Related
Hi all, this is my first post on this forum but I've been reading for a while to educate myself.
I've got a Herm200 that I've been trying to troubleshoot but to no avail. I'm fairly certain that it has a hardware problem but I haven't been able to isolate anything.
Here's whats happening:
Occasionally the screen will come out of stand-by all white. This will also happen randomly if i touch the screen to perform a command. While the screen is operating, sometimes the buttons on the face will stop working, however the buttons across both sides will continue working just fine.
When the screen turns all white a soft, hard, or stand-by cycle will not always bring it back to life. The fact that the hard reset wont always fix the problem makes me think it's a hardware issue since the phone will boot-up with the the all-white screen.
This is incredibly frustrating especially since HTC wont accept any warranty claims in the USA on the Tytn.
At first I thought this might be a problem with the ribon connection between the screen and the base but i haven't been able to confirm or discount anything at this point. I have yet to find a way to consistently reproduce or rectify the problem so it's very hard to troubleshoot.
I pretty much have to take a second phone with me everywhere right now just incase i need to make a call. Please help! Has anyone ever encountered such a problem?
Thank you in advance!
SneezyRobot said:
Occasionally the screen will come out of stand-by all white. This will also happen randomly if i touch the screen to perform a command. While the screen is operating, sometimes the buttons on the face will stop working, however the buttons across both sides will continue working just fine.
Click to expand...
Click to collapse
Hi. This sounds very similar to a problem that I experienced with a HERMES100. I bought the phone off someone on Ebay recently - someone had obviously scrambled the radio on it. I re-flashed it, and it sprang to life. However, after a couple of days, I experienced a problem where occasionally the LCD would stop refreshing, all the pixels faded away leaving only a white screen. Under these circumstances, some of the buttons on the phone stopped working. Turning phone on/off sometimes cured the problem, or it would require the occasional hard reset. This would happen once or twice a day and I suspect thats why someone tried to re-flash the phone.
In the end, out of curiosity I took the entire phone apart, put it all back together again and now there are no more problems!! Totally fixed!
My suspicion is that it was one of the ribbon cable push connectors on the mainboard - possibly not seated properly, or a bit of dirt contaminating the connection. Obviously when I took the phone apart I must have re-seated it.
If you are planning to take your phone apart, please exercise considerable care because some of the parts are very small and easily damaged. I would recommend buying a proper kit to take it apart. I bought mine for about £5 off ebay. Particularly useful are the plastic spoon "wedges" used to gently prise open the case after removing the screens. Don't use a screwdriver - you will scratch the case.
Good luck.
wow... that sounds like exactly what's going on here, I actually even tried to disassemble it lastnight but didnt have the right driver set. thank you for the advice!
I'll look for one of those sets but what would you search for if i needed to find it?
Thanks again, I just got a set off of Ebay. Hopefully it'll be here next week
With any luck it'll be a connection issue.
I have had the exact same problem. Because I got the Tytn through work I made our IT department handle the issue and I am currently waiting for a replacement and to find out what happened.
Yep, it looks like the problems the OP is having are very similar to the problems we've been having over in this thread:
http://forum.xda-developers.com/showthread.php?t=291027
I'm beginning to think it's a hardware problem as well but not entirely sure.
People in the above thread mentioned that using the scroll wheel a while then moving back to use the D pad fixed the problem (very briefly in my case.) Once I use the center D pad button again it locks the hardware buttons under the screen until I make my device sleep and resume.
Somtimes rather than making all the front hardware buttons unresponsive the issue is that once I use the Down Dpad button I can't use the up button. Pressing up will make it go down, as will pressing down (at least that's working ).
Regarding the white screen - this sometimes also occurs. I can force it to white screen by putting a little pressure on the silver panel surrounding the top, right and bottom of the screen (I have an imate jasjam). Randomly when there's no pressure on the rim and I wake it out of standby, it has a white screen that can only be fixed by turning the screen off and on again.
Finally, the LED indicator seems screwy. Sometimes it never flashes. Other times it flashes sporadically (uneven intervals - we're talking maybe a minute between one flash then seconds before another). When I charge it sometimes the LED doesn't come on but nevertheless it charges. Sometimes if the LED is on it never turns green to indicate a full charge. Yet other times it comes on orange, turns green, then never switches off!
Is it possible that
a) The hardware button problems.
b) The white screen problem.
c) The LED problem.
are all related to some kind of connection going loose? Why would the hardware button problem be temporarily fixable with use of the scroll wheel if this were the case?
The other thread has fallen silent. I'm hoping that some of the gurus in here can offer some input here, even if they don't know the answer but can formulate an opinion. I know very little about these devices.
Thanks in advance guys!
PS - don't really know if I should start another thread, I've posted here as it seems like very much the same issue.
Anybody any idea? advice?
I had a similar problem with my HERM100. I didn't mess around with it too much, I just had Cingular replace it out of warranty exchange (thank god those original ROMs are on the wiki ). I did notice however that after doing a master reset, the screen would function again although I haven't messed around with it too much. I got so frustrated with removing the battery for 5 minutes and STILL powering on with a white screen that I just threw it in my back seat until the new one arrived.
I don't have these screen issues. I only have hardware button problems. It's so damn frustrating! I already own a replacement.
I just received a call from my girlfriend. I wasn't able to answer the phone with the buttons, only with a screentap. I also wasn't able to close the call with the hardware button. Since the side buttons work, I went to settings -> phone, closed it, and there we go. The hardware buttons worked again.
Why the heck is this? I truly hope for some wizz out there with some advice, since HTC would only tell me to send it back after replacing it with a new TyTN with same issues.
Regards,
DM.
Anyone anyone?
HELP!!!!
barncourt said:
Hi. This sounds very similar to a problem that I experienced with a HERMES100. I bought the phone off someone on Ebay recently - someone had obviously scrambled the radio on it. I re-flashed it, and it sprang to life. However, after a couple of days, I experienced a problem where occasionally the LCD would stop refreshing, all the pixels faded away leaving only a white screen. Under these circumstances, some of the buttons on the phone stopped working. Turning phone on/off sometimes cured the problem, or it would require the occasional hard reset. This would happen once or twice a day and I suspect thats why someone tried to re-flash the phone.
