Database Users

Updated ON Officle lollipop 5.0.2 And Facing soft brick(How to Unbrick?)

Hello guys please help me, I am On latest official lollipop . I am trying to root my device and try to install twrp recovery flash, suddenly recovery got a error:crying:, Now I am on Lollipop My stock and twrp recovery is gone, i am not able to boot into recovery option, Just Yu logo come and mobile gets switch off. I think i got soft brick my device. but i Am able to go to fastboot mode?. I hear that cant flash cm11 after cm12 update so i cant go back to cm11, Just tell me friends what to do?
- if i have to flash again stock cm12 recovery? to get recovery option? If yes then please some one provide me cm 12 stock recovery
- if i have to flash cm12 how can i flash? via flashtool? but no firmware cm12 available right now
Help Guys

reply
reply Guys please:crying:

Have a look at this thread at YU - http://forums.yuplaygod.com/threads...6-0-for-yureka-arm64-flashable-lollipop.8630/
If you can enter fastboot mode, you can simply flash the TWRP recovery and then do root your phone. You can even try factory reset and see if you can boot again into your ROM. If can't, then you would need to flash whole CM12S ROM via fastboot mode. Here is the link for the CM12S ROM to be flashed in fastboot mode only -
http://builds.cyngn.com/cyanogen-os...cm-12.0-YNG1TAS0W0-tomato-signed-fastboot.zip
Warning : Do not even dare to think to go back to or use anything from CM11s. Hit thanks if it helped. Good luck!

been there, and recovered.
this is what I think you need to do to recover:
download
1) dr ive .google . com/file/d/0B0_IwOvcRE4gcnNHcF9wNDcxRGs/view
2) docs. google. com/file/d/0B0_IwOvcRE4gcUpnSmVjdDAzOE0/view
3) drive. google. com/file/d/0ByDCheN6iyw0WEpveWJoTnRiWnc/view
Steps to follow:
1) extract zip (1) and (2) in the same folder
2) power off your phone completely- if in doubt, pull out and reinstall battery.
3) place zip (3) in the root of your sd card of phone, and put the sd card back into the phone.
4) connect the phone in fastboot mode, and run "flash-all.bat"
(If it asks you to unlock your bootloader, do so by following the onscreen instructions.)
5) after process is complete, power on your phone after disconnecting.
6) let it boot up for a while, say 20 mins. this step may be skipped.
7) boot into recovery mode, and click on apply update.
8) navigate to the folder with zip (3) in it, and apply it.
9) if it gives an error, wipe cache and retry.
10) after process finishes, power on phone and let it welcome you to lollipop.
cheers!

[BPH6][24.08.16][SM-G935F/FD/W8] SuperMan-Rom V1.12 Aroma -> Flash FAIL

Hello,
http://forum.xda-developers.com/s7-edge/development/rom-s7-edge-rom-v1-1-t3356699
This ROM looks great !!! I managed strictly following the steps below to install the rom on my S7 Edge once. Later I wanted to reflash the ROM to change things in AROMA. Since it is impossible for me to go beyond the boot Samsung screen (every time I wait more than 30 minutes, it seems blocked and the phone becomes hot). Since I tried doing all the steps again thinking to reflash the CP and BL, TWRP, and disable encryption of /data partition etc but I still have the same problem.
During the installation of the ROM, I tried several setups, with or without root, with differents kernels etc, nothing works, the installation goes smoothly. It's just that the phone remains locked at startup ("Samsung Galaxy S7 edge, POWERED BY android").
I have Odin 3.10.7 and 3.12.3, TWRP 3.0.2-3hero2lte, BL_G935FXXU1BPH6 and CP_G935FXXUBPH1 and no-verity-opt-encrypt-2.1.
I also tried flashing stock rom and then Superman and fail again.
Could someone help me ?
Thank you.
(I just didn't do the step with CSC because it's seems to be optional)
1. Start your phone, go to settings, about device, software info and hit build.number around 10 times so developer options will show up
2. Open developer options and tick: OEM unlock
3. Shut your phone off
4. You now need a computer, download odin3.10.11
5. Download two files, first is bootloader and second modem: bootloader and modem
6. Boot your phone into download mode by pressing: home+volume down+ power on
7. Open the downloaded odin on your windows pc and click on BL tab and add the file that name begins with BL, same for CP tab
8. After this, reboot to download mode again
9. Install TWRP (latest one is needed to support new BL's) will be next step, for this, follow all steps provided in this forum: TWRP Thread (booting into download mode: press home+volume down+power on, booting into download mode press: home+volume up+power on)
10. when you got TWRP working: We need to disable encryption, for this you should boot into recovery mode (as described above)
11. Flash this on your phone
12. After flashing this, hit wipe, full wipe (this will clean all internal memory and your data will be lost!!)
13. you can test if encryption is still enabled, if TWRP shows error about not mounting /data your phone is still encrpyted
14. Now you can download the rom onto your PC and then transfer it via usb to your phone
15. It is rom installing time install the rom!
16. After successfully installing the rom hit reboot and you are good to go!
17. If you want you can use my csc selection to get your desired csc, if you want that you can grab it here: CSC Selection V1.6

