g2 display water damage, which part to replace? - G2 Q&A, Help & Troubleshooting

my d800 was immersed in the pool for a few minutes.
tried heating it with a hair dryer immediately. then left it in rice for a couple of days.
after charging for a little bit, i hit the power button. phone turned on like normal, but lcd was all messed up.
it was like distorted rgb dots all over the screen. and there was no haptic feedback to my touch.
the phone functioned perfectly - ringtones, led notifications, etc. only, i couldn't see anything.
i left it off for a couple of weeks, and switched it on again today. the display is only black now, but i can see it is backlit, compared with when the screen is off. and the phone vibrates now when i touch the screen.
so i'm guessing the digitizer works?
looking to repair it myself, whatever might need replacing.
any ideas, guys, on what i have to change here? or just leave it like this and hope it eventually works again? :laugh:
also, suggestions or links for items and instructions that might've helped you will be much appreciated.

Related

Touch screen stopped working :-(((

Hi,
The touch screen part of my universal has ground to halt to the point that it won't work.
There doesn't appear to be any cracking and I don't recall dropping it or sitting on it.
I work a fair bit outside and can get quite a bit of dust and dirt in my pockets and am wondering if it could be due to dirt getting into the connect on the hinge.
Has any one else come across problems with the hinge?
I'm reasonably adept with a screwdriver - are there any things to watch out for when disassembling to check it over?
Hi..
If u can open with the Universal guide posted in the forum then try clean ing the connectors on the Right and Left of the Clamp Shell part with Iso Propyl Alcohol.
Before opeining you can try pressing mildly with yr fingers, at all the forur corners..it can start working..else do the above...
Hi,
OK, the screen seems to be working OK this morning, however I seem to be getting a sort of ghost effect where it appears as though the phone icon and the volume icons are getting pressed resulting in the volume controls and the phone/flight mode popup appearing on screen.
I guess it is all down to dirty connections.
Do you have a link to the thread about dismantling the hinge, I can't seem to find it.
Thanks.
re isopropal alchol
only use 99% alchol to clean contacts anything below that can cause corrosion on printed circut boards and contacts.
any progress yet.
mine stopped working today too.
but when i took off my screen protector, it worked for a while.. now its dead again.
I think the screen protectors may cause this problem, as I too had this problem with a screen protector; but when i took it off it would work and and off. I cleaned the screen up and after a few hours my screen was working again!
being in Australia I go to the beach allot. with my jasjar.
the sand gets stuck in the sides of the screen putting pressure on the screen and disabling any input. just a thought that it could be the same with u.
hope u sort it out, otherwise claim it on warrenty sooner than later.
The problem I have with the screen is that occasionally the touch screen side of things appears to stop working and also the the volume, wifi and phone dialogs keep on appearing as if I am pressing the relevant icons in the top bar.
I'm guessing some dirt has got into it somewhere or there is a loose connection, but am struggling to open up the screen's case to inspect it.
6680abhi said:
I think the screen protectors may cause this problem, as I too had this problem with a screen protector; but when i took it off it would work and and off. I cleaned the screen up and after a few hours my screen was working again!
Click to expand...
Click to collapse
i took off my screen protector and it worked an hour...
got home, prepared to go to the T-mobile store.. then cleaned my screen ( without protector ) with a small cloth and it was working again.. so weird..
lets wait and see what happens ..
It's not really that weird: If some dust, or something equally small gets between the screen and the plastic frame, it can put enough pressure on the screen, and so the touch screen takes it as a constant (or intermitent) input, invalidating any other action on the rest of the screen.
I just received my Aquapac waterproof (and sand/dustproof) to use my Jasjar hapilly in the beach! :lol:
oh so annoying, my volume sliders keep popping up now..., as if some one keeps tapping, cause when not in Land scape mode when i open the "START" menu. it scrolls down, the same input/tap as wher the volume is in Landscape mode
There must be something wrong ... my screen still isnt working properly
one possible solution for touch screen not working
guys.... although I dont need to register onto this portal and it took me 15 minutes to register (fault of my own) but I got so much relieved with the solution that it deserved 15 minutes of my effort ;-) I hope it helps someone...just like it did help me....
I own a P835 Asus mobile and from past 2-3 days was having problems - start menu continuously appearing and my taps not getting recognized. Since yesterday my screen suddenly stopped responding to any taps or scrolls altogether.... buttons were working fine but not the screen..... i spoke to the facilities centre this morning and was about to take it to the shop but due to my laziness...didn;t go.....
Thanks guys.... what you mentioned above is very correct.... it was just a tiny molecule of dust that the screen was interpreting as my input and finally refusing all my taps..... I just cleaned the screen and the speaker side with the mere stylus n things started working.... thanks a lot.... more than laziness was this worry cause I just bought this piece a month before....
so people...before takin it to the shop....try this one too.....huhhh.....