In the end, out of curiosity I took the entire phone apart, put it all back together again and now there are no more problems!! Totally fixed!
My suspicion is that it was one of the ribbon cable push connectors on the mainboard - possibly not seated properly, or a bit of dirt contaminating the connection. Obviously when I took the phone apart I must have re-seated it.
If you are planning to take your phone apart, please exercise considerable care because some of the parts are very small and easily damaged. I would recommend buying a proper kit to take it apart. I bought mine for about £5 off ebay. Particularly useful are the plastic spoon "wedges" used to gently prise open the case after removing the screens. Don't use a screwdriver - you will scratch the case.
Good luck.
Click to expand...
Click to collapse
This is my first post as I've so far managed to cure all my issues from just reading the forum. However, I am now having a similar problem with the white screen.
I have a cingular 8525. It fell and the following day the call and end buttons remained lit and wouldn't turn off and they also wouldn't work.
I soft reset, nothing, I then removed the battery and when I turned it back on, there was a white screen and the buttons below still don't work.
I have read the other posts on this issue, but I need help on exactly what kit to buy to reconnect the screen cable and instructions on how to do it as I've never taken apart a phone before, although I have dabbled with other electronic devices.
Your help would be much appreciated, as I am in Jamaica and there are no technicians here who I trust to help.
Thanks in advance.
Below are links to 2 kits I'm thinking of getting. Is either one better than the other?
http://www.pdasmart.com/pdaphonehtcmini.htm?gclid=CJrHntO-hosCFQx1VAodaQf6KQ
http://cgi.ebay.com/SCREWDRIVERS-TO...01677255QQcategoryZ108648QQrdZ1QQcmdZViewItem
CINGULAR IN JA said:
This is my first post as I've so far managed to cure all my issues from just reading the forum. However, I am now having a similar problem with the white screen.
I have a cingular 8525. It fell and the following day the call and end buttons remained lit and wouldn't turn off and they also wouldn't work.
I soft reset, nothing, I then removed the battery and when I turned it back on, there was a white screen and the buttons below still don't work.
I have read the other posts on this issue, but I need help on exactly what kit to buy to reconnect the screen cable and instructions on how to do it as I've never taken apart a phone before, although I have dabbled with other electronic devices.
Your help would be much appreciated, as I am in Jamaica and there are no technicians here who I trust to help.
Thanks in advance.
Below are links to 2 kits I'm thinking of getting. Is either one better than the other?
http://www.pdasmart.com/pdaphonehtcmini.htm?gclid=CJrHntO-hosCFQx1VAodaQf6KQ
http://cgi.ebay.com/SCREWDRIVERS-TO...01677255QQcategoryZ108648QQrdZ1QQcmdZViewItem
Click to expand...
Click to collapse
Both kits look ok. PDA one tells you a little more but the basics appear to be in both.
I'm curious though you soft reset and took the battery out, but have you done a HARD reset? I would always try this first before dismantling.
Mike
In my case, they also are always lit up when the screen is also active.
And no matter what ROM version, they occasionally stop responding. Side buttons keep working.
mikechannon said:
Both kits look ok. PDA one tells you a little more but the basics appear to be in both.
I'm curious though you soft reset and took the battery out, but have you done a HARD reset? I would always try this first before dismantling.
Mike
Click to expand...
Click to collapse
Thanks for the response.
I couldn't do a hard reset because the buttons weren't working.
I have made some progress with the phone now. Found a tech guy who looked at it for me. The white screen is gone, but the buttons still stop working from time to time.
All the connections seem ok.
Is there anything else that could cause the buttons to malfunction?
CINGULAR IN JA said:
Thanks for the response.
I couldn't do a hard reset because the buttons weren't working.
I have made some progress with the phone now. Found a tech guy who looked at it for me. The white screen is gone, but the buttons still stop working from time to time.
All the connections seem ok.
Is there anything else that could cause the buttons to malfunction?
Click to expand...
Click to collapse
Nothing obvious.
Have you got applications installed that you have loaded - could be one thats playing up.
Have you now been able to do a hard reset?
If taking device apart and reassembling improved things it does suggest hardware though and might be worth double checking all those multi-connector blocks for good connections - i.e. take them out and in a few times to ensure any oxidation on contacts is removed.
Mike
mikechannon said:
Nothing obvious.
Have you got applications installed that you have loaded - could be one thats playing up.
Have you now been able to do a hard reset?
If taking device apart and reassembling improved things it does suggest hardware though and might be worth double checking all those multi-connector blocks for good connections - i.e. take them out and in a few times to ensure any oxidation on contacts is removed.
Mike
Click to expand...
Click to collapse
Thanks Mike.
I will give that a shot.
I haven't installed any new applications recently, so I don't think it is a software issue.
Thanks again.
CINGULAR IN JA said:
Thanks Mike.
I will give that a shot.
I haven't installed any new applications recently, so I don't think it is a software issue.
Thanks again.
Click to expand...
Click to collapse
If it wouldn't be a software issue, why is it, in my case, instantly resolved when going to settings -> phone with the side buttons?
i had this problem i took it to a guy who fixed the problem he said it was a very small tear in the flex cable which causes this white screen every now ant then and the buton problem , sorry to say its the cable problem and u need a very capable person to fix it or replace it with a new one . its very common problem baised on the guy who fixed it .
dmxl said:
I don't have these screen issues. I only have hardware button problems. It's so damn frustrating! I already own a replacement.
I just received a call from my girlfriend. I wasn't able to answer the phone with the buttons, only with a screentap. I also wasn't able to close the call with the hardware button. Since the side buttons work, I went to settings -> phone, closed it, and there we go. The hardware buttons worked again.
Why the heck is this? I truly hope for some wizz out there with some advice, since HTC would only tell me to send it back after replacing it with a new TyTN with same issues.
Regards,
DM.
Click to expand...
Click to collapse
Exactly what is happening to me, no white screen issues, just screen taps and answering calls, I also have another problem where the PDA will not allow me to open anything, be it the start menu or contacts, it will open and quickly close again. I have had mine swapped through Telstra in Sydney, it worked fine for a while and then the same crap again. These problems started before I even touched the OS, so it must be a build problem. Maybe we should write a joint letter to HTC letting them know that there is a serious problem with their machine.