i can't install twrp on galaxy core prime (sm-g361f)

i tried everything, but i can't install twrp. i tried to install via odin 3.12.3 but nothing. how can i resolve this issue? i tried also with a pre-rooted firmware.

hello,
fedetrevi1 said:
i tried everything, but i can't install twrp. i tried to install via odin 3.12.3 but nothing. how can i resolve this issue? i tried also with a pre-rooted firmware.
Click to expand...
Click to collapse
dude write some more info will you, i dunno whether
your device is locked
you have developer drivers on your laptop
what TWRP version you are trying to install
but anyways if the whole process is completed without any results consider starting odin as an administrator then flash TWRP

Hello sir
Follow my steps for successful TWRP/ROOT
1.)Download and install Samsung USB Drivers
2.)Download TWRP 3.0.2.0
3.)Download Odin
4.)Download SuperSU.zip file
For download links message me or add me on facebook facebook. com/fRoD.cs
After you complete this 4 steps shutdown your phone and enter into Download Mode
Volume Down + Power + Home
Select continue by Volume Up key
Now connect phone with usb cable into pc and run Odin as administrator
Click on AP box and select the twrp.tar file you download before
Go to Options tab and uncheck Auto Reboot, make sure that only F, Reset Time is checked and click start
After successfully installed TWRP , remove the battery, put it back and make sure that you go into recovery mode immediately!!! Volume Up + Power + Home
If you boot up the phone it will restore the original recovery. Thats why you need to go to recovery mode first.
First time you boot in recovery it will be shown a TWRP screen asking to allow modifications to system partition. Swipe to accept that.
Now select Install option and select SuperSU.zip file. By default it should be in Download folder, and swipe to start install
After installing click reboot and your SM-G361F will be rooted. You should have SuperSU app in the menu

Working Recovery
stevo4 said:
Hello sir
Follow my steps for successful TWRP/ROOT
1.)Download and install Samsung USB Drivers
2.)Download TWRP 3.0.2.0
3.)Download Odin
4.)Download SuperSU.zip file
For download links message me or add me on facebook facebook. com/fRoD.cs
After you complete this 4 steps shutdown your phone and enter into Download Mode
Volume Down + Power + Home
Select continue by Volume Up key
Now connect phone with usb cable into pc and run Odin as administrator
Click on AP box and select the twrp.tar file you download before
Go to Options tab and uncheck Auto Reboot, make sure that only F, Reset Time is checked and click start
After successfully installed TWRP , remove the battery, put it back and make sure that you go into recovery mode immediately!!! Volume Up + Power + Home
If you boot up the phone it will restore the original recovery. Thats why you need to go to recovery mode first.
First time you boot in recovery it will be shown a TWRP screen asking to allow modifications to system partition. Swipe to accept that.
Now select Install option and select SuperSU.zip file. By default it should be in Download folder, and swipe to start install
After installing click reboot and your SM-G361F will be rooted. You should have SuperSU app in the menu
Click to expand...
Click to collapse
https://forum.xda-developers.com/ga...sm-g361f-unofficial-twrp-2-8-7-3-0-2-t3425402

hi
I have a problem with my g361f. After few sec proces of flashing twrp failed.. Can you help ?

