Related
Okay where do I start...
I was given this phone from a friend, and it was working fine,
rooted and no problems at all...
Followed this guide to install the "Google Play Edition" ROM >> http://www.technobuffalo.com/videos/how-to-turn-a-galaxy-s4-into-a-google-edition-phone/
All was working perfectly, then in a backup process using titanium backup, the phone crashed...
I'm stuck in a boot loop with only the Samsung Galaxy logo screen.
I can enter Download mode, but not recovery...
Have tried every ROM that I can think would be appropriate to restore but to no avail...
Even tried philz touch recovery, nothing seems to be working...
Odin always reports either write failed or <ID:0/003> There is no PIT partition.
Have tried writing just the .PIT file from >> http://forum.xda-developers.com/showthread.php?t=2265477
Have tried to recover using Kies, firmware downloads then "Error - F" Phone cannot be located...
The phone gets stuck with a small dot of a process bar in download mode and this read out in the top left of the screen:
ODIN MODE
PRODUCT NAME: GT-I9505
CURRENT BINARY: CUSTOM
SYSTEM STATUS: CUSTOM
CSB-CONFIG-LSB; 0x30
WRITE PROTECTION: ENABLE
START [224, 1440]
ODIN: FLASH READ FAILURE
I'm at a total loss how to recover this, and if it's even possible to recover?
I would happily send it somewhere for repair, I have no warranty so i expect to pay, but no idea where to send?
Does any one have any advice or solution to this problem?
Much appreciated.
re: cannot get into recovery.
EvilM0narch said:
Okay where do I start...
I was given this phone from a friend, and it was working fine,
rooted and no problems at all...
Followed this guide to install the "Google Play Edition" ROM >> http://www.technobuffalo.com/videos/how-to-turn-a-galaxy-s4-into-a-google-edition-phone/
All was working perfectly, then in a backup process using titanium backup, the phone crashed...
I'm stuck in a boot loop with only the Samsung Galaxy logo screen.
I can enter Download mode, but not recovery...
Have tried every ROM that I can think would be appropriate to restore but to no avail...
Even tried philz touch recovery, nothing seems to be working...
Odin always reports either write failed or <ID:0/003> There is no PIT partition.
Have tried writing just the .PIT file from >> http://forum.xda-developers.com/showthread.php?t=2265477
Have tried to recover using Kies, firmware downloads then "Error - F" Phone cannot be located...
The phone gets stuck with a small dot of a process bar in download mode and this read out in the top left of the screen:
ODIN MODE
PRODUCT NAME: GT-I9505
CURRENT BINARY: CUSTOM
SYSTEM STATUS: CUSTOM
CSB-CONFIG-LSB; 0x30
WRITE PROTECTION: ENABLE
START [224, 1440]
ODIN: FLASH READ FAILURE
I'm at a total loss how to recover this, and if it's even possible to recover?
I would happily send it somewhere for repair, I have no warranty so i expect to pay, but no idea where to send?
Does any one have any advice or solution to this problem?
Much appreciated.
Click to expand...
Click to collapse
During your unsuccessful flashing of the google edition rom you have lost ROOT and the custom and or stock recovery.
That is why you cannot go into recovery mode.
You are lucky that the .pit file did not flash, you could have ended up with a brick (unusable phone).
The .PIT file is the partition information table, if that is changed or damaged you would need to send
your phone to samsung or other phone repair shop to get it fixed.
What you need to do is to download and Odin flash the stock-rooted i9505 rom which can be found here:
http://www.androidfilehost.com/?fid=23060877490003683
This rom is pre-rooted and you will be able to get into recovery mode without any issues.
Once this is odin flashed, be sure to make a nandroid backup before flashing other cwm/twrp zip file roms.
The "phone cannot be located" error most likely means that you either do not have the proper samsung usb
driver installed or you need to check the usb cable connections to your computer and phone.
Perhaps use a different usb cable and a different usb port will fix this issue.
Just in case you need it, here is the link for the official usb drivers for the samsung s4 phone:
http://org.downloadcenter.samsung.c...5728593/MCCI_WHQL_USB_Modem_Driver_4.40.7.exe
Good luck!
No luck
Misterjunky said:
During your unsuccessful flashing of the google edition rom you have lost ROOT and the custom and or stock recovery.
That is why you cannot go into recovery mode.
You are lucky that the .pit file did not flash, you could have ended up with a brick (unusable phone).
The .PIT file is the partition information table, if that is changed or damaged you would need to send
your phone to samsung or other phone repair shop to get it fixed.
What you need to do is to download and Odin flash the stock-rooted i9505 rom which can be found here:
(Removed link due to under 10 posts)
This rom is pre-rooted and you will be able to get into recovery mode without any issues.
Once this is odin flashed, be sure to make a nandroid backup before flashing other cwm/twrp zip file roms.