Vogue replacement screen functions intermidantly

I am currently in discussions with the screen's vendor about the issue, but I figure somebody might have some advice to offer here too. I purchased a replacement screen for my Vogue after I cracked the factory LCD. Touch membrane was fine.
Opened the phone, pulled out the old LCD, replaced with new one, etc. At first, the "new" screen seemed to not power on at all - then after several cycles of open phone/test connections with old LCD/rebuild with new LCD I finally got the backlight on, yet the display itself seems to not be working. There is an ever so slight greenish glow in the bottom left corner of the replacement screen when the backlight was on.
Several hours later, during which time the phone just sat on my desk idle (but on) I hit the power button to turn on the screen and was dismayed that the backlight did not come on (simmilarly to how it was originally.) I am certain the phone was assembled correctly, all connections are secure, etc.
The vendor suggested adjusting brightness/contrast settings, which I skeptically tried to no avail with MyMobiler. So at this point, the backlight seems to work when it wants to and the display seems to not work well at all.
Has anyone else seen anything like this?

LG Nexus 4 - Washed in a Washing Machine(Still Working)

Hi, I accidentally washed my phone in a washing machine(don't ask why) on Friday. On Saturday I dried it out and when I tried to charge it the red light has shown. Yesterday the red light went away and there was a green light shown. The thing is, I can turn my phone on, I can take calls, I can feel the vibrations when I move my finger around the screen but it is completely black. So I would like to ask, is there a way to fix it? E.g. a new digitzer or something?? Thanks in advance.
If you get haptic feedback when you touch the screen, its not the digitizer. Probably just the screen itself. You can find a new one online, just google it or check ebay

LG G2 -- Screen brightness can't exceed 40%

Hello.
The other day my phone suffered a little water damage. Not submerged in water or anything, but a couple drops found their way into the phone. The phone was turning off/on and functioning, but the display was black. I could feel buttons being pressed and stuff...the screen just wasn't illuminated. Well, I left it alone for a while, and now the screen works to a degree.
It's functioning perfectly, except it can't go above 40% brightness or the phone's screen goes black. As soon as I move the slider at or below 40%, the screen works perfectly again.
Obviously whatever illuminates the screen is damaged to some degree. The same thing happens when using apps like Lux...so I'm pretty sure it's a hardware problem now. I'm wondering if anyone has any idea what exactly could be damaged so I can fix it myself, or have anything to try before taking it apart again.
Thanks!
macdaddyusmc said:
Hello.
The other day my phone suffered a little water damage. Not submerged in water or anything, but a couple drops found their way into the phone. The phone was turning off/on and functioning, but the display was black. I could feel buttons being pressed and stuff...the screen just wasn't illuminated. Well, I left it alone for a while, and now the screen works to a degree.
It's functioning perfectly, except it can't go above 40% brightness or the phone's screen goes black. As soon as I move the slider at or below 40%, the screen works perfectly again.
Obviously whatever illuminates the screen is damaged to some degree. The same thing happens when using apps like Lux...so I'm pretty sure it's a hardware problem now. I'm wondering if anyone has any idea what exactly could be damaged so I can fix it myself, or have anything to try before taking it apart again.
Thanks!
Click to expand...
Click to collapse
Did You ever get to the bottom of this?
Having the same exact problem?

[Q] screen doesn't work after water dmg

So my son got the tablet wet. I let it dry out for a few days then turned it on. Everything seemed fine. It went to home screen but the touchscreen was unresponsive. After about ten second's the screen went negative kinda then blank. It still vibrates and makes noise from notifications and volume buttons. But the screen will not work. Is there a screen replacement I can buy and would that work to fix my problem? If so is there also a video on how to do so? Thank you

Categories

Resources