I have had the same problem, got my Tytn through work so we sent it back to the company that supplied it to us. Got it back yesterday and they had replaced the "switchboard". Not sure what it is but there was the problem. Had white screen and buttons not working.
Hi all,
I need help,suggestions,anything with an issue I've had for a while. Since the time I started loading WM6 the screen has been randomly fading to white. I have LSVW latest rom 22/4 SE and 1.40.10 radio and 1.40oli although it doesn't matter what rom you load. I tried going back to WM5 and its better but now still fades to white as well.
on advise from oli and legolas I purchased a new battery but still have the same issue.
I have dropped my phone once which resulted in a crack to the right of the DEL/CR keys so could it be a HW issue and if you think so is it one I could open up the phone and fix?
Any and all help appreciated
IN FACT IF SOMEONE CAN RESOLVE THE ISSUE I WILL DONATE SOME CASH TO THEM!
test
Im updating to
LVSW 4-23 Full, Radio 1.40.30.00, SPL 2.10.Oli, IPL 1.04
seeing if any difference comes out.
This is not the first time this issue has been reported:
http://forum.xda-developers.com/archive/index.php/t-301003.html
The conclusion is that it's hardware related. It may be as simple as one of the internal ribbon connectors having a less than firm connection. It may be brought on my anything from physical movement or pressure to internal pressure if the device gats warm. However, it is possible that there is a failing component. IMHO, a case of take it for replacement/repair or first check connectors if your brave and not worried about a warranty.
Mike
mikechannon said:
This is not the first time this issue has been reported:
http://forum.xda-developers.com/archive/index.php/t-301003.html
The conclusion is that it's hardware related. It may be as simple as one of the internal ribbon connectors having a less than firm connection. It may be brought on my anything from physical movement or pressure to internal pressure if the device gats warm. However, it is possible that there is a failing component. IMHO, a case of take it for replacement/repair or first check connectors if your brave and not worried about a warranty.
Mike
Click to expand...
Click to collapse
HHmmm interesting thread .. the only issue i have out of that is the fade to white one.
Maybe Hardware .. i got the phone off ebay and now it has a crack in it .. so i dare say it isnt under warranty any more. (even though its a max of 6 months old).
It may also be software. I experienced the WSOD on my JASJAM when playing with the GPS-related DLL's. Once this problem appeared when switching on the camera. The screen would turn white and soft reset would not fix this, only power off/on would sort it out. Seems that the drivers do not reset (some of) the hardware to a known state on boot.
Had EXACTLY the same problem. Hoped it would be a software problem. Hard-reset a few times to no avail. Upgraded to a couple of the WM6 ROMs. No change. I did notice that when it was cool it tended not to happen, but after being on the phone a couple minutes or using the PDA for a while, it would do it AGAIN.
One weird thing I noticed was that if I did a Soft-reset and held down the Left Soft-key, I could "force" it to fade to white on start-up! VERY WEIRD.
I finally bit the bullet, and sent it back to Telstra to get it sorted. Didn't want to void warranty myself.
It has been just over 2 weeks since I sent it off, and They have sent this reply...
-------
-------
Hi
This phone is currently waiting on a part which was ordered yesterday. Some parts have already been issued but needs further repair.
Regards
Nadine
--------------------------------------------------------------------------------
From: LJ Boyd [mailto:[email protected]]
Sent: Friday, 20 April 2007 2:18 PM
To: ! TMS Customer Service
Subject: RE: Imate JASJAM Problem
Hello, I am emailing about an I-Mate JASJAM phone I sent for repairs early last week (tel # xxx ).
Can you please update me as to status of this repair, as the Telstra shop did not provide me with a second phone while I await return/repair/replacement of the phone.
Thanks,
-------
-------
So, I guess it IS a hardware problem. But then again, that kind of reply, sounds a bit "dodgy" as it doesn't seem to "technical" does it?
Hope this helps.
jyetara said:
So, I guess it IS a hardware problem. But then again, that kind of reply, sounds a bit "dodgy" as it doesn't seem to "technical" does it?
Hope this helps.
Click to expand...
Click to collapse
Their reply was not very technical - does not surprise me however. The people who repair these devices are usually faced with some component/connection/screen or a m/board that needs replaced. They often fail to take account of something as basic as the case pressing on the screen or other components - particularly when device is warm. So they replace the component they think is faulty and then discover the problem is still there. With this issue in particular I think that there are no faulty components just the case is a fraction of a millimetre too tight for the internal components and hence swapping out parts can have no effect. With this fault I advise people to go for a replacement not a repair if possible.
NB: This issue should not be confused with white screen that may appear after installing particular software or when an application crashes, or when the flashing of a new ROM goes wrong! The hardware issue arises most commonly when the device gets warm or put another way goes white after maybe 10 minutes of use and will continue to go white even after hard reset.
Mike
I have this same problem! =(
My phone screen recently (4-5 days ago) started to go white. I never saw this happen with my own eyes but when i picked up my phone and its sleeping i push the power button to get to an all white screen. I can hear noises when i touch the screen but no image other than white. I can solve this by removing the battery and putting it back in, then my scren works fine....its not verry often just like 1-3 times a day.
I want to try a hard reset but have a question first: My phone is unlocked by the ebay guy i got it from, will a hard reset lock my phone back to Cingular?
Next i want to try upgrading my ROM and Radio and anything else...im looking in the wiki for instructions on how to do this. Any help? What else shouls i upgrade?
Ive only had my Hermes for around 2 months so im new to much of this.
THanks!
I recently purchased a Used Imate Jasjam (Ex Telstra Australia) with this issue.
I pulled the unit apart, and reseated and pressed the Power and LCD Display Data Cables... attempting to ensure they were firmly fastened.
I then upgraded to LVSW's Latest WM6 Release.
I have had the Phone go to White once in that timeframe since. I brought it back by pressing the power button of, then one again.
I don't feel that it's really a "100%" Faulty Part... Because it works fine othertimes. It almost seems as if connections or a Data Cable has an Issue.
I'm intending tonight and using the Phone over the weekend to see if the issue continues to occur.
BAD NEWS!!