The "phone cannot be located" error most likely means that you either do not have the proper samsung usb
driver installed or you need to check the usb cable connections to your computer and phone.
Perhaps use a different usb cable and a different usb port will fix this issue.
Just in case you need it, here is the link for the official usb drivers for the samsung s4 phone:
(Removed link due to under 10 posts)
Good luck!
Click to expand...
Click to collapse
Firstly thank you so much for reaching out to help me with this matter. :good:
Sadly no such luck, running odin 3 v1.85
This is the result I had...
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMH1-PRE-ROOTED-DEODEX-SuperSlim.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Going to try again using the drivers you have provided (restarting now)
Still no luck...
Odin v1.85
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMH1-PRE-ROOTED-DEODEX-SuperSlim.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
With no readout on the phone (as if the process never took place)
& using v3.07
Odin v3.07
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMH1-PRE-ROOTED-DEODEX-SuperSlim.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Through all these process only AutoReboot was checked...
The last attempt on v3.07 had the same result as a previous flash in which the process bar appears on the phone in download mode, but fails with the same read out on the device..
ODIN MODE
PRODUCT NAME: GT-I9505
CURRENT BINARY: CUSTOM
SYSTEM STATUS: CUSTOM
CSB-CONFIG-LSB; 0x30
WRITE PROTECTION: ENABLE
START [224, 1440]
ODIN: FLASH READ FAILURE
EvilM0narch said:
Okay where do I start...
I was given this phone from a friend, and it was working fine,
rooted and no problems at all...
Followed this guide to install the "Google Play Edition" ROM >> http://www.technobuffalo.com/videos/how-to-turn-a-galaxy-s4-into-a-google-edition-phone/
All was working perfectly, then in a backup process using titanium backup, the phone crashed...
I'm stuck in a boot loop with only the Samsung Galaxy logo screen.
I can enter Download mode, but not recovery...
Have tried every ROM that I can think would be appropriate to restore but to no avail...
Even tried philz touch recovery, nothing seems to be working...
Odin always reports either write failed or There is no PIT partition.
Have tried writing just the .PIT file from >> http://forum.xda-developers.com/showthread.php?t=2265477
Have tried to recover using Kies, firmware downloads then "Error - F" Phone cannot be located...
The phone gets stuck with a small dot of a process bar in download mode and this read out in the top left of the screen:
ODIN MODE
PRODUCT NAME: GT-I9505
CURRENT BINARY: CUSTOM
SYSTEM STATUS: CUSTOM
CSB-CONFIG-LSB; 0x30
WRITE PROTECTION: ENABLE
START [224, 1440]
ODIN: FLASH READ FAILURE
I'm at a total loss how to recover this, and if it's even possible to recover?
I would happily send it somewhere for repair, I have no warranty so i expect to pay, but no idea where to send?
Does any one have any advice or solution to this problem?
Much appreciated.
Click to expand...
Click to collapse
Are you definitely using PDA (not Phone) mode in Odin when flashing ROMs? Also are you running Odin using 'administrator' mode if using Windows?
Sent from my Nexus 7 using xda app-developers app
PDA
gsmyth said:
Are you definitely using PDA (not Phone) mode in Odin when flashing ROMs? Also are you running Odin using 'administrator' mode if using Windows?
Sent from my Nexus 7 using xda app-developers app
Click to expand...
Click to collapse
Yes 100% sure that I'm selecting PDA and Admin privileges.
Honestly I'm baffled I'm now charging the battery now to ensure the phone has enough to attempt this process again.
The battery icon fails to display a meter... Just an empty battery with a loading circle inside, assuming this is because the phone cannot access the images for the battery charging display? (The display that is present when the phone if turned off and you are charging)
I'm still stumped with what to try here. Any suggestions?
I'm sure if I can get at least back into recovery mode I could resolve it, but with odin failing due to pit each time it's just like banging my head against a wall :silly:
Screen Capture
Attached is a capture of the process using odin
Hope this can help in some way...
Edit: wrong thread
EvilM0narch said:
Attached is a capture of the process using odin
Hope this can help in some way...
Click to expand...
Click to collapse
No pit partition = YOUR PARTITION TABLE IS CORRUPTED. flash stock firmware with pit file in Odin 3.04, untick "auto-reboot", when it "pass", take off battery, inset it, boot into recovery, reset the phone, reboot
Sent from my Galaxy Nexus using xda premium
FAIL
samersh72 said:
No pit partition = YOUR PARTITION TABLE IS CORRUPTED. flash stock firmware with pit file in Odin 3.04, untick "auto-reboot", when it "pass", take off battery, inset it, boot into recovery, reset the phone, reboot
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Thanks for this, have tried flashing with the rom that Misterjunky provided (with pit from samersh72) and fail
also tried the EE rom I found on the forum that samersh72 provided (with pit from samersh72) fail
tried flashing just the pit alone... fail
**making sure that "auto-reboot" was unticked**
In each process >> re-partition operation failed?