thocenski said:
hi
I have a problem with my g361f. After few sec proces of flashing twrp failed.. Can you help ?
Click to expand...
Click to collapse
Ah, opportunely, I have the exact same device.
Now, I have actually installed TWRP before so I can help.
Usually, if it stops the flashing process, it may be a case of the Custom binary being blocked by the FRP lock on the device. Have you OEM unlocked it?
On the device, when you boot it into download mode, does it say FRP LOCK: ON on the screen?
If not, skip this step.
If so, you need to do the following:
1) Reboot the device normally
2) Go into Settings, Developer Options (note: to enable it, go to About Device and spam the Build Number box until it says that you are a developer)
3) Find where it says 'OEM Unlock'
4) Confirm the change
Now, there is an extra step which I had to take if you have a Google account signed in on your device. You might not need to, but it's best just in case:
1) Go to Settings, Accounts and Google
2) Click the Google account on the device
3) Click 'Remove Account' and confirm
Note: You will need to sign in to use any of the GApps, but you cannot access the recovery whilst being signed in because of the FRP lock.
4) Reboot your device into download mode and try again.
This may not be the case, though.
Also, don't bother with adding that guy on Facebook. I have all the downloadable things you need here, but I advise you do follow his guide, except the Download folder section. He missed out that you need to download the SuperSU binary to your device. Downloads are here:
Here are the Samsung USB Drivers for Mobile Phones (NOTE: You may not need these at all since you can actually begin the flashing process without them, so don't bother):
http://developer.samsung.com/galaxy/others/android-usb-driver-for-windows
Here is the TWRP recovery (NOTE: Please download the 3.0.2.0 version, since it is more up-to-date and more likely to succeed:
https://forum.xda-developers.com/ga...sm-g361f-unofficial-twrp-2-8-7-3-0-2-t3425402
And here is ODIN (You already have it, but here it is anyway. Also, download the first one, not the second one, since the first one is newer):
https://odindownload.com/download/
Also, the SuperSU binary (Note: It's easier to open it in your Android browser and download the file from there. That avoids the need to transfer the file from the PC to the phone):
http://www.supersu.com/download
Now, it could, in fact, be a problem with the USB cable. It's highly unlikely, but mine is a bit tempermental, insisting that if I nudge it, it'll stop working.
Notify me how it goes, because this worked first time for me.

fedetrevi1 said:
i tried everything, but i can't install twrp. i tried to install via odin 3.12.3 but nothing. how can i resolve this issue? i tried also with a pre-rooted firmware.
Click to expand...
Click to collapse
Go to developer settings and check OEM Unlocking (if its already checked recheck it) and then reboot. Then close the phone and install TWRP.

Hi I've managed to install the correct twrp on my device but when I go into recovery I get the same message not seandroid enforcing. I've followed all the steps but I can't get it into recovery on twrp. Does anyone have a solution please?

Bootloop, No Twrp, No fastboot

Please read my problem:
1: I flashed using miflash oreo rom
2: Android 9 update comes to my mobile ,i did it
3. I flashed custom rom (derpfest pie version)
4: I wiped system, data, cache and flashed siberia os using twrp
5: Botloop on android one logo
6: Tried Power+Vol Down : No fastboot
7: Tried Power+Vol Up: No twrp. it show no comand screen
It just restarting continously after androidone logo. Meanwhile I getting VENDOR ERROR after mi flash.Before flashing sberia I was able to do fastboot and twrp. I even tried all three butoon press (VOl + - power). but same behaviour
Let me alive my device please
Thanks

Same happened here.plz help

Swaniya786 said:
Same happened here.plz help
Click to expand...
Click to collapse
I solved it
- exhaust mobile battery by doing bootloop without charging
- when battery is empty, connect usb cable with all drivers installed
- now try to bot in faastboot (power+vol Down)
i am sure after one or two attempt you will gee to fastboot
- now follow below guide:
c.mi.com/thread-2251485-1-0.html
in above URL i got error while restoring twrp backup.To resolve it first make backup of your corrupted rom device.Then using file explorer on PC remove all files.And replace all downloaded one.Delete all backedup files first.(Mind it)\\
Enjoy
If unable to get into fastboot, get battery zero and retry, Dont loose hope.Dont use any special method to zero battery.Simple let it restart