Well, got my phone back after a bit over 3 weeks I think? I kept ringing the repair center and emailing. Finally they said it was ready, and was sent back to the shop I bought it from. Rang the shop "no it's not here yet, we will ring you"... now the repair centre to the shop is a 20 min drive... on the 3rd, I rang again at 1pm and "no it's not here yet, we will ring you when it arrives." At this point I was really getting p*ed off. So I went to the shop, and demanded, and guess what was AT the Shop?!?!?!
Anyway, after 1 friggin day, I have lost the Red & Green phone buttons! As of tonight the whole bottom section no longer work, and the screen has gone white again.
The repair report listed 3 things replaced...one was a "bezel" another was a "poly" something. I will get the report a list the replaced bits if anyone likes, but their descriptions are kind of strange if ya ask me.
Anyway, I have to send the phone back for repairs again, which could take another 3 weeks +, which I think is completely PATHETIC OF TELSTRA, especially for the fact they dont give the same phone or even similar to "loan" while I wait for my defective $1300 phone to get "repaired"... (more like 'fiddled with' & "yeah, she'll be right mate"...
GRRRRR!!!!
My girlfriends phone was having the same problem. Try popping out your SD card and putting the phone into/out of sleep and see if that brings back a visible screen. Thats how we determined her situation was a hardware problem and not a problem with the rom.
jyetara said:
Well, got my phone back after a bit over 3 weeks I think? I kept ringing the repair center and emailing. Finally they said it was ready, and was sent back to the shop I bought it from. Rang the shop "no it's not here yet, we will ring you"... now the repair centre to the shop is a 20 min drive... on the 3rd, I rang again at 1pm and "no it's not here yet, we will ring you when it arrives." At this point I was really getting p*ed off. So I went to the shop, and demanded, and guess what was AT the Shop?!?!?!
Anyway, after 1 friggin day, I have lost the Red & Green phone buttons! As of tonight the whole bottom section no longer work, and the screen has gone white again.
The repair report listed 3 things replaced...one was a "bezel" another was a "poly" something. I will get the report a list the replaced bits if anyone likes, but their descriptions are kind of strange if ya ask me.
Anyway, I have to send the phone back for repairs again, which could take another 3 weeks +, which I think is completely PATHETIC OF TELSTRA, especially for the fact they dont give the same phone or even similar to "loan" while I wait for my defective $1300 phone to get "repaired"... (more like 'fiddled with' & "yeah, she'll be right mate"...
GRRRRR!!!!
Click to expand...
Click to collapse
Yes, sadly this is kind of predictable as I said in an earlier post in this thread:
http://forum.xda-developers.com/showpost.php?p=1233420&postcount=7
This is why, as I said, get a replacement not a repair if possible. My view is that the individual components are fine but connectors come loose or the heat generated causes pressure to be put on the screen etc So it's a problem with some cases and how the innards in some cases get squeezed. So off course changing the top poly board, connectors, bezel gasket, may by pot luck make a difference but is just as likely to make no difference at all.
Mike
Status Report:
After having my phone playing Video's Through the Night (My Way of a "Stress Test" to Generate Heat) I woke up the find the screen to be "almost completely" White.
Usually its gone completely, however in this instance I was able to see the icons through the whitewash.
I put the phone into sleep and back out and the Display is fine again.
Being that these phones are much easier to pull apart and put back together than my old JasJar I might to do some further experimentation.
I think the issue will have something to do with either one of the following
- Heat
- Pressure on the LCD from Parts Around it
- Faulty Ribbon or Power Leads to the LCD
My suggestions
- In the Case of Heat... I'll run the Same Test, with the Phone Directly in front of a small airconditioning unit I have.
- In the Case of Pressure, I'm going to look and see if I can place some extra Insulation Tape or Similar on the Phone to relieve this
- I wish I could find somewhere to buy the Replacement Ribbon Cables but I don't know where I can get them in Australia... any ideas?
VolarisPtyLtd said:
Status Report:
After having my phone playing Video's Through the Night (My Way of a "Stress Test" to Generate Heat) I woke up the find the screen to be "almost completely" White.
Usually its gone completely, however in this instance I was able to see the icons through the whitewash.
I put the phone into sleep and back out and the Display is fine again.
Being that these phones are much easier to pull apart and put back together than my old JasJar I might to do some further experimentation.
I think the issue will have something to do with either one of the following
- Heat
- Pressure on the LCD from Parts Around it
- Faulty Ribbon or Power Leads to the LCD
My suggestions
- In the Case of Heat... I'll run the Same Test, with the Phone Directly in front of a small airconditioning unit I have.
- In the Case of Pressure, I'm going to look and see if I can place some extra Insulation Tape or Similar on the Phone to relieve this
- I wish I could find somewhere to buy the Replacement Ribbon Cables but I don't know where I can get them in Australia... any ideas?
Click to expand...
Click to collapse
We wait to see. Mind you one guy on these boards found he could get half an hour from his device if he put it in the freezer for a while - so I'm not sure that air-con will be strong enough!!!
Mike
Well Results.....
After pulling apart the unit and reconnected, I think I found my cause to simply be excess pressure.
I've removed the "Black Plastic" Micro SD Card from its Blanking Plate.
Since I've done this... not one White Screen Whatsoever.
I don't use an SD Card, so the issue is resolved for me, however it is very interesting.
Could be Pressure or Heat (Small Hole Might Increase Airflow/Allow for Greater Dissapation or something)
Hi folks,
i've also small experience with this "white screen" issue and just wanted to inform you about it.
I got the device from my former boss who did already complain about this "white screen" issue on his O² XDA trion with original ROM. (honestly i did not really believe him due to my experience with couple of other devices so after i got the device i was just wondering - ok back to the facts).
I installed on Friday the Windows Mobile VI Pro - BLACK 2.5 Release and until today it was running (as far as i remember expect one time) nearly perfect w/o white screens. About 45min ago, i flashed the device with BLACK 3.0 Release and got until now about 5-10 times a white screen.
I assume this is not a hardware ONLY issue but indeed very strange.
I'll go back to 2.5 and will look forward if i get again the white screen or it'll be ok.
Cheers so far
FaCeOff said:
Hi folks,
i've also small experience with this "white screen" issue and just wanted to inform you about it.
I got the device from my former boss who did already complain about this "white screen" issue on his O² XDA trion with original ROM. (honestly i did not really believe him due to my experience with couple of other devices so after i got the device i was just wondering - ok back to the facts).
I installed on Friday the Windows Mobile VI Pro - BLACK 2.5 Release and until today it was running (as far as i remember expect one time) nearly perfect w/o white screens. About 45min ago, i flashed the device with BLACK 3.0 Release and got until now about 5-10 times a white screen.
I assume this is not a hardware ONLY issue but indeed very strange.
I'll go back to 2.5 and will look forward if i get again the white screen or it'll be ok.
Cheers so far
Click to expand...
Click to collapse
You are right to ask the question "is it hardware or software".
1
We know a white screens can arise if folk duff up flashing a new ROM.
2
We know there is a hardware caused white screen that comes and goes often when device gets warm.
3
But there maybe white screens caused by some kinds of crashing software or a buggy ROM etc
Crucially in terms of finding a cure will be distiguishing between these.
2 for most people is easy - take it back and get a replacement.
1 is a matter for the ROM upgrading and fixing boards
3 is a case of trying different ROMs testing 3 party software by selective installation until the problem starts or stops.
In your case I am worried that this is a number 2 device as it did sometimes get the problem before you flashed the ROM and now it's worse. It may only be worse because this particular ROM is generating more heat and consequently more white screens. (see explanations elsewhere).
I suppose if it's an occasional problem you might live with it but otherwise it's replacement at best and repair as a rather dodgy alternative.
Mike
Hey Mike,
well, before flashing the device with a custom ROM, in my opinion it was really difficult to use it.
By flashing it with V 2.5, it was very good usable and with V 3.0 it returned to become more unusable. Nevertheless, i upgraded 10min ago with HARD-SPL-V7 and it's running fine now (i've been wating with downgrading to V 2.5. If it returns to become unstable, i will downgrade to V 2.5 again.
I'll keep you informed.
yes for this particular "white screen" issue it will be useful to hear how things go - thanks
Mike
White screen - in my case definitely a hardware issue
Hi folks,
i was testing and playing around with my Hermes and today i found the problem (very funny because now i can't reproduce it anymore but just read ahead).
Today i was playing around and after pressing by accident on the case of the Hermes, the screen appeared disappeared and changed into white.
Please download the video i recorded from the attached link - you'll see that it was able to reproduce it by tapping on the case:
http://asuka.descipe.de/dphome/test/HTC_Hermes_White_Screen_issue.mp4
Please use VLC or MPC (additional codecs required) to watch the movie.
Honestly i'm not sure if this can be reproduced by anyone but this makes the whole situation much more clear.
Any feedback is welcome.
Cheers
Ok so I have the fabled white screen issue on an 8525. When it first occurred I searched and read all the write ups, decided I had the ribbon cable issue. Took it apart and simply unplugged and replugged the ribbon cable with great results, no more white screen.
I repeated once when it came back after being bumped around, again with positive results...but this last(3rd)time instead of it working I now get white screen 95% of the time. I re-notched the sliders the first time, and last time.
During the 5% it works I noticed the charge light would correspond to it going white.This never happened before...
Example:
When OFF - Connect charger, Red light for 1 second, then nothing=White screen from power on
When OFF - Connect charger, Red light for 1 second, then orange charge indicator = normal startup
When ON and Working - Connect charger, no light, no charge - reboots to white screen
When ON and Working - Connect charger, orange charge indicator, reboots normally.
There is no heat or noticeable pressure on any parts, everything seems to fit normally.
It does boot normally with screen white.
Any ideas? I really don't want to give up on this thing, is there any hope? or just ebay it for parts?
Thanks
-Nick
same problems here, if someone could just tell me what parts to order, cause I have no warranty (ordered over ebay). I tried both the instruction that has chinese fonts on the page , and other from R&R, no luck, white screen all the way..
I had the WSOD and took it apart and reassembled a few time. The 3rd or 4th time the screem came back, but now it is shifter to the right around 1/4" or so. I mean there is just white along the left edge, then the normal screen/color starts and is cut off on the right.
Does anyone know how to correct that, is it related to the same flex cable or is there something else I disturbed?
mine will fade to white.. then i just push the power to put it in standby, then push power again to wake it back up and back to normal.. it rarely does it but still annoying...
If You Ordered From At&t
I had this problem about 2 weeks ago!!!!
I thought it was a fluke!
Anyway, walked over to 43rd and Lexington (NYC FOR THOSE WHO DON'T KNOW THAT MANHATTAN IS THE CENTER OF THE WORLD)
and they gave me the EXCHANGE HOTLINE for at&t.
I called them up, told them my screen is fading to WHITE and the lady sent me a new or referbished phone.. i dont even know.
Just so you know, i ordered my phone on AMAZON with a new activation. its covered under the MANUFACTURERS warentee for a full year from the date of purchase... so is the REPLACEMENT PHONE... but not from the date of replacement, just the date of purchase.
did anyone get deeper into this yet? I got a 8500 (need those without camera) from ebay USA, already with white screen. After reading here, that this is mostly an issue with connectors, I bought it, disassembled it and reassembled it, though still white. Should I give the contacts a treatment with contact-spray? (there's a tuner spray that doesn't leave residues) Or is there something broken within the ribbon cables? Seller said it has been dropped (but he also said, he didn't want to open it, while it clearly has been opened, one screw missing and warranty seal gone). It ssems to boot up normal otherwise, I hear a sound after the boot process, so probably this isn't a software issue?
Edit: another thing I noticed: When I run it without any keyboard connected at all, it's also white. I then connected the dpad again, and I could see a hint of the at&t logo in the lower part of the screen. When I pressed around on the back of the dpad a bit, all LEDs would go on/off... Sound to me like the dpad has gone bad, possible?
Edit II: Got it. Using a 20x eyeloupe I found that the PCB of the DPad is broken under the little chip on it. Now I just gotta find a dpad here in germany, but I assume those Hermes' are all equal...
hello
where can I get manual (if there is one) for disassembling hermes. link in wiki does not work.
thanks
this worked good for me
http://inuchanbt.blog54.fc2.com/blog-entry-100.html
Anyone know if this applies to the 8125 as well? I've got a flickering white screen. I had dropped my phone a few weeks back and cracked the LCD. Replaced it with an OEM LCD - it worked fine for about 2 weeks and then just suddenly went all white. Phone still works, I can still get calls - just can't see who is calling.
I don't recall that the wizard had the same problem... Though from a logical point, it seems that there is an issue behind white screens and the thumbpad being responsible for it, so it may well be the same thing. Perhaps just disassemble the wizard (there should be a howto too) and check if theres a similar connection from mainboard to thumbpad circuit.
Is there a disassembling manual for a imate k-jam that anyone knows about?
Here's a website with a video manual i found useful...
http://viralelectronics.com/category/howto/page/2/
Figured out the problem...
The only reason I figured out the screen goes blank is because the motherboard loses connection with the screen when you slide the keyboard out...try this out and see if the screen comes back...
put the screen on sleep mode (no white screen)...then slide out the keyboard and tilt it a little hard after pressing on the screen and put the power on. if it doesnt work try again it might take some pressure and power to make it work...be careful not to put too much power but as far as I went, it's a very sturdy cell.
alternately, slide out the keyboard in sleep mode, and press all the buttons really hard and then try to press the power button (press more towards the space bar because that helps)...if any of this works and the screen comes back on even just for a second...follow the following
Go back to the person who gave the link to the site with opening the HTC instructions and follow through and clean the whole phone up from dirt around the screen and such...you dont need to put those rubber things or whatever it says to put on the screen...then when you are putting it back together, press hard on the wire connecting the touch screen to the motherboard. I suggest sealing it with a good tape...and then you are good to go! I did it but it had a few glitches...the screens contrast sometimes goes awry but it is still visible and responds to touch. Also, the physical buttons work as well!!
Good Luck and do it at your on risk.
Have any of you tried this? http://forum.xda-developers.com/showthread.php?t=321163
hope the best
i tried this and it worked for me. i also pressed alil hard around the d-pad and heard a pop. i think it poped back into place.
thanks
razor rc said:
i tried this and it worked for me. i also pressed alil hard around the d-pad and heard a pop. i think it poped back into place.
thanks
Click to expand...
Click to collapse
i still have this problem.
fixed my wsod
I noticed a few days ago my 8525 screen went white, rebooted and it went away. Today it came back, but would only go away for a few seconds and then back to white. After reading some forums I decided to check the connector. I took the phone apart following this site as a guide. I removed the connector on the board side and cleaned the contacts with a qtip and denatured alcohol. Phone has been perfect for the last few hours, no more white screen of death. I didn't mess with the connector on the LCD side, just the board side. I'm a computer tech and I found it quite annoying to disassemble, but I managed without causing any damage, however, I'd rate the job at about a 8/10 as far as technical ability.
Joey
warped0202 said:
I noticed a few days ago my 8525 screen went white, rebooted and it went away. Today it came back, but would only go away for a few seconds and then back to white. After reading some forums I decided to check the connector. I took the phone apart following this site as a guide. I removed the connector on the board side and cleaned the contacts with a qtip and denatured alcohol. Phone has been perfect for the last few hours, no more white screen of death. I didn't mess with the connector on the LCD side, just the board side. I'm a computer tech and I found it quite annoying to disassemble, but I managed without causing any damage, however, I'd rate the job at about a 8/10 as far as technical ability.
Joey
Click to expand...
Click to collapse
i agree that this is one of the first things to try in curing the white screen issue. Others may find their problem runs a little deeper and the contacts on the d/pad chip are broken. An improvised cure which may not be very permanent is to place a little padding on the surface of the chip as described here:
http://forum.xda-developers.com/showthread.php?t=321163
If you have appropriate heat gun equipment you can re-flow the solder on the d/pad daughter board - but remember to remove the sticky key pad layer or you'll cook it!!
I regret that I'm closing this thread because we have several "White Screen" threads and the questions and answers are being spread all over the place.
Please use this one for future posts:
http://forum.xda-developers.com/showthread.php?t=321163
Mike
Ok, im going to start not from the beginning beginning, but from where problems started.
Friday night, went out, I was writing an sms when somebody pushed me and i dropped my wiz, i picked it up, to find that the battery was gone, nowhere to be found, i did find the cover tho. i tried to look for the batt, but i was in the middle of the club so it wasn't that easy.. I knew that a friend of mine had a spare one so i didn't worry that much.
Sunday I got the replacement, tried it, no luck, it ran out i thought, but when i tried to charge it, nothing happened. Buying a new one is not that easy when you are in Argentina, and they are expensive, so i decided to jump sart it. good news: it worked, i could turn on the phone, so the battery is fine. bad news: it still doesn't want to charge!
I previously had problems with the usb, and i had to have it soldered again, pretty strong, but I thought that might be the problem again, so i disassembled my wiz. new problem: the power button broke, the tiny, tiny black piece fell off, AND I LOST IT! DOH!
Anyways, the usb is still soldered pretty strong, i don't think its gonna go loose again, so thats not the freaking problem!
So now, instead of the initial no-charge problem, i have a disassembled wizard, that won't charge the goddamn battery, AND a broken power button (tried to glue it, but fell off again and thats when i lost the piece).
Regarding the button, i've studied my options, what would you recommend and how would you do it?
option 1: turn on the phone with the soft reset hole, and remap the screen on/off function to another button.
option 2: replace the power button internal piece with the one from the voice command button (i never use it). i've taken a look and they seem to be the same, but i don't know if taking it off and soldering it back would work..
anyways, that leaves me again with my initial problem, and i do have an hypothesis. I THINK (because I THINK i remember this happening to me before), that the battery won't start charging until windows has started, and the jump star power the battery has is not enough to get it started (tried to tape it and leave it for a while to see if it charged a bit more, but didn't work, the phone turns on but goes out when loading, and since i've my wiz pretty loaded it takes its time to load).
So to try this out i would need a way to charge the battery manually, and i don't have access to another wiz to have it charged (my friend had a spare batt because his wiz is broken).
So, if you have a solution to this, ANY different solution, or even an IDEA, please give me a hint!
For what i've read, this are common problems, so there must be something out there.
Man, that's a bad thing
I'll try to help you as much as I can.
You are right about Wiz only start charging when it's on. After my N78 was stolen and I went back to the Wizard, the battery was without any charge for months... I plugged it and no red LED... Turned it on and, bingo, red LED and charging!
The voice command and the on/off buttons are the same, so (in theory) it would work 100% IF you were able to change their places (at least for me, it is impossible to do manually, never found any good equip here =\ )
With a lot of patience (and a small soldering iron) I would try to take the voice comm button off and place it where the on/off was.
For the battery, maybe someone here can point if there is a "battery charger" standalone device, or such a thing...
Good luck man
hey thanks for the quick reply!
i'm not thinking of doing it myself, i'm not not that precise nor is my solder, but i know a guy, same dude that fixed my usb. I like that idea more than the other, but i guess that remapping the screen on/off and using the soft reset button would be much safer.. i haven't made up my mind about that yet.
Weir thing about MY wiz, at least thats what i think happened to me last time my battery was completely discharged, is that not only the device must be ON for it to charge, but it needs to have WINDOWS already loaded, i know for most devices it's not like that, but i think thats how mine works, or at least thats the only explanation i could find!
btw, i love your case modding concept, and since i might have my wiz sitting for a while, i might go ahead and try something too! nothing as extreme as yours of course.. i'd love to see more updates on your project along with some guide to see what ideas i can take
slight detail while thinking my options.. if i was to remap the screen on/off function to another button, would i need to have the device in sync? or connected via cable? because when i had the usb soldered, don't know how nor why (all the pins seem to be ok) but the device won't be recognized by any computer, usb only works for charging (or used to work, at least, still haven't figured why it won't charge now).
If its only an app that i can load to the phone, once i have it working (that if i ever will), i can load the app thru minisd, BT or IrDa so that would't be a problem.. i haven's investigated that issue yet.
Hey jinxie, how's your Wizard?
If you're still stuck with the battery (I hope not), check this out...
I think this will solve your battery problem:
http://forum.xda-developers.com/showpost.php?p=4963547&postcount=5
That's probably to work, just be carefull with the battery's temperature. If it starts to heat, stop the process and wait it to get normal, then start again.
Good luck!
i tried keeping the wires attached to the contacts for a while, didn't think it'd work better doing it just for a little and then repeating the process, i'll try that!
yeap, i'm still stuck and i think i will be for a while, i have to solve the battery issue first (would be useless to do anything else if i'm not certain i will get it to work), then i have to decide what i am going to do with the power button, and then i might paint it, i'm thinking matte black, or maybe take some ideas from your project if you have made any progress at the time!
thanks for the tip, i'll try it today and i let you know how it went
development: phone DOES NOT turn on with the soft reset button as i thought, i was sure it did, but after jumping the bat once again, tried the wiring method (not repeating the jump start but wiring it directly to de device pins), and tried to turn it on with soft reset and dind't work, while it does turn on with the power button, wich is broken, so in order to turn it on i cannot have the phone assambled, wich means that in order to try to make it work, i will need to hold the battery attached with my hands, and it is a pain in the.. you know where.
update: i wired the charger i was using to jump start the battery to the pins in the wizard, then held the battery in place with my hand, with a small screwdriver i pushed the broken power button. wizard turned on, IT FINALLY LOADED WINDOWS, but don't rush, i then (with my MOUTH) connected the USB wall charger to the port in the phone, and removed the wiring, i was expecting the goddamn light to turn on and the screen to tell me that my phone was finally charging. I WAS WRONG. then i had to let go because my hand was killing me and it went off
and the damn thing refuses to charge! what could it be????????
2nd update: I AM MACGYVER !
i figured the wiring had given the bat enough power to load windows on its own, so tried once more holding everything together with my hand but without wiring the pins this time, and at last the amber light turned on!!! im so proud of myself lol
SO NOW: device works ok, charges ok, battery has enaugh power to load windows, WHAT CAN I DO ABOUT THE BROKEN POWER BUTTON? i know you can't remap the power function since its hardware, but the screen on/off function might be remapped. soft reset button DOES not turn on the phone, is there any other way of turning it on? or my only option is to take off the voice command button and soldering it where the power button should be?
well, found the little button part that was missing, glued it (yes, GLUED it), and it kinda worked, i had painted the casing already, so i assembled everything back again. i used a folded piece of paper to hold the button still so it won't fall again and i think it was too big cause now its kind of hard to press but i can live with that, what i cannot live with is NO SIGNAL.. i mean, CMON!! are you kiddin me? now that the button works, battery works, phone assembled, and now this?? when i dissassembled the phone i forgot to take out the sim card, so the metal parts that hold it opened a bit, but i pressed them back, the sim in no way loose, so i guess i might have screwed the attenna :S
i've just checked, i can see the sim contacts so... [CENSORED] !!!
also now the screen looks weird.. like if it had less colours, like when you format your pc and haven's installed the graphic drivers yet, 3d effects look funny..
Hey man, have you painted ALL the Wizard parts, on both sides?
'Cause there is one that has a piece of copper board inside. It makes contact with the antenna. Without that contact, you'll never have signal
The piece I'm talking about is the one that has the camera protection, saying "1.3 MP camera". Look at its back and see if there's no paint on a green and golden plate. Remove the paint if it got there (the golden part is the important one, since it makes contact with the antenna).
Good luck man!
hahah lol, no of course i didn't paint both sides! but anyways im gonna take it apart again, clean it, and try again..
done. it had some paintng yes, but they were very tiny spray drops, so i don't think that is, anyway i cleaned it. On the other hand, i found that the antenna is loose on the left side :S what can i do about it?
So I have an issue with a 2012 N7, warranty is long gone. I've tried all suggestions from billykxda's thread, but no luck thus far. I've also tried Google's official page on the topic as well.
I've left the device charging for many consecutive hours, both via AC power and USB, and I suspect my issue resides with the LCD screen. Also tried a hard battery pull. It's also important to note that I haven't undertaken any mods on the device at all, i.e. the bootloader is still locked and USB debugging is not enabled yet.
When I plug the device into my PC the Win7 driver notification bubble pops up, usually reporting either an Unknown Device or an "APX drivers not installed" message. I'm unable to get it to boot into Fastboot, Recovery, or Android OS. Plugging/unplugging the device via USB yields these driver messages over and over again, along with the Win7 sound notification, so the device isn't totally dead, but no amount of button combinations or 30-60+ second button holds are getting any response.
Has anyone else experienced these issues before? Do you think my device is totally dead?
AvidPhisherman said:
Has anyone else experienced these issues before?
Click to expand...
Click to collapse
Yes; I am also experiencing similar issues. Unfortunately, I have not reached a solution. I just replaced a broken screen for a friend. Once I got the screen in, I tried turning it on but didn't see anything happen. I began to research and thought I had the dead battery issue that most people get when leaving it unplugged for an extended period of time. I plugged it in using the wall adapter for a few hours, used the power+volume buttons and still didn't get any response. Finally, I decided to charge it with my PC. The PC recognized something was plugged in, installed drivers, and now I have a Nexus 7 in my connected devices list. While connected to my PC, I hold power+volume down and hear the USB disconnect, reconnect, and have an unrecognizable device attached. This leads me to believe that the Nexus 7 is working properly and the screen is not working. I have taken the entire device apart to re-seat all connections 3 different times and still cannot get it to work. I hope someone can shed some light on our issues!
Edit: I forgot to mention, I also tested the battery with a digital multimeter. It reads approximately 3.79 volts DC. I thought it may be important to state this in case the issue is battery related. I'm not certain what the correct value should be for it to work properly.
I am currently trying to diagnose this problem. Yesterday, I hopped on Craigslist and bought a working Nexus 7 for 50$. I am currently taking it apart to rob parts from it and figure out where the problem is. So far I have tested the battery. The battery reads approximately 3.78 volts DC so I can probably rule this out as my problem.
Also, I noticed something strange yesterday. I took the broken Nexus with me when I went to meet up with the man selling the used/working Nexus. While I was outside in very bright sunlight, I pushed the power button on the broken Nexus. I noticed that I could actually see the screen doing something. It was all fuzzy and had lines running every where, but you could in fact see it doing something. I think the replacement screen I received is bad, but I won't know until I start swapping parts.
AvidPhisherman, for now maybe try taking your Nexus out in very bright sunlight and see if you can see the screen do anything when you press the power button. Also, I'm not trying to hijack the thread. It seems that we have very similar issues. I hope to find something that fixes both of our problems.
Success.... kinda. I tried combining the broken Nexus 7 motherboard with the working Nexus 7 screen but it wouldn't fit since one is the 3G model, and the other is the Wifi only model. Next, I put everything back together on the broken N7, but this time I used the LCD ribbon cable from the good N7. Success!!! It powered up, and I can see the screen. My problem now, is that the screen is mostly unresponsive and acts like you are touching it in random spots, when you're not touching it at all. I'm taking it apart to re-seat the connections... again.
__redfox__ said:
Success.... kinda. I tried combining the broken Nexus 7 motherboard with the working Nexus 7 screen but it wouldn't fit since one is the 3G model, and the other is the Wifi only model. Next, I put everything back together on the broken N7, but this time I used the LCD ribbon cable from the good N7. Success!!! It powered up, and I can see the screen. My problem now, is that the screen is mostly unresponsive and acts like you are touching it in random spots, when you're not touching it at all. I'm taking it apart to re-seat the connections... again.
Click to expand...
Click to collapse
Hey redfox thanks for taking in interest in this! You're not hijacking the thread, your posts are very helpful. Good to know I'm not the only one experiencing these issues.
I'm just a hobbyist with an interest in fixing things, although I don't have much experience with DIY fixing. I didn't have a chance to try turning the screen on under direct sunlight, but yesterday I took both my non-working Nexus 7s (the first one I mentioned in my OP, the second one just has a bad/hollowed out USB port) in to a repair shop for a free diagnosis. I'm actually a business user, my company owns the tablets but I'm responsible for maintenance/tech troubleshooting.
Please keep me posted with updates as to how your progress is going. I'll post again once I get a report from the repair shop re: my issues.
Hi,
I have been having the same problem,
I bought my wife a used Nexus 7 and it worked just fine for almost a year then all of the sudden the screen would not function
there would be lines going through it but it remain dark.
thank you for researching the matter i will try to buy the part online and see if i can get it to work now!
if i understand it correctly there is no need for a new mother board but just a new LCD ribbon cable?
godnessy said:
Hi,
I have been having the same problem,
I bought my wife a used Nexus 7 and it worked just fine for almost a year then all of the sudden the screen would not function
there would be lines going through it but it remain dark.
thank you for researching the matter i will try to buy the part online and see if i can get it to work now!
if i understand it correctly there is no need for a new mother board but just a new LCD ribbon cable?
Click to expand...
Click to collapse
I cannot guarantee that it will fix your screen, but it is possible. When I had this one out in the sun, it did the same thing. The screen was super dark, and I could see crazy lines. Hopefully a new ribbon/cable will fix your problem. They are only a few dollars on Amazon.com
godnessy said:
Hi,
I have been having the same problem,
I bought my wife a used Nexus 7 and it worked just fine for almost a year then all of the sudden the screen would not function
there would be lines going through it but it remain dark.
thank you for researching the matter i will try to buy the part online and see if i can get it to work now!
if i understand it correctly there is no need for a new mother board but just a new LCD ribbon cable?
Click to expand...
Click to collapse
__redfox__ said:
I cannot guarantee that it will fix your screen, but it is possible. When I had this one out in the sun, it did the same thing. The screen was super dark, and I could see crazy lines. Hopefully a new ribbon/cable will fix your problem. They are only a few dollars on Amazon.com
Click to expand...
Click to collapse
Hello fellow users! Quick update, I finally heard back from the repair shop.
Bad news - they tried swapping out the screen, then the battery, USB charging port, display cables, etc. etc. and nothing worked. Their diagnosis is that the tablet has a fried motherboard, and they're unable to repair and/or replace it
Good news - it cost me nothing to receive this diagnosis
Hopefully the outlook is not so grim for your respective N7s. Just wanted to post an update as to what I learned from this whole experience.
Hi guys, Reporting in.
Toke a while but i got the part AND found the stupid device!
After ALOT of fiddling, taking apart and putting back again i found out that the problem was the battery!
it looks like it was on its last leg and that caused all the strange screen stuff.
I dont have another battery to replace it so instead i hooked it up straight to a USB cable and into the socket and it works just fine
thanks for the tips and hopefully this helps someone else!