:crying:
I'm now downloading the EE rom direct from sammobile (Although for some reason I'm sure this device was originally Orange network)
Will update the situation when all has downloaded and I can try again.
Thanks to all for your input on this.
EvilM0narch said:
Thanks for this, have tried flashing with the rom that Misterjunky provided (with pit from samersh72) and fail
also tried the EE rom I found on the forum that samersh72 provided (with pit from samersh72) fail
tried flashing just the pit alone... fail
**making sure that "auto-reboot" was unticked**
In each process >> re-partition operation failed?
:crying:
I'm now downloading the EE rom direct from sammobile (Although for some reason I'm sure this device was originally Orange network)
Will update the situation when all has downloaded and I can try again.
Thanks to all for your input on this.
Click to expand...
Click to collapse
re-partition must work. make sure that you are using the right pit for your variant, unzip it before putting it in pit window in odin
flash your original EE official rom from sammobile
Making sure all is right
samersh72 said:
re-partition must work. make sure that you are using the right pit for your variant, unzip it before putting it in pit window in odin
flash your original EE official rom from sammobile
Click to expand...
Click to collapse
Pit variant I have is from you for my device "i9505", so that would be the correct pit file?
Still waiting on the EE official rom from sammobile to download, as long as all is correct I will try again once downloaded.
Flash MH8 or newer...
In my case it was not possible to downgrade... i think that if you flash a mh8 or higher, after that is not possible downgrade because new bootloaders.
Enviado do meu GT-I9505 utilizando Tapatalk 4
MH8
sanespro said:
Flash MH8 or newer...
In my case it was not possible to downgrade... i think that if you flash a mh8 or higher, after that is not possible downgrade because new bootloaders.
Enviado do meu GT-I9505 utilizando Tapatalk 4
Click to expand...
Click to collapse
Reading more on this it does seem you are right, can you elaborate as to what is mh8?
Is this a specific rom? Reading what I could find it seems it will only allow custom roms on the device or a rom that is MH8?
Can anyone shed some light on this?
Going to download the latest BTU MH8 for UK and give that a try? Hopefully I'm making progress as the MH8 rule would explain why it's not working
EvilM0narch said:
Reading more on this it does seem you are right, can you elaborate as to what is mh8?
Is this a specific rom? Reading what I could find it seems it will only allow custom roms on the device or a rom that is MH8?
Can anyone shed some light on this?
Going to download the latest BTU MH8 for UK and give that a try? Hopefully I'm making progress as the MH8 rule would explain why it's not working
Click to expand...
Click to collapse
be aware MH8 firmware will lock your bootloader, so you will not be able to downgrade.
your problem is in partition table. your solution is with the pit file flashed with your stock firmware.
if it fail, see odin troubleshooting in my thread
samersh72 said:
be aware MH8 firmware will lock your bootloader, so you will not be able to downgrade.
your problem is in partition table. your solution is with the pit file flashed with your stock firmware.
if it fail, see odin troubleshooting in my thread
Click to expand...
Click to collapse
I believe I am already flashed to MH8, but I am not sure.
I have tried flashing the pit located in your sig for my GT-I9505 but it always fails?
Is there something else I am missing or not doing correctly? I have been following each guide and double checking the steps before I try anything.
No matter what action i take the pit flash with the file "I9505_pit file.zip" located here >> http://forum.xda-developers.com/showthread.php?t=2265477
always fails? I have no idea why? Or which steps to take.
Sorry to be such a pain,
EvilM0narch said:
I believe I am already flashed to MH8, but I am not sure.
I have tried flashing the pit located in your sig for my GT-I9505 but it always fails?
Is there something else I am missing or not doing correctly? I have been following each guide and double checking the steps before I try anything.
No matter what action i take the pit flash with the file "I9505_pit file.zip" located here >> http://forum.xda-developers.com/showthread.php?t=2265477
always fails? I have no idea why? Or which steps to take.
Sorry to be such a pain,
Click to expand...
Click to collapse
yes this is the right pit file.
Odin troubleshooting: If Odin accidentally gives you "fail" try the following:
- Repeat procedure.
- Make sure that all actions of Kies are disabled from task manager.
- Change usb port.
- Try another usb cable (make sure it is the original).
- Try another Odin version.
- Uninstall and re-install driver.
- Use pit file.
- Try another computer.
Another machine...
samersh72 said:
yes this is the right pit file.
Odin troubleshooting: If Odin accidentally gives you "fail" try the following:
- Repeat procedure.
- Make sure that all actions of Kies are disabled from task manager.
- Change usb port.
- Try another usb cable (make sure it is the original).
- Try another Odin version.
- Uninstall and re-install driver.
- Use pit file.
- Try another computer.
Click to expand...
Click to collapse
Have tried all except another computer, someone mentioned that an XP based machine works best.
Those are like gold-dust around here, I will try this process on a laptop and see if I can get it to work... That seem to be my best bet for now
Again kudos for all of the help and the quick replies. :good:
All hope seems lost....
After finally trying every method on this PC
(All versions of Odin I could find, all usb ports, original usb lead, kies is disabled, drivers un-installed/re-installed)
And having no luck...
I have had some different results on the laptop;
all other versions of odin I tried (v1.83, v1.85, v3.04, v3.06) just fail;
(again all usb ports, original usb lead, kies is disabled, drivers un-installed/re-installed)
And this read out...
flashing pit and rom > Complete(write) operation failed.
flashing only pit > Complete(write) operation failed.
However on Odin3 v3.07
flashing pit and rom > There is no pit partition
flashing only pit > There is no pit partition
and on v3.09
flashing pit and rom > re-partition operation failed.
flashing only pit > re-partition operation failed
I'm at a total loss now. I have a chance to send it back to cash generator as thats where my friend had purchased it from.
Is it worth doing so?
Any one have any thoughts or suggestions to aid this situation?
:crying:
I guess my only option here as I cannot get it to flash, is to either sell the phone in the state it is in.
Or send it back to Cash Generator to see if they will replace/refund it.
:crying:
samersh72 said:
yes this is the right pit file.
Odin troubleshooting: If Odin accidentally gives you "fail" try the following:
- Repeat procedure.
- Make sure that all actions of Kies are disabled from task manager.
- Change usb port.
- Try another usb cable (make sure it is the original).
- Try another Odin version.
- Uninstall and re-install driver.
- Use pit file.
- Try another computer.
Click to expand...
Click to collapse
Okay so just got my device back from my friend with the Jtag, and this is the report he run for me
===============
= JTAG REPORT =
===============
Open serial port...OK
Connecting to the RIFF Box...OK
Connecting to the dead body...OK
Detected dead body: DETECTED
Set I/O Voltage reads OK, TCK Frequency is OK
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Flashing the dead body...
No Resurrection Data is available for the eMMC Chip with Capacity = 0B
ERROR: Failed use to Resurrection Data for the eMMC Chip with Capacity = 0B
ERROR: Selected FLASH Chip was not initialized by the DCC Loader.
Where can I get eMMC chip repaired?
Hi, i have a big problem. Everytime when i flash something in odin i have FAIL.
Today i want to flash stock MGA. After a few seconds... fail.
Here log from odin 3.07:
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
I can't go into recovery.
I can go into download mode.
I think i tried everything..
PLEASE HELP BECAUSE I NEED MY PHONE ON TOMMOROW.
sorry for my bad english
Any help ??
kapiszon53 said:
Any help ??
Click to expand...
Click to collapse
Odin troubleshooting: If Odin accidentally gives you "fail" try the following:
- Repeat procedure.
- Make sure that all actions of Kies are disabled from task manager.
- Change usb port.
- Try another usb cable (make sure it is the original).
- Try another Odin version.
- Uninstall and re-install driver.
- Try another computer.
After change computer everything works fine. THX
i've used a different PC, reinstalled the USB drivers and repeated the process many times but still it doesn't work
i've a GT-I9500
Hello, i have searched the forums for a flashable firmware upgrade from 4.2.2 to 4.3 for my sgs4 (i9506) and can't find it anywhere, could someone please locate me to the correct directions or atleast tell me something working? Thanks
mattish.91 said:
Hello, i have searched the forums for a flashable firmware upgrade from 4.2.2 to 4.3 for my sgs4 (i9506) and can't find it anywhere, could someone please locate me to the correct directions or atleast tell me something working? Thanks
Click to expand...
Click to collapse
Check sammobile.com then firmware for ur phone. Have a nice day
Sent from my Phone.
Edit: or here http://www.sammobile.com/firmwares/2/
Repulsa said:
Check sammobile.com then firmware for ur phone. Have a nice day
Sent from my Phone.
Click to expand...
Click to collapse
I just flashed the "I9506XXUBML5_I9506FTMBML1_I9506XXUBMK7_HOME.tar.md5" and i get "failed" and now i can't acces my phone, only download mode... please help
mattish.91 said:
I just flashed the "I9506XXUBML5_I9506FTMBML1_I9506XXUBMK7_HOME.tar.md5" and i get "failed" and now i can't acces my phone, only download mode... please help
Click to expand...
Click to collapse
Download odin 3.09 then select PDA, and find the file you download now connect the one cable to your PC and press power+volume down to your phone until u reach download mode and connect the other cable to your phone and click start.
Edit: Dont root your device you might Void your warranty after updating.
mattish.91 said:
Hello, i have searched the forums for a flashable firmware upgrade from 4.2.2 to 4.3 for my sgs4 (i9506) and can't find it anywhere, could someone please locate me to the correct directions or atleast tell me something working? Thanks
Click to expand...
Click to collapse
What u flashed is only for France Orange branded. They dont have 4.3 for others still
Repulsa said:
Download odin 3.09 then select PDA, and find the file you download now connect the one cable to your PC and press power+volume down to your phone until u reach download mode and connect the other cable to your phone and click start.
Edit: Dont root your device you might Void your warranty after updating.
Click to expand...
Click to collapse
Read this .. http://forum.xda-developers.com/showthread.php?t=2582135&page=2
---------- Post added at 02:12 AM ---------- Previous post was at 02:12 AM ----------
mattish.91 said:
I just flashed the "I9506XXUBML5_I9506FTMBML1_I9506XXUBMK7_HOME.tar.md5" and i get "failed" and now i can't acces my phone, only download mode... please help
Click to expand...
Click to collapse
Read this..... http://forum.xda-developers.com/showthread.php?t=2582135&page=2
If you do really want to upgrade after you read the upper report i can help you cause Odin and Heimdall are no more supported and you cant downgrade anymore to 4.2.2
So think about it twice
And please read here too http://forum.xda-developers.com/showpost.php?p=45666586&postcount=1 ^^
I got 5 buttons in odin and no one says "PDA" i know it's not "PIT" and the other ones are "BL, AP, CP, CSC" i guess it should be "AP" since that button is in the same place as "PDA" should be, and i still get failed when using Heimdall, i have also tried to download root, but since the download speed is so damn low from that site i cant get it... what am i doing wrong?
This is what i get:
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
xenix96 said:
Read this .. http://forum.xda-developers.com/showthread.php?t=2582135&page=2
---------- Post added at 02:12 AM ---------- Previous post was at 02:12 AM ----------
Read this..... http://forum.xda-developers.com/showthread.php?t=2582135&page=2
If you do really want to upgrade after you read the upper report i can help you cause Odin and Heimdall are no more supported and you cant downgrade anymore to 4.2.2
So think about it twice
And please read here too http://forum.xda-developers.com/showpost.php?p=45666586&postcount=1 ^^
Click to expand...
Click to collapse
Hey mate Read this :Edit: Dont root your device you might Void your warranty after updating < its a warning
mattish.91 said:
I got 5 buttons in odin and no one says "PDA" i know it's not "PIT" and the other ones are "BL, AP, CP, CSC" i guess it should be "AP" since that button is in the same place as "PDA" should be, and i still get failed when using Heimdall, i have also tried to download root, but since the download speed is so damn low from that site i cant get it... what am i doing wrong?
This is what i get:
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Bro Please remember if you update your phone to newest 4.3, there is no more chance for you to downgrade your system , and if you root/custom your phone / you will Void your Warranty , just like they said on i9506 thread to wait until someone make a custom rom in order NOT to void that warranty for your phone.
Repulsa said:
Hey mate Read this :Edit: Dont root your device you might Void your warranty after updating < its a warning
Bro Please remember if you update your phone to newest 4.3, there is no more chance for you to downgrade your system , and if you root/custom your phone / you will Void your Warranty , just like they said on i9506 thread to wait until someone make a custom rom in order NOT to void that warranty for your phone.
Click to expand...
Click to collapse
Yea. i got that, but now i can't use the phone so how do i reset it? kies doesnt work, and i can't find a proper 4.2.2 that i can flash with odin, root is not required atm...
mattish.91 said:
Yea. i got that, but now i can't use the phone so how do i reset it? kies doesnt work, and i can't find a proper 4.2.2 that i can flash with odin, root is not required atm...
Click to expand...
Click to collapse
Hello again , try here http://www.sammobile.com/firmwares/1/?model=GT-I9506&pcode=EVR#firmware Hope it helps and choose your country.
Repulsa said:
Hello again , try here http://www.sammobile.com/firmwares/1/?model=GT-I9506&pcode=EVR#firmware Hope it helps and choose your country.
Click to expand...
Click to collapse
Still can't download from those sources since they are too slow, can someone upload it somewhere else please? im allways getting interupted download...
mattish.91 said:
Still can't download from those sources since they are too slow, can someone upload it somewhere else please? im allways getting interupted download...
Click to expand...
Click to collapse
I cant try to download the file i have a 50/50 mbps and make a mirror for you but i need to know what file are you tring to download baseband, country , Carrier and such. have a nice day.
Repulsa said:
I cant try to download the file i have a 50/50 mbps and make a mirror for you but i need to know what file are you tring to download baseband, country , Carrier and such. have a nice day.
Click to expand...
Click to collapse
This is the file: http://samsung-updates.com/details/18144/Galaxy_S4_LTE-A/S800/GT-I9506/HTS/I9506XXUAMJ2.html the source is your's Thanks you'r awesome!
mattish.91 said:
I got 5 buttons in odin and no one says "PDA" i know it's not "PIT" and the other ones are "BL, AP, CP, CSC" i guess it should be "AP" since that button is in the same place as "PDA" should be, and i still get failed when using Heimdall, i have also tried to download root, but since the download speed is so damn low from that site i cant get it... what am i doing wrong?
This is what i get:
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Yes, AP is correct. Try a different data cable.
Enviado desde mi GT-P7510 usando Tapatalk 2
mattish.91 said:
This is the file: http://samsung-updates.com/details/18144/Galaxy_S4_LTE-A/S800/GT-I9506/HTS/I9506XXUAMJ2.html the source is your's Thanks you'r awesome!
Click to expand...
Click to collapse
Hello again here is the 4.2.2 firmware for your GT-I9506 , Make sure to Follow the instruction. and hoping to fix your problem, Have a nice day.
Gt-19506 4.2.2 Firmware https://mega.co.nz/#!XV4wRZ6b!LEDB9WuyI9SLUjqDsPrlBhTRSo9z1Sz6uWRCiq74qE8
Instructions For Flashing Firmware:
- Extract (unzip) the firmware file
- Download Odin3 v3.09 (From https://mega.co.nz/#!UdRRyCAT!H4FyVxYynNWvXqRNmnpMGQRCP-dG3uykgP2pT4rh8Ek)
- Extract Odin .ZIP file
- Open Odin3 v3.09
- Restart phone in download mode (Press and hold Power + Volume down buttons) in order to reach download mode.
- Connect phone and wait until you get a blue sign in Odin
- Add I9506XXUAMJ2_I9506HTSAMJ2_I9506XXUAMI1_HOME.tar.md 5 to AP
- Make sure re-partition is NOT ticked
- Click start button, and wait a few minutes.
-Your phone should automatically reboot after completion
-You can now disconnect your phone from computer .
- If you encounter any issues with the firmware (Any FC, Bootloop etc)
- Boot into recovery mode (power+vol up)
- Choose to wipe/factory reset. (THIS WILL ERASE ALL OF YOUR DATA INCLUDING YOUR INTERNAL SD CARD!)
- Then choose reboot and you should be good to go!
Repulsa said:
Hello again here is the 4.2.2 firmware for your GT-I9506 , Make sure to Follow the instruction. and hoping to fix your problem, Have a nice day.
Gt-19506 4.2.2 Firmware https://mega.co.nz/#!XV4wRZ6b!LEDB9WuyI9SLUjqDsPrlBhTRSo9z1Sz6uWRCiq74qE8
Instructions For Flashing Firmware:
- Extract (unzip) the firmware file
- Download Odin3 v3.09 (From https://mega.co.nz/#!UdRRyCAT!H4FyVxYynNWvXqRNmnpMGQRCP-dG3uykgP2pT4rh8Ek)
- Extract Odin .ZIP file
- Open Odin3 v3.09
- Restart phone in download mode (Press and hold Power + Volume down buttons) in order to reach download mode.
- Connect phone and wait until you get a blue sign in Odin
- Add I9506XXUAMJ2_I9506HTSAMJ2_I9506XXUAMI1_HOME.tar.md 5 to AP
- Make sure re-partition is NOT ticked
- Click start button, and wait a few minutes.
-Your phone should automatically reboot after completion
-You can now disconnect your phone from computer .
- If you encounter any issues with the firmware (Any FC, Bootloop etc)
- Boot into recovery mode (power+vol up)
- Choose to wipe/factory reset. (THIS WILL ERASE ALL OF YOUR DATA INCLUDING YOUR INTERNAL SD CARD!)
- Then choose reboot and you should be good to go!
Click to expand...
Click to collapse
This is my result:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9506XXUAMJ2_I9506HTSAMJ2_I9506XXUAMI1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
so this wasn't working, any idea? xD
mattish.91 said:
This is my result:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9506XXUAMJ2_I9506HTSAMJ2_I9506XXUAMI1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
so this wasn't working, any idea? xD
Click to expand...
Click to collapse
You are trying to flash a stock 4.2.2 over a 4.3 knox bootloader!!!! If course you will get error!!!!
Since you have 4.3 knox bootlader, you only can flash stock 4.3 roms. Download the last update for your model from sammobile and reflash again with same process.
Enviado desde mi GT-I9500 usando Tapatalk 2
jaswinky said:
You are trying to flash a stock 4.2.2 over a 4.3 knox bootloader!!!! If course you will get error!!!!
Since you have 4.3 knox bootlader, you only can flash stock 4.3 roms. Download the last update for your model from sammobile and reflash again with same process.
Enviado desde mi GT-I9500 usando Tapatalk 2
Click to expand...
Click to collapse
im sorry, im totally lost and confused, what am i missing, there is only one 4.3 rom that is flashable throu odin and thats the french version and that should work in Sweden aswell, when i flash that rom i'm still getting that error, should i try to flash root before continuing? incase yes, which one? Im really grateful for all your help.
mattish.91 said:
im sorry, im totally lost and confused, what am i missing, there is only one 4.3 rom that is flashable throu odin and thats the french version and that should work in Sweden aswell, when i flash that rom i'm still getting that error, should i try to flash root before continuing? incase yes, which one? Im really grateful for all your help.
Click to expand...
Click to collapse
hello again , i did not know that you have a the newest bootloader for your phone and yet you requested a 4.2.2 anyways since your Knox void warranty is not 0x1 yet go ahead and send it back for repair , im sure they will fix this problem, since you did not void your warranty yet that's the best solution i can give you. or wait to someone here on xda know's how to fix this issue. have a nice day.
Repulsa said:
hello again , i did not know that you have a the newest bootloader for your phone and yet you requested a 4.2.2 anyways since your Knox void warranty is not 0x1 yet go ahead and send it back for repair , im sure they will fix this problem, since you did not void your warranty yet that's the best solution i can give you. or wait to someone here on xda know's how to fix this issue. have a nice day.
Click to expand...
Click to collapse
The problem is solvet simply flashed root, the only thing not working (so far) is keyboard xD and it is running 4.3
Okay so I am using a AT&T Galaxy S5, SM-G900A. I was being an idiot and I wiped everything on my phone. So now when I downloaded Odin, downloaded the SM-G900A stock firmware, tried to flash it with odin and I kept getting this error no matter what I do, someone please help me....
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900AUCU1ANCE_G900AATT1ANCE_G900AUCU1ANCE_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
When my phone is in download mode, after I get the error in odin heres what my phone says: SW REV CHECK FAIL : [aboot]Fused 2 > Binary 1
Nevermind, got it fixed. All thanks to Davew41's post: http://forum.xda-developers.com/showthread.php?t=2785363
Hi, I have j510fn and I was a rom tester,
I have a problem since I flashed
J510FNXXU2APK6_J510FNODD2APK2_J510FNXXU2APK2_HOME.tar.md5
to test light stock rom v3 from Kingraheel
what happens is that NOW I can't flash any other firmware by odin... when I click START it says FAIL and in my device there is this text in red
SW REV CHECK FAIL : [aboot]Fused 2 > Binary 1
I just want to flash my OFFICIAL firmware
J510FNXXU1APG1_J510FNPHE1APG1_J510FNXWU1APFC_HOME.tar.md5
but I can't... only APK6 firmware works on odin... any other firmware works.... can you help me?
I don't have any NANDROID backup of previous versions... only of my actual firmware... APK6
My computer does not detect my device... I have the drivers installed, and I tried on all the USB ports... it charges but not open files.... PLEASE HELP
TheWalkingSans said:
Hi, I have j510fn and I was a rom tester,
I have a problem since I flashed
J510FNXXU2APK6_J510FNODD2APK2_J510FNXXU2APK2_HOME.tar.md5
to test light stock rom v3 from Kingraheel
what happens is that NOW I can't flash any other firmware by odin... when I click START it says FAIL and in my device there is this text in red
SW REV CHECK FAIL : [aboot]Fused 2 > Binary 1
I just want to flash my OFFICIAL firmware
J510FNXXU1APG1_J510FNPHE1APG1_J510FNXWU1APFC_HOME.tar.md5
but I can't... only APK6 firmware works on odin... any other firmware works.... can you help me?
I don't have any NANDROID backup of previous versions... only of my actual firmware... APK6
My computer does not detect my device... I have the drivers installed, and I tried on all the USB ports... it charges but not open files.... PLEASE HELP
Click to expand...
Click to collapse
have you tried a different cable? I know it sounds rather sophomorish, but its a very common cause of the computer not being able to flash via Odin. Or can you get to another computer to try it there?
youdoofus said:
have you tried a different cable? I know it sounds rather sophomorish, but its a very common cause of the computer not being able to flash via Odin. Or can you get to another computer to try it there?
Click to expand...
Click to collapse
I just changed CSC with solid explorer, and flashed another stock firmware from samfirm downloader
But my computer continues without detecting my device... but ODIN does
TheWalkingSans said:
I just changed CSC with solid explorer, and flashed another stock firmware from samfirm downloader
But my computer continues without detecting my device... but ODIN does
Click to expand...
Click to collapse
that is odd indeed. I have 4 computers that all recognize all of my samsung phones. Are you getting the unrecognized device message in the area down by the clock?
My other computer detects it, okay, but I still cant flash any other stock firmware by odin AND BEFORE I COULD
---------------------------------------
EVERYTHING SOLVED, SAME PROBLEM? CONTACT ME
Here is HOW I SOLVED IT:
This error happens when you before have updated from "U1" to "U2" and then you try to flash a firmware with "U1" (UX appears in the firmware "name")
So, the simple solution is to flash the stock firmware with the same "UX" that you had before your device gor bricked.
In my case, testing KingRaheel's ROMS I flashed an Indian firmware (...U2APK6...) at this moment I didn't know I ****ed up. But don't worry, I simply had updated the "U" and how I didn't know it, I tried to flash lots and lots of firmwares with "U1" without knowing what was happening. After long nights, I tried to flash my last firmware from SPAIN (PHE) with "U2" and it worked.
I hope I helped you. I used SM-J510FN (J5 2016)
If you have another device, try the same but with your current model, any questions, ask by twitter/dm
Sent from my SM-J510FN using XDA Labs
Hello everyone,
I'm trying to flash a stock rom on a Verizon GS5. I say trying because so far it hasn't been working, unless I'm doing something wrong, which I think I am. When I got the phone, it had a Sprint rom flashed to the GS5. The original Verizon IMEI under the battery is clean and verified good with Verizon. There is nothing physically or cosmetically wrong with the phone, it powers on sometimes and randomly restarts. When it does turn on, the Sprint Spark logo comes up, the phone boots up normally and then randomly shuts off, taking a long time to be able to power back on. The only way that it says on is by putting it on Download Mode.
When in download mode, it shows as a G900P,
As far as my understanding goes, shouldn't it be a G900V?
I attempted to flash a stock Verizon rom I downloaded and tried to flash it with Odin 3.04 but it fails each and every time. I have installed the Samsung drivers that I got from the website, I restarted the computer, I restarted the phone but Odin give me a fail error.
Then I tried a newer version of Odin 4.43 but I'm not sure I'm using that one correctly but it's not working for me either.
I left the phone in Download Mode and it has been on for about 30 mins (the longest so far without it restarting on me).
Is there something that I'm missing here? Something else I could try to fix this?
Any ideas? Suggestions?
Any help would be greatly appreciated!!
..
-> It's a Verizon Galaxy S5 Phone I got from eBay
-> It's flashed with the Sprint rom version of the GS5
-> The phone restarts on and off, randomly, unless it is in Download Mode
-> I want to flash it back to the original Verizon GS5 rom.
-> I attempted to flash the phone with Odin 3.09 and rom SM-G900V_VZW_1_20140331185350
-> I get an error message when using Odin 3.09, it FAILS
-> The progress bar in the GS5 phone advances a small amount but that's it.
-> I attempted to use Odin 4.43 with the same rom file but that also fails and I get an error message.
-> I researched on Google before signing up and asking for help.
-> I have read many Threads and Posts on several Forums, and I have also tried many tutorials without any luck.
-> I researched how to use Odin, there is lot's of pictures, easy explanations but that's not it.
-> I found a GS5 stock rom, file name mentioned above.
-> Samsung drivers are installed, phone is recognized by Odin.
1.) Am I using the correct rom?
2.) Which version of Odin should I use?
..
SewerDweller said:
Hello everyone,
Any ideas? Suggestions?
Any help would be greatly appreciated!!
Click to expand...
Click to collapse
Download this version of Odin and extract the folder in the zip.
Make sure you have downloaded the correct firmware, extract the MD5 / tar file from inside the firmware.zip file you downloaded and put it in the Odin 3.07 folder
Start Odin.exe, put your phone in download mode and connect to your PC, if you have Kies installed make sure it is not running, Odin and Kies don't mix.
Once you have the Blue ID.COM indicated, click on PDA, find the MD5 / .tar file wait for teh file check Odin runs then click Start, wait for Odin to finish and your phone reboots.
Guide for Odin use here it is from the S3 but the use of Odin is the same for the S5
It took me a while to get it to turn on but here's what I got from trying ag4751's suggestions.
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900VVRU1ANI2_G900VVZW1ANI2_G900VVRU1ANI2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
It's the same thing that I was getting before, I'm sorry if I did not explain myself in detail at first.
I have used 2 versions of Odin 3.09 (which I used on my own and got the above message).
3.07 as suggested by ag4751.
I have used 2 different roms and both fail.
->G900V_VZW_1_20140331185350
->G900VVRU1ANI2-20140919141518
@fffft
To answer your question as to what tutorial I followed, I followed ag4751's tutorial/explanation on his reply. It's basic, just like all the other tutorials I googled.
1.) Put the phone in download mode
2.) Open Odin
3.) Select PDA
4.) Wait for the file check
5.) Click start
and then it fails.
That's what @ag4751 suggested, that's what I tried, that's what I tried before, that's what I'm trying now and all that is failing for some reason.
..
..