Root, flash recovery and custom ROMs. Only for LG G6 H872 (20g original firmware)

This is a much easier way to flash a new recovery and custom roms. Besides using a PC / USB cable for unlocking the bootloader, all the process can be done straight from your device.
IMPORTANT: This procedure is only valid for LG G6 H872. Other G6 variants will end up bricked. All partitions will be wiped, this means that all the files needed must be saved to your external SD. It’s been tested with 20g firmware.
Prerequisites:
LG G6 device with original Oreo 20g firmware and fully charged
External SD card
Download and install su98.apk, Root Checker and Flashify
Download this specific TWRP version and save it to your external SD
Download Magisk and save it to your external SD
(Optional) Download latest TWRP to flash A10+ custom roms and save it to your external SD
0. Backup everything
1. Unlock your bootloader, otherwise you will brick your device. You can follow this guide.
2. Disable Google Play Protect (from PlayStore) or you won't be able to go on with the next step
3. Install su98.apk, open it and tap INSTALL NOW (leave the checkbox blank)
4. Install Root Checker and open it to verify that your device is rooted
5. Install Flashify and open it to flash TWRP (recovery_h872_20180813-1.img)
6. Turn off the phone (at this point, if the phone boots to Android you will have to start over from step 3).
7. Reboot into recovery (press and hold Volume Down and Power buttons together for a few seconds. When the LG logo appears, release the Power button while keep pressing the Volume Down and then press the Power button once more. Once you see a white screen, use Volume keys to choose "Yes" and Power button to select the option, you will have to press “Yes” twice).
8. Once in TWRP (be patient, takes some time to load) a “decrypt data” legend will appear. Press cancel. Then swype to allow system modifications. After that, go to Wipe / Format data and confirm by typing yes.
You are now able to flash any Stock ZIP (not KDZ). If this is your choice, remember to flash Magisk after flashing the ROM. If you want to flash any other custom ROM, jump to the next step.
9. Still in TWRP, flash Magisk to keep your device rooted
10. Flash the latest TWRP. Go to reboot options and tap Recovery
11. Once in the new TWRP, wipe system, data, dalvik, cache
12. Flash Rom + Gapps + Magisk and reboot to system
VIDEOS
Unlock bootloader LG G6 - H872
Root LG G6 - H872 without PC
Special thanks to Man Stevo for sharing this!!

LG G6 H872 back to stock Oreo 20g
IMPORTANT: All partitions will be wiped, this means that you must backup everything otherwise you’ll lose everything stored in the phone.
Prerequisites:
LG G6 device fully charged
USB cable
LG Mobile driver installed
Patched LG UP installed in the right folder (otherwise your device will not be recognized)
LG G6 H872 latest Oreo firmware (20g)
0. Backup everything.
1. We are going to flash this using the patched LG UP. Place the files in C:\Program Files (x86)\LG Electronics\LGUP. You can't just unzip it anywhere and run it, it will not find the model file.
2. Boot to download mode (power off your Phone. Plug one end of the USB cable to PC and while holding the Volume Up button connect the other end of the cable to your device. Release the Volume button once the device boots into Download Mode. To exit the Download Mode, press and hold the Power button until the device reboots)
3. Open LG UP and wait until the device model is recognized. Then choose partition DL
4. Pick the H872 20g KDZ and click start / ok
5. You’ll now get a list of partitions to flash, check them all and click start / ok
6. You may get a warning about additional modified partitions. Ignore it, and click ok
7. When the process is finished, the device will reboot
If the progress bar reached 100% and the device got stuck in the pink bootanimation, follow these steps:
Unplug the device and turn it off by holding Volume Down + Power (keep holding them down until it turns off)
Once the device is off, press and hold Volume Down and Power buttons together for a few seconds. When the LG logo appears, release the Power button while keep pressing the Volume Down and then press the Power button once more. Once you see a white screen, use Volume keys to choose "Yes" and Power button to select the option, you will have to press “Yes” twice.
The phone will now restore factory defaults and reboot to system
IMPORTANT
In case camera crashes when opening or you get an IMS error, you'll have to flash H87211h_00_0406.kdz (same procedure as above from step 0 to 7, just changing step 4 where you need to pick H872 11h KDZ), reboot to system (until you finish the initial wizard) and then flash H87220g_00_1228.kdz (again, same procedure from step 0 to 7).

