed?