broken port tab - Nexus 4 Q&A, Help & Troubleshooting

so I broke the tab in the usb port in my nexus 4. I bought an induction charger but it doesn't seem to be charging the thing very well. It will sometimes turn on and I can see the battery is at 0% and it shuts down. do you think there is a chance there is a short in the port itself making it so that the battery drains itself? I left it charging overnight with no luck. What to do next? remove the port entirely while I wait for the new usb daughter board to come in the mail?

mikkowus said:
so I broke the tab in the usb port in my nexus 4. I bought an induction charger but it doesn't seem to be charging the thing very well. It will sometimes turn on and I can see the battery is at 0% and it shuts down. do you think there is a chance there is a short in the port itself making it so that the battery drains itself? I left it charging overnight with no luck. What to do next? remove the port entirely while I wait for the new usb daughter board to come in the mail?
Click to expand...
Click to collapse
I think it's more likely that the broken USB tab is causing either a short or has broken a connection the phone expects, which fools the circuitry into thinking the phone is plugged in to USB, which won't allow it to charge via Qi. You could try charging it with the daughterboard removed, but I'd be surprised if it works. Hopefully you have a back-up phone while you wait for the part, even if it's a RAZR V3 or Nokia 3310. SIM won't match, obviously, but you can probably pick up an adapter locally.

Planterz said:
I think it's more likely that the broken USB tab is causing either a short or has broken a connection the phone expects, which fools the circuitry into thinking the phone is plugged in to USB, which won't allow it to charge via Qi. You could try charging it with the daughterboard removed, but I'd be surprised if it works. Hopefully you have a back-up phone while you wait for the part, even if it's a RAZR V3 or Nokia 3310. SIM won't match, obviously, but you can probably pick up an adapter locally.
Click to expand...
Click to collapse
That makes sense. I do have an old samsung tmobile phone that lasts about 4 hours on its battery. I guess I might be using that for a few days. I'ts at home though and I'm at work. It would be nice if this thing would just work. I need to find a t5 torx wrench and scew it up more......

mikkowus said:
That makes sense. I do have an old samsung tmobile phone that lasts about 4 hours on its battery. I guess I might be using that for a few days. I'ts at home though and I'm at work. It would be nice if this thing would just work. I need to find a t5 torx wrench and scew it up more......
Click to expand...
Click to collapse
Some advice for someone who hasn't taken this phone apart yet:
First, go to ifixit and familiarize yourself with the teardown guide. There are also some youtube videos that are helpful (if you can't find them immediately, look for screen replacement guides.
Second, you'll need something thin and flat, and hopefully not with sharp edges. They make tools for this, but I doubt you'll be willing to order them and wait. Myself, I used the nail file from a keychain Swiss Army Knife. It's possible, even likely you'll cosmetically damage the plastic up a bit. If you have a hair drier (or even a heat gun), this can aid in softening up the adhesive. In any case, go slowly.
Do the disassembly over a fluffy towel. There are many tiny screws, and a fluffy towel will trap them rather than having them bounce away and disappear.
As I write this, another thought occurs to me. If you can, wait a few more days, but order yourself a new battery off eBay. Many sellers include the needed disassembly tools (including a T5 TORX, small Philips, and the plastic separating tools). Your Nexus 4 is probably 1.5-2.5 years old by now, which means your battery has had well over 500 cycles. At this point, you've lost upwards of 20% your battery's original capacity. Or don't wait, but order a new battery anyway and reopen the phone when you get it. The degradation of a battery is slow and one really doesn't notice it until that day you think to yourself "it seems like it used to last longer". Indeed, you may open up your phone to discover a puffed-out battery in desperate need of replacement anyway.

Planterz said:
Some advice for someone who hasn't taken this phone apart yet:
First, go to ifixit and familiarize yourself with the teardown guide. There are also some youtube videos that are helpful (if you can't find them immediately, look for screen replacement guides.
Second, you'll need something thin and flat, and hopefully not with sharp edges. They make tools for this, but I doubt you'll be willing to order them and wait. Myself, I used the nail file from a keychain Swiss Army Knife. It's possible, even likely you'll cosmetically damage the plastic up a bit. If you have a hair drier (or even a heat gun), this can aid in softening up the adhesive. In any case, go slowly.
Do the disassembly over a fluffy towel. There are many tiny screws, and a fluffy towel will trap them rather than having them bounce away and disappear.
As I write this, another thought occurs to me. If you can, wait a few more days, but order yourself a new battery off eBay. Many sellers include the needed disassembly tools (including a T5 TORX, small Philips, and the plastic separating tools). Your Nexus 4 is probably 1.5-2.5 years old by now, which means your battery has had well over 500 cycles. At this point, you've lost upwards of 20% your battery's original capacity. Or don't wait, but order a new battery anyway and reopen the phone when you get it. The degradation of a battery is slow and one really doesn't notice it until that day you think to yourself "it seems like it used to last longer". Indeed, you may open up your phone to discover a puffed-out battery in desperate need of replacement anyway.
Click to expand...
Click to collapse
Cool. I did end up ordering a new battery because of just that thought. It will be coming Friday though so I might not want to wait. I'll probably end up opening it up twice.. I also happened to open the phone about a 3 weeks after I bought it as somehow the screen cracked. I also have a heatgun. The phone is pretty old. I got it on release.

Related

Charger tip broke.

Hello everyone.
I seem to have a bit of a problem. The tip of my A500s charger, the end going to the tablet, seems to have broken in half....while inside the tablet. So now there is a bit of charger stuck in the port...and I cant conceive a way to safely extract it. It still charges if I plug the other half of the charger in so the situation isnt dire, but it is a bit touchy with how it must be positioned. Anyone have any idea how I can get that thing out of there...?
Sent from my Eclipse'd DROID X2!
Long nose tweezers:
http://www.aimdistributor.com/bnw/images/needlenose-overview.png
Good luck!
Zeravnos said:
Hello everyone.
I seem to have a bit of a problem. The tip of my A500s charger, the end going to the tablet, seems to have broken in half....while inside the tablet. So now there is a bit of charger stuck in the port...and I cant conceive a way to safely extract it. It still charges if I plug the other half of the charger in so the situation isnt dire, but it is a bit touchy with how it must be positioned. Anyone have any idea how I can get that thing out of there...?
Sent from my Eclipse'd DROID X2!
Click to expand...
Click to collapse
Yeah, and when it eventually breaks a bit more then it won't charge at all :S I'd definitely try to get it out. As the other guy mentioned, you could try tweezers. Another thing you could try is use some long, slim object and attach a SMALL drop of superglue to it, stick it carefully to the stuck part and watch that you don't get glue anywhere else, and wait for it to dry. Then just pull it out. I've had to do that myself to a few devices and it usually works great, the problem is just finding something slim enough.
Zeravnos said:
Hello everyone.
I seem to have a bit of a problem. The tip of my A500s charger, the end going to the tablet, seems to have broken in half....while inside the tablet. So now there is a bit of charger stuck in the port...and I cant conceive a way to safely extract it. It still charges if I plug the other half of the charger in so the situation isnt dire, but it is a bit touchy with how it must be positioned. Anyone have any idea how I can get that thing out of there...?
Sent from my Eclipse'd DROID X2!
Click to expand...
Click to collapse
Early on mine broke, and the pin inside the tablet got stuck on my charger tip. Had to send it in for repair (covered under warranty). To be honest, I've yet to see a worse charger design than the A500. The Thrive has a laptop charger and port.
WereCatf said:
Yeah, and when it eventually breaks a bit more then it won't charge at all :S I'd definitely try to get it out. As the other guy mentioned, you could try tweezers. Another thing you could try is use some long, slim object and attach a SMALL drop of superglue to it, stick it carefully to the stuck part and watch that you don't get glue anywhere else, and wait for it to dry. Then just pull it out. I've had to do that myself to a few devices and it usually works great, the problem is just finding something slim enough.
Click to expand...
Click to collapse
Are you MacGyver?
Thanks for the replies everyone! That superglue idea is nothing short of genius!
Sent from my DROID X2 using XDA App
same thing happened to mine less than a month after owning the tablet. i just stuck the charger in and pressed it towards an edge as i pulled it out. it brought the little piece out with it. ended up having to buy another charger. from day 1, i knew the included charger wasn't good news...
this happened to mine also, and i pulled the pin out from the inside and the new charger doesn't fit, and i'm thinking that i was suppose to pull it out, anyone can tell me? or show a close up of the hole, my warranty ends this month and hope they cover it. thanks.
I've used the superglue trick to extract a dime from a seatbelt receiver in a car. Use the glue sparingly, let it set, and it can work. SPARINGLY. If you have to do it again, so be it. Better than too much and causing new problems.
The same thing happened to me. I was able to get it out with a tiny screwdriver and a little patience. I bought a replacement directly from Acer. Buy the one for the A100. The wire is longer than the stock one and I haven't had a problem with the new one.

Galaxy Note Inductive Charging Mod

I modified my Galaxy Note to use inductive charging via a palm touchstone / patch.
Just a quick note. Not a whole lot to contribute here, because I largely followed the examples of the Qian Qi. That guy is awesome.
I don't think I voided a warranty, either. Only minimal teardown required (black plastic back, then the speaker section). Never came across a sticker I had to remove....
Useful links:
galaxy s inductive charging mod
evo 4g induction charging mod
galaxy note teardown video
galaxy note teardown pics
Notes:
- Buy a good soldering iron. Weller WESD51, set to 610 deg F, with 1/32" long conical tip, with lots of flux and lots of flux remover are the only reason I could do this. I can't stress enough the value of having good temperature control, knowledge of temperature, and so forth. I stumbled around with an "ordinary" soldering iron for a long time, and in hindsite, I can't believe I did so.
- Do not choke on the price. I already had a lot of soldering gear, and I bought $220 more. Spend the money. It's worth it.
- Watch the curious inventor youtube videos on soldering. This guy. Watch everything, several times. http://store.curiousinventor.com/
- You want 30 gauge wire. It's the only thing that just barely can be crammed in. I used the "Kynar" coated type. Buy at least 2 colors.
- as you look at the phone disassembled, with speaker on the bottom left, the +5 pin on the micro usb (MHL) port is the leftmost. I attached a wire to that, and a ground wire to the housing where the port was soldered.
- routed the wires under the speaker, then back, then into a VERY slight indentation into the battery compartment. used a blue "safe open" tool to help shape the wire / crimp ends. Once in the battery compartment, you're golden. Attach the inductive charging coil to the back of the samsung plastic back, add solder to the pads, and attach the wires.
- Attached is a picture with roughly how I routed wires. Red is +5V, Blue is ground. Be sure and double check if my recollection is right where the indentation is into the battery compartment. (that part is by memory).
- dont leave too much slack. it's really hard to get the samsung black pastic panel back on. Mine very slightly bulges.
- be careful where you put the charging sticky patch, because this phone is a little bit bigger than a palm pre. You have to consider if the phone can sit on the charger and "lock in" with the magnets. If you place it too high, it actually can't (in portrait)!
- Qian Qi had a really interesting point: most articles about how Li-ion batteries behave are wrong, and fully discharging the battery drastically reduces the number of cycles you have. So this is actually a very useful mod--whenever you don't use the phone, toss it on the charger.
Thanks for summing it up! Was actually thinking of doing this mod myself. Question: do you have a protective case on your Note? If so - what kind and how badly does it affect the magnetic properties?
No case. Especially because the note is so big, I think it would be unmanageable.
I took the samsung thin plastic back, and placed the Palm PRE (with charging coil still attached) on top of it, on the touchstone -- to figure out proper placement & mark with a pencil. I noticed a buzzing sound, coming from (I think) the induction coil on the palm pre back itself. I suspect if you use a case, this wont work well.
Also, the size/weight/placement of the galaxy note are such that the magnets are just barely strong enough to hold it. One time my phone was near, but off, the charger. I'm not sure if vibration from the phone did that, or my kids
In summary, I'm not sure how well it would work with a case. You might be able to research this on the net; among the 15 or 20 people that have bought a Pre, you might be able to find some info about the effect of a case on inductive charging.
tight squeeze?
im wanting to try this mod i have my touchstone on the way not thank you amazon but it seems like to me that the pad from the pre wouldnt fit under the cover of our phablet =/ could you post pics of the finished product and i think this is the only instance that i have seen someone attempt this with the note and i want to try it i love my note but would love it even more with inductive charging.
I am not the original author but I performed a different Touchstone mod and posted pics here:
http://forums.androidcentral.com/sa...1-galaxy-note-touchstone-mod-photo-heavy.html
Hope it helps!
-darren
Sent from my GT-N7000 using Tapatalk 2
Thank you!!!
Thank you so much for your post I have my materials on the way but I hadn't seen a detailed guide for the note other than this one and was worried I would have to solder directly to the usb pins which looked scary lol I did have two questions though would your mod work the same way for the at&t note? Specifically the points where you soldered to the phone and can wireless charging be performed through a case?
Hey, OP here. You may want to hold off just a bit. Mine is exhibiting some issues now. As in, it says "charging" but it doesn't do so wirelessly. The phone will stay "charging" but the battery % never goes up. (It was slow before, but would charge fully over a night).
Charging via USB still works.
It may be something simple; I'm not sure. But I need to crack it open and take a peek, and I haven't had time to do that yet because my phone is functional at the moment.
If nothing has conspicuously changed, there may be something about the design that isn't sustainable. Or maybe my solder joint halfway broke, or one of the wires got smashed enough so that it's partially broken...
I'll write back with my findings. Bug me if I don't
Thanks for the notice I was about to pull the trigger lol tbh I probably shouldn't attempt this I've never done a mod like this before and I'm not exactly a surgeon with a soldering iron lolvthatvbeing being said I'm going to attempt this on an old evo 4g I have before I do surgery on my baby lol plus I'm already familiar with the guts of an evo from screen repairs ill report back with my results
Sent from my SAMSUNG-SGH-I717 using xda premium
Success it took some doing but I got it I haven't done the mod on my note yet but I did it on my evo last night and it works its rough I haven't cleaned it up yet but I'll post the pics I got this mod from www.goodandevo.net
Sent from my SAMSUNG-SGH-I717 using xda premium
Thank you for this post.
Sent from my SAMSUNG-SGH-I717 using Tapatalk
No prob I just wanted to see if i could do it and if I can do it with little soldering experience I'm sure most could do it I haven't done this mod to my galaxy note though as there is way less room in its a far more complicated mod than the evo because you have to make room for wires in a device samsung made as thin as possible and the way you have to route the wires I feel like the solder joints would just break
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
For those who want to try this out but still have warrantee just buy a backcover, a micro usb plug and assemble it according to the directions here.If you need the note just take out the usb plug and the back cover and you're good to go.... Or leave it there.....
For those who don't know what pins to use on the usb plug:
Pin: 1 is 5V+ (red)
Pin: 5 is GND (black)
Works like a charm.......
becosemsaida
Cool mod! Does it affect the stylus operation though?
pboesboes said:
Cool mod! Does it affect the stylus operation though?
Click to expand...
Click to collapse
yes it affects the stylus sometimes it reacts with delay and sometimes it clicks although only hovers over it
pboesboes said:
Cool mod! Does it affect the stylus operation though?
Click to expand...
Click to collapse
I was not a big stylus user; I can't stand the input lag. I didn't notice a difference, but I always considered the input speed unacceptable. Not sure why there would be any difference, anyway.
My big problem that I've never taken the time to address is that after some time, it's as though I can't pull enough current through the wires to charge. One day I need to crack this open & figure out why.
gr8 n interesting post
wonder how fast can a full charge be completed
regards
strategist99 said:
gr8 n interesting post
wonder how fast can a full charge be completed
regards
Click to expand...
Click to collapse
It is slower than normal, but completed in a night. I still have not dismantled my phone to attempt to repair this, but I want to soon

short circuited my note

Hi everyone,
First of all, I apologize in advance,
1. Because I know this isn't a tech support forum.
2. Because I don't contribute and help out as much as I should.
Coming here was a last resort, I don't consider myself a noob, but I'm really stuck here.
Please note that I appreciate every single response, and I will donate if anyone can give me a fix.
With that aside, let me get started
__________________________________
Okay so about a week ago, I accidentally bent my charger when it was charging my note.
It didn't charge at all that night
That morning, I blew into the charge port on my note, suspecting that dust may have been the cause.
Somehow, that helped, as my note charged fully that day, in about 2-3 hours
Then I tried charging it the next night.
It charged incredibly slowly, reaching about 70% after 10 hours charge
The next few nights were similar, but reaching no more than 40% charge after 10 hours.
It got progressively worse, it would only charge if I applied pressure to the mini-usb,
I looked around this morning, and stumbled across another guy with the same problem
(see here http://www.galaxynoteforum.net/galaxy-note-help/charging-port-issue/ )
He advised,
"Well I have figured out the issue. If you look into the charging port slot on the phone you will notice a small thin flat piece of metal which inserts into the charger. That was slanted and angled downward which would not let "ANY" charger or docking station charge correctly also causing it to drain the battery. Contacts on this piece and the phone were to close causing a minor contact draining power. I used a precision flathead screw driver and lifted the piece slightly and now works fine"
So I tried that, and it seemed to help, as the note began charging, (extremely slowly, reaching about 30%)
Then I tried pushing that "thin flat piece of metal up even further"
However, I went too far, and I couldn't fit the charger into the charge port.
So I tried pushing it back into the centre but I may have damaged one of the pins in the charge port (inside the phone)
I seen a little spark, and the note turned off.
I tried switching it on, and managed to boot to safe mode (no idea how)
So then I tried charging it, I applied pressure and managed to get it to start charging. (thank god)
This was about 30 mins ago, it looks to be holding the charge at about 20%, but it's not increasing
-----------------------------------------------------
I suspect one of the pins in the note charge port was snapped off.. although I'm not sure.. (it appears to be the one on the right)
1.Does anyone know how many pins there are on the charge port inside the note? (is it 4 or 5?)
2.What should I do?
If I broke a pin, it should not charge at all, right? (but it seems to be charging)
3. Do I need to replace the charge port, if so, how much would it cost?
4. Would I be better off getting a charging station, and charging the battery using that
5. Should I try moving the metal strip again? (inside the charge port of the note)
oops forgot to mention, when the problem started, and the note was slow-charging, an audible buzzing/humming could be heard in the wall outlet
also, I'm using my original samsung usb charger, not a generic one, and I'm charging directly into a wall outlet.
------------------------------------------------------------------
Thank you for taking the time to read this, I really appreciate it, and any advise that you do offer.
Cyber735
Here my tipp: You can go to a service center, maybe they even repair it under warranty. Or you can order a new micro usb port and replace it. Google should help you to find a seller. Depends on whether you feel comfortable enough to replace it yourself or not. Oh one more thing, I would stopp using your Note to avoid any further damage.
Sent from my Galaxy Note running ICS
there are 5 pins on the charger slot, 4 I believe are for data transfer and the 5th being the one that draws power (charges the phone)
Have you tried transferring data from PC to Phone and see how that pans out ?
Its possible to replace the USB port, Ive seen a few threads about this on XDA, A quick search should chuck out some results.
But as mentioned above, Try to claim under warranty first, if you have it, or pay the Service centre to do it if you dont feel confident enough to do it yourself.
I think I recall someone with a similar issue and it cost him / her $60 for USB replacement (convert that in to your currency)
If you have a friend with a Note or a phone that fits the Note's battery you could always charge your battery in that phone and place it into yours until you get it fixed.
IF YOU MUST charge your Note ( you could if you intend to get a new USB slot) I would suggest to charge only via USB - as in charging from your PC / Laptop / TV / PS3 etc. As this will not draw as much current as it would coming directly from the mains supply!
Good luck on getting it fixed, And please keep us posted with the results !
http://pinoutsguide.com/PortableDevices/micro_usb_pinout.shtml
check this out. It gives the pin configuration. I am no expert but hope it helps!
altae said:
Here my tipp: You can go to a service center, maybe they even repair it under warranty. Or you can order a new micro usb port and replace it. Google should help you to find a seller. Depends on whether you feel comfortable enough to replace it yourself or not. Oh one more thing, I would stopp using your Note to avoid any further damage.
Sent from my Galaxy Note running ICS
Click to expand...
Click to collapse
r
Thanks for the quick reply!
First of all, I can confirm that no pins are broken or bent, everything looks normal, it also seems to be charging better, as I centred the metal strip in the charge port.
As for warranty, well I didn't purchase any extended warranty or insurance, however, the standard warranty lasts 2 years.
Unfortunately
The Repair Warranty Exclusions are as follows: (i) Subject to the inclusions of the applicable manufacturer's warranty, a mobile that has broken down or is damaged as a result of: (a) abuse or tampering, (b) electrical damage, moisture, dampness, oxidation, corrosion or food, dirt or liquid ingress (c) accident, neglect, impact, actual or attempted theft, fire, power outages or surges, or incorrect voltage, (d) transportation or packaging (e) removable batteries or damage caused by battery leakage
Basically, the only thing that I'm covered for is "handset breakdown"
My phone is in perfect condition, and no pins are broken or bent (as discovered on closer inspection)
So do you class charging issues as "handset breakdown" or not?
I may purchase a new charger, just in case the issue is with the charger, and not the phone,
What d'ya think?
Thanks again for the quick replies azzledazzle & nipuna, I didn't notice them until now,
Yeah I'm 90% there's no damage to the pins on the charge port, and it seems to be charging now, slowly at least,
I've centered the metal strip as best as I can, (inside the charge port)
I'll leave it to charge now for a while, as I'm not sure if it's fixed or not
Then I'll try another charger if it doesn't work
If all else fails, I'll try getting it repaired under warranty
(although that's more of a last resort, as it will take a few weeks to get my phone back)
does anyone know if the standard galaxy s2 charger will work on the note?
I don't have it on me now, although I could borrow it from a friend
I know its an official samsung charger, although not sure if it's the usb or the other kind.
I'll let it charge for a while, then I'll try transferring data from the laptop, to make sure the pins are fine,
thanks for all your help everyone,
1st of all: if you go poking around in the usb port with a metal screwdriver, take out the battery first. Not only will it avoid shortcutting and maybe blow a fuse inside the phone, but it will also protect you from an exploding battery when shortcutted !
S2 charger will work
Sent from my GT-N7000 using xda premium

Preventing stress on micro usb port...?

I swear for as smart.and.as great as this phone is, the easiest things to fix which pose the biggest.problems arent.fixed. Having the phone plugged.in.while using.it in landscape creates huge stress.on the port. So much that the cable gets looser as the pins are bent. Stupid samsung with their.idiotic location for.ports, but I.digress... has anyone found a longterm fix for this? . I thinking like a plastic moount that clips.to.
The bottom of the phone and.encases the beginning of the charger cable to prevent any stress in any direction? My temporary solution is I rubberband the beginning of the cable in a few loops as if I have it zip tied. This prevents any minor tugging from directly pulling the port.
First of all new USB 3 port cost about $14 and could be replaced by user in about 30 min even if you don't have 1 yr warranty. You can use any USB 2 wire to charge Note 3, some are much thinner and more flexible, than the factory cable. And with at least 6 hours screen time I can't imagine running out of power before night, when I put it on charger and go to sleep, but I do have full time job and little kids so actually never had a chance to use it for 6 hrs in 1 day anyhow. Maybe you need bigger battery and if you don't like Samsung design maybe another phone, I don't see anything wrong with it, otherwise would not buy it, heard Apple is a popular brand, but never actually used it.
pete4k said:
First of all new USB 3 port cost about $14 and could be replaced by user in about 30 min even if you don't have 1 yr warranty.
Click to expand...
Click to collapse
I hate giving a reply that doesn't really help the OP, but I can somewhat sorta agree with this comment. Sorta.
Because I got the Note 3 now but haven't broken its port yet.
However I did have the Note 2 and the Galaxy S2 and there was that issue if you're careless. Sloppy plugging and stress, sometimes a few drops of water falling on the port too and shorting it, etc. Anyway, I'm very unskilled and clumsy regarding basic electronics repairs but still managed to replace the USB board on the S2 with Ebay parts. It was less than 20 USD, the board and a kit of screwdrivers. It really is very easy to replace that part if you damage the USB port (getting the infamous "charging / not charging intermittent warnings, even when the phones are not connected to anything).
I seriously doubt the N2 or N3 are much more complex. (I used repair videos on YouTube for the S2, I'm sure they will pop up for the N3 if relevant)
Not so with other components (Screen, for instance). So take some care with it and don't worry too much because even home-repair is fairly accessible and cheap in that case.
Okay let me paint you a picture..I play aot of poker. there is an outlet under the table so I have my phone plugged in sitting on the rail behind my chips as I either watch 24/7 movies or play games.but since my phone is horizontal, naturally gravity works its magic and puts pressure on the port. not only that, but the less slack I have the more pressure is applied.
so as you can see my circumstances are very specific to my regular usage of this device. hence I utilize rubber bands.sometimes.
If you guys are really concerned about the usb port on the phone being damaged, maybe something like the qi wireless charger can help.
Or maybe buying a spare battery.
Or buy a right angled usb cable
Sent from my IdeaTab S6000-F using XDA Premium 4 mobile app

Replace internal Charger Port Cable?

This phone did, intermittently, work. But it also behaved as though there was a short somewhere in the system. Now it will not power on, and I am making a leap of logic and assuming that's because it cannot charge the battery. (I've tried every single suggestion here re powering it back on, so let's move past that option.)
I note that on ebay and elsewhere there are internal charger port cables (3rd party unfortunately) that are inexpensive (as low as four or five dollars, or eight dollars for one with a small tools set). Has anyone ever used one of those third party internal charger port replacements and had success?
Thanks in advance.
Okay, I have gone ahead and ordered one of the internal USB ribbon assemblies for my OnePlus 2. But I haven't seen anyone else discuss having actually done a change-out of this part. Isn't there any hardy soul armed with spudger and screw driver who's attempted this?
shonkin said:
Okay, I have gone ahead and ordered one of the internal USB ribbon assemblies for my OnePlus 2. But I haven't seen anyone else discuss having actually done a change-out of this part. Isn't there any hardy soul armed with spudger and screw driver who's attempted this?
Click to expand...
Click to collapse
i replaced the charging cable it is easy quick fix, ordered one from aliexpress
arjan.bongers said:
i replaced the charging cable it is easy quick fix, ordered one from aliexpress
Click to expand...
Click to collapse
If you don't mind me asking, did the phone work at all right before the replacement? Mine is a dead as a doornail, which is why I wonder. The fix does look to be easy (I watched some videos and even removed the old one, so the new install is all ready to go).
shonkin said:
If you don't mind me asking, did the phone work at all right before the replacement? Mine is a dead as a doornail, which is why I wonder. The fix does look to be easy (I watched some videos and even removed the old one, so the new install is all ready to go).
Click to expand...
Click to collapse
He didnt charge thats why i replaced the connector. but the rest of the functions were normal
arjan.bongers said:
He didnt charge thats why i replaced the connector. but the rest of the functions were normal
Click to expand...
Click to collapse
Well, we shall see if that solves my completely non-functioning phone issues or not. Perhaps this thing is just dead. My ebay seller is behind schedule as far as delivery goes, but again I will post here whatever the outcome once I do replace the usb port and ribbon.
I did promise to post a video of my install. I do not know if this worked yet (charging a newer battery; if that doesn't work I'll go back to the old battery and try again). But here is the video, which I ended up sorta having fun doing.
https://www.youtube.com/watch?v=INZUBsXXTFE
Well, I'm marking this down as a fail. The install was easy, but the phone remains dead, dead, dead. Not a whiff of life to it. The short, if it is a short as I suspect, may be in either the motherboard or daughterboard. So, not being one easily driven off by failure, I bought a working but very bent up OP2 off ebay for 70 bucks. The idea being to take its innards out and put them into the frame (and the I think working screen) of the one I have. I'll look either brilliant or the fool (I play the second one better). I will, as usual, report back.
So... said I'd follow up on the $70 ebay phone buy (the phone very bent up but somehow still working). I did get it, tested it (it did work but screen was under obvious pressure due to bend), then removed the motherboard, usb ribbon cable, and daughterboard from it and moved them into the non-working phone I was given by a friend. And it worked!! I now have a OnePlus 2 phone which is updating the rom at this moment. I'll probably root it and put a custom rom on later, but for now I just wanna see what the phone is like with the standard setup. Anyway.... it was fun to take a phone apart (2 phones, actually) and succeed at the end.

Categories

Resources