Reserved

Works like a charm. Thanks
FYI, Going back to full working stock need to return to Android 7 firmware 1st (H87211h_00_0406.kdz); otherwise, you will get camera and IMS error.
Questions:
Does SkyHawk Recovery support stock firmware as TWRP can't backup and restore stock properly.

e20140 said:
Works like a charm. Thanks
FYI, Going back to full working stock need to return to Android 7 firmware 1st (H87211h_00_0406.kdz); otherwise, you will get camera and IMS error.
Questions:
Does SkyHawk Recovery support stock firmware as TWRP can't backup and restore stock properly.
Click to expand...
Click to collapse
Worked here when getting back straight to stock 20g, but good to know for those with issues.
I didn't test any custom recovery to backup stock, so I don't know about that.
Thanks for reporting!

Has anyone else used this recently? I cannot get the phone to boot to recovery at step 7. I've tried:
1) press vol- and pwr until the LG logo appears, release power, and press it once more
2) same as 1) above, but pressing power button multiple times to get through the "your phone can't be checked for security stuff" warning
Both times, it just boots straight to Android.
EDIT: Using adb reboot recovery worked!

Yeah, it works @zolotiyeruki
Check the vídeo in the first post for more details with the whole procedure.

Anyone else get an antivirus warning for the su98.apk?
My AV indicates it has a trojan in it - Trojan:Script/Ulthar.A!ml

AmbientMix said:
Anyone else get an antivirus warning for the su98.apk?
My AV indicates it has a trojan in it - Trojan:Script/Ulthar.A!ml
Click to expand...
Click to collapse
To follow up on this, I believe it's flagged because it is the exploit to get root that is seeing.
So it seems it's getting recognized by the anti-virus correctly and it's the desired functionality of the .apk.
(Anyone feel free to chime in to correct this if it's inaccurate.)

AmbientMix said:
To follow up on this, I believe it's flagged because it is the exploit to get root that is seeing.
So it seems it's getting recognized by the anti-virus correctly and it's the desired functionality of the .apk.
(Anyone feel free to chime in to correct this if it's inaccurate.)
Click to expand...
Click to collapse
Exactly.

hello Magisk no longer provides a downloadable zip to flash with twrp. that and for some reason i cant seem to get twrp to stick after flashing ive followed the instructions as exactly except for not installing magisk via twrp. i tried to install magisk via the manager after flashing twrp the first time and wiping data after that i am givin the option to reboot to system which i tried first and was not able to boot back into twrp. after doing everything from step 1 to finish all over i tried staying to flash the latest twrp before returning to system but seeing as how i dont have any gapps or roms or a flashable zip for magisk i just rebooted to system after flashing and still could not return to twrp..... i need help how do i get twrp to stick around after reboot, and how am i supposed to install magisk properly without the flashable zip? i seem to need a copy of my current boot.img so i can patch it with magisk and flash it with fastboot, how do i do this?

jsjames7715 said:
hello Magisk no longer provides a downloadable zip to flash with twrp. that and for some reason i cant seem to get twrp to stick after flashing ive followed the instructions as exactly except for not installing magisk via twrp. i tried to install magisk via the manager after flashing twrp the first time and wiping data after that i am givin the option to reboot to system which i tried first and was not able to boot back into twrp. after doing everything from step 1 to finish all over i tried staying to flash the latest twrp before returning to system but seeing as how i dont have any gapps or roms or a flashable zip for magisk i just rebooted to system after flashing and still could not return to twrp..... i need help how do i get twrp to stick around after reboot, and how am i supposed to install magisk properly without the flashable zip? i seem to need a copy of my current boot.img so i can patch it with magisk and flash it with fastboot, how do i do this?
Click to expand...
Click to collapse
Download latest Magisk APK, rename it to ZIP and flash it through TWRP.